Hoover U5454-900 WindTunnel Vacuum
Contents
1. WindTunnel by HOOVER Congratulations on your purchase This WindTunnel vacuum cleaner takes HOOVERe Type Y Allergen Filtration filter bags This product was designed for easy Assembly See page 3 www hoover com D Owner s Manual ENGLISH gt pp 1 14 ESPA OL gt p g 15 21 FRAN AIS p 22 28 Review this manual before operating cleaner Fill in and retain The model and serial number are located on the bottom of the cleaner as shown For your personal records please enter the COMPLETE model and serial number in the spaces provided and retain this information Your cleaner is model and has serial number It is suggested that you attach your sales receipt to this owner s manual Verification of date of purchase may be required for warranty service of your HOOVER product Be sure to fill out and return the product registration card included with your cleaner Index Assembling Cleanet cs00sse 3 5 Carton Contents c ccccsssesssseeeeeeees 3 Cleaner DeSCcriptions s0e00 5 HOW TO USC ii 5 8 Embedded Dirt FINDER Feature 6 Cleaning TOols sssseeeeseeeees 7 8 If You Have a Problem 2 s000s00 13 Important Safeguards seee 2 L bricat N cious ericceereerietiezie ek 12 Maintenance Authorized ServiCe cscsssssseee 12 Cleaning Filters ccsecceeesseseees 9 Clearing Blockag2. 3 13 and remove any loose debris which aw eleanareuciion may have accumulated under it e Check items under Cleaner suction low If blockage occurs during powered hand tool use Clearing blockages Disconnect cleaner from electrical outlet Low suction or pick up may be due to a blockage in the system Refer to the fol lowing steps to check for blockages continuing with each step until the blockage is found 1 Check fullness of filter bag change if needed 1 Disconnect powered hand tool from hose Remove bottom plate belt guard and turbine as described in Figs 3 18 3 19 and 3 26 Remove any blockage from turbine channel D Replace belt turbine brush roll belt guard and bottom plate Checking airflow path 2 Plug cleaner in and turn ON Check for suction at end of hose A a If there is suction continue with step 3 b If there is no suction check for blockage in hose and dirt tube as follows 1 Disconnect hose from dirt duct C by reversing procedure for Attach hose on p 4 Figs 1 11 and 1 12 2 Clear out hose 3 Look into C and remove blockage 3 Check connection at hose tube B remove any blockage 42 Full One Year Warranty Domestic Use Your HOOVER appliance is warranted in normal household use in accordance with the Owner s Manual against original defects in material and workmanship for a period of one full year from date of purchase This war
3. Center or Authorized Hoover Warranty Service Dealer Depot by e checking the Yellow Pages under Vacuum Cleaners Household OR e checking the list of Factory Service Centers provided with this cleaner OR e calling 1 800 944 9200 for an auto mated referral of authorized service outlet locations U S only OR e checking the Service section of The Hoover Company on line at www hoover com Do not send your cleaner to The Hoover Company in North Canton for service this will only result in delay If further assistance is needed contact The Hoover Company Consumer Response Center North Canton Ohio 44270 Phone 1 330 499 9499 In Canada contact Hoover Canada Burlington Ontario L7R 4A8 Phone 1 800 263 6376 Always identify your cleaner by the complete model number when request ing information or ordering parts The model number appears on the bottom of the cleaner Hoover Cleaning Performance This Hoover Cleaning Performance System is for comparing the relative pro gressive performance of Hoover uprights only and not for comparison with any other brands The majority of this rating is based upon the American Society for Testing and Materials ASTM Carpet Cleaning Effectiveness Testing ASTM Test F608 Other performance factors include Hose Power ASTM Test F558 Surface Litter Cleaning Hard Floor Cleaning Edge Cleaning Air Filtration and Cleaning Width 4 If you have a problem If a
4. Company 101 East Maple St North Canton Ohio 44720 Phone 1 330 499 9499 In Canada contact Hoover Canada Burlington Ontario L7R 4A8 1 800 263 6376 14
5. To turn cleaner OFF push switch down Cord clip To help keep the cord out of the way while vacuuming position cord in cord clip A located at rear of cleaner on hose rack Transporting cleaner To move your cleaner from room to room put handle in upright position tilt cleaner back on rear wheels and push forward Embedded Dirt FINDER feature With red and green lights A the Dirt FINDER system alerts the user to areas of carpet that may need more cleaning attention It is able to sense when larger amounts of dirt particles especially embedded dirt are removed To let you know that the Dirt FINDER fea ture is ready the red light will come on Carpet height adjustment The cleaning of carpet and rugs takes place at the nozzle A When it is necessary to raise and lower the nozzle for various carpet pile heights slide the nozzle control knob B Ie the desired setting Carrying cleaner The cleaner can also be moved by using the carrying handle when the cleaner is first turned on After a few seconds the red light will go off and the green light will come on Cleaning may then begin The green light will remain on through out cleaning except when the detector senses that a larger amount of dirt is being picked up then the red light will come on When the red light is on you should take additional cleaning strokes in the area until it changes to green e The red
6. faces up Press the latches on either side of tool and remove bottom plate A 2 Unscrew the two Phillips screws and remove belt guard B 3 Remove agitator including end plates C and discard 4 Inspect belt to ensure that it is in good condition If belt is cracked gouged or broken replace it see following section 5 Insert brush roll through belt and posi tion belt over gear teeth D on brush roll 6 With curved ends down slide end plates C of brush roll into slots E on tool Continued 11 7 Replace belt guard B making sure not to pinch brush bristles in guard Turn agitator making sure it rotates freely Replace and tighten screws Powered hand tool Belt replacement Inspecting the belt The powered hand tool belt is designed to last a long time and is not normally replaced However if the belt is cracked gouged or broken it should be replaced The belt can be seen through the top of the nozzle or by removing the bottom plate and belt guard Figs 3 18 and 3 19 Lubrication The motor is equipped with bearings that contain sufficient lubrication for the life of the motor The addition of lubri cant could cause damage Therefore do not add lubricant to motor bear ings The agitator is equipped with two ball bearings that should be lubricated periodically by a Hoover Factory Service Center or an Authorized Hoover Warranty Service Dealer Depot 12 8 To replace bo
7. light may seldom come on dur ing cleaning This means that your cleaner is picking up primarily fine sur face dust and lint which the system may not detect or that the carpet is generally clean To increase the feature s sensi tivity to dirt set the switch B to the Hi position e At other times the red light may stay on for a considerable amount of time This Handle position For ease in sliding knob the handle should be in the upright position C The nozzle will not move into the adjusted position until the cleaner handle is lowered to the operating position D Handle positions The handle of your cleaner has three positions upright for storage and when using cleaning tools operating position for general operation on carpet and floors low for reaching under low furni ture Step on handle release lever to lower handle means that the carpet contains a high level of dirt which is being removed by the cleaner To decrease the feature s sensitivity to dirt set the switch to the Reg Regular position Settings For maximum cleaning performance the following carpet height settings are recommended e Lowest setting for all types of carpet Note If the cleaner is difficult to push slide knob to the next higher setting e Higher settings for very deep pile Carpet where easier pushing effort is desired while maintaining good cleaning performance Cleaning lightweight flexible
8. minor problem occurs it usually can be solved quite easily when the cause is found by using the checklist below Problem Cleaner won t run Possible Cause Possible Solution Not firmly plugged in Plug unit in firmly e No voltage in wall plug e Check fuse or breaker Blown fuse or tripped breaker e Replace fuse or reset breaker Thermal protector activated e Allow cleaner to cool for 30 minutes this will reset the thermal protector Problem Cleaner tools won t pick up Possible Cause Possible Solution Broken or worn belt e Replace belt e Agitator brush roll worn e Replace brush roll e Filter bag full e Change filter bag e Incorrect carpet height setting e Move nozzle control knob to lower setting e Blockage in air flow passage e Clear blockage Problem Cleaner hard to push Possible Cause Possible Solution Incorrect carpet height setting e Move carpet height control to a higher setting Problem Powered hand tool brush roll won t run Possible Cause Possible Solution e Too much pressure being applied to Checking under bottom plate 4 Turn cleaner OFF and unplug tool e Continue using tool applying light 5 Remove bottom plate belt and agita pressure tor see The belt section e Blockage in turbine channel Look into opening D for blockages and e Remove blockage remove e Broken or worn belt e Replace belt 6 Remove agitator shield see Fig
9. rugs Stand on one end of rug and move cleaner toward other end or edge Before reaching edge push down on handle This will lift up the nozzle front of cleaner as shown and will prevent rug from clinging to cleaner Continue to lift up nozzle so that when you have reached the edge it is completely off the rug Move cleaner back to start again lower nozzle and use only forward strokes How to attach tool cover The tool cover is designed with a break away feature which allows it to snap free if it is pushed open too far To reattach align hinges of cover with slots on sides of tool storage area Push cover down to secure in place Edge cleaning Special edge groomers are provided on both sides of the nozzle to remove dirt in carpet near baseboards and furniture Guide either side of nozzle parallel to edge of carpet or furniture Cleaning tools Tools allow for cleaning surfaces above the floor and for reaching hard to clean areas The cleaner is ready for tool use when handle is in upright position CAUTION Agitator continues to rotate while cleaner handle is in upright position Avoid tipping clean er or setting it on furniture fringed area rugs or carpeted stairs during tool use Stair cleaning A stair cleaning handle has been de signed for ease in using your cleaner on stairs With handle in operating position place fingers under edge of stair clean ing handle and guide cleaner with
10. dle slots C on handle section Continued gt 3 Remove bag door on cleaner body by pushing down at top of door and pulling door outward Switch A above bag door should be in OFF position While holding rack in place slide Push bolts into holes on back of handle onto cleaner body handle Make sure tab is inserted fully into slot Place nuts in recessed areas on front of handle Hold each nut in place while tightening each bolt securely with a Phillips screw driver STEP II Attach hose A A Align end of hose with projections A over slots B in dirt duct Reposition bag door by fitting tabs Press cord into the 3 notches and on bottom of door into opening the clip as shown Press top of door to snap securely shut NOTE Hose must be connected as shown for all operations Slide hose into B and twist hose to Position hose over rack and into lock it into place hose tube D or E depening on Lift hose tube cover C your model STEP III Position tools Insert ends of dusting brush A crevice Remove switch lock A above ON OFF tool B into storage areas Secure furni switch B by pulling it straight out Place smaller unridged end of wand into ture nozzle C in clip Dispose of switch lock bottom of rack Snap wand into clip Close tool cover If switch lock has come off during Repeat with other wand assembly make sure switch is in OFF Open tool cover position down befor
11. e plugging cord into electrical outlet Cleaner description The assembled cleaner will 15 Furniture guard helps look like the drawing prevent cleaner from mark 1 Handle ing furniture 2 ON OFF switch 16 Nozzle control knob slide 3 Cord hooks wrap cord knob to correct setting for around hooks for storage height of carpet being The top hook can be cleaned rotated right or left for 17 Headlight easy cord release 18 Embedded Dirt FIND 4 Hose ERIM 5 Tool cover sensitivity switch 6 Dusting brush 19 Dirt FINDER display 7 Furniture nozzle 20 Check bag indicator 8 Crevice tool 21 Stair cleaning handle 9 Powered hand tool located below lower edge 10 Carrying handle of door 11 Wands 22 Bag door 12 Final filter door 23 Cord clip 13 Handle release lever 24 Hose rack step on lever to lower handle to operating or low positions 14 Edge groomers Operate cleaner only at volt age specified on data plate on bottom of cleaner This cleaner is intended fo r household use ON OFF switch Polarized plug Plug cord into electrical outlet To reduce the risk of electric shock this To turn cleaner ON push switch up appliance has a polarized plug one blade is wider than the other This plug will fit in a polarized outlet only one way If the plug does not fit fully in the outlet reverse the plug If it still does not fit contact a qualified electrician to install the proper outlet Do not change the
12. edge groomers ask for HOOVER part No 39511004 How to replace Disconnect cleaner from electrical outlet Remove bottom plate as described in The belt section Fig 3 10 The agitator brush roll When to replace When agitator brushes are worn the agitator should be replaced To check condition of brushes discon nect cleaner from electrical outlet Move edge of acard across bottom plate while turning agitator To maintain cleaning effectiveness replace agitator if brushes do not touch card What to buy Your cleaner requires either a 13 or 15 agitator When purchasing a new agita tor ask for one of the following 13 HOOVER part No 48414110 15 HOOVER part No 48414115 Installing groomers Lift off both old edge groomers and slide new edge groomers into position as shown Reposition bottom plate and secure with 4 Phillips head screws How to replace Disconnect cleaner from electrical outlet Remove bottom plate belt and agitator following directions in The belt section beginning with Fig 3 10 Discard old agitator Continue following the directions in The belt section to reposition belt new agi tator and bottom plate Powered hand tool Agitator brush roll replacement When agitator brush roll brushes are worn the brush roll should be replaced Ask for HOOVER part No 48414088 How to replace 1 Remove tool from hose and turn it so bottom
13. er Company on line at www hoover com What to buy To assure cleaning effectiveness use only Genuine HOOVER Allergen Filtration Type Y disposable filter bags It is imperative that you use only gen uine HOOVER filter bags made by The Hoover Company to assure that your cleaner operates at peak performance HOOVER bags can be identified by these trademarks a Check bag indicator The indicator J will begin to show red as the filter bag fills with dirt There are three conditions that will cause the indicator to become completely red 1 If the bag is full change the bag 2 If very fine materials have been picked up Clogging the bag pores change the bag 3 If there is a blockage at the front of the cleaner in the hose tools or at the bag opening remove the blockage see Clearing blockages section Changing filter bag Disconnect cleaner from electrical outlet Removing bag door To change filter bag press down at top of bag door and pull door forward Remove door Removing and installing filter bag Grasp filter bag collar A and pull collar from tube B Note Do not clean out old filter bag and reuse Discard used filter bag Hold new filter bag as shown Align open ing in filter bag with B Push A firmly onto B Tuck in filter bag Cleaning final filter The final filter assists in the filtration process to return clean air to the room To
14. es ssss1e 13 Replacing Agitator Brush Roll 11 Replacing Powered Hand Tool Agitator Brush Roll 0000 11 Replacing Belt ccsssscssseeeees 10 11 Replacing Powered Hand Tool Belt12 Replacing Edge Groomers 11 Replacing Headlight 000 10 Replacing Filter Bag scc0s0 8 9 Thermal Protector ccccsssseeesesseeees 12 Warranty asa tanuri niaranra cain aaa 14 UL GPe 1997 The Hoover Company www hoover com move U5465 900 senes M 12 120 V 60 Hz 12 0A BAG TYPE YE BELT 38528 033 H ser no XXXXXXXXAXXXA LISTED 263G HOOVER cO FOR HOUSEHOLD USE ONLY S PARA USO HOGARE O SOLAMENTE POUR UN USAGE M NAGER UNIQUEMENT NRTUC a Hoover Co N Canton Ohio 44720 LR 100862 Th Made in U S A Hecho en E U A Fabrique aux U Important Safeguards When using an electrical appliance a Iw ays fo ow basic precautions i n cluding the following READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE a r nN Nn g To reduce the risk of fire electric shock or injury Do not use outdoors or on wet surfaces Close supervision is necessary when any appliance is used by or near children Do not allow vacuum cleaner to be used as a toy or to run unattended at any time Keep hair looseclothing fingers feet and all parts of body aw ay from openings rotating agitator and other moving part s Do not operate cleaner in bare fee
15. ey B 10 Installing bulb Pull old bulb straight out of socket Push new bulb straight into socket until locked in place Excessive force is not required How to replace Disconnect cleaner from electrical outlet Removing bottom plate Place handle in low position and turn cleaner over so bottom side is up Remove the 4 screws as shown with a Phillips screw driver Lift off bottom plate A Replacing agitator brush roll Insert agitator through belt and place belt in belt guide C on agitator Should the agitator shield D become dislodged while replacing the belt or the agitator reposition it as shown noting the placement of its belt guide E Replacing lens Reposition lens and secure with the two Screws Removing belt Remove agitator brush roll and used belt Discard used belt Securing agitator Grasp agitator firmly and fit it into posi tion by first sliding end opposite the belt into the rectangular slot F on side of cleaner Pull other side of agitator G into place Turn agitator making sure belt is not pinched between agitator and agitator shield Replacing bottom plate Reposition bottom plate and 4 Phillips head screws Tighten screws securely The edge groomers When to replace The edge groomers located on both sides of the nozzle should be replaced when they no longer extend past the surface of the bottom plate What to buy When purchasing
16. g from time to time It is recommended that you change the filter bag when dirt reaches the dotted line If more dirt than this accumulates your cleaner will not operate effectively Note All new carpet has loose fibers which can fill the bag quickly while vacuuming If you are using the cleaner on new carpet be sure to change the filter bag often CAUTION Very fine materials such as face powder cornstarch fireplace ashes or fireplace soot may seal the filter bag and may cause it to burst even though it is only partially full of dirt When cleaner is used to remove material of this nature change filter bag often Select proper tool E Dusting brush may be used for carved furniture table tops books lamps lighting fixtures venetian blinds baseboards shutters and registers F Furniture nozzle may be used for upholstered furniture draperies mat tresses clothing automobile interiors and carpeted stairs G Crevice tool may be used in tight spaces corners and along edges in such places as dresser drawers uphol stered furniture stairs and baseboards H Wands are used to give extra length to your hose Use them with any of the above tools I Powered hand tool may be used for upholstered furniture carpeted stairs and hard to reach places Where to buy Filter bags may be purchased from your Authorized Hoover Dealer Depot Leading Retailers Hoover Factory Service Centers or through The Hoov
17. nter or Auth o ri zed Hoover Warranty Service Dealer Depot Use vacuum cleaner only for its intended use as described in the instructions Use only attachments recommended by The Hoover Company o t h e rs may cause hazards Save these instructions 1 Assembling cleaner This cleaner was inspected and packaged carefully before being shipped from the factory If you should happen to need assistance during assembly or operation call 1 800 944 9200 for an automated referral of authorized service outlet locations U S only OR 1 330 499 9499 to speak with a representative in our Consumer Response Center OR Visit us online at www hoover com to find the service outlet nearest you click on the Service button Carton contents Remove all parts from carton and identify each item shown Make sure all parts are located before disposing of packing A Handle section B Cleaner body C Hose rack D Hose cleaning tools and wands E Handle bolts and nuts packet in bag with owner s manual F Powered hand tool Note The white switch lock above the ON OFF switch aids in the assembly of your cleaner Assembly can be continued if the switch lock is missing However do not remove the switch lock until assembly is completed STEP 1 Attach rack and handle ia Open tool cover on handle section Attach hose rack to handle section Align hole on rack with circular tab A by fitting hooks B on rack over on han
18. other hand on upper handle As an alternative you may use the hose and powered hand tool or furniture noz zle for stair cleaning Clean from bottom to top When using cleaning tools the agita tor will continue to rotate CAUTION To avoid personal injury or unnecessary wear to carpet and to prevent the cleaner from falling always place it at bottom of stairs Removing hose When using cleaning tools cleaner handle should be in the upright posi tion Also turn cleaner OFF before disconnecting and connecting hose to hose tube A To use hose lift hose end as shown Lower cover B onto hose tube When you are finished cleaning with the tools be sure to lift cover from hose tube and reposition hose end into tube Continued 7 Attach wand and tools Attach tool or wand to the hose C Attach second wand or tool to wand D by pushing it firmly onto the wand Twist wand or tool slightly to tighten or loosen the connection How to clean tools To clean the hose and powered hand tool wipe off dirt with a cloth dampened ina mild detergent Rinse with a damp cloth Do not submerge the powered hand tool in water Cleaning tools may be washed in warm water with a detergent Rinse and air dry before using Familiarize yourself with these home maintenance tasks as proper use and care of your cleaner will ensure contin ued cleaning effectiveness Filter bag When to replace Check filter ba
19. r shield each time you clean the filters Removing debris under the shield will help maintain your cleaner s excellent pick up and suction Remove debris as follows 1 Disconnect cleaner from electrical outlet 2 Check for dirt accumulation by removing bottom plate Fig 3 10 removing agitator Fig 3 11 and lifting agitator shield Fig 3 13 3 Remove any debris and replace shield agitator and bottom plate Figs 3 13 to 3 15 Headlight replacement What to buy This cleaner uses a 12 volt wedge base type 912 bulb Hoover part No27313101 Removing lens Disconnect cleaner from electrical outlet Using a screwdriver remove the two screws as shown and lift off lens Belt replacement The belt on your Hoover cleaner causes the agitator to rotate and is important for the effective operation of the cleaner The belt is located under the bottom plate of the cleaner and should be checked from time to time to be sure it is in good condition When to replace Disconnect cleaner from electrical outlet To check belt remove bottom plate as shown in How to replace Replace belt if it is stretched cut or broken What to buy To assure effective operation use only genuine HOOVER belts with your clean er When purchasing a new belt ask for HOOVER part No 38528033 Installing new belt With lettering on outside of belt and positioned as shown in box on D slide new belt over motor pull
20. ranty provides at no cost to you all labor and parts to place this appliance in correct operating con dition during the warranted period This warranty applies when the appliance is purchased in the United States including its territories and possessions or in Canada or from a U S Military Exchange Appliances purchased else where are covered by a limited one year warranty which covers the cost of parts only This warranty does not apply if the appliance is used in a commercial or rental application Warranty service can only be obtained by presenting the appliance to one of the following authorized warranty service outlets Proof of purchase will be required before service is rendered 1 Hoover Factory Service Centers 2 Hoover Authorized Warranty Service Dealers Depots For an automated referral of autho rized service outlets in the U S A phone 1 800 944 9200 OR visit The Hoover Company on line at www hoover com This warranty does not cover pick up delivery or house calls however if you mail your appliance to a Hoover Factory Service Center for warranty service transportation will be paid one way While this warranty gives you specific legal rights you may also have other rights which vary from state to state If further assistance is needed or if there are questions concerning this war ranty or the availability of warranty ser vice outlets write or phone the Consumer Response Center The Hoover
21. remove this filter when it becomes dirty open the door on the side of the cleaner Lift out filter B and hand wash it in cold water with mild detergent Let filter air dry and reposition it on the side of the cleaner Make sure the green colored side of filter faces outward Close door Should you want to replace this filter ask for HOOVER part No 40110004 Do not operate cleaner without either the secondary or final filter in place Replacing bag door Reposition bag door by placing tabs on bottom of door into opening C Press top of door to snap securely shut Reattaching filter door The filter door is designed with a break away feature which allows it to snap free if it is pushed open too far To reattach align hinges C of cover with slots on sides of filter area Press door back into place Secondary and final filters Cleaning secondary filter Disconnect cleaner from electrical outlet The secondary filter A located behind the grill in the bottom of bag compart ment protects the motor from dirt parti cles If filter becomes dirty pull off grill and lift out filter Hand wash filter in cold water with mild detergent then air dry Reposition dry filter and grill Should you want to replace this filter ask for HOOVER part No 38765019 Check agitator shield Because your cleaner picks up so well we strongly recommend you check for debris accumulation under the agitato
22. t or when wearing open toe shoes or sandals Do not pick up anything that is burning or smoking suchas cigarettesm atches or hot ashes Do not use to pick up flammable or combu s t i ble materials such as gasoline or fine wood sandings or use in areas where they may be present Avoid picking up hard sharp objects with the cle aner T h ey may damage the cleaner and the bag A Iw ays turn off this appliance before connecting or disconnecting hose Do not use without dust bag or filters in place Change bag frequently when p i cking up very fine materials such as pow d er Use extra care when cleaning on stairs Do not put any object into openings Do not use with any opening bl o ck e d keep free of dust lin t h a i r or anything that may reduce air flow Do not pull or carry by cord use cord as a handle close door on cord or pull c ord around sharp edges or corners Do not run appliance over cord Keep cord aw ay from heated surfaces A Iw ays disconnect cord from electrical outlet before servicing the cleaner e Unplug cleaner when not in use Turn off all controls before unplugging Do not unplug by pulling on cord To unplug grasp the plug not the cord Never handle plug or appliance with wet hands The use of an extension cord is not recommended Do not use with damaged cord or plug If appliance is not working as it should has been dropped damaged left outdoors or dropped into water take it to a H o over Facto ry Service Ce
23. ttom plate A insert the four tabs on edge of bottom plate into slots on front of tool Pivot bottom plate down and snap closed Replacing belt When replacing belt ask for HOOVER part No 38528037 1 Remove bottom plate belt guard and brush roll as described in Figs 3 18 through 3 20 2 Grasp turbine E and pull firmly to remove 3 Remove belt from turbine pulley F Replace with new belt Thermal protector An internal thermal protector has been designed into your cleaner to protect it from overheating When the thermal protector activates the cleaner will stop running If this hap pens proceed as follows 1 Turn the cleaner OFF and disconnect it from the electrical outlet 2 Check secondary and final filters for dirt accumulation 3 Refer to Clearing blockages section 4 When cleaner is unplugged and the motor cools for 30 minutes the thermal protector automatically resets and clean ing may continue If the thermal protector continues to acti vate after following the above steps your cleaner may need servicing see Service section 4 With flat sides of turbine retainers G pointing down slide retainers into grooves H in tool housing and snap into place 5 Replace brush roll belt guard and bottom plate as described in Figs 3 20 through 3 23 Service To obtain approved HOOVER service and genuine HOOVER parts locate the near est Hoover Factory Service
Download Pdf Manuals
Related Search