Eureka Sanitaire Commercial SC888 Bagged Upright Vacuum
Contents
1. You will find the nearest location in the Yellow Pages under Vacuum Cleaners Service and Repair Be certain that the Warranty Station is Eureka Sanitaire Authorized For the location of the nearest Eureka Sanitaire Authorized Warranty Station or for service information telephone toll free USA 1 800 282 2886 Mexico 5670 6169 Canada 1 800 282 2886 If you prefer you can write to In Canada write to The Eureka Company The Eureka Company Service Division 866 Langs Drive 807 North Main Street Cambridge Ontario N3H 2N7 Bloomington IL 61701 USA If it is necessary to ship the cleaner outside your community to obtain warranty repair you must pay the shipping charges to the Eureka Sanitaire Authorized Warranty Station Return shipping charges will be paid by the Warranty Station When returning parts for repair please include the model type and serial numbers from the data plate on the cleaner FURTHER LIMITATIONS AND EXCLUSIONS Any warranty that may be implied in connection with your purchase or use of the cleaner including any warranty of MERCHANTABILITY or any warranty for FITNESS FOR A PARTICULAR PURPOSE is limited to the duration of this warranty Some states do not allow limitations on how long an implied warranty lasts so the above limitations may not apply to you Your relief for the breach of this warranty is limited to the relief expressly provided above IN NO EVENT SHALL EUREKA BE LIABLE FOR ANY CONSEQUE2. been dropped damaged left outdoors or dropped into water return it to a service center before using Do not pull or carry by cord use cord as a handle close door on cord or pull cord around sharp edges or corners Do not run vacuum cleaner over cord Keep cord away from heated surfaces Connect to a properly grounded outlet only refer to Grounding Instructions Do not use extension cords or outlets with inadequate current carrying capacity Turn off all controls before unplugging Do not unplug by pulling on cord To unplug grasp the plug not the cord Do not handle plug or vacuum cleaner with wet hands Do not put any object into openings Do not use with any opening blocked keep free of dust lint hair and anything that may reduce airflow This vacuum cleaner creates suction and contains a revolving brush roll Keep hair loose clothing fingers and all parts of body away from openings and moving parts Do not pick up anything that is burning or smoking such as cigarettes matches or hot ashes Do not use without dust bag in place Belt pulleys can become hot during normal use To prevent burns avoid touching the belt pulley when servicing the drive belt Use extra care when cleaning on stairs Do not use to pick up flammable or combustible liquids such as gasoline or use in areas where they may be present Store your cleaner indoors in a cool dry area Keep your work area well lighted Unplug electrical app
3. on the bag should be down and the bag should remain right side out Use warm water 150 F 65 C and a mild detergent Pre soaking the bag in a laundry pre soak is desirable for best cleaning results Air dry thoroughly before using DO NOT USE AN AUTOMATIC WASHER OR DRYER as either will cause abrasion to the delicate polyester fabric DO NOT DRY CLEAN as dry cleaning fluids will damage plastic parts of your bag assembly 11 Brush Roll Belt The brush roll belt on the upright vacuum cleaner drives the brush to agitate sweep and comb the carpet nap The belt should be checked regularly to be sure it is in good condition Replace the belt if it is stretching cracking or slipping Cut away any hair or thread wound around the brush roll or the belt pulley because the buildup could cause the belt to rotate unevenly How to Replace A Worn Belt NOTE Turn off the switch and unplug the electrical cord before replacing belt Belt pulleys can become hot during normal use To prevent burns avoid touching the belt pulley when servicing the drive belt IMPORTANT Improper installation of the brush roll or brush roll belt could cause carpet or cleaner damage 1 2 Release cam locks to remove bottom plate Pull up on belt to rotate it off the motor pulley Lift up on brush roll and remove worn belt ok 6 i i I i Place rubber end cap covers over both end caps flat side against end cap Align h
4. over the motor pulley Hold the fan blades with one hand and turn the wrench counterclockwise Remove the motor pulley and lift the fan off the motor shaft Clean the area and replace the fan over the motor shaft Tighten the motor pulley snugly clockwise with the wrench If necessary replace the fan cover or the gasket with replacement parts Be sure the gasket is in place Reposition the fan cover by first placing the exhaust end into place between the large rear wheels Seat the fan cover firmly Next replace the belt and bottom plate as the pressure from the bottom plate helps seal the fan cover Start the two screws by hand to be sure they are straight then tighten Order fan chamber cover replacement kit fan cover gasket two screws Part No 52334 Cleaner Care NOTE Turn off the switch and unplug the electrical cord before cleaning unit To keep the vacuum cleaner looking new it can be wiped with a damp cloth and a mild soap solution then thoroughly dried Never use any type of chemical as chemicals can damage the cleaner When not in use the cleaner should be stored in a clean dry place 10 HOW TO MAINTAIN The instructions given in this booklet serve as a guide to routine maintenance To avoid unnecessary service calls check the bag belt and brush roll often Disposable Dust Bags Paper bags play a very important role in the efficiency of a vacuum cleaner The purpose of a paper bag is to trap dirt But at the same
5. time the paper bag must be porous enough to allow air to pass through If the paper bag becomes clogged no air can pass through the cleaner and no cleaning can take place regardless of how powerful the unit Change the dust bag frequently Some fine particles can restrict airflow very quickly and will decrease performance even before the bag appears to be full For that reason when vacuuming carpet fresheners or cleaners powder plaster dust or similar fine substances the bag may need to be changed more often How To Change Disposable Dust Bag Style F amp G NOTE Turn off the switch and unplug the electrical cord before changing dust bag Never operate the vacuum cleaner without the dust bag 1 Pull zipper down spring j 3 Pull bag A as throat off s Bee a sleeve a 4 5 Place bag k NV throat on Z sleeve 6 Roll up coil spring 7 Place paper bag into outer bag NOTE Be certain there are no Look for the Eureka prooucr symbol folds at the top or bottom of the paper bag Ask for GENUINE EUREKA 8 Lift zipper dust bags Style F amp G Micron Filter Bag Care Micron Filter Bag is standard on some models Because the Micron Filter Bag is an effective filter medium occasionally trapped dust particles will need to be cleaned from the inside of it The dust accumulation can be vacuumed out with another vacuum or the bag may be removed to shake out If you desire the bag may be hand laundered The zipper
6. together so the handle bolt holes align and the slots in the handle are positioned as shown in Detail A Insert a 2 part bolt A in the center of the handle and tighten Hold the assembled handle so it curves away from the cleaner Then push the handle into the handle socket D at the rear of the cleaner Align the holes insert the other 2 part bolt A and tighten Step 2 Attach Upper Cord Hook Pull the spring on the electrical cord upward toward the top of the handle Make sure slots in handle are positioned B properly see below 1 Pl i tab 2 P he k 3 SNAP ite i BAG Place inner ta Press hoo opposite inner into slot around handle tab into place o Insert the lower half of the spring into the upper cord hook B as shown Snap the hook into the upper handle directions below ON Step 3 Attach Lower Cord Hook Make sure cord hook is pointing downwards Press the power cord into the groove on the cord hook pulling any slack toward the base of the cleaner On the cord hook find the curved tab and place in slot on lower handle section keep cord tau while pressing the cord hook to the left until it snaps into slot on opposite side of handle The hook should point downward on the same side that the cord exits the hood Step 4 Attach Outer Bag Important To provide a good gasket seal the bag coupling must seat firmly against the motor base Hold outer bag with zipper away from the handle Li
7. NTIAL OR INCIDENTAL DAMAGES THAT YOU MAY INCUR IN CONNECTION WITH YOUR PURCHASE OR USE OF THE CLEANER Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation or exclusion may not apply to you This warranty gives you specific legal rights You may also have other rights which vary by State PN Ta BS Can 2 gt P oaii tait e THE EUREKA COMPANY Bloomington Illinois 61701 2003 White Consolidated Ltd Part No 72936 03 03 Printed in U S A
8. Sanitaire QUICK KLEEN COMMERCIAL UPRIGHT VACUUM CLEANER OWNER S GUIDE 800 SERIES Index Important Safeguards General Information Dust Bag Brush Roll Belt Brush Roll chrome steel AN Brush Roll anodized aluminum Headlight NE Warranty I Rating Plate The model type and serial numbers are MODEL yee SERIAL indicated on the rating plate located on the underneath side of the cleaner For prompt and VOLTS AMPS HERTZ complete service information always refer to SERVICE INFORMATION 1 800 282 2886 these numbers when inquiring about service Model amp Type Serial No For location of nearest Eureka Sanitaire Warranty Station or service information call 1 800 282 2886 www eureka com IMPORTANT SAFEGUARDS When using an electrical appliance basic precautions should always be followed including the following READ ALL INSTRUCTIONS BEFORE USING THIS VACUUM CLEANER WARNING To reduce the risk of fire electric shock or injury Do not use outdoors or on wet surfaces Do not leave vacuum cleaner when plugged in Turn off the switch and unplug the electrical cord when not in use and before servicing Do not allow to be used as a toy Close attention is necessary when used by or near children Use only as described in this manual Use only manufacturers recommended attachments Do not use with damaged cord or plug If vacuum cleaner is not working as it should has
9. Use 25 watt replacement bulb only Ask for GENUINE EUREKA replacement bulb 40009A 14 THE SANITAIRE COMMERCIAL LIMITED WARRANTY WHAT THIS WARRANTY COVERS Your Sanitaire commercial cleaner is warranted to be free from all defects in material and workmanship in normal use FOR A PERIOD OF ONE YEAR The warranty is granted only to the original purchaser of the cleaner The warranty is subject to the following provisions WHAT THIS WARRANTY DOES NOT COVER e Parts of the cleaner that require replacement under normal use such as bumpers bags bristle strips belts light bulbs hoses impellers outer bags and cleaning e Damages or malfunctions caused by negligence abuse or use not in accordance with the Owner s Guide e Defects or damages caused by unauthorized service or the use of other than Genuine Eureka parts WHAT THE EUREKA COMPANY WILL DO The Eureka Company will at its option repair or replace a defective cleaner or cleaner part that is covered by this warranty As a matter of warranty policy the Eureka Company will not refund the consumer s purchase price WARRANTY REGISTRATION Please fill out and return the warranty registration card accompanying your cleaner continued on reverse side OBTAINING WARRANTY SERVICE To obtain warranty service you must return the defective cleaner or cleaner part along with proof of purchase to any Eureka Sanitaire Authorized Warranty Station
10. cap cover from F Slide in new brush strip of same length one end rounded end first Fit track on either B Unscrew locknut side into brush roll slot C Remove end cap Replace second brush strip from sleeve bearing brush roll opposite end of brush roll assembly includes a shaft washer E Replace shaft not pictured D Align indentation on bearing retainer D Remove bearing retainer with brush strip on both ends of brush E Push shaft through opposite end roll F Pull out worn brush strip with pliers replace shaft washer on sleeve bearing assembly C Position end cap with flat sides of center hole over flat sides of threaded shaft B Tighten locknut A Align holes and secure rubber end cap cover flat side against end cap When properly assembled the brush roll should rotate freely between the two end caps Check the condition of the belt change if necessary Replace the brush roll belt and bottom plate see How To Replace A Worn Belt Ask for GENUINE EUREKA replacement brush sirip 12 inch No 52282 16 inch No 52246 1 13 How To Replace Worn Brush Strips anodized aluminum spiral New brush strip inserts are supplied in sets of two one long and one short To replace remove bottom plate and belt see How To Change Belt Then grasp center of brush roll and lift to remove A Remove rubber end cap cover from one end Unscrew locknut Remove end cap Press down on the brush strip and push out Slide in new brush str
11. cordon en guise de poign e Ne pas fermer une porte sur le cordon ou tirer le cordon sur des coins ou bordures pointus Ne pas circuler sur le cordon avec l aspirateur Tenir le cordon a distance des surfaces chauffantes Branchez toujours l aspirateur dans une prise trois mise la terre Ne pas utiliser des rallonges ou des prises qui n ont pas de capacit suffisante pour transporter le courant Fermer tous les contr les avant d brancher Ne pas d brancher en tirant sur le cordon Pour d brancher tenez la fiche et non le cordon Ne pas manipuler la fiche ou l aspirateur avec les mains mouill es Ne pas rien ins rer dans les ouvertures Ne pas utiliser si des ouvertures sont bloqu es assurez vous qu elles soient d gag es de poussi re mousse cheveux ou toute autre chose qui pourrait r duire le passage de l air Cet aspirateur cr e de la succion et contient un rouleau brosse tournant Tenir les parties mobiles et les ouvertures loin des cheveux du linge des doigts et de toute partie du corps Ne pas ramasser des objets qui br lent ou fument comme les cigarettes alumettes ou cendres chaudes N utilisez pas sans le sac de poussi re en place Les poulies du courroie peuvent devenir chaudes pendant l utilisation normale Pour prevenir des br lures vitez de touch la poulie du courroie lorsque vous r parez la courroie Portez une attention particuli re lorsque vous nettoyez les escaliers Ne pas u
12. cuit de 120 V et est muni d une fiche de mise la terre semblable celle illustr e par le Figure A S assurer que l appareil est branch une prise de courant ayant la m me configuration que la fiche Aucun adaptateur ne devrait tre utilis avec cet appareil Bo te de Prise de Terre o LA LAME DE TERRE EST LA PLUS LONGUE FIGURE A DES TROIS LAMES GENERAL INFORMATION The cleaner is designed to pick up dirt and dust particles Avoid picking up hard or sharp objects with the cleaner to prevent bag tears hose clogs and fan blade breakage with subsequent motor damage Service Information The instructions in this booklet serve as a guide to routine maintenance For additional service information telephone our toll free number for the nearest Eureka Sanitaire Authorized Warranty Station Refer to The Sanitaire Commercial Warranty for complete service information You should know the model type and serial numbers when you call USA 1 800 282 2886 Mexico 5670 6169 Canada 1 800 282 2886 DO NOT OIL the motor or the brush roll at any time The bearings are permanently lubricated and sealed Assembly Packet is with owner s guide 99 mu a ms B A C 2 Part Cord Bag Bolt Hooks Screws HOW TO ASSEMBLE The assembly packet contains two 2 part bolts 2 bag screws and two cord hooks An extra drive belt is also included with some models Step 1 Assemble the Handle Slip the upper handle and the lower handle
13. dd to the cleaning efficiency of the cleaner To operate simply run cleaner along edge board Edge Kleener operates instantly and automatically Cleaner Height Setting WARNING Avoid injury Keep loose clothing hair fingers and all other parts of body away from any moving part such as the revolving brush Turn off the switch and unplug the cleaner before changing the cleaner height setting Adjust the vacuum cleaner height setting to match the carpet pile height Refer to the following chart of recommended settings for carpet types The front of the cleaner has either a knob or slide adjustment which raises or lowers the cleaner base to match the type of carpet With the cleaner cord unplugged set the adjustment according to the table as a starting point While the cleaner is off and disconnected from the outlet place the handle in the operating position tilt the cleaner back to remove the weight Recommended Setting Example of Carpet Position 1_oayynyrm__Low pile as kitchen indoor outdoor Position 2 __ lil Sculptured Position 3 MWWL _ Plush or thick sculptured Position 4 WUWA Thick plush If the cleaner has additional height settings they are for thicker carpets or where easier pushing is desired from the wheels and adjust the setting Then plug the cleaner into the electrical outlet turn on the switch lower the handle and pass the cleaner over the carpet If the cleaner is still difficult t
14. henever the adapter is used it must be held in place by a metal screw NOTE In Canada the use of a temporary adapter is not permitted by the Canadian Electrical Code GROUNDED GROUNDED OUTLET BOX OUTLET BOX ADAPTER GROUNDING BLADE FIGURE A IS LONGEST OF THE METAL THREE BLADES SCREW FIGURE B a G D OUNDING TAB CONSEILS DE SECURITE Lors de l utilisation d un appareil lectrique quelques pr cautions l mentaires doivent tre observ es incluant les suivantes LISEZ TOUTES LES INSTRUCTIONS AVANT D UTILISER VOTRE ASPIRATEUR AVERTISSEMENT Pour r duire le risque de feu de choc lectrique ou de blessure Ne pas utiliser l ext rieur ou sur des surfaces mouill es Fermez le commutateur et d branchez l appareil lorsque vous ne l utilisez pas ou avant le nettoyage ou l entretien Ne permettez pas qu il soit utilis comme jouet Une attention particuli re est n cessaire lorsque utilis par ou pr s d un enfant Suivez les recommandations d utilisation de ce manuel Utilisez uniquement les accessoires recommand s par le fabriquant Ne pas utiliser si le cordon ou la fiche sont endommag s Si l aspirateur ne fonctionne pas comme il le devrait s il a t chapp s il est endommag s il a t laiss a l ext rieur ou chapp dans l eau retournez le un centre de service avant de utiliser Ne pas le tirer ou le transporter par le cordon ne pas utiliser le
15. ip of same length clip first until clip locks into place Replace second strip from opposite end double bristle brush roll requires two sets of brush strips C Position end cap so flat side of center hole is over flat side of threaded shaft B Tighten locknut A Align holes and secure rubber end cap cover flat side against end cap Dow NOTE Some models have two rows of bristles When properly assembled the brush roll should rotate freely between the two end caps Check the condition of the belt change if necessary Replace the brush roll belt and bottom plate see How To Replace A Worn Belt Ask for Genuine Eureka replacement brush strip 12 inch No 52140 16 inch No 52264 Order two sets for double bristle brush rolls Headlight Bulb Standard on most models NOTE Turn off the switch and unplug the electrical cord before replacing headlight bulb Headlight style varies by model Locate the notches that release the tabs at either 1 top 2 side or 3 bottom of the lens as illustrated Place a screwdriver into one notch twist or pry the screwdriver to release the lens Repeat for the second notch on the opposite side Rotate the bulb socket forward Push bulb in and turn to remove Secure new bulb into socket and rotate bulb socket backward Replace the lens tabs into the top or the bottom of the hood opening Rotate lens to position and press down at each notch until the lens locks into position NOTE
16. liances before vacuuming them SAVE THESE INSTRUCTIONS Grounding Instructions This appliance must be grounded If it should malfunction or breakdown grounding provides a path of least resistance for electric current to reduce the risk of electric shock This appliance is equipped with a cord having an equipment grounding conductor and grounding plug The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances DANGER Improper connection of an equipment grounding conductor can result in risk of electric shock Check with a qualified electrician or service person if you are in doubt as to whether the outlet is properly grounded Do not modify the plug provided with the appliance If it will not fit the outlet have proper outlet installed by a qualified technician This appliance is for use on a nominal 120 volt circuit and has a grounding plug that looks like the plug illustrated in Figure A A temporary adapter which looks like the adapter illustrated in Figure B may be used to connect this plug to a two pole receptacle as shown if a properly grounded outlet is not available The temporary adapter should be used only until a properly grounded outlet Figure A can be installed by a qualified electrician The green colored rigid ear lug or the like extending from the adapter must be connected to a permanent ground such as a properly grounded outlet box cover W
17. ne up screw holes Start the bag screws by hand then tighten with a screwdriver Loop the bag spring onto the bag support hook located at the back of the upper cord hook HOW TO ASSEMBLE continued Step 5 Store Electrical Cord The cleaner has two convenient cord storage hooks attached to the handle Wind the cord around the hooks and fasten the plug to the cord to prevent unwinding HOW TO USE The upright vacuum cleaner is designed to be used on multiple types of carpeting Do not attempt to use the upright vacuum cleaner on bare floors as damage to the floor covering may result Above the floor cleaning tools are available optional Handle Adjustment With the tip of the foot press down to release the handle lock located at the left rear side of the cleaner Move the handle and adjust it to the desired position for 1 storing upright 2 operating the cleaner at a comfortable height for the user and 3 cleaning underneath low furniture Underneath EL Handle Lock Power Switch awore 1 The power switch is mounted on the motor hood near the handle Switch style varies by model and may differ from the illustration A push with the foot turns the motor ON push again to turn the motor OFF oe Edge Kleener Edge Kleener feature provides for improved cleaning of carpets near walls and stationary furniture Slots on the sides of the nozzle increase air flow to the edges of the cleaner and a
18. o push follow the procedure and test the cleaner at the next higher setting Continue testing the setting until the cleaner is comfortable to move Moving the knob or slide to the next higher setting raises the brush roll slightly making the cleaner easier to push However the brush roll must make contact with the carpet for effective cleaning HOW TO MAINTAIN The instructions given in this booklet serve as a guide to routine maintenance To avoid unnecessary service calls check the bag belt and brush roll often Quick Kleen Fan Chamber NOTE Turn off the switch and unplug the electrical cord before cleaning The clear removable fan chamber cover provides easy inspection cleaning and maintenance of the fan chamber Removing the cover provides easy access to the motor fan Grease buildup dirt or other obstructions visible through the fan cover should be removed To clean the fan area take off the chrome bottom plate by releasing the two cam locks see Brush Roll Belt Figure 1 and 2 Remove the belt from the motor pulley then loosen and remove the screws on either side of the fan cover as indicated by the arrows Push the cam locks outward against the wheels to lift the cover from the cleaner base Dirt and obstructions can easily be cleared however caked grease may need to be scraped from the cover and the cleaner If the fan does not turn freely it also should be removed for cleaning To remove the fan place a wrench
19. oles and secure Align end caps with slots in cleaner base Push brush roll into base Ask for GENUINE EUREKA replacement belts No 52100 GENUINE Look for the LI symbol 12 Brush Roll Pulley Check for brush wear see Brush Roll instructions Place new belt around brush roll Align brush roll pulley with belt guide Place lower side of belt into belt guide and pull to stretch the belt around the left side of motor pulley Rotate pulley to secure belt into groove Place slots of bottom plate over tabs of cleaner base Seat and secure cam locks refer to 1 Brush Roll The rotating brush roll sweeps and combs the carpet nap Keep the brush roll free from hair and threads so it will continue brushing the carpet nap Replace worn brush strips when the bristles no longer touch a piece of cardboard held across the bottom plate There are two types of brush rolls the chromed steel tubular brush roll or the anodized aluminum spiral brush roll Follow the instructions for the type of brush roll featured on the cleaner NOTE Turn off the switch and unplug the electrical cord before replacing brush strips How To Replace Worn Brush Strips chromed steel tubular New brush strips are supplied in sets of two one long and one short To replace remove bottom plate and belt see How To Change Belt Then grasp center of brush roll and lift to remove A Remove rubber end
20. tiliser pour ramasser des liquides inflammables ou combustibles comme de l essence Ne pas utiliser dans les endroits o ces liquides pourraient tre pr sents Entreposez votre aspirateur l int rieur dans un endroit propre et sec Maintenez un bon clairage l endroit o vous travaillez D brancher les appareils lectrique avant de les balayer CONSERVEZ CES INSTRUCTIONS INSTRUCTIONS VISANT LA MISE A LA TERRE Cet appareil doit tre mis la terre En cas d faillance ou de panne ventuelles la mise a la terre fournit au courant un chemin de moindre r sistance qui r duit le risque de choc lectrique Cet appareil est pourvu d un cordon muni d un conducteur de terre et d une fiche avec broche de terre La fiche doit tre branch e dans une prise appropri e correctement install e et mise la terre conform ment aux r glements et ordonnances municipaux AVERTISSEMENT Un conducteur de terre mal raccord peut entra ner un risque de choc lectrique Consulter un lectricien ou un technicien d entretien qualifi si vous n tes pas certain que la prise est correctement mise la terre Ne pas modifier la fiche fournie avec l appareil si elle ne peut tre ins r e dans la prise faire installer une prise ad quate par un lectricien qualifi Note Au Canada l utilisation d un adaptateur temporaire n est pas autoris e par le Code canadien de l lectricit Cet appareil est destin un cir
Download Pdf Manuals
Related Search