GE 22.52 cu. ft. Side-By-Side Refrigerator with LightTouch Dispenser
Contents
1. In this case edges must be routed e Follow notes on drawing to assure room for fingers hands to open handles Door panel dimensions in inches ge com Order your own custom wood panels to match cabinetry or other decor Panels up to 1 4 thick will fit door frame with no special preparation Add filler behind material thinner than 1 4 for proper fit Weight Limits Total weight of panels i e both freezer panels Fresh Food 38 Ibs Freezer 28 Ibs Note Panels up to 3 4 will require special routing area around handles Dimensions may vary depending on depth of panel Collar trim installation An enclosure is required to match up to the trim see Typical Installation To obtain the most integrated look the cabinet or soffit above the refrigerator should extend out to the same depth as the side panels The refrigerator opening must have minimum dimensions of 70 1 4 high x 36 1 8 wide x 24 1 2 deep for 23 cu ft models and 72 1 4 high x 36 1 8 wide x 24 1 2 for 25 cu ft models as shown at right If there is an overhead cabinet allow 1 for cabinet door clearance with the top trim piece so the cabinet doors can be opened without hitting the top trim If 1 2 side panels are used then side trim and panel will be even If 3 4 side panels are used then some of the side panel will extend beyond the trim and m2. opening or the underside of the overhead cabinets 24 1 2 For Models with Trim Kit If frameless style cabinets are planned for above the refrigerator you may need to consider adding a maximum of 1 4 70 1 2 to height of opening for 23 cu ft models and 1 8 72 3 8 for 25 cu ft models to allow additional clearance between cabinet doors and top of refrigerator trim lt 36 1 8 gt when cabinet doors are in open position Water hook up on the refrigerator IMPORTANT Before finalizing specifications for your GE Profile CustomStyle Refrigerator please NOTE e A minimum width of 36 is required for A refrigerator installation e Be sure to allow for 1 2 or 3 4 side panels i in addition to the 36 minimum 24 o Rear Wall View Create a custom look for your GE Profile CustomStyle side by side refrigerator Still another advantage offered by GE Profile CustomStyle Refrigerators is ease of installation For a refrigerator that does so much to enhance the beauty of your kitchen the behind the scenes preparation and installation are surprisingly simple 1 2 to 3 4 Side Panel lt Route hand slot before installing panel Fabricating the enclosure e The drawing shows an 84 cabinet elevation Adjust dimensions accordingly for other cabinet elevations e Cabi
3. 1 4 72 1 4 are minimum and measured from the finished floor to top of opening or the underside of the overhead cabinets For Models with Trim Kit If frameless style cabinets are planned for above the refrigerator you may need to consider adding a maximum of 1 4 70 1 2 to height of opening for 23 cu ft models and 1 8 72 3 8 for 25 cu ft models to allow additional clearance between cabinet doors and top of refrigerator trim when cabinet doors are in open position ic 3 4 Cabinet Side Panel 1 2 Cabinet Side Panel Refrigerator Case Side Trim Side trim must be installed flush with the gasket contact surface on the case Door Gasket Cabinet Overhead Door Cabinet 1 Case Top Trim
4. GE Profile Arctica and GE CustomStyle side by side installation information amp specifications Rough in dimensions Standard new construction and replacement installation Installation tips to maximize the built in look e All wall floor molding should be removed prior to installation e Water recess on rear wall recommended to prevent water line damage 48 minimum length 1 4 diameter water line tubing recommended e When possible recess both copper water line and electrical outlet see local codes Front and rear leveling legs are adjustable for the built in look see owner s manual e If optional collar trim kit is to be used or anticipated see collar trim installation on next page for different rough in dimensions Installation of water outlets mie K Alternate water line location through floor Top View Allow 48 minimum water line to enable refrigerator to be pulled forward Recommended water line location using recess in rear wall Recommended single loop of 1 4 copper water line 8 Ceiling 12 Soffit 13 to 14 Water Electrical Cabinet oO O 3 4 Airspace 1 2 Gap 1 4 Wall Plates O O Counter l 70 1 4 23 cu ft models T 72 1 4 o 25 cu ft models o Oj O O O The rough in dimensions of 70 1 4 72 1 4 are minimum and measured from X the finished floor to top of
5. net pieces to order 2 side panels and 1 wall cabinet e Side panels will typically be attached to adjacent cabinets and or cleated to rear wall and floor e Refer to GE refrigerator installation instructions for proper plumbing and electrical and air clearances e 1 Some framed cabinet lines will make a refrigerator enclosure with a cabinet 12 high x 39 wide with sides and 1 1 2 face frame extended down to floor to create the refrigerator space This will replace the above construction 2 A tall cabinet on either side of the refrigerator can replace a side panel e Counter overhangs on either side of the refrigerator should have clipped corners to allow for full door swing e If the refrigerator has a wall returning beyond the front of the refrigerator on either side a 2 tall filler will help allow for movement of the door Door Panels e See drawings for exact dimensions of the fresh food and freezer door panels e Refrigerator door fronts from stock and most semi custom cabinet manufacturers will be supplied as 1 4 thick panels cut to dimensions with closest available standard door sizes applied to front This will leave a reveal at top bottom and sides Width of reveal will depend on manufacturer s standard door sizes Door will be affixed on the 1 4 panels at factory or in the field by the local supplier depending on manufacturer e Local shop built or custom cabinet supplier may fabricate custom 3 4 panels
6. ust be finished IMPORTANT Before finalizing specifications for your GE Profile CustomStyle Refrigerator please NOTE e A minimum width of 36 1 8 is required for refrigerator installation with collar ae sg N y Typical Installation A Shaded areas represent front surfaces of side panels and overhead cabinet or soffit that contacts trim Y 23 cu ft models 25 cu ft models Cut Cut Cut Cut out 1 8 out gt 1 8 1 8 gt lt out out 1 8 A A 5 16 5 16 5 16 14 15 32 gt 14 15 32 gt 17 7 8 17 x y 67 9 32 67 9 32 69 69 ry ry FRONT FRONT FRONT FRONT FRONT FRONT 4 14 15 32 gt 14 15 32 gt 19 15 32 gt 14 15 32 gt a 14 15 32 gt 19 15 32 33 5 8 36 1 4 AA y Y Al y Y Freezer panel Freezer panel Fresh food Freezer panel Freezer panel Fresh food without dispenser with dispenser panel without dispenser with dispenser panel Detail C Notch required at top corner 1 8 gt as noted 5 16 FFA lt Fresh Food panel shown 1 2 minimum J 70 1 4 23 cu ft models NY 172 174 25 cu ft models 24 1 2 Panels 1 4 thick or less y J 114 Max p lt 36 1 8 gt The rough in dimensions of 70
Download Pdf Manuals
Related Search