Zanussi ZI9225 Refrigerator
Contents
1. ZANUSSI REFRIGERATOR ZI 9155 ZI 9225 INSTRUCTION BOOKLET 2222748 75 A Important Safety Instructions These warnings are provided in the interests of your safety Ensure that you understand them all before installing or using this appliance Your safety is of paramount importance If you are unsure about any of the meanings of these warnings contact the Customer Care Department Prior to Installation Check the appliance for transport damage Under no circumstance should a damaged appliance be installed In the event of damage please contact your retailer Installation This appliance is heavy Care should be taken when moving it It is dangerous to alter the specifications or attempt to modify this product in any way Ensure that the appliance does not stand on the electrical supply cable Important if the supply cable is damaged it must be replaced by a cable available from the manufacturer or your local Service Force Centre Any electrical work required to install this appliance should be carried out by a qualified electrician or competent person Parts which heat up should not be exposed Whenever possible the back of the appliance should be close to a wall but leaving the required distance for ventilation as stated in the installation instructions The appliance should be left for 2 hours after installation before it is turned on in order to allow the refrigerant to settle Refrigerant The refri2. not next to a boiler or radiator or in a very cold room e g an outhouse If these temperatures are exceeded i e warmer or colder then the appliance may not operate correctly For building in and door reversal instructions please refer to the relevant instructions on the following pages A Important It must be possible to disconnect the appliance from the mains power supply the plug must therefore be easily accessible after installation 11 Door reversal The appliance s door has been locked in position for transport by means of pins on both sides According to the door opening direction remove relevant pins at the top and at the bottom Attention After completion of the door reversing operation check that the door gasket adheres to the cabinet If the ambient temperature is cold i e in Winter the gasket may not fit perfectly to the cabinet In that case wait for the natural fitting of the gasket or accelerate this process by heating up the part involved with a normal hairdryer on a low setting 12 Electrical Connection WARNING THIS APPLIANCE MUST BE EARTHED The manufacturer declines any liability should this safety measure not be observed If the plug that is fitted to your appliance is not suitable for your socket outlet it must be cut off and the appropriate plug fitted Remove the fuse from the cut off plug The cut off plug should then be disposed of to pr
3. the screws supplied 7 Fix cover C on guide A until it clips into place 8 Open the appliance door and the furniture door at 90 Insert the small square B into guide A Put together the appliance door and the furniture door and mark the holes as indicated in the figure Remove the squares and drill holes with 2 mm at 8 mm from the outer edge of the door Place the small square on the guide again and fix it with the screws supplied PR168 9 Should the lining up of the furniture door be necessary use the clearance of slots At the end of operations it is necessary to check if the door of the furniture closes properly 10 Fix cover D on guide B until it clips into place 15 2 From the Electrolux Group The world s No 1 choice The Electrolux Group is the world s largest producer of powered appliances for kitchen cleaning and outdoor use More than 55 million Electrolux Group products such as refrigerators cookers washing machines vacuum cleaners chain saws and lawn mowers are sold each year to a value of approx USD 14 billion in more than 150 countries around the world Electrolux plc 2004
4. any containers with flammable materials such as spray cans fire extinguisher refill cartridges etc in the refrigerator Maintenance and Cleaning e Before cleaning always switch off the appliance and disconnect from the electrical supply e When unplugging always pull the plug from the mains socket do not pull on the cable Servicing This product should be serviced by an authorised engineer and only genuine spare parts should be used Under no circumstances should you attempt to repair the appliance yourself Repairs carried out by inexperienced persons may cause injury or serious malfunctioning Contact your local Service Force Centre At the end of the Appliance Life e When disposing of your appliance use an authorised disposal site e Remove the plug and ensure that any locks or catches are removed to prevent young children being trapped inside Contents Instructions for the User Important Safety Instructions 2 Operation 22 20 e656 bere thwe eee ee bs 4 Before use Setting the temperature 4 Fresh food refrigeration 000 00s 4 Bottle holder 022000 ee eee 4 The door shelves 000 c eee eee eee 5 Normal operating sounds 0 5 Health and safety guidelines 6 Defrosting 22 00 scceventivew ens eesiaewes 6 Maintenance and Cleaning 005 7 Internal cleaning Changing the light bulb 7 So
5. eplacement of any light bulbs or removable parts of glass or plastic Costs incurred for calls to put right an appliance which is improperly installed or calls to appliances outside the United Kingdom Appliances found to be in use within a commercial environment plus those which are subject to rental agreements Products of Zanussi manufacture which are not marketed by Zanussi European Guarantee If you should move to another country within Europe then your guarantee moves with you to your new home subject to the following qualifications The guarantee starts from the date you first purchased your product The guarantee is for the same period and to the same extent for labour and parts as exists in the new country of use for this brand or range of products This guarantee relates to you and cannot be transferred to another user Your new home is within European Community EC or European Free Trade Area The product is installed and used in accordance with our instructions and is only used domestically i e a normal household The product is installed taking into account regulations in your new country Before you move please contact your nearest Customer Care centre listed below to give them details of your new home They will then ensure that the local Service Organisation is aware of your move and able to look after you and your appliance France Senlis 33 0 3 44 62 29 29 Germany Nurnberg 49 0 800 234 7378 Italy Porde
6. er to appliance Check there is power at the socket Check there is not a power cut by checking the household lights Check the fuse has not blown The light does not come on Ensure that the bulb is correctly fitted Replace the bulb if it has blown Check the door light switch is not jammed The temperature in the fridge or freezer section is too Check the ambient temperature is within the appliances high operating limits of 10 C to 38 C Check the thermostat control knob is turned to the correct setting relative to ambient conditions The compressor runs continuosly Adjust the thermostat control knob to give correct temperature control See page 4 Check that the door is closed Large quantities of food have recently been placed in the cabinet and or door is frequently opened Check that air ventilation is not obstructed Excessive frost and ice has built up Ensure the door is not left open Check that nothing is preventing the door from closing Is the door gasket intact and clean Noise Refer to normal operating sounds Water under the salad bins Check the drain hole is not blocked see Maintenance and Cleaning If after the above checks there is still a fault call your local Service Force Centre In guarantee customers should ensure that the above checks have been made as the engineer will make a charge if the fault is not a mechanical or electrical breakdown Please note that proof of purchase is required f
7. event the hazard of shocks in case it should be plugged into a 13amp socket in another part of your home A Important The wires in the mains lead are coloured in accordance with the following code Green and Yellow Earth Blue Neutral Brown Live GREEN amp YELLOW 13 AMP FUSE CORD CLAMP If you fit your own plug the colours of the wires in the mains lead of your appliance may not correspond with the markings identifying the terminals in your plug proceed as follows Connect the Green and the Yellow earth wire to the terminal in the plug which is marked with the letter E or the earth symbol or coloured green and yellow Connect the blue neutral wire to the terminal in the plug which is marked with the letter N or coloured black Connect the brown live wire to the terminal in the plug which is marked with the letter L or coloured red The plug moulded onto the lead incorporates a fuse For replacement use a 13amp BS1362 fuse Only ASTA or BSI approved fuses should be used The plug must not be used if the fuse cover carrier is lost The cover carrier is indicated by the coloured insert at the base of the plug This appliance complies with the following E E C Directive C 73 23 EEC of 19 2 73 Low Voltage Directive and subsequent amendments 87 308 of 2 6 87 Radio Interference Suppression and subsequent amendments 89 336 EEC of 3 5 89 Electromagnetic Co
8. gerant isobutane R600a is contained within the refrigerant circuit of the appliance a natural gas with a high level of environmental compatibility which is nevertheless flammable During transportation and installation of the appliance be certain that none of the components of the refrigerant circuit become damaged If the refrigerant circuit should become damaged avoid open flames and sources of ignition thoroughly ventilate the room in which the appliance is situated Child Safety e Do not allow children to tamper with the controls or play with the product e There is a risk of suffocation Keep packaging material away from children General Safety This appliance contains hydrocarbons in its cooling unit maintenance and recharging must therefore only be carried out by authorised technicians Take utmost care when handling your appliance so as not to cause any damages to the cooling unit with consequent possible fluid leakages The appliance must not be located close to radiators or boilers Avoid prolonged exposure of the appliance to direct sunlight Do not use other electrical appliances such as ice cream makers inside of refrigerating appliances During Use This appliance is designed for domestic use only specifically for the storage of edible foodstuffs It is not intended for commercial or industrial use Containers with flammable gases or liquids can leak at low temperatures Do not store
9. he refrigerator are equipped with runners so that shelves can be positioned as desired For better use of space the front half shelves can lie over the rear ones see fig Bottle holder only for ZI 9225 e Place the bottles with the opening facing front in the pre positioned shelf If the shelf is positioned horizontally place only closed bottles e This bottle holder shelf can be tilted in order to store previously opened bottles To obtain this result pull the shelf up so it can rotate upwards and be placed on the next higher level The door shelves To permit storage of food packages of various sizes the central door shelf can be adjusted in height To do this proceed as figure For more thorough cleaning the top door shelf and the bottle shelf can be removed by pulling them in the director of the arrows then refitting them in position Normal operating sounds You may hear faint gurgling or bubbling sounds when the refrigerant is pumped through the coils or tubing at the rear to the cooling plate When the compressor is on the refrigerant is being pumped round and you will hear a whirring sound or pulsating noise from the compressor A thermostat controls the compressor and you will hear a faint click when the thermostat cuts in and out G Health and Safety Guidelines Because of consumer demand preservatives have been removed from many pre prepared fo
10. ing further changes Important Dea prolonged periods of abnormally hot weather if the thermostat is set on too high a number the cooling system may operate continuously and the fridge cooling plate may not defrost Turning the knob to a lower number will cause the automatic defrosting to resume If you wish to return to a lower temperature turn the thermostat knob to a higher number however you should turn the setting lower occasionally to allow automatic defrosting Fresh food refrigeration To obtain the best performance do not store warm food or evaporating liquids in the refrigerator do cover or wrap the food particularly if it has a strong flavour Do not cover the shelves with any protective material such as paper cardboard or plastic which may obstruct the air circulation through them To help you use your refrigerator correctly here are some more useful hints Raw meat beef pork lamb amp chicken or poultry wrap in polythene bags and place on top of the salad bin 4 Meat can only be stored safely in this way for one or two days at the most Fruit amp vegetables these should be thoroughly cleaned and placed in the bottom salad bin Butter amp cheese these should be placed in special airtight containers or wrapped in aluminium foil or polythene bags to exclude as much air as possible Milk bottles these should have a cap and should be stored in the bottle rack on the door The walls of t
11. lean the drain hole of the water trough at regular intervals and make sure that the drain hole is never obstructed so that the defrost water may flow freely Once or twice a year remove the ventilation gril and dust the air channels at the base of the appliance with a brush or vacuum cleaner You MUST ensure that the appliance is switched OFF An accumulation of dust will affect the performance of the appliance and cause excessive electricity consumption Changing the light bulb Should the interior light fail to work first switch off the appliance and disconnect from the electricity supply then replace the bulb as follows 1 Unscrew the light cover and then pull it outward by pressing as shown in the figure 2 Unscrew the bulb and replace it with a new 15 watt bulb available from your nearest Service Force Centre 3 Replace the light cover by sliding it into its original position and replacing the screw When the appliance is not in use When the appliance is not in use for long periods disconnect from the electricity supply empty all foods and clean the appliance leaving the door ajar to prevent unpleasant smells Something not Working Before contacting your local Service Force Centre check the following points IMPORTANT If you call out an engineer to a fault listed below or to repair a fault caused by incorrect use or installation a charge will be made even if the appliance is under guarantee No pow
12. mething not Working 0ee eee 8 Service and Spare Parts 00055 9 Customer Care Department 9 Guarantee Conditions 000 eee eee 10 Instructions for the Installer Technical specifications 11 Installation 2 0 eee 11 Positioning sarananira sadasa a Doe na R Ean 11 Door reversal 00000 cee eee eee 12 Electrical Connection 05 13 Building IN 2 22 0ce0cce recta vecenees cower 14 Operation Before use Remove all securing tapes Wash inside the appliance with lukewarm water and bicarbonate of soda 5 ml to 0 5 litre of water Do not use soap or detergent as the smell may linger Dry thoroughly Setting the temperature The temperature inside the refrigerator is regulated by a thermostat control knob with 6 temperature positions and one OFF O position Position 1 minimum coldness Position 6 maximum coldness Turn the thermostat control knob to the required position An intermediate position is usually the most suitable although the temperature will be affected by e Room temperature e How often the door is opened e How much food is stored e Position of the appliance In determining the correct temperature control setting all these factors have to be considered and some experimentation may be necessary When altering the temperature setting allow 24 hours for the temperature to stablise before mak
13. mpatibility Directive and subsequent amendments Please ensure that when the appliance is installed it is easily accessible for the engineer in the event of breakdown 13 Building in Dimensions of the recess ZI 9155 ZI 9225 Height of housing 1 mm 880 1225 Depth of housing 2 mm 550 550 Width of housing 3 mm 560 560 S oh 32 PRO a It is necessary that the cabinet has a ventilation recess with the following dimensions Width 540mm Depth 50mm For appropriate venting follow indications in the figure 1 Push the appliance into the housing until stop strip touches the kitchen unit 14 2 Press in the joint covers between the appliance and the kitchen furniture 3 Open the door and push the appliance against the side of kitchen furniture opposite to that of appliance hinges Fasten the appliance with 4 screws l provided in the kit included with the appliance 4 Snap vent gril B and hinge cover E into position Apply blanking covers C D as indicated 5 Separate parts A B C D as shown in the figure 6 Place guide A on the inside part of the furniture door up and down as shown in the figure and mark the position of external holes After having drilled holes fix the guide with
14. ne at the address below or visit our website at www zanussi co uk Customer Care Department Zanussi 55 77 High Street Slough Berkshire SL1 1DZ 08705 727727 calls to this number may be recorded for training purposes Guarantee Conditions Standard guarantee conditions We Zanussi undertake that if within 24 months of the date of purchase this Zanussi appliance or any part thereof is proved to be defective by reason only of faulty workmanship or materials we will at our option repair or replace the same FREE OF CHARGE for labour materials or carriage on condition that The appliance has been correctly installed and used only on the electricity supply stated on the rating plate The appliance has been used for normal domestic purposes only and in accordance with the manufacturer s instructions The appliance has not been serviced maintained repaired taken apart or tampered with by any person not authorised by us All service work under this guarantee must be undertaken by a Service Force Centre Any appliance or defective part replaced shall become the Company s property This guarantee is in addition to your statutory and other legal rights Home visits are made between 8 30am and 5 30pm Monday to Friday Visits may be available outside these hours in which case a premium will be charged Exclusions This guarantee does not cover Damage or calls resulting from transportation improper use or neglect the r
15. none 39 0 0434 39 4700 Sweden Stockholm 46 0 8 672 53 90 UK Slough 44 0 1753 219897 Ireland Dublin 353 0 1 4090751 10 Technical specifications POWER SUPPLY VOLTAGE AND FREQUENCY TOTAL POWER ABSORBED AVERAGE DAILY UNITS ELECTRICITY GROSS CAPACITY NET CAPACITY ZI 9155 ZI 9225 220 240 V 50 Hz 220 240 V 50 Hz 100 W 140 W 0 49 kWh 0 53 kWh 158 230 154 228 This figure is based on standard test results in accordance with European Standard EN153 Actual consumption will depend on how the appliance is used and where it is located Installation Warning IF YOU ARE DISCARDING AN OLD APPLIANCE THAT HAS A LOCK OR CATCH ON THE DOOR YOU MUST ENSURE THAT IT IS MADE UNUSABLE TO PREVENT YOUNG CHILDREN BEING TRAPPED INSIDE Depending upon the position which you choose for your appliance you may wish to reverse the way in which the door opens To do this refer to instructions under Door reversal Positioning The appliance should only be installed at a location where the ambient temperature corresponds to the climate classification indicated on the rating plate which is located on the inside left of the appliance The following table shows which ambient temperature is correct for each climate classification SN 10 C to 32 C ST 18 C to 38 C The appliance should be located in a dry atmosphere out of direct sunlight and away from continuous heat and extreme temperature e g
16. ods This together with the changes in shopping habits to a once a week shop mean that safe handling and storage of food is even more important than ever The following tips should help you to ensure that the food in your home is in as perfect condition as possible e Keep the time between buying chilled food and placing it in your fridge as short as possible Tests showed that the temperature of 1 litre of orange juice rose to 22 C in an hour between the supermarket and home It then took 11 hours to get down to 7 C in the refrigerator Keep the refrigerator door closed as much as possible Do not push food together too much try to allow air to circulate around each item Cool cooked food as quickly as possible but do NOT place in the refrigerator until cool Leave food in a cool place in order that it can then be placed in the refrigerator as soon as possible Do NOT mix raw and cooked meat they must be in separate containers Take care not to let the meat juices drip onto other food If the meat does drip remove everything and clean thoroughly Do not store food uncovered Remove suspect food from your refrigerator and clean the interior see Maintenance and Cleaning Never allow spillages to dry and harden Store eggs in the egg rack provided in the refrigerator door Discard any broken or chipped eggs Regularly check the refrigerator door seal to ensure that it is clean and free from debris Alway
17. or any in guarantee service calls Service and Spare Parts SERVICE OFORCE In the event of your appliance requiring service or if you wish to purchase spare parts please contact your local Service Force Centre by telephoning 08705 929929 Your telephone call will be automatically routed to the Service Force Centre covering your post code area For the address of your local Service Force Centre and further information about Service Force please visit the website at www serviceforce co uk Before calling out an engineer please ensure you have read the details under the heading Something Not Working When you contact the Service Force Centre you will need to give the following details 1 Your name address and post code 2 Your telephone number 3 Clear and concise details of the fault 4 The model and serial number of the appliance found on the rating plate 5 The purchase date Please note that a valid purchase receipt or guarantee documentation is required for in guarantee service calls For Customer Service in Ireland please contact us at the address below Zanussi Electrolux Group Irl Ltd Long Mile Road Dublin 12 Republic of Ireland Tel 353 1 4090751 Email service eid electrolux ie Customer Care Department For general enquiries concerning your Zanussi appliance or for further information on Zanussi products please contact our Customer Care Department by letter or telepho
18. s wash your hands with soapy water and dry them with a clean towel before handling food Keep work surfaces clean and avoid cross contamination by not using the same work surface or knife without washing them thoroughly in between Defrosting The refrigerator automatically defrosts every time the compressor stops The water is discharged via the pipe into a tray located at the back of the appliance above the compressor where it evaporates A Important To avoid defrost water overflowing into the fridge periodically clean the water discharge hole in the centre of the V shaped drip collector at the back of the refrigerator compartment behind the salad bin Use the special cleaner provided which you will find already inserted into the discharge hole Maintenance and Cleanin Warning AN any maintenance or cleaning work is carried out DISCONNECT the appliance from the ELECTRICITY supply Important AL This appliance contains hydrocarbons in its cooling unit maintenance and recharging must therefore only be carried out by authorised technicians Internal cleaning Clean the inside and accessories with warm water and bicarbonate of soda 5ml to 0 5 litre of water Rinse and dry thoroughly NEVER USE DETERGENTS ABRASIVE POWDERS HIGHLY PERFUMED CLEANING PRODUCTS OR WAX POLISHES TO CLEAN THE INTERIOR AS THESE WILL DAMAGE THE SURFACE AND LEAVE A STRONG SMELL Important Do not use abrasive products C
Download Pdf Manuals
Related Search