GE ZISS480DMSS Side by Side Refrigerator
Contents
1. 15 Use Front Holes to Secure Trim Use Rear Holes to Secure Handle Installation Instructions Door Trim STEP 9A INSTALL OVERLAY PANELS Refrigerator Door Supplied Handle Shown in Overlay Panel Position an Install door panels e Open door to 90 Remove the 6 Phillips head screws from the door handle e Remove handle Retain all screws e Remove 6 screws holding trim lift off trim Retain yall screws e Slide overlay panel into the door trim Dispenser Models Only e The dispenser controls protrude beyond the face of the freezer door To avoid damage to the dispenser the trim at the top of the door should be removed e Remove the screws holding the top trim in place e Place the assembled freezer panel into the bottom channel and slide into the hinge side trim i e Reinstall the top trim piece with screws N e There are two sets of holes in the handle side trim Replace handle side trim by installing the original screws in the REAR screw holes e Secure the handle to the door using the FRONT screw holes e Follow the same procedures to install the opposite panel Use Front Holes e Check to be sure handles are2. e If necessary the fresh food door may be adjusted up or down to align with the freezer door e Use a 5 16 wrench to adjust the hinge pin as shown Notes 19 Note While performing installations described in this book safety glasses or goggles should be worn For Monogram local service in your area call 1 800 444 1845 Note Product improvement is a continuing endeavor at General Electric Therefore materials appearance and specifications are subject to change without notice Monogram GE Consumer Products Pub No 49 60138 2 General Electric Company Louisville KY 40225 Dwg No 164D4373P001 2003 General Electric Company 10 03 JR 25739 1
3. e Adjust the hinge spring to accommodate the panel weight if necessary 14 Installation Instructions STEP 9 INSTALL FRAMED PANELS Go to Step 9A for Overlay Panels Door Trim Refrigerator Door Supplied Handle Shown in 1 4 Panel oo aiii Install door panels e Open door to 90 Remove the 6 Phillips head screws from the door handle e Remove handle Retain all screws e Remove 6 screws holding trim lift off trim Retain screws e Slide framed panel into the door trim Dispenser Models Only e The dispenser controls protrude beyond the face of the freezer door To avoid damage to the dispenser the trim at the top of the door should be removed e Remove the screws holding the top trim in place e Place the freezer panel into the bottom channel and slide into the hinge side trim e Reinstall the top trim piece with screws e There are two sets of holes in the handle side trim Replace handle side trim by installing the original screws in the FRONT screw holes e Secure the handle to the door using the REAR screw holes e Follow the same procedures to install the opposite panel e Check to be sure handles are evenly aligned with each other at the top To adjust loosen handle screws and slide up or down Tighten screws Position
4. Nominal Size Top View 130 DOOR SWING factory setting Scale 1 1 IMPORTANT NOTE FOR DISPENSER MODELS Dispenser models are supplied with two dispenser trims one to fit framed panels and one for overlay panels Dispenser trim fit to the custom panel depends on correct panel thickness Framed panels must be 1 4 nominal Overlay panels should be constructed as shown to accomplish a total 1 100 thickness See pages 7 and 8 for details Design Guide Frameless Cabinets The case trim overlaps cabinets at the top and sides Therefore Refrigerator frameless cabinets may require filler strips to prevent interference with cabinet door swing The opening must allow for filler strips Case Trim 23 7 8 From Rear of Refrigerator Top View 90 DOOR SWING optional setting ae Scale 1 1 FOR DISPENSER MODELS Dispenser models are supplied with two dispenser trims one to fit framed panels and one for overlay 1 4 panels Dispenser trim fit to the custom panel depends on correct panel thickness Framed panels must be 1 4 nominal Overlay panels should be constructed as shown to accomplish a total 1 100 thickness See pages 7 and 8 for details i 3 4 Overlay eee Panel Nominal Size I I I I I I I I I I I l I I I I I I I Ne ae IMPORTANT NOTE i I I I I I I I I I I l I I I I I I I
5. Required DISPENSER TRIM FIT EXAMPLES NOT TO SCALE 1 4 FRAMED PANEL FREEZER DOOR The dispenser trim fits over the 1 4 0 250 Framed Thick custom panel and snaps into the Panel freezer door l l hi e The clips will not engage the door if Ice Water Dispenser i the panel is more than 0 250 thick L j e If the panel is less than 0 250 thick a 1 4 Dispenser Trim noticeable gap may be created around the dispenser trim 3 4 OVERLAY PANEL EEE FREEZER DOOR e The dispenser trim fits over the custom panel and snaps into the freezer door e The clips will not engage the door if rere the panel is more than 1 100 thick 3 4 Overlay Ice Water Dispenser e If the panel is less than 1 100 thick a Panel noticeable gap may be created around the dispenser trim i 1 100 10 Spacer Total Thickness Panel 3 4 Overlay Dispenser Trim Design Guide SIDE PANELS Side panels must be used whenever the sides of the refrigerator will be exposed The 1 4 side panels will slip into the side case trim Secure the panels to the refrigerator with stick on hook and loop fastener strips Order the side panels from the cabinet manufacturer e Cut a notch in the top front corner as shown E 3 to 4 to allow clearance for corner keys in the front L 9 9 16 side trim Depending
6. And Electrical Locations The opening must be prepared with the electrical and water supply located as shown The cutout depth must be 24 The refrigerator will project forward slightly beyond adjacent cabinetry depending on your installation Cutout depth beneath a soffit When installed beneath a soffit the soffit cannot exceed the 24 installation depth shown The top case trim overlaps the bottom of the soffit Additional Specifications e A 115 volt 60Hz 15 or 20 amp power supply is required An individual properly grounded branch circuit or circuit breaker is recommended Install a properly grounded 3 prong electrical receptacle recessed into the back wall Electrical must be located on rear wall as shown Note GFI ground fault interrupter is not recommended e Water line can enter the opening through the floor or back wall The water line should be 1 4 O D copper tubing or GE SmartConnect kit between the cold water line and water connection location long enough to extend to the front of the refrigerator Installation of an easily accessible shut off valve in the water line is required DIMENSIONS AND CLEARANCES 25 3 8 Framed Models 25 3 4 Stainless Steel Models 35 41 or 47 F Case Depth ye f Case Width Shipping height The ee ee iG refrigerator can be adjusted to fit into a L cutout that is 83 1 2 A min to 84 1 2 max 84 From height Note that the Floorto top case trim at the al Top F
7. I Design Guide CUSTOMIZATION BASICS Framed Or Overlay Panels Custom Handles and Accessory Kits Stainless Steel Wrapped Models 36 wide models ZISS360N ZISS360D 42 wide models ZISS420N ZISS420D 48 wide models ZISS480N ZISS480D Trimmed Models 36 wide models ZIS360N ZISB360D ZISW360D 42 wide models ZIS420N ZISB420D ZISW420D 48 wide models ZIS480N ZISB480D ZISW480D Stainless Steel Wrapped Refrigerators Stainless Steel wrapped refrigerators have wrapped doors and grille panel beveled edges and tubular stainless steel handles that coordinate with other Monogram appliances These models are shipped ready for installation Trimmed Refrigerators Trimmed refrigerators are designed to be customized with decorative panels Field installed custom door and grille panels are required Framed panels You may install 1 4 thick custom panels from your cabinet manufacturer The decorative panel slides into the factory installed trim Or order black white and stainless steel accessory panels from your Monogram dealer A Framed Panel YZ Standard Door Handles Standard supplied handles shown in 1 4 panel position Optional Accessory Kits ZKHSS2 Monogram Tubular Stainless Steel handles designed to fit 3 4 overlay panels Accessory Panels White black and stainless steel accessory panels are available from your Monogram dealer Panels are cut to size and ready to install Ove
8. on installation height TOOLS REQUIRED e Tinsnips to cut banding e Stepladder e Bucket e Level e Appliance Hand Truck e Tubing cutter e 7 16 open end wrench e 2 Phillips screwdriver e Drill and appropriate bits e 5 16 7 16 socket e Safety glasses e 1 1 4 open end wrench e Pliers e 1 4 ratchet wrench HARDWARE SUPPLIED e Water filter bypass plug e Anti Tip brackets e 1 4 nut and ferrule e Dispenser trims for 1 4 and 3 4 overlay panels e 12 pan head screws for custom handle installation MATERIALS REQUIRED e 35 long 2x4 for Anti Tip support e 1 4 copper water line tubing or GE SmartConnect Refrigerator Tubing kits e Water shut off valve optional but recommended e Custom panels for doors and grille panel e Screws to secure refrigerator to cabinetry e Stick on hook and loop fastener strips for 1 4 side panels FLOORING For proper installation this refrigerator must be placed on a level surface of hard material that is at the same height as the rest of the flooring This surface should be strong enough to support a fully loaded refrigerator or approximately 1 500 Ibs NOTE Protect the finish of the flooring Cut a large section of the cardboard carton and place under the refrigerator where you are working GROUNDING THE REFRIGERATOR IMPORTANT Please read carefully FOR PERSONAL SAFETY THIS APPLIANCE MUST BE PROPERLY GROUNDED The power cord of this appliance is equipped wi
9. the bracket with wood block to the back wall so that it is 84 or your installation height from the finished floor Use 12 or 14 wood screws See illustration Block Soffit Brackets ta i m Not Required equire Beneath a Height Soffit From Floor to Bottom of Wood Block Side View e Screws must penetrate at least one inch into vertical wall studs e Before pushing the refrigerator into the opening plug the power cord into the receptacle Open the grille panel and reach into the opening at the back to grasp the power cord Pull the power cord into the opening as you push the refrigerator back e Gently push refrigerator into the opening with hands against front corners Important Note When the refrigerator is installed under a soffit or if there is not enough height for this method of security brackets cannot be used Proceed to step 5 to level the refrigerator and then to step 6 to secure refrigerator to cabinets The refrigerator must be secured to prevent tipping Installation Instructions STEP 5 LEVEL REFRIGERATOR All models have point leveling The front is supported by leveling legs the rear is supported by adjustable wheels Both are accessible from the front of the refrigerator e To level the back of the refrigerator turn the 7 16 hex nut located above the front wheels Turn clockwise to raise or counterclockwise to lower
10. 4 9 3 4 68 5 8 e The overlay panel must be constructed according to the specifications shown to achieve the correct total thickness e Alternative panel construction methods such as securing a 3 4 panel to a 1 4 backer panel cannot be used Another method routing a 3 4 thick panel on all sides cannot be used These methods will not result in the required 1 100 panel thickness When a raised panel design is to be used a custom middle rail is required See page 9 for details Cut the dispenser opening after the backer spacer and overlay panels have been assembled IMPORTANT NOTE Maximum total weight for the assembled panels Fresh food door panel 75 Ibs Freezer door panel 53 lbs Cutout e Grille Panel 18 Ibs Dispenser Cutout Position C D E F G 68 3 8 14 9 16 18 9 16 8 3 8 67 13 1 4 17 1 4 9 1 4 68 5 8 14 13 16 18 13 16 17 15 16 3 1 4 C D E 14 9 16 24 9 16 14 13 16 24 13 16 17 15 16 3 1 4 C D E 18 9 16 26 9 16 18 13 16 26 13 16 17 15 16 5 1 4 Design Guide DISPENSER MODELS RAISED OVERLAY PANEL DESIGN 1 4 Backer Panel 10 Spacer When a raised panel design is to be used a 3 4 Overlay Panel custom wide middle rail is required to accept the dispenser trim e The middle rail must be wide enough to allow for the dispenser trim to overlap the opening e The middle rail must be 1 100 total thickness to accept the dispenser trim Wide Middle Rail is
11. FAUT TROIS PERSONNES POUR INSTALLER CORRECTEMENT D UN APPAREIL DE 91 cm 36 po DE LARGE IL FAUT QUATRE PERSONNES POUR L INSTALLATION D UN MOD LE DE 107 OU 122 cm 42 OU 48 po DE LARGE CONTENTS Skill Level Installation of this refrigerator requires basic mechanical carpentry and plumbing skills Proper installation is the responsibility of the installer Product failure due to improper installation is not covered under the GE Appliance Warranty See the Owner s Manual for warranty information WARNING e These refrigerators are top heavy and must be secured to prevent the possibility of tipping forward Anti Tip protection is required See page 12 for details e Use this appliance only for its intended purpose e Immediately repair or replace electric service cords that become frayed or damaged e Unplug the refrigerator before cleaning or making repairs e Repairs should be made by a qualified service technician AVERTISSEMENT e Ces r frig rateurs sont lourds en haut et il faut les arrimer pour viter leur basculement Il faut avoir un syst me de protection contre le renversement Voir les d tails page 12 e Il ne faut utiliser cet appareil que pour l utilisation appropri e e R parer ou remplacer imm diatement tout cordon lectrique effiloch ou endommag e I faut d brancher le r frig rateur avant le nettoyage ou toute intervention e Les r parations doivent tre faites par un technicien
12. Installation Instructions If you have questions call 800 626 2000 or visit our website at www monogram com Side by Side Refrigerators ZIS360N ZISB360D ZISW360D ZISS360N ZISS360D ZIS420N ZISB420D ZISW420D ZISS420N ZISS420D ZIS480N ZISB480D ZISW480D ZISS480N ZISS480D Design Guide With Installation Instructions Monogram Safety Information BEFORE YOU BEGIN Read these instructions completely and carefully IMPORTAN T Save these instructions for local inspector s use Observe all governing codes and ordinances e Note to Installer Be sure to leave these instructions with the Consumer e Note to Consumer Keep these instructions with your Owner s Manual for future reference WARNING This appliance must be properly grounded See Grounding the Refrigerator page 10 AVERTISSEMENT Cet appareil doit tre correctement mis la terre Consulter Mise a la terre du r frig rateur page 10 If you received a damaged refrigerator you should immediately contact your dealer or builder CAUTION Due to the weight and size of this refrigerator and to reduce the risk of personal injury or damage to the product THREE PEOPLE ARE REQUIRED FOR PROPER INSTALLATION OF A 36 WIDE UNIT FOUR PEOPLE ARE REQUIRED FOR INSTALLATION OF A 42 OR 48 WIDE MODEL PRUDENCE A cause du poids et de la taille de ce r frig rator et pour r duire le risque de blessure et de dommages IL
13. alth of Massachusetts Plumbing Codes 248CMR shall be adhered to Saddle valves are illegal and use is not permitted in Massachusetts Consult with your licensed plumber STEP 2A WATER LINE INSTALLATION WITH A REVERSE OSMOSIS SYSTEM Skip this step when not using an RO System If the water supply to the refrigerator is from a Reverse Osmosis Water System use the refrigerator s filter bypass plug Using the refrigerator s water filtration cartridge with the RO filter can result in hollow ice cubes Rotate Clockwise STEP 3 INSTALL SIDE PANELS Skip this step when not using side panels If you are using 1 4 side panels they should be inserted into the case trim Fasten the panels to the refrigerator with stick on hook and loop fastener strips before setting refrigerator in place STEP 4 INSTALL ANTI TIP BRACKETS WARNING ANTI TIP PRECAUTIONS The refrigerator is top heavy and must be secured to prevent the possibility of tipping forward ATTENTION precautions contre LES BASCULEMENTS Le r frig rateur est beaucoup plus lourd en haut et il faut le maintenir en place pour viter la possibilit de son basculement vers l avant e Cut a 2 x 4 block 35 long and secure the block to the mounting brackets provided using 12 or 14 wood screws l 8 HE Installation Mounting Height Bracket From Floor hi t Screws Mounted into Vertical Wall Studs e Secure
14. e used The refrigerator must be secured to prevent tipping e Raise the grille panel to access case trim e Drill hole in trim and drive screw through the trim into adjacent cabinet e Follow the same procedure on the opposite side Raise Grille Panel to Stop Position Drive Screws Through Case Trim Into Adjacent Cabinets STEP 7 ADJUST DOOR SWING NOTE This refrigerator has a 2 position door stop When space does not allow the door to swing open fully to 130 you may change the door swing to a 90 opening Skip this step if door opening is satisfactory for your installation situation Interior e Open the door to view the bottom hinge Note the door stop pin locations The pin is factory installed in the 130 position e Close the door From below use pliers to unscrew the door stop and reinstall into the 90 position Installation Instructions STEP 8 INSTALL GRILLE PANEL To insert framed or overlay panel into the grille e Raise the grille panel to stop position Adjust Nut Below Spring to Accommodate Panel Weight e Loosen screws on side trim behind frame Remove bottom trim e Slide panel over the metal backer panel and into the trim e If necessary tap with a wood block until panel slips under the top trim piece e Reassemble bottom trim Tighten screws
15. evenly aligned with each to Secure Handle other at the top To adjust loosen handle screws and Use Rear Holes slide up or down Tighten screws to Secure Trim Custom handles If you are using custom handles the handle must be e Secure the door trims using both the FRONT and properly secured to the panel before sliding the panel REAR screw holes Use pan head screws to secure the into the trim trim A package of 12 extra pan head screws can be e The cabinet manufacturer will supply the custom found in the literature package Discard supplied handle and hardware handles 16 Installation Instructions STEP 10 INSTALL DISPENSER TRIM Skip this step is you are installing a stainless steel wrapped or a non dispenser refrigerator There are two dispenser trims shipped with your refrigerator Select the appropriate trim for your application Framed Overlay Panel Panel Trim Trim Compare the dispenser trims Note that the inside depth of the frames are different Choose the trim with less depth for framed panels choose the deeper one for overlay panels Dispenser trim fit over the custom panel depends on correct panel thickness See pages 7 and 8 for panel construction information e Press and snap the dispenser trim into the dis penser recess on the refrigerator door If an excessive ga
16. he bottom of the refrigeration case must be removed before the refrigerator is taken off the skid or damage will occur Carefully tilt refrigerator and slide blocks out from beneath e Remove toekick set aside for final installation e Lift the refrigerator off the skid with an appliance dolly Handle from the sides Floor Copper Tubing Compression Nut Saddle Type Shutoff Valve Outlet Valve Ferrule Sleeve NOTE It is best to install the valve into a vertical water pipe If you install the valve into a horizontal water pipe make the connection at the top or side to avoid drawing off any sediment from the water pipe e Drill a 1 4 hole in the water pipe e Fasten the shut off valve to the pipe with pipe clamp e Tighten the clamp screws until the sealing washer begins to swell Do not over tighten e Place a compression nut and ferrule sleeve onto the end of the tubing and connect it to the shut off valve Make sure the tubing is fully inserted into the valve and ferrule is tightened Installation Instructions STEP 2 continued e Turn on the main water supply and flush debris Run about a quart of water through the tubing into a bucket Shut off water supply at the shut off valve NOTE Saddle type shut off valves are included in many water supply kits Before purchasing make sure a saddle type valve complies with your local plumbing codes NOTE Commonwe
17. ie downs STEP 2 INSTALL WATER LINE e A cold water supply is required for automatic icemaker operation The water pressure must be between 40 and 120 p s i e Route 1 4 OD copper or GE SmartConnect plastic tubing between house cold water line and the water connection location e Tubing should be long enough to extend to the front of the refrigerator Allow enough tubing to accommodate bend leading into the water line connection NOTE The only GE approved plastic tubing is supplied in the GE SmartConnect Refrigerator Tubing kits Do not use any other plastic water supply line because the line is under pressure at all times Other types of plastic may crack or rupture with age and cause water damage to your home GE SmartConnect Refrigerator Tubing Kits are available in the following lengths 2 6m WxX08X10002 6 1 8m WxX08X10006 15 4 6m WX08X10015 25 7 6 m WX08X10025 Shut off the main water supply Turn on the nearest faucet long enough to clear the line of water e Install a shut off valve between the icemaker water valve and cold water pipe in a basement or cabinet The shut off valve should be located where it will be easily accessible e Remove the four 7 16 bolts securing the straps to the skid CAUTION po nor ATTEMPT TO ROLL UNIT OFF SKID Remove PRUDENCE IL NE Tie Downs FAUT PAS ESSAYER DE FAIRE ROULER LE REFRIGERATEUR POUR L ENLEVER DE LAY PALETTE e Support blocks on t
18. iller material or foam tape to improve the fit IMPORTANT NOTE Dispenser Models The refrigerator is supplied with two dispenser trims one for framed panels and one for overlay panels e If the panel is less than 0 250 thick a noticeable gap may be created around the dispenser trim Foam tape may be applied on the door to improve the fit Dispenser Cutou Grille Panel 15 3 8 Dispenser Cutout Side by Side in inches A F Bee fee 36 Models 33 1 8 42 Models 39 7 8 48 Models 45 7 8 IMPORTANT NOTE Maximum total panel weight Fresh food door panel 75 lbs Freezer door panel 53 lbs e Grille Panel 18 Ibs e If the panel is more than 0 250 thick the dispenser trim cannot be secured to the door See Dispenser Trim Fit Example page 9 The framed panel must be 1 4 nominal thickness to fit the dispenser trim Dispenser Cutout Position B C D E F G 9 68 3 8 14 9 16 18 9 16 17 13 16 3 1 8 9 1 2 68 3 8 14 9 16 24 9 16 17 13 16 3 1 8 9 1 2 68 3 8 18 9 16 26 9 16 17 13 16 5 1 8 Design Guide 3 4 OVERLAY PANEL DIMENSIONS Overlay Panel For a more custom appearance overlay panels may be installed on trimmed models The overlay panel must be secured to a 1 4 thick backer panel which slides into the trim A spacer panel 0 10 thick must be placed between the overlay and backer panel Assemble the panels w
19. ith glue and screws e Center the spacer panel on the backer panel left to right and top to bottom Secure the panels with glue C l e Center the spacer and backer panel on the overlay 1 4 10 is not always equal to Backer 4 4 top to bottom offset panel and secure with glue and screws Screws must Panel Spacer be countersunk into the backer panel NOTE Left to right offset 10 750 1 100 Total Panel Thickness IMPORTANT NOTE Dispenser Models The refrigerator is supplied with two dispenser trims one for framed panels and one for overlay panels The overlay dispenser trim is designed to fit a total panel thickness of 1 100 e If the panel is less than 1 100 a noticeable gap may be created around the dispenser trim e If the panel is more than 1 100 the dispenser trim cannot be secured to the door See Dispenser Trim Fit Example page 9 Dispenser Cutou Grille Panel Dispenser 9 5 8 G 36 Side by Side in inches A 1 4 Backer Panel 33 7 8 10 Spacer Panel 33 Freezer Fresh Food 3 4 Overlay Panel 34 1 8 Panel Panel 42 Side by Side in inches A 1 4 Backer Panel 39 7 8 10 Spacer Panel 39 3 4 Overlay Panel 40 1 8 48 Side by Side in inches A 1 4 Backer Panel 45 7 8 10 Spacer Panel 45 3 4 Overlay Panel 46 1 8 9 1 2 68 3 8 8 5 8 67 13 1 4 23 1 4 9 3 4 68 5 8 9 1 2 68 3 8 8 5 8 67 17 1 4 25 1
20. p exists around the dispenser trim or if the panel fits loosely in the door frame foam tape may be applied to help improve the fit Remove the trim and panel and apply foam tape to the door around the dispenser and in the corners STEP 11 CONNECT WATER SUPPLY Check to be sure that refrigerator power cord is not plugged into the wall outlet Te Refrigerator House Water Supply Water Supply e Locate and bring tubing to the front of the cabinet e Turn the water on to flush debris from line Run about a quart of water through tubing into a bucket then shut off water Copper Tubing e Slip a 1 4 nut and ferrule provided over both ends of the copper tubing Insert tube into the union fitting on the unit and tighten nut to union e Turn on the water to check for leaks GE SmartConnect Tubing e Insert the molded end of the tubing into the refrigerator connection Tighten the compression nut until it is just hand tight e Tighten one additional turn with a wrench Overtightening can cause leaks e Turn on the water to check for leaks Note Make sure excess tubing length does not interfere with toekick installation Installation Instructions STEP 12 CONNECT POWER e Check to be sure the power cord is plugged into the receptacle Raise Grille Panel imn Master Light Switch e Check to make sure powe
21. qualifi For Monogram local service in your area 1 800 444 1845 For Monogram service in Canada 1 888 880 3030 For Monogram Parts and Accessories call 1 800 626 2002 www monogram com Planning Guide The Installation Space Dimensions and Clearances 130 Door Swing 90 Door Swing Customization Basics 1 4 Framed Panel Dimensions 3 4 Overlay Panel Dimensions Raised Overlay Panel Design Side Panels Installation Instructions Tools Hardware Materials Grounding the Refrigerator Step 1 Remove Packaging Step 2 Install Water Line Step 2A RO Water Line Step 3 Install Side Panels Step 4 Install Anti Tip Brackets Step 5 Level Refrigerator Step 6 Secure Refrigerator to Cabinetry 13 Step 7 Adjust Door Swing Step 8 Install Grille Panel Step 9 Install Framed Panels Step 9A Install Overlay Panels Step 10 Install Dispenser Trim Step 11 Connect Water Supply Step 12 Connect Power Step 13 Start Icemaker Step 14 Install Toekick Design Guide THE INSTALLATION SPACE 36 Models 12 42 Models 18 48 Models 20 Finished Width 6 i Electrical 84 1 2 max Area 4 Tee 83 1 2 min Finished Opening 75 From Floor to Bottom 24 of Electrical Area T Water Supply f 31 7 M 31 2 The finished cutout width must be 35 1 2 for 36 models 41 1 2 for 42 models 47 1 2 for 48 models Water
22. r to refrigerator is on by opening refrigerator door to see if interior lights are on e The temperature controls are preset at 37 F for the fresh food section and 0 F for the freezer e Allow 24 hours to stabilize before making adjustments STEP 13 START ICEMAKER Power Switch Green Power Light e Flip the switch to I ON The icemaker will begin operation automatically e Be sure nothing interferes with the sweep of the feeler arm e Discard the first full bucket of ice cubes e To turn the icemaker off set the switch to O OFF STEP 14 INSTALL TOEKICK e Locate the supplied toekick shipped taped to the side of the refrigerator Install with 2 screws provided adjust to desired height and tighten Screws e A custom toekick can be installed to match or complement the surrounding cabinetry Use the supplied toekick as a template to cut the shape Supplied Toekick 1 4 or Thicker Toekick ial ieee TETA Y Y INSPECT FINAL INSTALLATION Check door alignment Stand back away from the refrigerator to inspect the final installation e Check to be sure handles are evenly aligned with each other at the top To adjust loosen handle screws and slide up or down Tighten screws e During shipping or the addition of heavy door panels may have caused the doors to move slightly out of alignment N door Out of Alignment CI
23. rame front is 1 2 higher and will overlap upper cabinetry or soffit Use leveling legs and wheels for a maximum 1 height adjustment 36 42 or 48 Frame to Frame Depth Including Handles 26 7 8 Framed Models 27 3 4 Stainless Steel Models Product Clearances These refrigerators are equipped with a 2 position door stop The factory set 130 door swing can be adjusted to 90 if clearance to adjacent cabinets or walls is restricted 130 Door Swing 90 Door Swing eenn 4 Min to Wall A C 36 13 15 20 5 8 42 13 19 26 5 8 48 15 20 28 5 8 Allow minimum clearances for freezer door Dimension A and fresh food door Dimension B for a full 130 door swing and to allow for pan removal 4 minimum clearance is required when door swing is adjusted to 90 If the 90 door stop position is used pan access is maintained but pan removal is restricted See illustrations pages 4 and 5 to determine door swing interaction with adjacent cabinets or countertops Design Guide Frameless Cabinets The case trim overlaps cabinets at the top and sides Therefore frameless cabinets may require filler strips to prevent interfeence with cabinet Refrigerator door swing The opening must allow for filler 23 7 8 From strips Rear of Refrigerator Case Trim 3 4 Overlay Panel En
24. rlay panels You may also choose to install custom overlay panels from your cabinet manufacturer This design provides a seamless appearance which integrates smoothly with surrounding cabinetry ai 3 4 Overlay Panel 10 Thick Spacer Panel 1 4 Thick Backer Panel OH Standard Door Handles Standard supplied handles shown in 3 4 overlay panel position Door Handles The standard supplied handles can be adjusted to accommodate both framed or overlay panels Custom handles of your choice supplied by your cabinet maker can also be installed on overlay panels If desired you may order ZKHSS2 Monogram stainless steel tubular handle kit for 3 4 overlay panels Side Panels Side panels must be used whenever the sides of the refrigerator will be exposed Models White Black Stainless Acrylic Acrylic Steel ZPW480D ZPS480D ZPS480D ZPS480N ZPS420D ZPS420D ZPS420N ZPS360D ZPS360D ZPS360N ZISW480D ZISB480D ZIS480N ZISW420D ZISB420D Z1S420N ZISW360D ZISB360D ZIS360N ZPB480D ZPW480N ZPB480N ZPW420D ZPB420D ZPW420N ZPB420N ZPW360D ZPB360D ZPW360N ZPB360N Design Guide 1 4 FRAMED PANEL DIMENSIONS If you choose to install framed panels they must be cut to the dimensions shown The panels will slide into the frame on the door and grille Non Dispenser Models If the custom panel is less than 1 4 thick and it fits loosely in the door frame it can be backed up with a piece of f
25. th a three prong grounding plug which mates with a standard three prong grounding wall receptacle to minimize the possibility of electric shock hazard from this appliance Have the wall outlet and circuit checked by a qualified electrician to make sure the outlet is properly grounded Where a standard 2 prong wall outlet is encountered it is your personal responsibility and obligation to have it replaced with a properly grounded 3 prong wall outlet DO NOT UNDER ANY CIRCUMSTANCES CUT OR REMOVE THE THIRD GROUND PRONG FROM THE POWER CORD DO NOT USE AN ADAPTER PLUG TO CONNECT THE REFRIGERATOR TO A 2 PRONG OUTLET DO NOT USE AN EXTENSION CORD WITH THIS APPLIANCE Installation Instructions STEP 1 REMOVE PACKAGING CAUTI 0 N Refrigerator is much heavier at the top than at the bottom be careful when moving When using a hand truck handle from side only PRU D E N C E Le r frig rateur est beaucoup plus lourd en haut qu en bas Il faut tre prudent lors des d placements Si un diable est utilis il faut soulever le r frig rateur sur le c t seulement e Carefully cut banding at the top and bottom remove outer carton e Slide out back corner posts 2 e Slide carton off top of cabinet NOTE IT IS NOT NECESSARY TO LAY CABINET DOWN IN ORDER TO REMOVE SKID e The unit is secured to the skid with 4 slotted tie down straps Remove the four 5 16 bolts from the base channels in the t
26. the refrigerator e For front leveling use a 1 1 4 open end wrench e Adjust height of refrigerator to match installation cutout opening 83 1 2 to 841 2 The refrigerator should be level and plumb with cabinetry Hex Nut Adjusts Rear Wheels Leveling Leg i CAUTION The rear leveling wheels and front leveling legs are limited to a maximum height adjustment of 1 If the installation requires more than 84 1 2 height the installer should elevate the refrigerator on a sheet of plywood or runners Cabinetry trim could also be added across the top of the opening to shorten the opening If you attempt to raise the refrigerator more than 1 you will damage the front leveling legs and the rear leveling wheels PRUDENCE Les roues de nivellement arri re et les pattes de nivellement avant permettent un r glage maximal de 25 mm 1 po Si louverture pour le r frig rateur a une hauteur sup rieure a 2 15 m 84 1 2 po Vinstallateur doit lever le r frig rateur sur une feuille de contre plaqu ou des glissi res Il est galement possible d ajouter des baguettes de finition des placards sur le haut de l ouverture afin de la r duire Lever le r frig rateur de plus de 25 mm 1 po endommage les pattes de nivellement avant et les roues de nivellement arri re 13 STEP 6 SECURE REFRIGERATOR TO CABINETRY Whenever possible perform this step for anti tip security or when anti tip brackets cannot b
Download Pdf Manuals
Related Search