U-Line CLR2060 Stainless Steel Compact Refrigerator
Contents
1. 1 4 Space le Between Appliances LS Figure 11 02 2005 CLR2060 Clear Ice Maker 4 Prepare and Install Door Panel Black and White Units Only Two types of custom door panels can be installed on your Black or White unit to harmonize with or accent the surrounding d cor a Custom 1 4 Insert or a Full Overlay If no custom door panel is used go on to 5 Adjust Door Custom 1 4 Door Panel Insert Door Panel Preparation A custom door panel can be inserted into the doorframe Custom door panels can be flat or raised as long as the maximum panel thickness where inserted into the door reveal channel is 1 4 thick For raised panels the depth of the reveal is 1 4 on all four sides IMPORTANT Raised panels will reduce the door s 90 swing zero clearance if the unit is installed next to a wall or similar type of structure see Page 4 Cut the panel insert to the following dimensions Custom 1 4 Dimensions Width 14 1 32 Height 28 5 32 The door panel must not weigh more than 20 lbs Door Panel Installation Install the insert as follows CAUTION Use care when handling the insert Insert edges may be sharp 1 Remove top hinge screw pin 7 64 Allen wrench or Phillips screwdriver depending on your unit s construction see Figure 12 Remove door by tilting forward and lifting off bottom hinge pin 02 2005 Figure 12 10 U U LINE e2. 14 5 16 21 4 1 Install the assembled panel by sliding the original door panel back into the doorframe 2 Replace the two piece Modified Handle assembly and secure with the two screws removed in Step 5 under Removing Existing Door 1 1 32 3 Starting at the corners and working toward the center Figure 21 push the door gasket back into place i Installing the Door 4 Attach the door panel to the overlay panel using 10 x 9 5 8 wood screws and nylon spacers The nylon spacers 1 Remove the existing hinges from the unit saving the fit between the overlay panel and the door panel as door closure assembly shown in Figure 22 The spacers allow the original door panel to slide back into the 1 4 thick door reveal channel 2 Install the new Replacement Top Hinge onto the unit see Figure 24 www U LineService com 10 02 2005
3. or right hand hinged The Stainless doors are not reversible and do not accept custom panels CLR2060 Clear Ice Makers may be ordered with a factory installed drain pump Please carefully follow the directions that apply to your unit and your intended design Tools Materials Reguired 7 64 Allen wrench e Screwdrivers slotted and Phillips head e 1 4 inch OD copper tubing and shut off valve for water supply line e 5 8 inch ID drain line e P60 Drain Pump if required and not already factory installed see Page 12 e 1 4 inch thick door panel material and cutting tools Black or White units e Full Overlay Door Panel Kit part number U OL2015B Black or part number U OL2015W White 3 4 inch door panel overlay cutting tools drill and bits Black or White units Inspection Unwrap and inspect the unit on a flat level surface capable of supporting its entire weight www U LineService com UFLINE ecoRPORATION CLR2060 Clear Ice Maker 3 Prepare Site Product Dimensions Your U Line product has been designed for either free standing or built in installation When built in your unit does not reguire additional air space for top sides or rear However the front grille must NOT be obstructed and clearance is reguired for water drain and electrical connections in the rear Note Unit can NOT be installed behind a closed cabinet door Cut Out Dimensions See Electrical Specifications f
4. HAZARD Electrical Grounding Reguired e Keep the unit unplugged throughout installation except during testing Never remove the round grounding prong from the plug and never use a two prong grounding adapter e Never use an extension cord to connect power to the unit e Always keep your working area dry NCAUTION e Use care when moving and handling the unit Use gloves to prevent personal injury from sharp edges e Do not lift the unit by the door or door handle e Do not install the unit behind closed doors or in any way that would obstruct airflow to the front grille which may cause the unit to malfunction 02 2005 U U LINE ecoRPORATION 2 Inspect and Plan You have received a carton containing your CLR2060 Clear Ice Maker with a package inside containing a User Manual a Product Registration Card and water connection parts Complete and mail the Product Registration Card or register online at www U LineService com Once your unit is installed keep the User Manual and this Installation Guide in a safe place for future reference Your unit is Black White or Stainless Steel Black and White units have a reversible door with a slightly contoured handle across the top They come with a flush mounted door panel that when removed will accept a custom 1 4 inch thick door panel or a 3 4 inch thick full overlay door panel Stainless Steel units are covered with a protective coating and have been ordered left
5. Maker y UFLINE ecoRPORATION 4 Drill hole for upper door hinge top of panel see 4 Remove the top handle and discard This handle will be Figure 16 Top View replaced with the Modified Handle included in the Full 0 177 diameter Overlay Door Panel Kit 16 drill x 11 16 deep 5 Remove the two screws located on both sides of the lower handle Remove the handle 5 Drill hole for lower door hinge see Figure 16 Bottom View 6 Attach the Modified Handle to the lower handle using the three screws removed in Step 3 Set aside 5 16 diameter x 1 4 deep 7 Slide the existing door panel out of the doorframe NCAUTION Attaching the Full Overlay Panel It is mportant to ensure that all drilled holes are drilled to 1 Tap nylon inserts into the top holes drilled in the the correct depth in order to avoid splits in the wood overlay panel Use two 6 screws to attach top pivot when hardware is installed bracket to the overlay panel see Figure 19 Installation Instructions Typical Wood Removing Existing Door YP Banel 65 y 1 Remove top hinge screw pin 7 64 hex key or Phillips i 4 SS D screwdriver depending on your unit s construction 6 X 5 8 Remove the door by tilting forward and lifting off the bottom hinge pin id Top Pivot 2 Pull door gasket out of the groove top edge of door 8 mm Plug Insert only Start in the middle and pull outward moving Two Required toward the edge see Figure 1
6. 7 This may take some force Figure 19 2 Ifa user supplied cabinet handle will be used attach its hardware to the overlay panel at this time 9 3 Place and tape the existing door panel on the back of the overlay panel see Figure 20 and drill holes through both panels according to Figure 21 Remove tape adjoining the panels and enlarge the six holes in the overlay panel using a 0 201 7 drill Figure 17 Figure 18 3 Remove the three screws located on the back of the handle see Figure 18 02 2005 9 www U LineService com y UrLINE CLR2060 Clear Ice Maker ecoRPORATION Typical Door Panel Removed Wood Panel Door Panel Top 10 x 5 8 Round Head Screw Six Required Plastic Spacer Six Required Figure 22 Side of Wood Panel Bottom of Wood Panel 2 3 8 Both Sides 5 Remove the existing bottom pivot plate and replace Figure 20 with the Full Overlay pivot plate see Figure 23 Existing Door Wood Panel Bottom Pivot Plate _ 9 8 Longer Than Existing Bottom Pivot Plate 2 Existing Bottom Pivot Plate Remove and Discard Flush Side Facing Out Drill 5 32 3 8 Deep for use with 10 5 8 Wood Screw and Nylon Spacer 6 Places A 8 32 3 8 SEMS Hex Screw Two Places Figure 23 Rear view IMPORTANT 0 Wood Panel Door panel and overlay panel must be aligned properly or the door will not operate correctly Assembling the Door
7. U UFLINE C ORPORATION Echelon Series Installation Guide EE CLR2060 Clear ice Maker www U LineService com Phone 414 354 0300 FAX 414 354 7905 Service amp Parts Tech Lines Phone 800 779 2547 FAX 414 354 5696 OnlineService U Line com 2005 U Line Corporation 02 2005 U U LINE ecoRPORATION Contents Cut Out Dimensions Yg 4 Product Dimensions Y YY uu 4 Door Swing Clearances Information 4 ReversingtheDoor YY YY YG 5 Other Site Reguirements 6 Side By Side Installation Instructions 6 Custom 1 4 Door Panel Insert 7 Full Overlay Door Panel Y ud 8 Checking Door Alignment 11 Adjusting Door Alignment 11 Drain Connection YY Y Yg 12 Water Supply Connection 15 Electrical Specifications 16 Leveling Information uu 16 Installation Tip Y FF Y eee 17 Installation of the CLR2060 17 Installation Troubleshooting 18 Initial Start Up 2202022222 18 Start Up Troubleshooting 19 Service Information V YY eee 20 www U LineService com CLR2060 Clear Ice Maker 1 Follow Safety Precautions IMPORTANT PLEASE READ all instruction
8. coRPORATION Figure 13 Pull door gasket out of groove top edge of door only Start in the middle and pull outward moving toward the edge see Figure 13 This may take some force Do not remove the three screws behind gasket Remove two outside screws holding door handle Slightly separate door handle from door see Figure 14 Pull handle up and off Remove and discard existing panel Slide custom door panel insert into 1 4 inch channel in door front Holding door gasket out of the way replace handle on door making sure it is seated properly on insert and that screw holes line up Figure 14 Install two small screws removed in Step 3 Starting at the corners and working inward push door gasket into place on door Place door on bottom hinge pin and install upper hinge screw Go on to 5 Adjust Door www U LineService com UFLINE ecoRPORATION Full Overlay Door Panel Door Panel Preparation A full overlay door panel completely covers the doorframe and handle to give a built in appearance See your U Line dealer for the optional Full Overlay Door Panel Kit P N U OL2015B Black or P N U OL2015W White Appropriate hardware Modified Handle Replacement Hinges and a copy of these instructions will be included in the kit 1 Cut the overlay to the following dimensions see Figure 15 Full Overlay Dimensions Width 14 3 4 Height 29 7 8 The door panel must not weigh more t
9. door to allow the pivot pin to be inserted in the new location Install the plug into the vacated hole on the opposite side 7 With bottom of door facing up remove pivot plate 2 screws flip over and remount on opposite side of door see Figure 9 Be sure notch in plate faces center Figure 9 8 Holding door upright with top of door tilted forward place hole of door pivot plate on bottom hinge screw pin see Figure 10 9 Tilt top of door into position in top hinge and install top hinge screw pin 10 Install plastic screw plugs removed in Step 2 in old hinge holes 3 each top and bottom Figure 10 www U LineService com UFLINE ecoRPORATION Other Site Reguirements Power Supply The unit reguires a grounded and polarized 115 VAC 60 Hz 15A circuit normal household current See Electrical Specifications on Page 16 Water Supply The unit reguires a 1 4 inch OD water supply line and a shut off valve For more information see Page 15 The unit s generous 7 inch drain connection height extends the distance the unit can be located from a gravity drain For more information see Page 12 IMPORTANT Drain can NOT be located directly below unit Unit has a solid base that will not allow unit to drain below itself Environmental Reguirements The surrounding air temperature must be at least 50 F 10 C but must not exceed 110 F 40 C High ambient t
10. emperature ranges and warmer water supply will cause reduced ice production Black and White units may be installed outdoors in a covered area Stainless Steel CLR2060 units are deemed suitable for outdoor use by UL The unit must not be located near heat generating eguipment or in direct sunlight www U LineService com CLR2060 Clear Ice Maker Side By Side Installation Instructions For a complete refreshment center install your CLR2060 Clear Ice Maker beside a U line Refrigerator Combo or Wine Captain Model see Figure 11 for typical cut out Note that each Side By Side Installation will be different e Cut out width for a side by side installation is the total of the widths listed under Cut Out Dimensions in each unit s Installation Guide For example Placing a CLR2060 Clear Ice Maker next to a 2015R Refrigerator would reguire a cut out width of 15 3 16 15 3 16 30 3 8 Placing a CLR2060 Clear Ice Maker next to a 2075R Refrigerator would reguire a cut out width of 15 3 16 24 3 16 39 3 8 e No trim kit is required However 1 4 inch space needs to be maintained between the units to ensure unobstructed door swing e Units must operate from separate properly grounded electrical receptacles placed according to each unit s Electrical Specifications Typical Side By Side Cut Out Preferred Location Acceptable for CLR2060 Location Receptacle o a ia
11. han 20 lbs Relief Notch Rear View for Pivot Plate 0 Wood Panel Figure 15 IMPORTANT Rear View of wood panel for right hand hinge shown Use mirror image for left hand hinges 2 Create a relief Figure 15 for pivot plate by cutting notch in top corner and coinciding back corner of overlay panel Refer to Figure 16 for exact specifications www U LineService com CLR2060 Clear Ice Maker 13 32 0 0 177 Dia 16 Drill lt gt x 11 16 Deep Door Bottom 5 16 Dia x 1 4 Deep Chamfer 1 32 x 45 Bottom View 13 16 gt Top View 1 8 5 Y aet 1 17 32 UAN 7 16 o 7 5 16 Dia lt 13 16 gt 1 2 Deep e 3 4 gt Back View Side View Figure 16 Route notch in top corner of overlay panel as shown see Top and Side Views Top of notch is entire depth of panel front to back Width 13 16 Depth 1 8 Route notch in backside of top corner of overlay panel see Back and Side Views Width 13 16 Depth 1 8 Height 1 17 32 from top edge of panel less 1 8 for depth of notch on top of panel Radius of corner notch 1 8 see Back View 3 Drill holes for pivot plate mounts see Figure 16 Back View 5 16 diameter x 1 2 deep from the routed surface CAUTION Be careful not to drill too deep Drilling holes too deep may destroy your door panel 02 2005 CLR2060 Clear Ice
12. n lt oo ry 90 Door Swing Black and White Figure 3 Stainless Steel 02 2005 CLR2060 Clear Ice Maker Reversing the Door Black and White Units Only All U Line units except Stainless Steel models may be left or right hand opening The door opening is easily reversed by moving the hinge hardware to the opposite side The top hinge hardware will be used on the bottom of the other side and the bottom hinge hardware will be used on the top of the other side see Figure 4 To reverse the door 1 Remove top hinge screw pin from door 7 64 Allen wrench or Phillips screwdriver depending on your unit s construction see Figure 5 Remove door by tilting forward and lifting off bottom hinge pin Figure 4 2 Remove plastic screw plugs 3 each top and bottom from new hinge location Do not discard see Figure 6 Screw Plugs Figure 5 3 Remove top hinge 3 screws reinstall hinge screw pin and remount on opposite side BOTTOM see Figure 7 02 2005 y U LINE ecoRPORATION 4 Remove the two door closer inserts from the existing bottom hinge and install as shown on the new bottom hinge see Figure 8 Door Closer Inserts Figure 8 5 Remove existing bottom hinge 3 screws and remount on opposite side TOP Remove hinge screw pin 6 Remove the plastic hole plug from the top of the
13. or Power Supply t Figure 1 Follow the cut out drawing in Figure 1 The 15 3 16 width allows 1 4 for ease in installation and removal of the unit The 24 depth is the counter depth in most installations The unit is 24 deep including the handle on Black and White models and 24 deep including the door and not the handle on Stainless Steel models see Figure 2 IMPORTANT If you would like to align the face of the unit with other adjacent cabinet doors in certain installations you may need to alter the wall just behind the drain connection on the unit to accommodate the drain The actual amount of alteration will be determined by your actual drain connection components www U LineService com 24 26 1 8 Including en aa Including Handle 14 15 16 gt le 14 15 16 gt Black and White Stainless Steel Figure 2 Please note that the unit has adjustable feet that can add one additional inch to height during leveling or to match adjacent cabinets see Figure 44 on Page 17 Door Swing Clearances Information Black and White units have a zero clearance for the door to open 90 see Figure 3 Stainless Steel models require a minimum of 2 1 8 door clearance to accommodate the handle if the unit is installed next to a wall or similar type of structure Wall 2 1 8 Min c n i ry Walls MM 1 4 Mi
14. s completely before attempting to install or operate the unit e This unit requires connection to the water supply Improper hook up can result in substantial property damage If you are unsure of your ability to safely connect the water supply to the unit consult a licensed plumber for assistance This unit requires connection to a drain Improper connection can result in substantial property damage If you are unsure of your ability to safely connect the unit to a drain consult a licensed plumber for assistance This unit requires connection to a grounded three prong polarized receptacle that has been placed by a qualified electrician in accordance with applicable electrical codes Safety Alert Definitions Safety items throughout this guide are labeled with a Danger Warning or Caution based on the risk type AMDANGER Danger means that failure to follow this safety statement will result in severe personal injury or death NWARNING Warning means that failure to follow this safety statement could result in serious personal injury or death NCAUTION Caution means that failure to follow this safety statement may result in minor or moderate personal injury property or eguipment damage 02 2005 CLR2060 Clear Ice Maker General Precautions Use this appliance for its intended purpose only and follow these general precautions along with those listed throughout this guide NWARNING SHOCK
Download Pdf Manuals
Related Search