Eiki LC XNB3 Multimedia Projector
Contents
1. 232 If a subset of functionality appears to be working verify that both types of control wiring are correctly wired When try to turn the projector on the warming indicator red LED blink The projector is in the default configured lockout state and the Panel is waiting for its internal lockout timer to expire This feature protects the projector s bulb Be sure to let your client know about this behavior IV TECHNICAL NOTES 1 By default projector power is verified by polling every few seconds via the RS 232 port Power polling can be suspended by depressing and holding the On key polling will be restored when the key is released Should the Eiki power off the Panel will usually detect this condition and power off within twenty seconds Please READ THE SPECIAL CONTROL NOTE at the end of this document which explains how UNUSUAL PROJECTOR STATES COULD AFFECT POWER POLLING 2 The Eiki is controlled through both RS 232 and Infrared The projector cannot be configured for wired serial 3 The lockout timer specifies the amount of time allowed between sending POWER OFF and POWER ON to the projector the delay allows the projector bulb to cool before re powering This delay can be configured using the Configuration Utility however adjusting the lockout timer delay is strongly discouraged as rapid re powering causes undue wear on the projector s bulb Also the Eiki will not allow power to be restored before a minimum delay has expire2. the holding the On key down Auto Image works only for the Computer input The hidden functions available for the Eiki with this Driver are as follows MENU FOCUS UP VIDEO MUTE ON ADJUST LEFT FOCUS DOWN VIDEO MUTE OFF ADJUST RIGHT ZOOM UP AUDIO MUTE ON ADJUST UP ZOOM DOWN AUDIO MUTE OFF ADJUST DOWN DIG ZOOM UP FREEZE ON SELECT DIG ZOOM DOWN FREEZE OFF AUTO PC ADJUST KEYSTONE UP KEYSTONE DOWN D Relays The following table specifies the factory preset settings for the low current relays found on the rear D of the SmartPanel The Configuration Utility can be used to customize these settings your installation RELAYS 500mA MAX CURRENT SELECTION ON ON OFF EXT SWITCHER CTRL See ae r a 25858 SESB SBKE O 010 00 O 010 00 9o 9 OIOSOS OSOSOSOS E Other Presets The following table specifies other default factory settings for this Driver that affect is control of the Projector Power Status Feedback Method RS 232 Power Polling see SPECIAL CONTROL NOTE and note 1 Control Wiring RS 232 and IR Emitter Control for the Eiki with this Driver is via RS 232 and an IR Emitter The following table specifies settings for the Panel s configurable timers For more information on the inactivity shutdown feature and the lockout timer see the SmartPanel Configuration and Installation Guide Lockout Timer 103 seconds se
3. 1 VIDEO VIDEO COMPUTER COMPUTER nici z ANA DiG 7 Input choices available for the Eiki with this Driver a are VIDEO COMPUTER ANALOG VGA a AN COMPUTER DIGITAL DVI AND MCI Not Always Available Special Note You must specify which VIDEO input you are using e g S Video Composite Video et cetera The VIDEO input selection can only specify one source due to the projector design Video type must be configured in the Video submenu on the projector C Hidden Function Mapping The following table specifies the factory preset hidden function mapping for this Driver The Configuration Utility can be used to customize these settings your installation Selection 1 SELECT AUTO PC ADJUST Selection 3 ADJUST LEFT Selection 4 ADJUST RIGHT CST MENU Off MENU Volume Up ADJUST UP ADJUST DOWN DR EIK02 12 19 01 SELECT D FREEZE ADJUST LEFT ADJUST RIGHT ADJUST NO SHOW SP Controls reserves the right to modify specifications without notice at any time SmartPanel Projector Driver Application Note Eiki LC NB3W Hidden functions names are based on the Eiki remote and controls on top of the projector Adjust controls navigation through onscreen menus Hidden functions are accessed by pressing the indicated key while
4. D Quick Start Reference Sheet SP Eiki LC NB3W Series Revision A NOTE This one page document is intended only as a quick reference for installation please read the SP Controls Application Note for a complete description of this projector driver prior to installation l Driver Features 1 Input Selection Mapping Selection 1 VIDEO Selection 2 COMPUTER ANALOG Special Note You must specify which VIDEO input you are using e g S Video Composite Video et cetera on the projector on screen menus See the Section Part B of the Application Note for more information 2 Hidden Function Mapping Default Configuration Using the ON button as a shift key press the following buttons to access the specified projector features ADJUST DOWN 3 Other Driver Features Power Status Feedback Method RS 232 Power Polling Control Wiring RS 232 and IR Emitter ll Wiring Specifications NOTE For a wiring diagram please see the SP Controls Application Note 1 RS 232 Wire the Panel RS 232 port to a male 8 pin mini DIN as follows TX to 1 RX to 6 GND to 8 Connect this mini DIN to the projector port labeled CONTROL PORT 2 Infrared Emitter Wire the Panel IR Serial port to a female 1 8 Mini as follows IR SER to tip GND to ring Connect to the included IR Emitter and attach the emitter bud to any projector IR window lll Additional Projector Information You ma
5. d Therefore disabling the lockout delay will cause potentially confusing Panel behavior Note that the Eiki has an atypically long power down phase approximately ninety seconds which results in an above average lock out time 2001 SP Controls Inc 601 Minnesota Suite 115 San Francisco CA 94107 help spconirols com SmartPanel Projector Driver Application Note Eiki LC NB3W V Special Control Note DISABLING POWER MANAGEMENT AUTO SHUT OFF The Eiki LC NB3W has an optional POWER MANAGEMENT function which will cause the projector to power off in 5 minutes if an input signal is not detected THE FACTORY DEFAULT OF THE PROJECTOR sets this function to ENABLED so IT SHOULD BE DISABLED DURING INSTALLATION This function is disabled using the on screen menus which are accessible by the remote control or through the hidden functions on the SmartPanel In order to disable POWER MANAGEMENT select the SETTING pull down menu and scroll down to POWER MANAGEMENT and press SELECT This will change the selection status to OFF which is the correct setting POWER POLLING ISSUES Due to the unique way the Eiki LC NB3W projector responds to power status queries it is possible that under very unusual conditions power polling could fail Specifically if the projector is experiencing a temperature abnormality such as overheating it may shut itself off while the Panel power status would not reflect this change In the event of an unexpected projector power
6. e note 3 Inactivity Shutdown Disabled 2001 SP Controls Inc 601 Minnesota Suite 115 San Francisco CA 94107 help spconirols com SmartPanel Projector Driver Application Note Eiki LC NB3W ll CONTROL WIRING PROJECTOR CONTROL RS232 IR SERIAL PRX 0x GND 12V lt qIR SER GND 9 P SENSE S O OIO gt crts HJO JJO HO 1 8 Mini Female Male Mini DIN ER TXto1 3 RX to 6 GND to 8 z amp 25S Es LW 5 cs 3 O amp NS RS 232 to IR Emitter to CONTROL PORT any IR window This section specifies how RS 232 and Serial IR should be wired to the Eiki projector A RS 232 should be connected to the Eiki control port labeled CONTROL PORT Connection should be as follows 1 Wire the Panel to a male 8 pin mini DIN as follows TX to 1 RX to 6 GND to 8 2 Connect this female DB9 to the projector port labeled CONTROL PORT B The IR Emitter should be connected to the one of the Eiki IR windows as follows 1 Wire the Panel to a female 1 8 Mini as shown wire IR SER to tip and GND to ring Splicing and direct wiring to the IR Emitter is not recommended as it makes removal of the Panel for service more difficult 2 Connect the included IR Emitter to the female mini 3 Affix the IR Emitter to one of the IR windows on the projector Emitter glows red when IR is emitted so wiring can be verified 2001 SP Co
7. if a power polling failure of this kind is observed this is likely what has occurred Note that a SmartPanel power polling failure will INNO WAY INTERFERE WITH THE PROJECTOR S AUTO COOLING ROUTINE and WILL NOT ENDANGER THE PROJECTOR IN ANY WAY Once the status of the projector has returned to normal power polling will automatically resume correctly it is only during the abnormal projector state that it will potentially be out of sync Although this problem should not be significant in the life of the installation if a determination is made that this situation is unacceptable projector power verification can be alternately provided with a third party current sensor This will ensure 100 accuracy in power polling for all possible projector states Please see the SmartPanel Configuration and Installation Guide section on Using a Power Current Sensor pg 30 for more information on this option VI REVISION HISTORY 1 Revision A December 2001 nitial release 2001 SP Controls Inc 601 Minnesota Suite 115 San Francisco CA 94107 help spcontrols com
8. ntrols Inc 601 Minnesota Suite 115 San Francisco CA 94107 help spconirols com SmartPanel Projector Driver Application Note Eiki LC NB3W Ill TROUBLESHOOTING Additional tips can be found in the SmartPanel Configuration and Installation Guide The Panel s not switching the projector to the S Video Composite Video YUV input When the VIDEO input is selected on the Panel the Panel switches the projector to the video input The projector must be configured via on screen menus in the VIDEO submenu to define which of the video inputs it is using The LC NB3W can t use multiple video inputs simultaneously The Panel does not do anything at all When power is applied to the Panel it should run through a brief power on self test during which all of the Panel lights will turn on and off in sequence If you do not see this self test make sure power is connected correctly and that polarity is correct The Panel keeps turning itself off even though the projector is on The Panel turns itself off when power polling indicates that the projector is off Check to make sure the RS 232 connection is correctly wired it is extremely unlikely other control would work and power polling not The Panel has only partial control over the Eiki Verify that both RS 232 and the Infrared Emitter are correctly wired The most common error is reversal of RX and TX for RS232 and polarity reversal of the IR emitter Note that the Eiki is controlled using both IR and RS
9. y wish to disable the POWER MANAGEMENT feature In order to disable POWER MANAGEMENT select the SETTING pull down menu and scroll down to POWER MANAGEMENT and press SELECT This will change the selection status to OFF which is the correct setting DR EIK02 12 19 01 SP Controls reserves the right to modify specifications without notice at any time Projector Driver Application Note Eiki LC NB3W Series Revision A This document describes the SmartPanel Projector Driver for the Eiki LC NB3W projector For more information on configuring and using the Panel see the SmartPanel Configuration and Installation Guide NOTE This projector requires a control cable terminated in a male 8 pin mini DIN and no adapter cable is provided Be sure that you have the appropriate mini DIN terminations available for installation Please read the SPECIAL NOTE in Section V of this document for important information on disabling the Power management option on the LC NB3W and how unusual power states in the Eiki projector could affect power status feedback I PROJECTOR CONTROL A Volume and Power Control Volume control on the Eiki is relative Absolute volume control is only possible with the optional SP Controls Audio Follow Video Pre Amplifier B Input Selection Mapping The following table specifies the factory preset input mapping for this Driver The Configuration Utility can be used to customize these settings your installation Selection
Download Pdf Manuals
Related Search