Sunpentown WA-9010E Portable Air Conditioner
Contents
1. stopper Do not use the unit in a very narrow room with obstacles to avoid breakdown Do not use the unit under direct sunlight to avoid surface color change Do not use the unit in or near water to avoid possible shock of electricity Do not use near gas appliances fire or the vicinity of flammable liquids Do not use with a damaged or improper A C socket When unplugging the unit hold the power plug securely and pull carefully Keep the unit one meter away from TV sets or radios to avoid electromagnetic interference Keep a distance between the air outlet and wall or furniture to avoid overheating Do not spray with insecticide or other chemicals as the plastic case may discolor or become deformed TROUBLESHOOTING ried 1 Te e ANA e Before seeking repair or service please first check the following Trouble Action Is power out Is it unplugged or plug loose Is power fuse or switched off If drain tank indicator lit If the water tank placed correctly If SET TIME suitable Air conditioner does not operate at all Is air inlet or outlet blocked Is there any other heat source in room Are air filters dirty Is SET TEMP suitable Is fan speed set at low Is unit in an open space Cooling efficiency is not good Too noisy or vibration Is it level Is the voltage of the power source normal Does the air exhaust have many bends or curves Is the air exhaust e2. si t Fd n T REPRE os Sx T WATER DRAINAGE When in cooling or dehumidifying mode the condensation will drain into the tank When the tank gets full the WATER FULL indicator will flicker As shown in the Fig 1 2 and 3 pull out the water tank pour out the water inside the tank then push it back to its original position CAUTION 1 When in cooling or dehumidifying mode do not remove the water tank or the compressor will stop and mode will change to FAN 2 f you want to take out the tank before the water becomes full please stop the machine first and wait for 3 minutes to prevent the water spilling into the unit 3 There is a plastic pipe inside where the tank is placed Do not remove the stopper while the unit is working as the water is used for cooling the copper duct MAINTENANCE on DA Uu eee MAINTENANCE METHODS Unplug the unit before cleaning Make sure there is no power to the unit before beginning to maintain or repair to prevent accident caused by electric shock Do not use chemical solvent like benzene or alcohol glazer to clean the surface of the unit which will scratch damage or deform the casing NOTE it is important to clean the exhaust air intake area located on the side and back near bottom with a vacuum to remove dust accumulation Excessive dust may cause a decrease in performance and or damage to the compressor Damage caused by improper maintenance wil
3. 3 set stretches from 19 1 2 to 78 3 4 Window exhaust adapter flat mouth 1pc Unit exhaust adapter round 1pc Adjustable window slider kit 2 set from 26 5 8 to 48 3 8 Drain hose connector 1pc continuous drain option hose not included NOTE Exterior drain hose extension is not included with this unit but can be purchased through any local Hardware Store Continuous Drainage 1 Remove the seal of drainage tube as shown in image 2 Extend the tube outside the unit for drainage as shown 3 Pay attention to place the tube in a proper situation to avoid causing the electric controls to not work properly Power cord storage Fix the roll wire at the back of the air guide plate with the clasp Wrap the power cord around the clasp when unit is not in operation CONTROL PANEL FUNCTIONS TIMER Button SWING Button FAN SPEED Button Press this button to Selection of this button Press this button will switch on switch off or will determine the air choose high medium delete timer delivery in swinging or low speed of air or fixed direction mode delivery FAN SPEED HIGH MED LOW SWING fx Lon COMP WATER FULL TIME Button TEMP Button Sets remaining Sets the COMPRESSOR WATER Indication Light diui indication light time for timer room operation temperature Operation mode Fan speed in
4. Warranty does not include freight charges Note For service please call 800 330 0388 or visit www spt usa com SUNPENTOWN INT L INC This GUARANTEE is in addition to your Statutory Rights Dear Customer Please keep this warranty for your record DO NOT return it oales Inquiries 800 934 9194
5. CONDITIONER please read this instruction manual carefully so that you get the best from the unit This instruction manual is used for guidance and does not form part of a contract We reserve the right to make technical changes without prior notice ACCESSORIES PARTS AND FUNCTIONS SSIES IN ced FRONT control panel up down air swinging louvers left right air swinging louvers E air outlet E 2 1 handle water tank power cable caster BACK upper air inlet grill hot air outlet grill AC hose adapter x 2 lower air inlet grill window kit adapter 2 qc remote Selection of installation location Place the portable air conditioner on a flat surface where the air outlets are not blocked Place the unit with at least 20 inches of clearing from a wall or other obstacles 32 7 inch Installing the air exhaust duct 1 Fix adaptors onto hose by turning clock wise 2 Fix the square end of the duct to the exhaust terminal of the unit 3 Lead the other end to the nearest window Note the length of the hose is between 23 7 70 inches Do not extend beyond the supplied length Keep hose length as short and as straight as possible hot a ir terminal ist air opening ct Correct mounting shown below If mounting through wall the height of the
6. hole should be between 16 51 inches from the floor MS 4 51 Wy LL INSTALLATION Le LH m de El WEE Example WRONG mounting diagram Air exhaust bend is too large will cause overheating Window Kit Installation Your window kit has been designed to fit most standard vertical and horizontal window applications However it may be necessary for you to improvise modify some aspects of the installation procedures for certain types of windows Please refer to Fig 24 amp Fig 24a for minimum and maximum window openings BER v Minimum y in Minimum 26 inches Maximum inches Mammur 48 ie inches Water Tank Safety Feature This unit is equipped with a fail safe switch mechanism which prevents the unit from condensing water in the event the water tank is accidentally displaced and or FULL with water If this situation occurs the WATER FULL indicator light will flash red continuously until the water tank is correctly positioned and or emptied NOTE The fan motor will continue to operate under this condition This is normal but no cooling or dehumidifying will occur until the tank is emptied and or correctly installed It may take several minutes before the compressor resumes normal operation INSTALLATION ee nn He orc reer d Noct A AL Installation Accessories Fig 25 Fig 25 Installation Accessories Flexible exhaust hose with adapters
7. to select left right swinging or fixed air delivery HOLD button Press this button to lock or unlock the keypad PRESENT TIME SETTING PROCEDURE When batteries are inserted the time is automatically set to 12 00AM Slide battery cover downward to open remote To set clock example set to 10 30AM Open the back cover push the CLK button with the tip of a ball pen The time indicator will start to flicker You may now set the present time Press the CLK button again and close the back cover NOTE Clock is only on the remote and not on the unit s control panel OPERATING T li A LL A tes rau d A 1 DEHUMIDIFYING AND COOLING OPERATION The operating range for cooling is between 63 F 88 F The operating range for dehumidifying is 68 F 88 F POWER SOURCE The AC socket must be firm and reliable Do not connect the portable air conditioner to a multiple socket outlet that is shared with other electrical appliances Insert the AC power plug securely into the AC socket before turning on the unit Press the 0 button and the unit will begin to run COOLING OPERATION 1 Ensure that the drain tank is properly placed in the unit 2 Repeatedly press button to choose the cooling mode LCD window will show COOL During the cooling operation always place the duct through an open wind
8. TM USA Instruction Manual Portable Air Conditioner HDD gt MUL ILE Sq lE i emm Model WA 9010E It is important that you read these instructions before using your portable air conditioner and we strongly recommend that you keep them in a safe place for future reference oales Inquiries 800 934 9194 TABLE OF CONTENTS Thank you and energy saving tips Rui eo UIC HO Wee Partsandaccessories Wetz CH rz 10 MT Control panelfunctions IxemotecofntrolTuncllons uetor e ens Operatingtheunit Wig Viri vll E d Ee E geift ee OU E SDECIICAN ON E Your Guarantee THANK Y AN Thank you for choosing the portable air conditioner from SPTusa a leading brand in indoor air treatment We would like you to enjoy the many benefits this unit offers so please take the time to read this manual carefully and take full advantage of the many advanced features that your SPTusa Air Conditioner offers you SPTusa has specialized in complete indoor environment control manufacturing world class air conditioners dehumidifiers and air purifiers with innovative technology In designing these advanced products we have listened carefully to our customers and have pa
9. dicator MODE Button Press this button will select among the modes of cooling dehumidify or fan ON OFF Button FULL To turn unit ON or OFF Louver indicator Timer set to turn ON Timer set to turn OFF Display of preset temperature and failure Display of Time Setting code When SET is displayed the displayed The displayed digits digits indicate the preset temperature When indicate the remaining FAULT is displayed the displayed digits time for timer ON OFF indicate the code of failures operation OPERATION AND FUNCTIONS OF REMOTE CONTROL Temperature setting button Sets the room temperature Each press of the A or V button the temperature setting is increased or decreased by 1 F FAN SPEED Button Choose high medium or low speed air delivery TIMER Button Sets the switch on or switch off time for Timer Used together with the HOUR button Time setting can be made within the range of 1 12 hours with an interval of one hour Time Setting buttons These buttons are used to set the clock or the time for timer switch on off k EEEE TA Display screen ON OFF Button Turns the unit ON or OFF 1171 F LI bn COOL DRY FAN ad RS e MODE selection SEM a button JH Art Press this button to select the among the modes cooling dehumidifying or fan Sa 1 SWING button Press this button
10. effect will reduce dehumidify performance 5 Dehumidify will work when ambient temperature is higher than 6 amp F and higher than set temperature 6 Dehumidify works in 10 minute cycles 6 minutes compressor on and 4 minutes off TIMER SETTING To set time to start the unit when power is off but with power supplied 1 Press 5 button the LCD window will show gt 9N 2 Press the TIME button and set the number of hours you wish to start running the unit For example if you wish to have the unit start in 8 hours press the TIME button repeatedly until 8 hours is indicated To set time to stop the unit when unit is running 1 Press gt button the LCD window will show 5 2 Press the TIME button to set the desired time to stop the unit For example if you wish to have the unit stop in 5 hours press the TIME button repeatedly until 5 hours is indicated NOTE The time range for timer on or off is between 1 12 hours AUTO SWING FUNCTION 1 Press button and LCD window will show E Louver will begin to swing automatically 2 Press 2 button again and in the LCD window will disappear swinging will stop LOCKING THE KEY PAD Press A and X7 buttons together and hold for more than two seconds will lock the keypad LCD window will show a Press the two buttons together again will unlock the keypad and the symbol ri will disappear Oma unhunn EK T i
11. l void the warranty AIR FILTER If the air filter is blocked by a lot of dust the air flow volume will reduce Clean the filter once every two weeks Opening the air filter 1 Open the air filter cover upwards and remove the air filter 2 Takdhe air filter out of filter cover Clean Wash the air filter by immersing it gently into warm about 40 104 F water with a neutral detergent Rinse the filter clean of detergent and dry it thoroughly in a shaded place Mounting 1 Attach the filter to filter cover with the attachment hooks on the inside surface of the cover 2 Match hooks at the bottom of the filter cover into the holes of the case push it back into its original position 421 filter cover hooks 6 KEEP SURFACE CLEAN Clean the surface of the unit with a damp cloth then dry with duster or similar WATER TANK 1 Hold the handle in water tank and draw out slowly 2 Pour out the water Clean with neutral detergent rinse clean and dry handle 1 STORAGE SEET d ii Ai LU LL Aan END OF SEASON OPERATION amp STORAGE 1 To remove drain water from the drain tank take out the plug from the plastic pipe shown in Fig 4 Then operate the unit in fan mode for half a day until the pipe is dry 2 Switch off the unit and disconnect the plug from the power supply 3 Tie the cable with a string 4 Wrap the machine with the plastic bag and store in a dry location plastic duct
12. ow to exhaust warm air from the room 3 Repeatedly press button to set desired room temperature between 63F 88 F 4 Press 5 button to choose a proper fan speed high medium or low 5 Press button to adjust the air delivery direction 5 symbol indicates swinging mode Press again to set fixed direction NOTE In order to improve the cooling efficiency please note the following a If your room is directly exposed to sun draw the curtains and blinds b Do not place unit near any heat source or under direct sunlight The compressor will start approximately 3 minutes after the unit is turned on and set to COOL function this will help prolong the life of the compressor After switching the unit off please wait at least 3 minutes before turning the unit back on d The cooling system will switch off if the room temperature is lower than set temperature The fan however keeps working at the set level When the ambient temperature rises above the set temperature 2 F cooling will resume DEHUMIDIFYING OPERATION 1 Keep the windows and the doors closed to aid in effectively dehumidifying the room 2 Ensure that the drain tank is properly placed in the unit 3 Repeatedly press 22 button to choose the dehumidifying mode LCD window will indicate DRY The fan speed is set on LOW and cannot be adjusted 4 When used as dehumidifier only do not use the air exhaust duct If the air exhaust duct is used air exchange
13. ssed their views on to our research and development laboratories We wish you many years of enjoyable use After reading this manual please keep it in a safe place for future reference Energy Saving Tips Please use the unit in the recommended room size Do not locate the air conditioner where furniture or other objects can obstruct the airflow Keep blinds curtains closed during the sunniest part of the day Close the fireplace damper and floor or wall grills so that cool air does not escape through the chimney or ductwork Keep the filters clean Set the unit to maximum cooling and high speed fan initially then adjust the unit to a comfortable setting NOTE It is recommended to turn on the air conditioner when the room temperature is around 75 F Do not wait until the room is excessively hot SETTLE RETTEN em TAH YD ETE oss INTRODUCTION SPTusa Portable Air Conditioner This Portable Air Conditioner is a small size appliance which can adjust the temperature and humidity in a room Its flexibility characteristics make it easily used on different occasions in different rooms It also has multiple functions including cooling dehumidifying and fan ventilation This unit is designed to be used in a family house office etc It has a compact design compared to others with the same cooling capacity Power consumption is low and the noise especially low ATTENTION Before you use your PORTABLE AIR
14. stat 62 F 88 F Net Weight TT 105 Dimensions 14 76 W 18 D x 32 68 H Working Temperature Cooling 50 F 95 F Dehumidifying 68 F 95 F REMARKS 1 The data may vary please refer to the rating label on the back of the unit 2 The above conditions are measures at Cooling Indoor RT 81 F RH 60 Uninsulated rooms such as sun rooms garages or attics should be less than 250 sq ft If this product is defective or not working properly Please DO NOT return to your retail store Please contact us directly with any Service or Technical Assistance Contact us toll free at 1 800 330 0388 Sales Inquiries 800 934 9194 YOUR GUARANTEE Loos Li Portable Air Conditioner If this product is found to be faulty as a result of faulty materials or workmanship within one year from date of purchase it will be repaired or replaced free of charge This guarantee is subject to the following terms SPTUSA must be notified of the fault Proof of purchase must be presented to SPTUSA s nominated representative The warranty will be void if the product is modified misused or repaired by an unauthorized person The guarantee after repair or replacement will not be extended beyond the original one year period All replacement parts or units will be new or reconditioned Parts or units which are replaced become the property of SPTUSA The warranty applies to the use of this product in the United States
15. xtended beyond the supplied hose The machine starts and stops frequently CAUTION It is normal Plug firmly into wall socket Change or reset the fuse Pour out water Place water tank correctly Change SET TIME Clear the inlet or outlet Move the heat source Clean the air filter Set suitable temperature Set suitable fan speed Close windows and door Place on a level surface Keep power within rating Keep exhaust hose as straight and short as possible Do not extend beyond supplied hose Unplug and stop running immediately in case of the following and contact SPTusA at 1 800 330 0388 1 The fuse and switch breaks often 2 The power cord get excessively hot or the sleeve of the cord is broken 3 Something seems abnormal Self diagnosis function This unit is equipped with a Self Diagnosis system When irregular performances are sensed the LCD panel will display the following fault codes Check code FAULT E8 FAULT E3 Diagnosis of malfunction Overheating protection Faulty coils Ambient temperature is not within the working temperature range 50 F 95 F FAULT E2 FAULT E4 Unit faults Action Wait until unit cools off Service required Wait for ambient temperature to fall within the working temperature range Service required SPECIFICATIONS Power Consumption Humidity Removal Capacity Recommended Room Size Compressor Refrigerant Timer 1 12 hours Thermo
Download Pdf Manuals
Related Search