LG LRDN20724ST Bottom Freezer Refrigerator
Contents
1. Use this section to become more familiar with the parts and features NOTE This guide covers several different models The refrigerator you have purchased may have some or all of the items listed below The locations of the features shown below may not match your model Q Digital Sensor Control B Refrigerator Light O Shelves O snack Pan Optibin Crisper Keeps fruits and vegetable fresh and crisp Q Ice Trays Ice Bin Q wire Durabase 11 Dairy Bin O Design A Door wire Freezer Shelf Refrigerator Door Rack O Freezer Light Q Freezer Door Rack REFRIGERATOR INSTALLATION 44 WARNING Excessive Weight Hazard Use two or more people to move and install refrigerator Failure to do so can result in back or other injury UNPACKING YOUR REFRIGERATOR Remove tape and any temporary labels from your refrigerator before using Do not remove any warning type labels the model and serial number label or the TechSheet that is attached to back wall of the refrigerator To remove any remaining tape or glue rub the area briskly with your thumb Tape or glue residue can also be easily removed by rubbing a small amount of liquid dish soap over the adhesive with your fingers Wipe with warm water and dry Do not use sharp instruments rubbing alcohol flammable fluids or abrasive cleaners to remove tape or glue These products can damage the surface of your refrigerator For more information see the Import2. BOTTOM FREEZER REFRIGERATOR User s Guide Please read this guide thoroughly before operating and keep it handy for reference at all times Models LRDN2272 LRDN2072 LRBN2251 LRBN2051 LRBC2254 LRBC2054 LRBC2252 LRDC2273 LRDC2073 LRBN2252 LRBN2052 LRDC2274 LRDN2271 LRDN2273 LRDN2073 P No 3828JL8019E TABLE OF CONTENTS English Version 2 Door Racks 25 French Version 40 Design A Door 25 Spanish Version 74 Dairy Bin 26 Warranty U S A 3 4 Freezer Wire Door Racks 26 Warranty CANADA 5 6 Ice Bin 26 Safety Instructions 7 8 DuraBase 26 Grounding Requirements 8 od a Drawer Tray 27 Parts and Features 9 11 Tilting Door 27 Refrigerator Installation 12 22 Pull out Drawer Basket 27 Unpacking Your Refrigerator 12 Can Dispenser 28 Installation 12 Triple Twist Ice Tray 28 Base Grille 12 Freezer Shelf 28 Removing Reversing and Replacing Filter 29 Your Refrigerator Doors 13 19 Care and Cleaning 30 31 Pull out Drawer 15 General Cleaning Tips 30 Door Closing and Alignment 19 Outside 30 Using Your Refrigerator 20 29 Inside Walls 30 Ensuring Proper Air Circulation 20 Door Liner and Gaskets 30 Multi Flow 20 Plastic Parts 30 Setting the Controls 20 21 Condenser Coils 30 Adjusting Control Settings 21 Light Bulb Replacement 30 31 Food Storage Guide 22 Power Interruptions 31 Storing Frozen Food 22 When you go on vacation 31 Refrigerator Shelves 23 About the Custom Cube Icemaker
3. resulting from drilling the hole in the pipe Take care not to allow water to drain into the drill Failure to drill a 1 4 hole may result in reduced ice production or smaller cubes 33 CONNECTING THE WATER LINE INSTALLATION INSTRUCTIONS CONTINUED 4 FASTEN THE SHUTOFF VALVE Fasten the shutoff valve to the cold water pipe with the pipe clamp Saddle Type _A Shutoff Valve Vertical Cold Water Pipe NOTE Commonwealth of Massachusetts Plumbing Codes 248CMR shall be adhered to Saddle valves are illegal and use is not permitted in Massachusetts Consult with your licensed plumber 5 TIGHTEN THE PIPE CLAMP Tighten the clamp screws until the sealing washer begins to swell NOTE Do not overtighten or you may crush the tubing Washer yo End Pipe Clamp Clamp Screw 6 ROUTE THE TUBING Route the tubing between the cold water line and the refrigerator Route the tubing through a hole drilled in the wall or floor behind the refrigerator or adjacent base cabinet as close to the wall as possible NOTE Be sure there is sufficient extra tubing about 8 feet coiled into 3 turns of about 10 diameter to allow the refrigerator to move out from the wall after installation 34 Saddle Type Shutoff Valve 7 CONNECT THE TUBING TO THE VALVE Place the compression nut and ferrule sleeve for copper tubing onto the end of the tubing and connect it to the shutoff valve Make sure t
4. 2 Damage to the product caused by accident vermin fire flood alteration misues abuse improper installation or acts of God 3 Commercialuse or use for other than the intended purpose Therefore these costs are the responsibilityof the consumer CUSTOMER ASSISTANCE NUMBERS To Prove Warranty Coverage Retain your Sales Receipt to prove date of purchase Acopy of your Sales Receipt must be submitted at the time warranty service is provided To Obtain Product Customer or Call 1 888 542 2623 1 888 LG CANADAJand choose the Service Assistance by phone appropriateprompt or by Internet http wwwlg ca To Obtain Nearest Authorized Call1 888 542 2623 1 888 LG CANADA and choose the Service Center Parts Distributor appropriateprompt Please have your producttype or Sales Dealer by phone refrigerator and ZIP Code ready or by Internet http wwwlg ca IMPORTANT SAFETY INSTRUCTIONS SAFETY MESSAGES This guide contains many important safety messages Always read and obey all safety messages A This is the safety alert symbol It alerts you to safety messages that inform you of hazards that can kill or hurt you or others or cause damage to the product All safety messages will be preceded by the safety alert symbol and the hazard signal word DANGER WARNING CAUTION These words mean You can be killed or seriously injured if you don t follow instructions A WARNING Aa tea Indicates an imminently ha
5. ce produit LA DUR DE TOUTE GARANTIE IMPLICITE INCLUANT LA GARANTIE IMPLICITE DE COMMERCIALISATION EST LIMIT LA DUR E DE LA GARANTIE EXPRESSE LG ELECTRONICS NE POURRA TRE TENUE RESPONSABLE POUR TOUTE PERTE OU UTILISATION DE CE PRODUIT INCONVENIENT PERTE OU TOUT AUTRE DOMMAGE INDIRECT OU ACCESSOIRE SURVENANT DE L UTILISATION OU DE L INHABILIT UTILISER CE PRODUIT OU POUR TOUT BRIS DE GARANTIE EXPRESSE OU IMPLICITE INCLUANT LA GARANTIE IMPLICITE DE COMMERCIALISATION APPLICABLE CE PRODUIT Certains tats ne permettent pas l exclusion ou la limitation de dommages accessoires ou indirects ou les limitations sur la dur e d une garantie implicite par cons quent ces limitations ou exclusions peuvent ne pas s appliquer Cette garantie donne des droits l gaux et l on peut en avoir d autres qui varient d un tat un autre ou d une province une autre LA GARANTIE CI DESSUS NE S APPLIQU PAS 1 Les d placements de service domicile pour la livraison ou la cueillette l installation le remplacement de fusibles ou de c blage r sidentiel appropri plomberie ou correction de r parations non autoris es 2 Dommage au produit caus par accident parasites incendie inondation ou actes de Dieu 3 R parations lorsque le produit LG est utilis d autres fins qu une utilisation domestique unifamiliale normale 4 Dommage r sultant d accidents de modifications de mauvaise utilisation d abus ou d une installati
6. equalize then see if it opens more easily TROUBLESHOOTING GUIDE AUTOMATIC ICEMAKER DOES NOT WORK Check if Then Icemaker power switch in the O off position Move the switch to the I on position Water supply turned off or not connected See the Connecting the Water Line section Freezer compartment too warm Wait 24 hours for the freezer to reach its ideal temperature Piled up cubes in the storage bin cause the icemaker Level cubes by hand to shut off TEMPERATURE IS TOO WARM OR THERE IS INTERIOR MOISTURE BUILDUP Check if Then The air vents are blocked Cold air circulates Locate air vents by using your hand to sense airflow and from the freezer to the fresh food section and move all packages that block vents and restrict airflow Refer back again through air vents in the wall dividing to multi flow Section for the location of the two sections air vents The doors are opened often When the door is opened warm humid air is allowed into the refrigerator The more the door is opened the faster the humidity builds up and the more warm air the refrigerator must cool In order to keep the refrigerator cool try to get everything you need out of the refrigerator at once keep food organized so it is easy to find and close the door as soon as the food is removed The control is not set correctly for the surrounding Refer to the Setting the Controls Section conditions Wait 24 hours for temperatures to stabili
7. opening type 1 Removing Refrigerator Door Remove the top hinge cover 1 Remove the 3 screws and lift off the top hinge 2 Lift the Refrigerator door 3 slightly and remove it Pry off the cover 4 using a slotted screwdriver and attach it on the right e Loosen the screw 5 remove the stoppers 6 and attach them on the left on the opposite side e Loosen the pin 8 and remove it Loosen the 2 screws 9 and the 2 screws 10 and lift off the middle hinge 11 Pry off the cover 7 using a slotted screwdriver and attach it on the right 2 Removing Refrigerator Handle e Remove the cap 1 by using a slotted screwdriver e Loosen the 4 screws 2 take off the handle 3 and install it on the right e Turn the handle upside down and assemble it in the opposite side of the refrigerator door 4 Attach the removed the cap 1 on the left 13 REFRIGERATOR INSTALLATION 3 Installing Refrigerator Door e Install the middle hinge 1 on the opposite side with the screws 2 and the screws 3 e Install the door 4 so that it fits onto the middle hinge pin 5 e Install the top hinge 6 with screws Reinstall top hinge cover 7 4 After Completing the Job Make sure that the four corners of the door gasket are not folded over To ensure a good seal apply a small amount of silicon grease on the gasket 14 REFRIGERATOR IN
8. Code ready To obtain the nearest Call 1 877 714 7486 Authorized Service Center 24 hrs a day 7 days per week 365 days per year Press the appropriate option and have your product type Refrigerator model number serial number and ZIP Postal Code ready Visite nuestro sitio web http www lgservice com LG Electronics GARANT A LIMITADA Estados Unidos de Am rica LG Electronics reparar o en su defecto reemplazar sin cargo el producto defectuoso en material o mano de obra bajo uso normal durante el periodo de garant a que se menciona a continuaci n desde la fecha original de compra Esta garant a es v lida solo para el comprador original del producto durante el periodo de garant a mientras permanezca en los E E U U Incluyendo Alaska Hawaii y otros territorios de E E U U Per odo de Garant a del refrigerador Congelador LG Producto Partes Mano de Obra Refrigerador Cmgelador la o 1a o Servicio a domicilio ExceptoModelo GR 051 Sistema Sellado 7 a os 1a o Servicioa domicilio ExceptoModelo GR 051 Compresor Condensador Evaporador No se aplicar otro tipo de garant a a este producto LA DURACION DE OTRAS GARANTIAS INCLUYENDO LA DE COMPRA ESTAN LIMITADAS A LA DURACION DE ESTA GARANTIA LG ELECTRONICS NO SE HACE RESPONSABLE POR LA PERDIDA EN EL USO DEL PRODUCTO POR INCONVENIENCIA O CUALQUIER OTRO DA O DIRECTO O CONSECUENTE QUE PROVENGA DEL USO Y O NO USO DE ESTE PRODUCTO O POR ALGUNA VIOLACION A LAS
9. Remove a layer of adhesive and backing to expose new adhesive e Install the plug buttons 4 on left side e Install the handle mounting screw 3 on the right side e Hold the handle so the masking tape is at the bottom Align keyhole slots 2 on the top and bottom of the back of the handle with the screws 3 mounted on the front of the door e Press the handle against the door front making sure that the screws 3 go into the keyhole slots 2 e Grasping the handle with both hands press it firmly against the front of the door and slide the handle down 6 This may require some force 17 Screws mounted on door Keyhole slots on back of handle Screws mounted on door REFRIGERATOR INSTALLATION 4 Removing Freezer Handle NOTE Before start check handle type in your model Handle Type 1 e Remove the cap 1 and the 2 caps 2 using a slotted screwdriver e Loosen the 2 screws 3 take off the handle 4 and install it on the right e Attach the caps you removed earlier figures 1 and 2 Handle Type 2 For this handle type is not neccesary remove it 5 Installing Freezer Door Install the base grille 1 e Install the door 3 onto the bottom hinge pin e Install the middle hinge 4 on the opposite side with the screw 5 and the screws 9 6 Installing Refrigerator Door ePlace the washer 6 on the middle hinge pin 7 e Install the door 8 so that it fits
10. as long as it is in any Canadian Province WARRANTY PERIOD MODEL LABOR 2 Years PARTS 2 Years SERIALNUMBER SEALED SYSTEM 5 Years Compressor condenser and evaporator HOW SERVICE IS HANDLED Call 1 888 542 2623 1 888 LG CANADA and choose the appropriate prompt Please have producttype refrigerator and ZIP Code ready See our website at http wwwlg ca This warranty provides in home service No other express warranty is applicableto this product THE DURATION OF ANY IMPLIED WARRANTIES INCLUDINGTHE IMPLIED WARRANTY OF MERCHANTABILITY IS LIMITED TO THE DURATION OF THE EXPRESS WARRANTY HEREIN LG ELECTRONICSUSA INC SHALL NOT BE LIABLE FOR THE LOSS OF THE USE OF THE PRODUCT INCONVIENCE LOSS OR ANY OTHER DAMAGES DIRECTOR CONSEQUENTIAL ARISING OUT OF THE USE OF OR INABILITYTO USE THIS PRODUCT OR FOR ANY BREACH OF ANY EXPRESS OR IMPLIED WARRANTY INCLUDINGTHE IMPLIED WARRANTY OF MERCHANTABILITY APPLICABLETO THIS PRODUCT Some provinces do not allow the exclusion or limitationof incidental or consequentialdamages or limitations on how long an implied warranty lasts so these limitations or exclusionsmay not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from province to province THE ABOVE WARRANTY DOES NOT APPLY TO 1 Servicetrips to your home to deliver and pickup install instruct or replace house fuses or correct wiring plumbing or correctionof unauthorizedrepairs
11. automatically However clean both sections about once a month to prevent odors Wipe up spills immediately GENERAL CLEANING TIPS Unplug refrigerator or disconnect power Remove all removable parts such as shelves crispers etc Use a clean sponge or soft cloth and a mild detergent in warm water Do not use abrasive or harsh cleaners Hand wash rinse and dry all surfaces thoroughly Plug in refrigerator or reconnect power OUTSIDE Waxing external painted metal surfaces helps provide rust protection Do not wax plastic parts Wax painted metal surfaces at least twice a year using appliance wax or auto paste wax Apply wax with a clean soft cloth For products with a stainless steel exterior use a clean sponge or soft cloth and a mild detergent in warm water Do not use abrasive or harsh cleaners Dry thoroughly with a soft cloth INSIDE WALLS allow freezer to warm up so cloth won t stick To help remove odors you can wash the inside of the refrigerator with a mixture of baking soda and warm water Mix 2 tablespoons baking soda to 1 quart of water 26 g soda to 1 liter water Be sure the baking soda is completely dissolved so does it not scratch the surfaces of the refrigerator DOOR LINERS AND GASKETS Do not use cleaning waxes concentrated detergents bleaches or cleaners containing petroleum plastic parts 30 PLASTIC PARTS covers and panels Do not use paper towels window sprays abra
12. cold air flow from the freezer to the refrigerator Setting the freezer control to a lower temperature keeps more cold air in the Freezer compartment to make it colder If you need to adjust temperatures in the refrigerator or freezer start by adjusting the refrigerator first Wait 24 hours after the refrigerator adjustment to check the freezer temperature If it is too warm or too cold then adjust the freezer control as well Use the settings listed in the chart below as a guide Always remember to wait at least 24 hours between adjustments RECOMMENDED CONDITION REASON ADJUSTMENT REFRIGERATOR section Turn too warm REFRIGERATOR control to next higher number wait 24 hours then re check Turn FREEZER control to next higher number wait 24 hours Then re check e Door opened often e Large amount of food added e Room temperature very warm FREEZER section too warm ice not made fast enough Door opened often e Large amount of food added Very cold room temperature can t cycle often enough Heavy ce usage Air vents blocked by items Move items out of airstream REFRIGERATOR section too Turn cold REFRIGERATOR control to next lower number wait 24 hours then re check Controls not set correctly for your conditions FREEZER section too cold Controls not set correctly for your conditions Turn FREEZER control to next lower number wait 24 hours then re check 21 USING YOUR RE
13. moisture proof Rewrap if necessary Leftovers Cover leftovers with plastic wrap or aluminum foil Plastic containers with tight lids can also be used STORING FROZEN FOOD NOTE For further information about preparing food for freezing or food storage times check a freezer guide or a reliable cookbook 22 Packaging Successful freezing depends on correct packaging When you close and seal the package it must not allow air or moisture in or out If you do you could have food odor and taste transfer throughout the refrigerator and also dry out frozen food Packaging recommendations Rigid plastic containers with tight fitting lids e Straight sided canning freezing jars Heavy duty aluminum foil Plastic coated paper Non permeable plastic wraps Specified freezer grade self sealing plastic bags Follow package or container instructions for proper freezing methods Do not use Bread wrappers e Non polyethylene plastic containers Containers without tight lids Wax paper or wax coated freezer wrap e Thin semi permeable wrap Freezing IMPORTANT Do not store bottles in the freezer compartment they may break when frozen causing damage Your freezer will not quick freeze any large quantity of food Do not put more unfrozen food into the freezer than will freeze within 24 hours no more than 2 to 3 Ibs of food per cubic foot of freezer space Leave enough space in the freezer for air to circulat
14. onto the middle hinge pin 7 e Install the top hinge 10 with serews e Reinstall top hinge cover 11 18 Handle type 1 y AO m Handle type 2 REFRIGERATOR INSTALLATION 7 After Completing the Job 3 Open both doors again and check to make sure that they close easily If not tilt the refrigerator slightly more to the rear by turning both leveling screws clockwise It may take several more turns and you should turn both leveling screws the same amount e Make sure that the four corners of the door gasket are not folded over To ensure a good seal apply a small amount of silicon grease on the gasket 4 Check using a level 5 Replace the base grille Door Alignment If the space between your doors is uneven follow the instructions below to align the doors 1 Pry off the top hinge cover 2 Loosen the top hinge screws using a 10 mm socket or wrench 3 Have someone hold the door in place or put a DOOR CLOSING AND ALIGNMENT spacer between the doors while you tighten the top hinge screws Door Closing 4 Replace the top hinge cover Your refrigerator has two front leveling screws one on the right and one on the left If your refrigerator seems unsteady or you want the doors to close easier adjust the refrigerator tilt using the instructions below 1 Plug the refrigerator power cord into a 3 prong grounded outlet Move the refrigerator into its final positi
15. removing a light bulb turn the control Thermostat Refrigerator Control or Freezer Control depending on the model to OFF and then disconnect the refrigerator from the electrical source When you are finished reconnect the refrigerator to the electrical source and reset the control Thermostat Refrigerator Control or Freezer Control depending on the model to the desired setting USE OF EXTENSION CORDS Because of potential safety hazards under certain conditions we strongly recommend against the use of an extension cord However if you still elect to use an extension cord it is absolutely necessary that it be a UL listed in the United States 3 wire grounding type appliance extension cord having a grounding type plug and outlet and that the electrical rating of the cord be 15 amperes minimum and 120 volts Use of an extension cord will increase the clearance needed for the back of the refrigerator PARTS AND FEATURES Use this section to become more familiar with the parts and features NOTE This guide covers several different models The refrigerator you have purchased may have some or all of the items listed below The locations of the features shown below may not match your model O Digital Se
16. the power will be out for 24 hours or less keep both refrigerator doors closed to help foods stay cold and frozen 2 If the power will be out for more than 24 hours a Remove all frozen food and store it in a frozen food locker OR b Place 2 Ibs of dry ice in the freezer for every cubic foot of freezer space This will keep the food frozen for two to four days While handling dry ice wear gloves to protect your hands from frostbite OR c If neither a food locker nor dry ice is available consume or can perishable food at once 31 WHEN YOU GO ON VACATION If you choose to leave the refrigerator on while you are away follow these steps to prepare your refrigerator before you leave 1 Use up any perishables and freeze other items 2 Empty the ice bin If you choose to turn the refrigerator off before you leave follow these steps 1 Remove all food from the refrigerator 2 Depending on your model set the thermostat control refrigerator control to OFF See the Setting the Controls section 3 Clean refrigerator wipe it and dry well 4 Tape rubber or wood blocks to the tops of both doors to prop them open far enough for air to get in This stops odor and mold from building up WHEN YOU MOVE When you are moving your refrigerator to a new home follow these steps to prepare it for the move 1 Remove all food from the refrigerator and pack all frozen food in dry ice 2 Depending on your model
17. you intentionally release this CFC refrigerant you can be subject to fines and imprisonment under provisions of environmental legislation GROUNDING REQUIREMENTS IMPORTANT Please read carefully TO CONNECT ELECTRICITY 44 WARNING Electrical Shock Hazard FOR PERSONAL SAFETY this appliance must be properly grounded Have the wall outlet and the circuit checked by a qualified electrician to make sure the outlet is properly grounded 3 prong grounding type wall receptacle 3 prong grounding a plug gt N j ON S Ensure proper ground exists before use RECOMMENDED GROUNDING METHOD The refrigerator should always be plugged into its own individual properly grounded electrical outlet rated for 115 Volts 60 Hz AC only and fused at 15 or 20 amperes This provides the best performance and also prevents overloading house wiring circuits which could cause a fire hazard from overheated wires It is recommended that a separate circuit serving only this appliance be provided Use a receptacle which cannot be turned off with a switch or pull chain Do not use an extension cord Where a standard two prong wall outlet is encountered it is your personal responsibility and obligation to have it replaced with a properly grounded three prong wall outlet Do not under any circumstances cut or remove the third ground prong from the power cord NOTE Before performing any type of installation cleaning or
18. 32 GR PRIESN anank Far 2 Connecting the Water Line 33 35 Crisper Humidity Control 24 Optibin Crisper 24 Troubleshooting Guide 36 39 Crisper cover with lattice on inner surface 25 visit our web site http www Igservice com LG Electronics LIMITED WARRANTY United States of America LG Electronics will repair or at its option replace without charge your product which proves to be defective in material or workmanship under normal use during the warranty period listed below from the date of original purchase This warranty is good only to the original purchaser of the product during the warranty period as long as it is in the U S including Alaska Hawaii and U S Territories LG Refrigerator Freezer Warranty Period Product Parts Labor Refrigerator Freezer 1 year 1 year In Home Service Except Model GR 051 Sealed System 7 years 1 year In Home Service Except Model GR 051 Compressor Condenser Evaporator No other express warranty is applicable to this product THE DURATION OF ANY IMPLIED WARRANTIES INCLUDING THE IMPLIED WARRANTY OF MERCHANTABILITY IS LIMITED TO THE DURATION OF THE EXPRESS WARRANTY HEREIN LG ELECTRONICS SHALL NOT BE LIABLE FOR THE LOSS OF USE OF THE PRODUCT INCONVIENCE LOSS OR ANY OTHER DAMAGES DIRECT OR CONSEQUENTIAL ARISING OUT OF THE USE OF OR INABILITY TO USE THIS PRODUCT OR FOR ANY BREACH OF ANY EXPRESS OR IMPLIED WARRANTY INCLUDING THE IMPLIED WARRANTY OF MERCHANTABILITY APPLICABLE TO THIS PROD
19. FRIGERATOR FOOD STORAGE GUIDE Storing Fresh Food Wrap or store food in the refrigerator in airtight and moisture proof material unless otherwise noted This prevents food odor and taste transfer throughout the refrigerator For dated products check date code to ensure freshness Butter or margarine Keep opened butter in a covered dish or closed compartment When storing an extra supply wrap in freezer packaging and freeze Cheese Store in the original wrapping until you are ready to use it Once opened rewrap tightly in plastic wrap or aluminum foil Milk Wipe milk cartons For best storage place milk on interior shelf not on door shelf Eggs Store in original carton on interior shelf not on door shelf Fruit Wash let dry and store in refrigerator in plastic bags or in the crisper Do not wash or hull berries until you are ready to use them Sort and keep berries in their original container in a crisper or store in a loosely closed paper bag on a refrigerator shelf Leafy vegetables Remove store wrapping and trim or tear off bruised and discolored areas Wash in cold water and drain Place in a plastic bag or plastic container and store in the crisper Vegetables with skins carrots peppers Place in plastic bags or plastic container and store in crisper Fish Use fresh fish and shellfish the same day purchased Chef fresh Store most chef fresh in original wrapping as long as it is airtight and
20. GARANTIAS IMPLEMENTADAS INCLUYENDO LA GARANTIA DE COMPRA APLICADA A ESTE PRODUCTO Algunos estados no permiten la exclusi n o limitaci n de da os incidentales o consecuenciales o limitaciones en cuanto al tiempo que dura una garant a impl cita por lo que algunas de estas limitaciones o exclusiones pueden no aplicarse a usted Esta garant a le otorga derechos legales espec ficos y usted puede adem s tener otros derechos los cuales var an de Estado a Estado LA GARANTIA ANTERIOR NO APLICA A 1 Servicio a su casa para entregar recoger instalar o reemplazar fusibles caseros corregir cableado casero o plomer a correcci n de reparaciones no autorizadas 2 Da o al producto causado por accidente plagas incendios inundaciones o actos por naturaleza 3 Reparaciones cuando su producto LG sea usado diferente a lo normal 4 Da o resultante de accidente alteraci n mal uso o instalaci n inadecuada Por lo tanto estos costos ser n pagados por el consumidor Si el producto es instalado fuera del rea normal de servicio cualquier costo de transportaci n relacionado en la reparaci n del producto o el reemplazo de partes defectuosas ser n cargados al propietario N MEROS DE ASISTENCIA AL CLIENTE Para obtener cobertaura de la Garant a Conserve su factura para comprobar la fecha de compra Una copia de su recibo de compra debe ser entregada cuando se le proporcione el servicio de garant a Para obtener informaci n Ll
21. R The icemaker water valve will buzz as the icemaker fills with water If the power switch is in the I on position it will buzz even if it has not yet been hooked up to water To stop the buzzing move the power switch to O off NOTE Keeping the power switch in the I on position before the water line is connected can damage the icemaker You will hear the sound of cubes dropping into the bin and water running in the pipes as the icemaker refills PREPARING FOR VACATION Set the icemaker power switch to O off and shut off the water supply to the refrigerator If the ambient temperature will drop below freezing have a qualified servicer drain the water supply system on some models to prevent serious property damage due to flooding from ruptured water lines or connections CONNECTING THE WATER LINE NOTE Water line installation is needed when the Automatic Ice Maker and or Water Dispenser features are available on your product BEFORE YOU BEGIN This water line installation is not warranted by the refrigerator or icemaker manufacturer Follow these instructions carefully to minimize the risk of expensive water damage Water hammer water banging in the pipes in house plumbing can cause damage to refrigerator parts and lead to water leakage or flooding Call a qualified plumber to correct water hammer before installing the water supply line to the refrigerator To prevent burns and product damage do not ho
22. STALLATION HOW TO REMOVE AND INSTALL THE 2 Installing Pullout Drawer RELEASE DRAWER Pull both rails 1 out to full extension IMPORTANT To avoid possible injury product or property damage you will need two people to perform the following instructions 1 Removing Pullout Drawer e Pull the drawer open to full extension Remove the screw 1 from each side of rail system Hook the door supports 2 into the rail tabs 3 as illustrated and lower door into final position Remove the lower basket 2 by lifting basket from rail system With the drawer pulled out to full extension insert the lower basket 4 in rail assembly Lift the top of door to unhook door supports from rail system Lift door out to remove 15 REFRIGERATOR INSTALLATION REMOVING REVERSING AND REPLACING REFRIGERATOR DOORS OPTIONAL NOTE See the Parts and Features section on pages 9 10 to match your model TOOLS NEEDED 10mm hex head socket wrench No 2 Phillips screwdriver flat head screwdriver 10mm open end wrench flat 2 inch putty knife IMPORTANT Before you begin turn the refrigerator OFF and unplug it Remove food and any adjustable door or utility bins from doors HOW TO REVERSE DOOR OPENING DIRECTION when converting from the left opening type to right opening type 1 Removing Refrigerator Door Remove the top hinge cover 1 e Remove the 3 screws and lift off the top hin
23. Swing Type Models 1 To remove wire Durabase pull wire durabase out to full extension Tilt up the front of the wire Durabase and pull it straight out 2 To install insert the wire Durabase into frame rails and push back into place USING YOUR REFRIGERATOR ilti i ff door DURABASE DIVIDER How to lock the tilting function of freezer door The Durabase divider allows the option to organize 1 Open the freezer door the Durabase area into sections and remove 1 2 Insert part 1 into 2 NOTE If you lock the tilting function when the door is tilted you cannot close it PULLOUT DRAWER BASKETS 1 To remove pull divider straight up 1 To remove lift basket up and pull straight out 2 To install hook top corners of divider over top horizontal durabase a or basket rungs b DRAWER TRAY on some models The drawer tray prevents small food items from falling between the basket rungs 2 To Install pull both rails out to full extension Hook the basket supports into the rail tabs and push to the back of compartment TILTING DOOR on some models The tilting door provides easy access to stored foods How to use WIRE BASKET Swing Type Models Tilt the door down and pull it out 1 To remove the wire basket pull it out as far as it goedilt the front up and Pill it straight out 2 To replace the wire basket place it in the frame rails and push it back into pl
24. UCT Some States do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long an implied warranty lasts so these limitations or exclusions may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state THE ABOVE WARRANTY DOES NOT APPLY TO Service trips to your home to deliver and pickup install instruct or replace house fuses or correct house wiring or plumbing or correction of unauthorized repairs Damage to the product caused by accident pests fire floods or acts of God Repairs when your LG product is used in other than normal single family household use Damage resulting from accident alteration misuse abuse or improper installation Therefore these costs are paid by the consumer If the product is installed outside the normal service area any cost of transportation involved in the repair of the product or the replacement of defective parts shall be borne by the owner CUSTOMER ASSISTANCE NUMBERS To obtain Warranty Coverage Retain your Bill of Sale to prove date of purchase A Copy of your Sales Receipt must be submitted at the time warranty service is provided To obtain Product or Customer Call 1 877 714 7486 24 hrs a day 7 days per week 365 days per year Service Assistance Press the appropriate menu option and have your product type Refrigerator model number serial number and ZIP Postal
25. ace Warning Watch your step when you open tilting door 27 USING YOUR REFRIGERATOR CAN DISPENSER on some models FREEZER SHELF on some models The Can Dispenser slides out from underneath the shelf To remove the shelf take it from the front part and pull it The Can Dispenser holds up to twelve 12 ounce towards you beverage cans To place the shelf reverse the removal procedure 1 To remove the can dispenser pull it out as far as it comes Tilt the front up and pull it straight out 2 To Install the can dispenser place it into the shelf frame rails and push it into place TRIPLE TWIST ICE TRAY on some models e If the tray is filled with water to the highest level it will be difficult to remove ce cubes For quick freeze adjust the freezer dial to 3 To remove ice cubes twist the tray Twist the knob clockwise completely CAUTION e If you twist the knob before the water freezes it will spill into the ice bin and the cubes there will be frozen together 28 USING YOUR REFRIGERATOR FILTER on some models It is recommended that you replace the filter when the water filter indicator light turns on or your water dispenser or ice maker decreases noticeably 7 After changing the water filter cartridge reset the water filter status display and indicator light by pressng and holding the BUTTON for 3 seconds 1 Remove the old cartridge Rotate the k
26. allon containers or bottles by simply sliding the shelf back USING YOUR REFRIGERATOR CHEF FRESH SNACK PAN on some models You can store small vegetables or fruits requiring more or less humidity in separate drawers While holding the chef fresh with one hand pull it forward slightly Lift slightly and pull it out To remove the crisper door flap on some models 1 Raise the door as high as it will open 2 Using your finger press the plastic hinge toward the center of the door flap CRISPER HUMIDITY CONTROL 3 Lift the door out of its place You can control the amount of humidity in the moisture 4 Replacement is the opposite of removal sealed crispers Adjust the control to any setting between amp and 3 amp 35 lets moist air out of the crisper for best storage of fruits e 4 keeps moist air in the crisper for best storage of fresh leafy vegetables To remove the glass 1 Lift up the glass after inserting a screwdriver under the criper cover 2 Pull up and out OBTIBIN CRISPERS The OptiBin Crispers provide fresher tasting fruit and vegetables by letting you easily control humidity inside the crisper The OptiBin Crispers include 1 a humidity control knob at the front of the crisper cover and 2 a large lattice on the inner surface of the cover to hold or release moisture To remove the crisper 1 Slide crisper straight out
27. ame al 1 877 714 7486 24 hrs al d a 7 d as por semana 365 d as al a o Servicio de Asistencia Presione la opci n de men apropiado y tenga su tipo de producto Refrigerador n mero de modelo n mero de serie y ZIP C digo Postal listos Para obtener el Centro de Servicio Autorizado Llame al 1 877 714 7486 m s cercano 24 hrs al d a 7 d as por semana 365 d as al a o Presione la opci n adecuada y tenga su tipo de producto Refrigerador n mero de modelo n mero de serie y ZIP c digo Postal listos Visiter notre site web http www Igservice com LG Electronics GARANTIE LIMIT E anada LG Electronics r parera ou remplacera sa discr tion sans frais le produit pr sentant des d fauts de mat riaux ou de fabrication dans des conditions normales d utilisation pendant la p riode de garantie indiqu e ci dessous partir de la date d achat d origine Cette garantie est valide pour seulement l acheteur d origine du produit pendant la p riode de garantie en autant que cela soit aux E U incluant Alaska Hawaii territoires am ricains et toutes les provinces canadiennes P riode de garantie du refrig rateur cong lateur LG Produit Pi ces Main d uv re R frig rateur cong lateur 2 ans 2 ans service domicile sauf mod le GR 051 Syst me scell 5 ans 2 ans service domicile sauf mod le GR 051 compresseur condensateur vaporateur Aucune autre garantie expresse est applicable
28. ant Safety Instructions section Refrigerator shelves are installed in the shipping position Please reinstall shelves according to your individual storage needs When Moving Your Refrigerator Your refrigerator is heavy When moving the refrigerator for cleaning or service be sure to protect the floor Always pull the refrigerator straight out when moving it Do not wiggle or walk the refrigerator when trying to move it as floor damage could occur WARNING Explosion Hazard Keep flammable materials and vapors such as gasoline away from refrigerator Failure to do so can result in death explosion or fire 12 INSTALLATION 1 Avoid placing the unit near heat sources direct sunlight or moisture To avoid vibration the unit must be level If required adjust the leveling screws to compensate for unevenness of the floor The front should be slightly higher than the rear to aid in door closing Leveling screws can be turned easily by tipping the cabinet slightly Turn the leveling screws clockwise iiias to raise the unit counterclockwise Mk to lower it Install this appliance in an area where the temperature is between 55 F 13 C and 110 F 43 C If the temperature around the appliance is too low or high cooling ability may be adversely affected NEXT 1 Clean your refrigerator thoroughly and wipe off all dust accumulated during shipping Install accessories such as ice cube
29. at any servicing be performed by a qualified individual Before replacing a burned out light bulb unplug the refrigerator or turn off power at the circuit breaker or fuse box in order to avoid contact with a live wire filament A burned out light bulb may break when being replaced NOTE Setting either or both controls to the OFF position does not remove power to the light circuit e Do not store bottles in the freezer compartment they may break when frozen causing damage For personal safety this appliance must be properly grounded Have the wall outlet and the circuit checked by a qualified electrician to make sure the outlet is properly grounded Read all instructions before using this appliance Use this appliance only for its intended purpose as described in this use and care guide After your refrigerator is in operation do not touch the cold surfaces in the freezer compartment when hands are damp or wet Skin may adhere to the extremely cold surfaces In refrigerators with automatic icemakers avoid contact with the moving parts of the ejector mechanism or with the heating element that releases the cubes DO NOT place fingers or hands on the automatic icemaking mechanism while the refrigerator is plugged in DO NOT refreeze frozen foods which have thawed completely The United States Department of Agriculture in Home and Garden Bulletin No 69 says You may safely refreeze frozen foods that have thaw
30. ates between both sections any odors formed in one section will transfer to the other You must thoroughly clean both sections to eliminate odors To prevent odor transfer and drying out of food wrap or cover foods tightly See the Food Storage Guide section for details 20 SETTING THE CONTROLS Your refrigerator has two controls that let you regulate the temperature in the freezer and refrigerator compartments Initially set the REFRIGERATOR CONTROL at 37 F 3 C and the FREEZER CONTROL at 0 F 18 C Leave it at this setting for 24 hours one day to stabilize Then adjust the compartment temperature as desired gt Premium Model Refrigerator control 32 F to 46 F 0 C to 8 C The lower the number setting the colder the refrigerator compartment will become EXPRESS REFRIGERATOR TEMP FREEZING O 15 COLDER WARMER F ISRECOMMENDED a o Freezer control 6 F to 9 F 21 C to 13 C When the setting is at a lower number the freezer compartment becomes colder But the refrigerator compartment becomes warmer because less cold air flows into the refrigerator Express Freezing Press the Express Freezing key and the LED will turn on This function will remain activated for 24 hours and intensify the cooling speed of freezer and increase the amount of ice EXPRESS FREEZING FREEZER TEMP a 086 0 FIS RECOMMENDED COLDER WARMER NOTE To change F C press an
31. bin drawers shelves etc in their proper places They are packed together to prevent possible damage during shipment Let your refrigerator run for 2 or 3 hours before putting food in it Check the flow of cold air in the freezer compartment to ensure proper cooling Your refrigerator is now ready for use CAUTION Be careful when you work with hinge base grille stopper etc You may be injured Do not put hands or metal sticks into air vents base grille or bottom of refrigerator You may be injured or receive an electrical shock BASE GRILLE To remove the base grille 1 Grasp the grille with both hands 2 Pull the grille toward yourself To install the base grille 1 Place clips in openings in the metal panel 2 Push the grille toward the refrigerator until it snaps into place REFRIGERATOR INSTALLATION REMOVING REVERSING AND REPLACING REFRIGERATOR DOORS OPTIONAL NOTE See the Parts and Features section on pages 9 10 to match your model NOTE Reversing the refrigerator door is not possible on water dispenser models TOOLS NEEDED 10mm hex head socket wrench No 2 Phillips screwdriver flat head screwdriver 10mm open end wrench flat 2 inch putty knife IMPORTANT Before you begin turn the refrigerator OFF and unplug it Remove food and any adjustable door or utility bins from doors HOW TO REVERSE DOOR OPENING DIRECTION when converting from the left opening type to right
32. ciently actually are The following describes the kinds of sounds to keep your food items at the desired temperature and what may be making them The high efficiency compressor may cause your new refrigerator to run longer than your old one and you may hear a pulsating or high pitched sound You may hear the evaporator fan motor circulating the air through the refrigerator and freezer compartments xk As each cycle ends you may hear a gurgling sound due to the refrigerant flowing in your refrigerator Contraction and expansion of the inside walls may cause a popping noise Water dripping on the defrost heater during a defrost cycle may cause a sizzling sound You may hear air being forced over the condenser by the condenser fan A You may hear water running into the drain pan during the defrost cycle Note Due to refrigerator s low energy consumption design the fans will remain off by the door switch activates the inner compartment light REFRIGERATOR DOES NOT OPERATE Check if Then The power supply cord is unplugged Firmly plug the cord into a live outlet with proper voltage A household fuse has blown or circuit Replace the fuse or reset the circuit breaker breaker tripped The The refrigerator control is set to the OFF position The refrigerator control is set to the OFF position is set to the OFF position Refer to the Refer to the Setting the Controls the Controls Refrigerat
33. cking Clean gaskets and the surface that they touch Rub a thin coat of paraffin wax on the gaskets after cleaning The refrigerator wobbles or seems unstable Level the refrigerator Refer to the Door Closing and Alignment Section The doors were removed during product installation Remove and replace the doors according to the Removing and not properly replaced Reversing and Replacing Refrigerator Doors section or call a qualified service technician FROST OR ICE CRYSTALS ON FROZEN FOOD Check if Then The door is not closing properly See Doors will not close completely above The door is opened often When the door is opened warm humid air is allowed in the freezer resulting in frost 37 TROUBLESHOOTING GUIDE ICE HAS OFF TASTE OR ODOR Check if Then The icemaker was recently installed Discard first few batches of ice to avoid discolored or off flavored ice The ice has been stored for too long Throw away old ice and make new supply The food has not been wrapped tightly in Rewrap foods since odors may migrate to the ice if food either compartment is not wrapped properly The water supply contains minerals such as sulfur A filter may need to be installed to eliminate taste and odor problems The interior of refrigerator needs cleaning See Care and Cleaning section Ice storage bin needs cleaning Empty and wash bin Discard old cubes THERE IS WATER INTHE DEFROST DRAIN PAN Check if Then The r
34. d HOLD COLDER key of freezer and COLDER key of refrigerator over 1 sec at the same time gt Dispenser Model Refrigerator control 32 F to 46 F 0 C to 8 C The lower the number setting the colder the refrigerator compartment will become REFRIGERATOR TEMP DISPENSER EREK ING VO BEEM COLDER WARMER Lock F ISRECOMMENDED Freezer control 6 F to 9 F 21 C to 13 C When the setting is at a lower number the freezer compartment becomes colder But the refrigerator compartment becomes warmer because less cold air flows into the refrigerator USING YOUR REFRIGERATOR Dispenser Lock Press and hold the DISPENSER LOCK button for 3 seconds to lock the dispenser When locked the LED on the door will be off and the dispenser function is turned off Press and hold the DISPENSER LOCK button again for 3 seconds to unlock the dispenser The LED on the door will be on and dispenser will function normally DISPENSER LOCK WATER FILTER FREEZER TEMP o EEB 00 0 FIS RECOMMENDED RESET COLDER WARMER FREEZING NOTE To change F C press and HOLD COLDER key of freezer and COLDER key of refrigerator over 1 sec at the same time Power failure Compensation Function When the power is off the Fresh Food and Freezer Temperature notches the filter elapsed time for replacement the temperature mode C of F and the dispenser lock mode are saved gt Mid Entry Models R
35. e around packages Be careful to leave enough room at the front so the door can close tightly Storage times will vary according to the quality and type of food the type of packaging or wrap used airtight and moisture proof and the storage temperature Ice crystals inside a sealed package are normal This simply means that moisture in the food and air inside the package have condensed creating ice crystals NOTE Allow hot foods to cool at room temperature for 30 minutes then package and freeze Cooling hot foods before freezing saves energy NOTE Do not store food near the sensor it may cause the sensor to malfunction 44 WARNING Suffocation Hazard When using dry ice provide adequate ventilation Dry ice is frozen carbon dioxide CO When it vaporizes it can displace oxygen causing dizziness light headedness unconsciousness and death by suffocation Open a window and do not breathe the vapors USING YOUR REFRIGERATOR REFRIGERATOR SHELVES The shelves in your refrigerator are adjustable to meet your individual storage needs These units are all glass shelves Storing similar food items together in your refrigerator and adjusting the shelves to fit different heights of items will make finding the exact item you want easier it will also reduce the amount of time the refrigerator door is open saving energy IMPORTANT Do not clean glass shelves with warm water when they are cold Shelves may break if ex
36. ed if they still contain ice crystals or if they are still cold below 40 F 4 C Thawed ground meats poultry or fish that have any off odor or off color should not be refrozen and should not be eaten Thawed ice cream should be discarded If the odor or color of any food is poor or questionable get rid of it The food may be dangerous to eat Even partial thawing and refreezing reduces the eating quality of foods particularly fruits vegetables and prepared foods The eating quality of red meats is affected less than that of many other foods Use refrozen foods as soon as possible to save as much of their quality as you can SAVE THESE INSTRUCTIONS 7 DANGER risk OF CHILD ENTRAPMENT Child entrapment and suffocation are not problems of the past Junked or abandoned refrigerators are still dangerous even if they will sit for just a few days If you are getting rid of your old refrigerator please follow the instructions at right to help prevent accidents BEFORE YOU THROW AWAY YOUR OLD REFRIGERATOR OR FREEZER Take off the doors e Leave the shelves in place so that children may not easily climb inside CFC DISPOSAL Your old refrigerator may have a cooling system that used CFCs chlorofluorocarbons CFCs are believed to harm stratospheric ozone If you are throwing away your old refrigerator make sure the CFC refrigerant is removed for proper disposal by a qualified servicer If
37. efrigerator control position 1 to 7 32 F to 46 F or 0 C to 8 C The higher the number setting the colder the refrigerator compartment will become EXPRESS REFRIGERATOR TEMP FREEZING gt Wjswjejojejeje WARMER 4 IS RECOMMENDED COLDER ADJUST e Freezer control position 1 to 7 6 F to 8 F or 21 C to 13 C When the setting is at a higher number the freezer compartment becomes colder But the refrigerator compartment becomes warmer because less cold air flows into the refrigerator Express Freezing Press the Express Freezing key and the LED will turn on This function will remain activated for 24 hours and intensify the cooling speed of freezer and increase the amount of ice EXPRESS FREEZING FREEZER TEMP aaa gt WARMER 41S RECOMMENDED COLDER ADJUST ADJUSTING CONTROL SETTINGS Give the refrigerator time to cool down completely before adding food It is best to wait 24 hours before you put food into the refrigerator The mid settings indicated in the previous section should be correct for normal household refrigerator usage The controls are set correctly when milk or juice is as cold as you like and when ice cream is firm The refrigerator control functions as the thermostat for the entire appliance refrigerator and freezer sections The higher the number setting the longer the compressor will run to keep the temperature colder The freezer control adjusts the
38. efrigerator is defrosting The water will evaporate It is normal for water to drip into the defrost pan It is more humid than normal Expect that the water in the defrost pan will take longer to evaporate This is normal when it is hot or humid THE REFRIGERATOR SEEMS TO MAKE TOO MUCH NOISE Check if Then The sounds may be normal for your refrigerator Refer to the Understanding Sounds You May Hear section THE ICEMAKER IS NOT PRODUCING ICE OR ICE CUBES ARE FREEZING TOO SLOWLY Check if Then The freezer temperature is cold enough to produce ice Wait 24 hours after hook up for ice production See the Setting the Controls Section Door left open Check to see if something is holding the door open CUBES PRODUCED BY ICEMAKER ARE TOO SMALL Check if Then Smaller cube size level is selected Select larger cube size using cube size selector Water shutoff valve connecting refrigerator to water Call a plumber to clear the valve line may be clogged THE DOORS ARE DIFFICULT TO OPEN Check if Then The gaskets are dirty or sticky Clean gaskets and the surfaces that they touch Rub a thin coat of appliance polish or kitchen wax on the gaskets after cleaning The door is reopened within a short time after having When you open the door warmer air enters the refrigerator been opened As the warm air cools it can create a vacuum If the door is hard to open wait 5 minutes to allow the air pressure to
39. er compression nuts and 2 ferrules sleeves to connect the copper tubing to the shutoff valve and the refrigerator water valve If your existing copper water line has a flared fitting at the end you will need an adapter available at plumbing supply stores to connect the water line to the refrigerator OR you can cut off the flared fitting with a tube cutter and then use a compression fitting Shutoff valve to connect to the cold water line The shutoff valve should have a water inlet with a minimum inside diameter of 5 32 at the point of connection to the COLD WATER LINE Saddle type shutoff valves are included in many water supply kits Before purchasing make sure a saddle type valve complies with your local plumbing codes INSTALLATION INSTRUCTIONS Install the shutoff valve on the nearest frequently used drinking water line that is easily accessible It is best to connect into the side of a vertical water pipe When it is Drill a 1 4 hole in the water pipe even if using a self piercing valve using a necessary to connect into a sharp bit Remove any burrs 1 SHUT OFF THE MAIN WATER SUPPLY Turn on the nearest faucet to relieve the pressure on the line CHOOSE THE VALVE LOCATION Choose a location for the valve horizontal water pipe make the gt connection to the top or side rather than at the bottom to avoid drawing off any sediment from the water pipe DRILL THE HOLE FOR THE VALVE
40. ezer compartment temperature room temperature number of door openings and other operating conditions If the refrigerator is used before the water connection is made to the icemaker set the power switch to O off When the refrigerator has been connected to the water supply set the power switch to I on The icemaker will fill with water when it cools to freezing A newly installed refrigerator may take 12 to 24 hours to begin making ice cubes Throw away the first few batches of ice to allow the water line to clear Be sure nothing interferes with the sweep of the feeler arm 32 When the bin fills to the level of the feeler arm the icemaker will stop producing ice It is normal for several cubes to be stuck together If ice is not used frequently old ice cubes will become cloudy taste stale and shrink NOTE If the cube size is smaller or larger than you expected you can regulate the size with the cube size button nomally caused by variations in water pressure Every time you press the cube size button the indicator light go up The higher position light is on the larger cubes will be 1st step is the next after the 5th step WHEN YOU SHOULD SET THE ICEMAKER POWER SWITCH TO O OFF e When the water supply will be shut off for several hours When the ice storage bin is removed for more than a minute or two When the refrigerator will not be used for several days NORMAL SOUNDS YOU MAY HEA
41. ge 2 Lift the Refrigerator door 3 slightly and remove it Pry off the cover 4 using a slotted screwdriver and attach it on the right Loosen the screw 5 remove the stoppers 6 and attach them on the left on the opposite side e Loosen the pin 8 and remove it e Lift off the washer 9 Pry off the cover 7 using a slotted screwdriver and attach it on the right 2 Removing Freezer Door e Lift the door 10 slightly and remove it Loosen the 2 screws 11 the 2 screws 12 and lift off the middle hinge 13 Take off the base grille 14 Remove the cap 15 and attach it on the right Loosen the 2 screws 16 remove the bottom hinge 17 and attach on the right Loosen the 2 screws 18 remove the bottom hinge 19 and attach on the left e Loosen the 2 screws 20 and attach the stopper 21 on the left side of the base 16 REFRIGERATOR INSTALLATION 3 Removing Refrigerator Handle NOTE To assist in installing the handle on the right side place a small piece of masking tape near the top of the handle before removing e Grasp the handle tightly with both hands and slide the handle up 1 this may require some force The keyhole slots 2 on the back of the handle allow the handle to separate from the mounting screws 3 Use an adjustable wrench to remove the handle mounting screws 3 Carefully pry off the plug buttons 4
42. he tubing is fully inserted into the valve Tighten the compression nut securely Compression Nut lt Packing a Nut g Outlet Ferrule sleeve Valve NOTE Commonwealth of Massachusetts Plumbing Codes 248CMR shall be adhered to Saddle valves are illegal and use is not permitted in Massachusetts Consult with your licensed plumber FLUSH OUT THE TUBING Turn the main water supply on and flush out the tubing until the water is clear An Shut the water off at the water valve after about one quart of water has been flushed through the tubing CONNECTING THE WATER LINE 9 CONNECT THE TUBING TO THE REFRIGERATOR NOTES Before making the connection to the refrigerator be sure the refrigerator power cord is not plugged into the wall outlet If your refrigerator does not have a water filter we recommend installing one If your water supply has sand or particles that could clog the screen of the refrigerator s water valve Install the filter in the water line near the refrigerator Remove the plastic flexible cap from the refrigerator connection Place the compression nut and ferrule sleeve onto the end of the tubing Insert the end of the tubing into the connection as far as possible While holding the tubing tighten the fitting Refrigerator Connection Ferule sleeve Tubing Clamp 1 4 Compression Nut 1 4 Tubing Fasten the tubing into the tubi
43. lick sounds can be heard 4 To move to lowest position make sure if all bins are correctly assembled so that they don t fall out of door Warning Somebody can be hurt if door bins are not firmly assembled NOTE Do not adjust a bin that is loaded with food USING YOUR REFRIGERATOR DAIRY BIN 1 To remove the dairy bin simply lift it and pull straight out 2 To replace the dairy bin slide it in above the desired location and push down until it stops FREEZER WIRE DOOR RACKS Tilt out Door Basket on some models You can remove foods easily by tilting out the wire basket in the freezer compartment 1 To remove the freezer door rack pull the bracket outward until you hear a clicking sound then remove the wire rack 2 To replace the freezer door rack hook the end of the rack in the bracket and push down until the rack locks into place ohn O ii k 26 ICE BIN 1 To remove ice bin pull it out as it comes Tilt up the front of the ice bin and pull straight out 2 To Install insert ice bin into frame rails and push back into place DURABASE To remove the Durabase push it back to the end as much as possible Tilt up the front of the Durabase and pull straight out Drawer Type Models 2 To install insert the Durabase in rail assembly WIRE DURABASE
44. ng Clamp attached to the back of the refrigerator First loosen the screw fastening the clamp Next insert the tubing in the groove Finally re fasten the screw 10 TURN THE WATER ON AT THE SHUTOFF VALVE Tighten any connections that leak Reattach the compressor compartment access cover 11 PLUG IN THE REFRIGERATOR Arrange the coil of tubing so that it does not vibrate against the back of the refrigerator or against the wall Push the refrigerator back to the wall START THE ICEMAKER Set the icemaker power switch to the ON position The icemaker will not begin to operate until it reaches its operating temperature of 15 F 9 C or below It will then begin operation automatically if the icemaker power switch is in the on position TROUBLESHOOTING GUIDE e The defrost timer will click when the automatic defrost UNDERSTANDING SOUNDS YOU MAY HEAR cycle begins and ends The thermostat control or refrigerator control depending on the model will also Your new refrigerator may make sounds that your old one click when cycling on and off didn t make Because the sounds are new to you you might be concerned about them Most of the new sounds Rattling noises may come from the flow of refrigerant the are normal Hard surfaces like the floor walls and water line or items stored on top of the refrigerator cabinets can make the sounds seem louder than they Your refrigerator is designed to run more effi
45. nob of the cartridge counter clockwise TE When the cartridge is removed it will click out of place Pull out the cartridge NOTE There will be water in the cartridge Some spilling may occur through the hole at rear bottom side of cover You may use a cup or something like that to prevent spilt water drop into food 29 2 Replace with a new cartridge Take the new cartridge out of its packaging and remove protective cover from the o rings With cartridge knob in the vertical position push the new filter cartridge into the cover until it stops 7 If you can t turn the filter from side to side it isn t fully inserted Push it in firmly and twist it into place You will hear it click into place Using its handle twist the cartridge clockwise about 1 4 turn You will hear when it clicks into place wy 7 3 Flushing the Water System After Replacing Filter Dispense water through the water dispenser for 3 minutes to purge the system AN NOTE To purchase replacement water filter cartridges visit your local appliance dealer or part distributor You can also visit our website www lgappliances com or call 1 877 714 7481 The replacement water filter cartridge s part number is 5231JA2006B CARE AND CLEANING A WARNING Explosion Hazard Use non flammable cleaner Failure to do so can result in death explosion or fire Both the refrigerator and freezer sections defrost
46. nsor Control Refrigerator Light Q Sheives cher Fresh Snack Pan Q Can Dispenser Optibin Crisper Keeps fruits and vegetable fresh and crisper O customcube Icemaker ce Bin O Durabase O Divider Filter inside Dairy Bin O Design A Door Quo Box Refrigerator Door Rack Q Freezer Light wie Basket QFreezer Door Rack Tilting on some models PARTS AND FEATURES Use this section to become more familiar with the parts and features NOTE This guide covers several different models The refrigerator you have purchased may have some or all of the items listed below The locations of the features shown below may not match your model Q Digital Sensor Control Refrigerator Light O Shelves Snack Pan Optibin Crisper Keeps fruits and vegetable fresh and crisp Tiple Twist Ice Tray O ce Bin wire Durabase 10 Divider D Dairy Bin Q Design A Door D Egg Box Refrigerator Door Rack Freezer Light O wire Basket Q Freezer Wire Door Rack PARTS AND FEATURES
47. ok up the water line to the hot water line If you use your refrigerator before connecting the water line make sure the icemaker power switch is in the O off position Do not install the icemaker tubing in areas where temperatures fall below freezing When using any electrical device such as a power drill during installation be sure the device is double insulated or grounded in a manner to prevent the hazard of electric shock or is battery powered All installations must be in accordance with local plumbing code requirements NOTE Wear eye protection WHAT YOU WILL NEED e Copper Tubing 1 4 outer diameter to connect the refrigerator to the water supply Be sure both ends of the tubing are cut square To determine how much tubing you need measure the distance from the water valve on the back of the refrigerator to the water supply pipe Then add 8 feet 2 4 m Be sure there is sufficient extra tubing about 8 feet 2 4 m coiled into 3 turns of about 10 25 cm diameter to allow the refrigerator to move out from the wall after installation Be sure that the kit you select allows at least 8 feet 2 4 m as described above e A cold water supply The water pressure must be between 20 and 120 p s i on models without a water filter and between 40 and 120 p s i on models with a water filter Power drill 1 2 or adjustable wrench Straight and Phillips blade screwdriver Two 1 4 outer diamet
48. on 2 Use a screwdriver to adjust the leveling screws Turn the leveling screw clockwise to raise that side of the refrigerator or counterclockwise to lower it It may take several turns of the leveling screw to adjust the tilt of the refrigerator NOTE Having someone push against the top of the refrigerator takes some weight off the leveling screws This makes it easier to adjust the screws 19 USING YOUR REFRIGERATOR ENSURING PROPER AIR CIRCULATION In order to ensure proper temperatures air must flow between the refrigerator and freezer sections As shown in the illustration below cool air enters through the bottom of the freezer section and moves up Most of the air then flows through the freezer section vents and recirculates under the freezer floor The rest of the air enters the refrigerator section through the top vent MULTI FLOW The cooling fan operates more powerful and effective than in normal operation This is specially noticeable when new food is placed in the refrigerator compartment If water or foreign substances enter the cool air vent while cleaning efficiency will be lowered In addition if gasket is damaged efficiency may be lowered because of escaping cool air Do not block any of these vents with food packages If the vents are blocked airflow will be interrupted and temperature and moisture problems may occur IMPORTANT Because air circul
49. on inad quate Par cons quent les frais encourus sont imput s au consommateur Si ce produit est install l ext rieur d une zone de service normale tous frais de d placement requis pour la r paration du produit ou le remplacement de pi ces d fectueuses seront imput s au propri taire NUM ROS D E AIDE LA CLIENT LE Pour obtenir une garantie Conserver la facture comme preuve de la date d achat Un exemplaire de la facture doit tre pr sent au moment o un service sous garantie est fourni Pour obtenir un produit ou T l phoner au 1 888 542 2623 lun au ven 7 h 20 h Central de l aide sam 8 h 17 h Central Presser l option du menu appropri e et avoir le type de produit r frig rateur num ro de mod le num ro de s rie et code postal Pour obtenir le centre de service T l phoner au 1 888 542 2623 24 heures par jour 7 jours par semaine le plus proche Presser l option du menu appropri e et avoir le type de produit r frig rateur num ro de mod le num ro de s rie et code postal Visiter notre site web http www lgservice com LG Electronics LIMITED WARRANTY Canada LG Electronics will repair or at its option replace witouth charge your product which proves to be defective in material or workmanship under normal use during the warranty period listed below from the date of original purchase This warranty is good only to the original purchaser of the product during the warranty period
50. ood has just been added It is normal for the refrigerator to run longer in order to cool the refrigerator back down Adding a large amount of food warms the refrigerator See the Food Storage Guide Section In order to conserve energy try to get everything you need out of the refrigerator at once keep food organized so it is easy to find and close the door as soon as the food is removed The refrigerator was recently plugged in and The refrigerator will take up to 24 hours to cool the refrigerator control was set correctly completely The refrigerator control was not set correctly for the See the Adjusting control settings Section surrounding conditions The doors are not closed completely Push the doors firmly shut If they will not shut all the way see Doors will not close completely below The condenser coils are dirty This prevents air transfer and makes the motor work harder Clean the condenser coils Refer to the Care and Cleaning section DOORS WILL NOT CLOSE COMPLETELY Check if Then The refrigerator is not level See the Installation Section to level refrigerator Food packages are blocking the door open Rearrange food containers to clear door and door shelves The ice bin crisper cover pans shelves door bins Push bins all the way in and put crisper cover pans shelves or baskets are out of position and baskets into their correct positions See the Using Your Refrigerator Section The gaskets are sti
51. or is in the defrost cycle Wait about 30 minutes for defrost LL L to end VIBRATION OR RATTLING NOISE Check if Then The refrigerator is not resting solidly on Floor is weak or uneven or leveling legs need adjusting the floor See Installation Section LIGHTS DO NOT WORK Check if Then The power supply cord is unplugged Firmly plug the cord into a live outlet with proper voltage Light bulb is loose in the socket Turn the refrigerator control to the OFF position and unplug the refrigerator Gently remove the bulb and reinsert Then plug in refrigerator and reset the refrigerator control Light bulb has burned out Replace with an appliance bulb of the same wattage size and shape available at your local hardware store See the Changing the Light Bulb s Section Turn the temperature control to the OFF position and unplug the refrigerator prior to replacement TROUBLESHOOTING GUIDE COMPRESSOR MOTOR SEEMS TO RUN TOO MUCH Check if Then The refrigerator that was replaced was an Modern refrigerators with more storage space require older model more operating time The room temperature is hotter than normal The motor will run longer under warm conditions At normal room temperatures expect your motor to run about 40 to 80 of the time Under warmer conditions expect it to run even more often The door is opened often or a large amount Adding food and opening the door warms the refrigerator of f
52. posed to sudden temperature changes or impact such as bumping For your protection glass shelves are made with tempered glass which will shatter into small pebble sized pieces NOTE Glass shelves are heavy Use special care when removing them to avoid dropping them Adjusting Shelves Remove shelves from the shipping position and replace shelves in the position you want To remove a shelf Tilt up the front of the shelf in the direction of 1 and lift it in the direction of 2 Pull the shelf out To replace a shelf Tilt the front of the shelf up and guide the shelf hooks into the slots at a desired height Then lower the front of the shelf so that the hooks drop into the slots NOTE Make sure that shelves are level from one side to the other Failure to do so may result in the shelf falling or spilling food 23 Sliding Out Shelves optional on some models You can slide some glass shelves in and out of your refrigerator as follows To slide the shelf out carefully pull front of shelf toward you To slide shelf in push shelf in until it stops To remove a sliding shelf from its metal frame 1 Pull the shelf out to the stop position 2 Tilt the front of the shelf up and pull it past the stop position 3 Lift up the shelf to remove Replace the shelf by reversing the above steps Convenience Shelves optional on some models Folding Shelf You can store taller items such as g
53. sive cleansers or flammable fluids These can scratch or damage the material CONDENSER COILS Remove grille base See the grille base section on page 7 Use a vacuum cleaner with an extended attachment to clean condenser coils Vacuum coils when dusty or dirty Coils may need to be cleaned as often as every other month Replace grille base LIGHT BULB REPLACEMENT 44 WARNING Electrical Shock Hazard Before replacing a burned out light bulb either unplug the refrigerator or turn off power at the circuit breaker or fuse box NOTE Moving the control to the OFF position does not remove power to the light circuit NOTE Not all appliance bulbs will fit your refrigerator Be sure to replace the bulb with one of the same size shape and wattage To change the refrigerator light 1 Unplug the power cord from the outlet 2 Remove refrigerator shelves 3 Release the hooks on both ends of the light shield and pull the shield down to remove it 4 Turn the bulb counterclockwise 5 Assembly is the reverse order of disassembly CARE AND CLEANING To change the freezer light 1 Unplug refrigerator or disconnect power 2 Reach behind light shield to remove bulb 3 Replace bulb with a 40 watt appliance bulb 4 Plug in refrigerator or reconnect power POWER INTERRUPTIONS If the electricity goes off call the power company and ask how long it will be off 1 If
54. to the stop 2 Lift the front of the crisper then pull it out to remove 3 Replace the crisper by sliding it back in fully past the drawer stop 24 USING YOUR REFRIGERATOR CRISPER COVER WITH LATTICE ON INNER SURFACE on some models To remove the crisper cover 1 Remove both crisper drawers 2 While holding the crisper cover support 2 pull the cover up and out 1 WARNING Be careful when handing glass cover since glass is not attached to cover To remove the lattice on inner surface 1 Remove crisper cover as illustrated above 2 Hold the glass cover and overtum crisper cover 3 For each lattice hold lattice and pull sides of the cover outward to remove lattice To replace lattice on inner surface 1 For each lattice insert middle tab in 1 closed to glass cover and pull sides of the cover to insert lattice DOOR RACKS The door racks may be removed for easier cleaning Snap on Door Racks To remove the racks 1 Remove all items in the door racks 2 Push the rack against the inside wall of the door A and lift up the door rack B te Few To replace the racks 1 Hold either end of the door rack against the inside wall of the door 2 Push down the rack until it locks in place DESIGN A DOOR 1 Bins can be moved to either side of the door 3 To replace the bin slide it in above the desired support and push down until it locks completely so that c
55. turn the thermostat control refrigerator control to OFF See the Setting the Controls section Unplug the refrigerator Empty water from the defrost pan Clean wipe and dry thoroughly Oo ah Q Take out all removable parts wrap them well and tape them together so they don t shift and rattle during the move 7 Depending on the model raise the front of the refrigerator so it rolls more easily OR screw in the leveling legs all the way so they don t scrape the floor See the Door Closing section 8 Tape the doors shut and tape the power cord to the refrigerator cabinet When you get to your new home put everything back and refer to the Installing Your Refrigerator section for preparation instructions ABOUT THE AUTOMATIC ICEMAKER NOTE Automatic Ice Maker feature is included only in certain models Please check your product specification 44 WARNING Personal Injury Hazard Avoid contact with the moving parts of the ejector mechanism or with the heating element that releases the cubes DO NOT place fingers or hands on the automatic icemaking mechanism while the refrigerator is plugged in OPERATION INSTRUCTIONS A newly installed refrigerator may take 12 to 24 hours to begin making ice Icemaker Feeler Arm Cube Size Indicator Light Power Switch Cube Size Select Button The icemaker will produce eight cubes per cycle approximately 100 130 cubes in a 24 hour period depending on fre
56. zardous situation which if not avoided may result in minor or moderate injury or product damage only All safety messages will identify the hazard tell you how to reduce the chance of injury and tell you what can happen if the instructions are not followed A WARNING To reduce the risk of fire electric shock or injury to persons when using your product basic safety precautions should be followed including the following NEVER unplug your refrigerator by pulling on the power cord Always grip the plug firmly and pull it straight out from the outlet Repair or replace immediately all electric service cords that have become frayed or otherwise damaged Do not use a cord that shows cracks or abrasion damage along its length or at either the plug or connector end When moving your refrigerator away from the wall be careful not to roll over or damage the power cord DO NOT store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance DO NOT allow children to climb stand or hang on the refrigerator doors or shelves in the refrigerator They could damage the refrigerator and seriously injure themselves Keep fingers out of pinch point areas clearances between the doors and cabinet are necessarily small Be careful when you open the doors when children are in the area e Unplug your refrigerator before cleaning or making any repairs NOTE We strongly recommend th
57. ze or even out If the temperature is too cold or too warm move the dial one number at a time A large amount of food has just been added Adding food warms the refrigerator lt can take a few hours to the refrigerator or freezer for the refrigerator to return to normal temperature The food is not packaged correctly Wrap food tightly and wipe off damp containers prior to storing in the refrigerator to avoid moisture accumulation If necessary repackage food according to the guidelines in the Food Storage Guide Section The doors are not closing completely See Doors will not close completely The weather is humid In humid weather air carries moisture into refrigerator when doors are opened A self defrost cycle was completed It is normal for droplets to form on the back wall after the refrigerator self defrosts 39 LG Electronics Inc
Download Pdf Manuals
Related Search