A-Trend ATC 6240 (ATC-6240) Motherboard - 6240V
Contents
1. Video This category selects the type of video adapter used for the primary system monitor Although secondary monitors are supported you do not have to select the type in Setup EGA VGA Enhanced Graphics Adapter Video Graphics Array For EGA VGA SEGA SVGA or PGA monitor adapters CGA 40 Color Graphics Adapters power up in 40 column mode CGA 80 Color Graphics Adapters power up in 80 column mode MONO Monochrome adapter includes high resolution monochrome adapters 20 ATC6240V Mainboard Chapter 3 Award BIOS Setup Halt On This category determines whether the computer will stop if an error is detected during power up The system boot will not be stopped for any error that may be detected you will be prompted Keyboard other errors Diskette errors Disk Key all other errors Memory This category is displayed only which is determined by POST Power On Self Test of the BIOS Base Memory The POST will determine the amount of base or conventional memory installed in the system The value of the base memory is typically 512K or 640K based on the memory installed on the motherboard Extended Memory How much extended memory is present during the POST This is the amount of memory located above 1MB in the CPU s memory address map Other Memory This refers to the memory located in the 640K to 1024K address space This is memory that can be used for different applications DOS uses this area to load device driv2. Clear CMOS io Normal Pin 1 2 closed Clear CMOS Pin 2 3 closed ISA Slots PCI Slot JP 8 Chapter 3 Award BIOS Setup ATC6240V Mainboard 3 1 UPDATE BIOS PROCEDURE If the BIOS needs to be updated you can get a CD or diskette with the updated BIOS utility in the package The BIOS update diskette or All In One CD includes two files awdflash exe and awdflash doc And the new or updated Award BIOS file should be obtained from your system manufacturer or dealer The updating procedure is as the following L Before updating your BIOS please load the above mentioned files to root directory C or a floppy drive diskette Boot the system to DOS mode in a normal manner Under C or Drive A where your BIOS update files should be type awdflash exe and press Enter The following screen will instantly appear on which you should enter the file name of the new or updated BIOS After you have entered the file name press Enter And on the Error Message row shows Do you want to save BIOS Y N Type N but do not press Enter And the message Are you sure to program Y N will appear at once Type Y but do not press Enter BIOS updating process will start at once until you see the message Reset System or power off to accomplish update process Press FI button to restart your system and the updating process is complete A
3. Password via Keyboard for setting the Password Power On function If a set password is forgotten or can not be retrieved please refer to Page 15 Clear CMOS to clear old password and set a new one gt Hot Key This is also an ATX Power supported function Please refer to Page 5 Hot Key via Keyboard for setting this Hot Key Power on function gt Mouse Left Mouse Right This is also an ATX Power supported function Please refer to Page 5 Mouse Left Mouse Right via PS 2 Mouse for setting this PS 2 Power on function When using this Power On function to shut or start your computer your double clicking the mouse button should not be interfered by any slight move or slide of the mouse gt BUTTON ONLY Only pressing power button can power the system KBC Input Clock Let user change the keyboard working clock On Board FDC Controller This item will enable or disable the floppy disk controller On Board Serial Port 1 User can select serial port IRQ If set to Auto system will assign an IRQ for it Note set to Auto is not recommended On Board Serial Port 2 User can select serial port IRQ If set to Auto system will assign an IRQ for it Note set to Auto is not recommended UART Mode Select This lets you select the Infrared mode Choices are Normal IrDA and ASKIR If you choose IrDA or ASKIR mode the screen will show another two lines to let you choose RxD TxD Active Hi Lo Lo Hi Hi Hi Lo Lo
4. and IR Transmission Delay Enabled Disabled On Board Parallel Port Let user select IRQ for parallel port When Disabled the parallel port will be disabled Parallel Port Mode Let user select parallel port protocol This item is not recommended to change except user has special request 35 Chapter 3 Award BIOS Setup ATC6240V Mainboard ECP Mode Use DMA Select a DMA channel for the port Choices are 3 1 EPP Mode Select Let user select EPP version PWRON After PWR Fail When you set Former State this allows you to set whether you want your system to boot up after the power has been interrupted Otherwise Off leaves your system off after reapplying power 36 ATC6240V Mainboard Chapter 3 Award BIOS Setup ROM PCI ISA BIOS CMOS SETUP UTILITY AWARD SOFTWARE INC STANDARD CMOS SETUP INTEGRATED PERIPHERALS BIOS FEATURES SETUP SUPERVISOR PASSWORD CHIPSET FEATURES SETUP USER PASSWORD POWER MANAGEMENT SETUP IDE HDD AUTO DETECTION PNP PCI CONFIGURATION SAVE amp EXIT SETUP LOAD BIOS DEFAULTS EXIT WITHOUT SAVING LOAD SETUP DEFAULTS ESC Quit AV gt Select Item F10 Save amp Exit Setup Shift F2 Change Color ROM PCI ISA BIOS CMOS SETUP UTILITY AWARD SOFTWARE INC Hard Disks Type Size CYLS HEAD PRECOMP LANDZ SECTOR MODE Primary Master Select Primary Master Option N Skip N Options Size CYLS Head PRECOMP LANDZ Sector Mode 2 Y 1337 648 64 0 2594 63 LBA 1 1339 2595 16 65535 2594 63 NORMAL
5. choose User Define or Min Power Saving or Max Power Saving in Power Manager and pick up Yes in PM Control by APM In Windows 95 98 if you would like to power off the system you just need to choose shutdown the computer in the Shut Down Windows from Windows 95 98 Then the system power will be off directly and become to the stand by status If you would like to restart the system just press the power switch button and the system will be powered on Note If you are going to leave your system idle for several days we suggest you use hardware power off to shutdown your system Status Power LED Light Turbo LED Light Software power off Flash JP5 pin1 2 Light off control Light off JP5 pin2 3 APM mode Light on Light on System running Light on Light on Under Software power off control the status of Power LED Light depends on the setting of JP5 If you set JP5 to pin1 2 position it is blinking Otherwise it is light off 1 3 2 Fan Off Control With fan off function the CPU cooling fan can turn off automatically even when the system is in suspend mode This function is able to reduce energy consumption and system noise Because it is a feature of advanced BIOS you should set this option enabled through Power Management Setup from the BIOS setup screen ATC6240V Mainboard Chapter 1 Introduction 1 3 3 Running 100 MHz CPU Bus with
6. the Processor Serial Number is detectable and can be utilized in information Management etc When Disabled the Processor Serial Number is not detectable This feature is built in Pentium III Processor only Quick Power On Self Test This category speeds up Power On Self Test after you power up the computer If you set Enabled BIOS will shorten or skip some items under check during POST Boot Sequence This category determines which drive to search first for the Disk Operating System i e DOS The system will search those drives in order Ex C CDROM A System will first search for hard disk drive then CDROM drive and the last is floppy disk drive Note C is primary master D is primary slave E is secondary master F is secondary slave Swap Floppy Drive This item allows you to determine whether to enable the swap floppy drive or not The choice Enabled Disabled Boot Up Floppy Seek During POST the BIOS will determine if the floppy disk drive installed is 40 tracks 360K or 80 tracks 720K 1 2M 1 44M Enabled BIOS searches for floppy disk drive to determine if it is 40 or 80 tracks Disabled BIOS will not search for the type of floppy disk drive by track number 23 Chapter 3 Award BIOS Setup ATC6240V Mainboard Boot Up NumLock Status This allows you to determine the default state of the numeric keypad By default the system boots up with NumLock on On Keypad is for numeric keys
7. 3 1338 1297 32 65535 2594 63 LARGE Note Some OSes like SCO UNIX must use Normal for installation ESC Skip 37 Chapter 3 Award BIOS Setup ATC6240V Mainboard The last second item of the main menu is save and exit If you select this item and press Y then these records will be saved in the CMOS memory on the mainboard It will be checked every time you turn your computer on ROM PCI JISA BIOS CMOS SETUP UTILITY AWARD SOFTWARE INC STANDARD CMOS SETUP INTEGRATED PERIPHERALS BIOS FEATURES SETUP SUPERVISOR PASSWORD CHIPSET FEATURES SETUP USER PASSWORD POWER MANAGEMENT SETUP IDE HDD AUTO DETECTION PNP PCI CONFIGURATION SAVE amp EXIT SETUP LOAD BIOS DEFAULTS EXIT WITHOUT SAVING LOAD SETUP DEFAULTS ESC Quit AV gt Select Item F10 Save amp Exit Setup Shift F2 Change Color Time Date Hard Disk Type ROM PCI ISA BIOS CMOS SETUP UTILITY AWARD SOFTWARE INC STANDARD CMOS SETUP INTEGRATED PERIPHERALS BIOS FEATURES SETUP SUPERVISOR PASSWORD CHIPSET FEATURES SETUP USER PASSWORD POWER MANAGEMENT SETUP IDE HDD AUTO DETECTION PNP PCI CONFIGURATION SAVE amp EXIT SETUP LOAD BIOS DEFAULTS ESC Quit AV gt Select Item F10 Save amp Exit Setup Shift F2 Change Color Save Data to CMOS amp Exit SETUP 38 ATC6240V Mainboard Chapter 3 Award BIOS Setup LOAD BIOS DEFAULTS When your mainboard has problems and needs to trouble shoot the system you can use this function The default val
8. JP11 The mainboard provides Jumper 11 that allows you to set your CPU host clock and perform CPU overclock function There are two ways to set CPU host clock at closed and open When setting closed the system will automatically detect the CPU host clock for instance 66MHz and 100MHz Another way is to set Jumper 11 at open for 66MHz CPU overclock to 1OOMHz We recommend that users should use Intel Pentium I II 100 MHz CPU running at 350 400 450 and 500MHz internal clock speed Moreover the SDRAM memory module must be 8 nano second Maximum Frequency 125 MHz speed of memory die or less However based on Intel s design we don t recommend users to run over 100MHz CPU host bus Please note that the default setting of Jumper 11 is closed Jumper 11 BASE CLK Closed Base clock autodetected Open To be overclocked H Ji a Pin Closed b Pin Open JP11 Slot 1 KE In view of Intel s specific design overclocking to 100MHz or higher is not necessarily successful If you want to overclock your CPU base please set CPU Host PCI Clock in CHIPSET FEATURES SETUP in the BIOS setup screen After set to higher base if the system cannot boot up you should shut down your computer and restart it with the Insert key pressed down to clear up the set frequency It will then operate at the default frequency Chapter 1 Introduction ATC6240V Mainboard 1 3 4 SB Lin
9. Off Keypad is for arrow keys IDE HDD Block Mode This allows your HD controller to use the fast block mode to transfer data to and from your HD drive Enabled IDE controller uses block mode Disabled IDE controller uses standard mode Gate A20 Option This entry allows you to select how the gate A20 is handled The gate A20 is a device used to address memory above 1 MB Initially the gate A20 was handled via a pin on the keyboard Today while keyboards still provide this support it is more common and much faster for the system chipset to provide support for gate A20 Normal is keyboard Fast is chipset Memory Parity ECC Check Select parity ECC or Disabled depending on the type of DRAM installed in your system The choice ECC Parity Disabled Security Option This category allows you to limit access to the system and Setup or just to Setup System The system will not boot and access to Setup will be denied if the correct password is not entered at the prompt Setup The system will boot but access to Setup will be denied if the correct password is not entered at the prompt To disable the security select PASSWORD SETTING at Main Menu and then you will be asked to enter password Do not type anything and just press lt Enter gt it will disable the security Once the security is disabled the system will boot and you can enter Setup freely PCI VGA Palette Snoop It determines whether the MPEG ISA VESA VGA cards can
10. instead of entering a new password when the Enter Password dialog box appears A message will appear for confirming that the password is disabled CAUTION If you forget your password you must clear CMOS first and restart system in order to set up password again See Clear CMOS on Page 15 IDE HDD AUTO DETECTION This allows you to detect the IDE hard disk driver s parameters and enter them into Standard CMOS Setup automatically If the auto detected parameters displayed do not match the ones that should be used for your hard drive do not accept them Press lt N gt to reject the values and enter the correct ones manually on the Standard CMOS Setup screen SAVE amp EXIT SETUP This allows you to save the new setting values in the CMOS memory and continue with the booting process Select what you want to do press lt Enter gt EXIT WITHOUT SAVING This allows you to exit the BIOS setup utility without recording any new values or changing old ones 39 Chapter 3 Award BIOS Setup ATC6240V Mainboard 40 ATC6240V Mainboard Chapter 3 Award BIOS Setup X Control Key Description X I V Esc Help lt Shift gt F2 Old Value Load BIOS default Load setup default 41
11. manual would be the handiest assistant to help change the on board configuration or default setting In case this manual cannot solve all your problems please ask your dealer for help and be sure the warranty on your system is still valid REMARK Intel is a registered trademark of Intel Corporation All other brands and product names are registered trademarks of their respective companies ATC6240V Mainboard Chapter 1 Introduction CHAPTER 1 SYSTEM FEATURES 1 1 Introduction ATC6240V mainboard is designed to run with VIA Apollo 133 693A 596B chipset to enhance the performance and extraordinary value of the Intel Pentium I II and Celeron processor powered PC It is mounted with Slot 1 supporting 66MHz 100MHz and 133MHz Front Side Bus CPU To enhance its memory and peripheral support 4 DIMM sockets and 5 PCI slots are mounted on board In addition 1 AGP and 2 ISA slots can satisfy some exceptional users requirements 1 2 System Specifications CPU Slot supporting Intel Pentium II CPU 450Mhz to 733MHz Pentium II CPU 233MHz to 450MHz and Intel Celeron CPU 266MHz to 466MHz VIA VT82C693A VT82C596B AGP PClset Four 168 pin DIMM sockets in four banks of 64 bit wide path up to 1 5GB unbuffered SDRAM with parity chip ECC support Built in Switching Voltage Regulator VRM 8 2 SPEC One AGP slot two 16 bit ISA slots and five PCI slots compliance with reversion 2 2 of the PCI Local Bus specification Dual Master IDE
12. max retries are attempted without success Disable PCI 2 will be disconnected until access finished AGP Mater 1 WS Write Enable Disable AGP master one wait state write AGP Mater 1 WS Read Enable Disable AGP master one wait state read Assign IRO for VGA When this items is enabled the system will assign an IRQ for VGA If disabled VGA occupies no IRQ Assign IRQ for USB When this item is enabled the system will assign an IRQ for USB If disabled USB occupies no IRQ 33 Chapter 3 Award BIOS Setup ATC6240V Mainboard INTEGRATED PERIPHERALS This section page includes all the items of IDE hard drive and Programmed Input Output features See also Section Chipset Features Setup ROM PCI ISA BIOS INTEGRATED PERIPHERALS AWARD SOFTWARE INC OnChip IDE Channel 0 Enabled UART Mode Select Normal OnChip IDE Channel 1 Enabled UART Duplex Mode Half IDE Prefetch Mode Disabled RxD TxD Active Hi Lo Primary Master PIO Auto IR Transmission Delay Enabled Primary Slave PIO Auto Onboard Parallel Port 378 IRQ7 Secondary Master PIO Auto Parallel Port Mode ECP Secondary Slave PIO Auto ECP Mode Use DMA 3 Primary Master UDMA Auto EPP Mode Select EPP1 7 Primary Slave UDMA Auto PWRON After PWR Fail Off Secondary Master UDMA Auto Secondary Slave UDMA Auto Init Display first PCI Slot Power On Function Button Only Esc Quit AV gt 3 Select Item KBC Input Clock 8 MHz FI Help PU PD Mod
13. the VGA adapter to operate in a power saving mode Monitor will remain on during power saving modes Monitor is blanked when the system enters the Suspend mode Monitor is blanked when the system enters any power saving mode Video Off Method This determines the manner in which the monitor is blanked V H SYNC This selection will cause the system to turn off the vertical and Blank horizontal sync ports and write blanks to the video buffer Blank Screen _ This option only writes blanks to the video buffer DPMS Support Initial of Display Power Management Signaling Soft Off by PWR BTTN Instant off When push the power button the system power will be off immediately Delay 4 sec when push the power button it will enter suspend mode We need to push the power button and hold it for 4 seconds to turn off the power The Following 3 modes are Green PC power saving functions which are only user configurable when User Define power management has been selected gt Doze Mode When enabled and after the set time of system inactivity the CPU clock will run at slower speed while all other devices still operate at full speed gt Suspend Mode When enabled and after the set time of system inactivity all devices except the CPU will be shut off gt HDD Power Down When enabled and after the set time of system inactivity the hard disk drive will be powered down while all other devices remain active Modem Ring Res
14. 33MHz 133x4 0 for Mod 6240V 01 600MHz 133x4 5 for Mod 6240V 01 677MHz 133x5 0 for Mod 6240V 01 733MHz 133x5 5 for Mod 6240V 01 Chapter 2 Installation ATC6240V Mainboard 2 3 SYSTEM MEMORY INSTALLATION The ATC6240V provides four 168 pin DIMM sockets for system memory expansion from 8MB to 1 5GB Unbuffered SDRAM These four DIMMs are arranged to four banks please refer to page A Bank DIMM Memory Module Total Memory Bank0 DIMM1 8 16 32 64 128 256 512MB 8MB 512MB Bank1 DIMM2 8 16 32 64 128 256 512MB 8MB 512MB Bank2 DIMM3 8 16 32 64 128 256MB 8MB 256MB Bank3 DIMM4 8 16 32 64 128 256MB 8MB 256MB Total System Memory 8MB 1 5GB DRAM type size parity supported Z Unbuffered SDRAM with SPD Z Both parity or non parity are available Z 3 3V Single double side 8 16 32 64 128 256 512Mbytes For 66MHz host bus CPUs use 12ns or faster DIMM module For 100MHz host bus CPUs use 10ns or faster and PC 100 compliant modules Please insert 512MB memory module to DIMM 1 and DIMM2 x SPD Serial Presence Detect This EPROM contains speed and design information of the memory module The mainboard may get optimal performance via accessing the data of SPD x ECC Error Check and Correction This mainboard can support the ECC function while utilizing parity modules To enable this function users must set DRAM Data Integrity Mode to ECC through
15. ATC6240V Mainboard Contents CONTENTS QUICK JUMPER amp CONNECTOR SETTING csssseeee A CHECK LIST OF THE PACKAGING 0eeeeeeeeeeeDd CONNECTORS DESCRIPTION sss sss ss ss ss s ss s s s ses sese ees C TABLE OF E 8 N ER NEE ieii HOW TO USE THIS MANUAL ssseseessessoesooesoesooesosesoesooseoossoese 2 CHAPTER 1 System Feature sss sssssssssssssssssss esse essssssss sees J E Kr ee EEN gt 1 2 System 5 PECILICAUIONS isitin animal dallama asiller 3 1 3 Features Etsin OI e sl a stata a dE 4 1 3 1SoftwarePowerOffControl 4 ere Contro DE AN EE A NY d 4 1 3 33Running100MHzCPUBus P1 5 1 3 4SB linkSidebandsSignals 6 1 3 5 Modem Ring Eesen 6 1 3 6 Keyboard amp PS 2MousePowerOn JP9 7 1 3 7 Wake On A WEE 8 1 3 8 Ultra DMA 66 ablan ade tacit EE 8 CHAPTER 2 Installation ccccccssccccsccscccccccccccccccccscccesnn 9 2 1 Installation Procedure EE 9 DIAS PU Drees 9 2 2 1 Core Bus Freq Ratio Ee 9 2 2 2 EE 10 2 3 System Memory Installation sss sese 12 2 4 VIA IDE Driver SRerup sss sees eee eee eee eee 13 CHAPTER 3 Award BIOS Setup ccssssccsssssssssrsccsssssssees L5 3 1 Update BIOS Procedure egen 16 3 1 2 Update Microcode AP eleyen seoul 17 3 2 Award System BIOS Configuration Setup 18 Appendix A How to Install Pentium I I
16. Chipset Features Setup from the BIOS setup screen All in all ECC s function is to detect and correct the errors of transfer data ATC6240V Mainboard Chapter 2 Installation 2 4 VIA IDE DRIVER SETUP The VIA IDE drivers are enclosed into the VIA Utility CD Use this CD ROM for installation of the VIA drivers 2 4 1 Setup for Windows 9x 1 Starting Windows system 2 Insert the VIA Utility CD ROM into your CD ROM Drive If the VIA Driver Setup Main Menu does not appear automatically just point to My Computer and click the CD ROM icon to open the VIA Utility CD ROM directly 3 Ina second the VIA Service Pack v xx main menu shows up To start VIA drivers setup point to the VIA Integrated Setup and click on it 5 User friendly Setup screens will appear one by one guiding you to finish the complete setup 6 Among the guiding screens the Select Components screen as shown below will show you the programs to be installed into your system New users are recommended to install all of them VIA Service Pack 4 11 Select Components This setup program will install the following drivers If you don t want to install them you can uncheck the associated check box MW AGP VxD Driver IV VIA Chipset Functions Registry IV IRO Routing Miniport Driver lt Back Cancel 7 When the Setup complete screen appears click Finish to restart your computer so as to put the just installed drivers
17. I Celeron and Processors with SECC2 Package Appendix B Technical Support Request Form HOW TO USE THIS MANUAL How To Use This Manual ATC6240V Mainboard This manual is written in a user friendly style It would be advisable for users to read it in an orderly sequence 1 For Hardware Information Read Page A QUICK JUMPER amp CONNECTOR SETTING Page B CHECK LIST OF THE PACKAGING and Page C CONNECTORS DESCRIPTION 2 For Mainboard and System Features Read Chapter 1 System Features in detail and you will find helpful information on mainboard and system features Especially when you want to do some feature setup detailed instructions are provided therein to help you through 3 For CPU Memory and Drivers Installation Read Chapter 2 Installation for your CPU memory and application drivers installation Detailed instructions are provided to guide all kinds of users 4 For BIOS Update and Setup Read Chapter 3 Award BIOS Setup for updating your mainboard BIOS and setting up your BIOS Configuration 5 For Installing Pentium II III Celeron or Processors with SECC2 Package Read APPENDIX A for setting up Intel Pentium III Pentium I Celeron or processors with SECC2 package 6 For other Technical Support Read APPENDIX B fill and send the Request Form to your dealer for other technical support It is often heard that the default setting on a mainboard is not what user expects A user friendly
18. Mode first and load the API program to Drive C To load the program to C by following steps 1 Type md c api and press Enter Directory api is made in Drive C now 2 Insert the Driver Utility diskette or CD into Drive A or CD ROM Drive E 3 Then type copy a api c api or copy e api c api and press Enter API program is loaded to Drive C now 4 Type C api checkup to execute this program The main menu should now be displayed showing the following four options 1 Check and load updated 2 Specify stepping data file current pep pdb 3 Help 4 Quit without loading updated Select 1 to know the stepping filename select 2 to load right patch code then select 1 to update proper patch code Then cold boot mechanical power off system to continue For more information please refer to CHECKUP HLP file Chapter 3 Award BIOS Setup ATC6240V Mainboard 3 2 SYSTEM BIOS CONFIGURATION SETUP The following pages explain how to set up the BIOS configuration under the Award BIOS The SETUP program is stored in the Read Only Memory ROM on the mainboard To do the SETUP procedure press the lt Del gt key when the system is booting up The following main menu will appear Please select STANDARD CMOS SETUP to enter the next screen ROM PCI ISA BIOS CMOS SETUP UTILITY AWARD SOFTWARE INC STANDARD CMOS SETUP INTEGRATED PERIPHERALS BIOS FEATURES SETUP SUPERVISOR PASSWORD CHIPSET FEA
19. O 12 PS 2 Mouse Primary Off IRQ 13 Coprocessor Disabled LPT COM IRQ 14 Hard Disk Primary On IRQ 15 Reserved Disabled DMA Master Off Esc Quit bla Select Item Modem Ring Resume Disabled Help PU PD Modify RTC Alarm Resume Disabled Old Values Shift F2 Color Load BIOS Defaults Load Setup Defaults ACPI function This item is to set the ACPI Advanced Configuration Power Interface function enabled or disabled The default setting is disabled Power Management This category allows you to select the type or degree of power saving and is directly related to the following modes Doze Standby Suspend HDD Power Down Min Power Minimum power management Doze lhr Standby lhr Saving Suspend Ihr HDD Power Down 15min Max Power Dozezlmin Standby 1 min Suspend 1min HDD Power Saving Down 1min User Allows you to set each mode individually Each of the ranges is from Define Imin to Ihr except for HDD Power Down which ranges from to 15min Chapter 3 Award BIOS Setup ATC6240V Mainboard If you would like to use Software Power off Control function you should select Yes in PM Control by APM PM Control by APM When enabled an Advanced Power Management mechanism will be activated to enhance the Max Power Saving Mode and stop the CPU internal clock If the Max Power Saving is not enabled this will be shown as Yes Video off After When enabled this feature allows
20. TC6240V Mainboard Chapter 3 Award BIOS Setup 3 1 2 UPDATE MICROCODE API Intel also provides MICROCODE API Applications Programming Interface for Pentium II III processor based mainboard users to update data block in BIOS quickly and easily You can find this utility in the diskette or All In One CD in the package The BIOS code on the Pentium II III processor based mainboard contains data that is specific to each silicon stepping of the processor Integrators must ensure that this BIOS stepping data matches the processor stepping used When the BIOS does not contain stepping data that matches the processor stepping integrators must update the data in the BIOS before shipping the system Usually System is updated by replacing the entire BIOS with a new revision of BIOS that contains the correct stepping data Intel s BIOS updating API allows just the stepping data within the BIOS to be updated as needed Mainboards that contain a BIOS with the Intel defined BIOS updating API can be quickly and easily updated if required without obtaining a complete BIOS upgrade Using this utility integrators can easily verify that the correct stepping data is present in all mainboards However if the stepping data requires updating the mainboard BIOS must contain the Intel defined BIOS updating API otherwise a complete BIOS upgrade is required from the mainboard vendor Since API program can only be executed under DOS Real Mode you must enter Real
21. TURES SETUP USER PASSWORD POWER MANAGEMENT SETUP IDE HDD AUTO DETECTION PNP PCI CONFIGURATION SAVE amp EXIT SETUP LOAD BIOS DEFAULTS EXIT WITHOUT SAVING LOAD SETUP DEFAULTS ESC Quit AV gt Select Item F10 Save amp Exit Setup Shift F2 Change Color Time Date Hard Disk Type The section on the bottom of the main menu explains how to control this screen The other section displays the items highlighted in the list ATC6240V Mainboard Chapter 3 Award BIOS Setup STANDARD CMOS SETUP This screen records some basic hardware information and sets the system clock and error handling These records can be lost or corrupted if the on board battery has failed or is weak ROM PCI ISA BIOS STANDARD CMOS SETUP AWARD SOFTWARE INC Date mm dd yy Mon Sep 13 1999 Time hh mm ss 13 37 14 HARD DISKS TYPE SIZE CYLS HEAD PRECOMP LANDZ SECTOR MODE Primary Master Auto Primary Slave Auto Secondary Master Auto Secondary Slave Auto Drive A 1 44M 3 5 in Drive B None Base Memory Floppy 3 Mode Support Disabled Extended memory Other Memory Video EGA VGA Halt On All Errors AV gt Select Item PU PD Modify Shift F2 Change Color Date The date format is lt day gt lt date gt lt month gt lt year gt Press lt F3 gt to show the calendar day The day from Sun to Sat determined by the BIOS and is displayed only date The date from 1 to 31 The month Jan through Dec The year
22. ank 4 5 DRAM Timing SDRAM 10ns CPU Host PCI Clock Default Bank 6 7 DRAM Timing SDRAM 10ns SDRAM Cycle Length 73 DRAM Clock 66MHz Memory Hole Disabled Read Around Write Disabled Concurrent PCI Host Disable System BIOS Cacheable Disabled Video RAM Cacheable Disabled AGP Aperture Size MB 64M AGP 2x Mode Enabled OnChip USB Disabled USB Keyboard Support Disabled AV gt Select Item PU PD Modify F5 Old Values Shift F2 Color F6 Load BIOS Defaults F7 Load Setup Defaults Bank 0 1 2 3 4 5 DRAM Timing Each item is for selection of SDRAM speed Choices are 10ns 8ns Normal medium fast and Turbo In case a faster choice cannot bring about a smooth system run a slower choice should be taken Default is the slowest 10ns SDRAM Cycle Length There are 3 cycle lengths for choice 1 2 3 DRAM Clock This item is for selecting the desired DRAM Clock Host Clock means CPU Host Clock is chosen as the DRAM Clock HClock 33MHz means CPU Host Clock 33MHz is chosen as the DRAM clock Hclock 33MHz means CPU Host Clock 33MHz is chosen as the DRAM Clock 26 ATC6240V Mainboard Chapter 3 Award BIOS Setup Memory Hole A memory block at 15M 16M is reserved for choice If Disabled is chosen it means this memory block is not reserved for special use If I5M 16M is chosen it means this memory block is reserved for other devices Read Around write to enable this i
23. any attempt at modification If an attempt is made the BIOS will halt the system and the following error message will appear Afterwards if necessary you will be able to run an anti virus program to locate and remove the problem before any damage is done WARNING Disk boot sector is to be modified Type Y to accept write or N to abort write Award Software Inc 22 ATC6240V Mainboard Chapter 3 Award BIOS Setup Enabled Activates automatically when the system boots up If anything attempts to access the boot sector or hard disk partition table will cause a warning message to appear Disabled No warning message will appear when anything attempts to access the boot sector or hard disk partition table Many disk diagnostic programs which attempt to access the boot sector table can cause the above warning message If you will be running such a program we recommend that you first disable Virus Protection beforehand CPU LI Cache L2 Cache These two categories speed up memory access However it depends on CPU chipset design The default value is enabled CPU L2 Cache ECC Checking When this item is enabled it means the system supports Error Checking and Correcting ECC memory which can guard against data corruption Processor Number Feature The Processor Serial Number serves as an identifier for the Processor and its system and thus adds to the system security features When this feature is Enabled
24. connectors supporting Ultra DMA 66 66MB sec up to four devices in two channels for connecting of high capacity hard disk CD ROM LS 120MB floppy drive tape backup etc Winbond 83977 high speed Ultra Multi I O chipset ATX Power Connector USB Universal Serial Bus Connector supporting up to 127 peripheral devices PS 2 Keyboard Connector and PS 2 Mouse Connector Infrared Transfer IrDA TX RX Connector One FDD Port supporting two devices available for 1 2MB 1 44MB and 2 88MB Two 16550A fast UARTs compatible Serial Ports One EPP ECP mode Parallel Printer Port Software Power Off Control Modem Ring On SB Link Keyboard amp PS 2 Mouse Power On Wake On LAN functions ATX Form Factor Hardware Dimension is 305mm x 190mm 12 x 7 48 Chapter 1 Introduction 1 3 Features Highlight ATC6240V Mainboard 1 3 1 Software Power Off Control The mainboard design supports Software Power Off Control feature through the SMM code in the BIOS under Windows 95 98 and MS DOS operation system environment First you should connect the power switch cable to the connector PS ON on the mainboard In the BIOS screen of POWER MANAGEMENT SETUP
25. ed to the system 2 2 CPU INSTALLATION The mainboard has built in VID Voltage Identify function to automatically detect CPU voltages Thus you do not have to set the CPU voltage setting 2 2 1 CPU Core Bus Freq Ratio SW1 1 1 1 2 11 3 1 4 3 0x ON ON OFF OFF 3 5x ON ON JON OFF 4 0x OFF OFF OFF OFF 4 5x OFF OFF ON OFF 5 0x OFFJON OFF OFF 5 5x OFF ON JON OFF 6 0x ON OFF OFF ON 6 5x ON OFF ON JON 7 0x ON ON OFF ON 7 5x ON ON JON JON 8 0x OFF OFF OFF ON Chapter 2 Installation 2 2 2 CPU Setting ATC6240V Mainboard a For 233 333MHz Intel Pentium Il amp 266 466MHz Celeron CPUs INTERNAL CPU CLOCK SW1 ON 233MHz 66x3 5 E g g k OFF ON 266MHz 66x4 0 B bk k OFF 4 ON 300M 66x45 nmm OFF 4 ON 333MHz 66x5 0 E E k OFF 4 ON 366MHz 66x5 5 E E E OFF d ON 400MHz 66x6 0 E E E E OFF ON 433MHz 66x6 5 WI OFF ON 466MHz 66x7 0 E E E OFF ATC6240V Mainboard b For 350 450MHz Intel Pentium Il and 450 733MHz Pentium III CPUs INTERNAL CPU CLOCK Chapter 2 Installation 350MHz 100x3 5 O 2 OFF 400MHz 100x4 0 O 2 M Mm 2 Me MS AU 450MHZ 100x4 5 500MHZ 100x5 0 550MHz 100x5 5 600MHz 100x6 0 650MHz 100x6 5 700MHz 100x7 0 5
26. ers in an effort to keep as much base memory free for application programs The BIOS is the most frequent user of this RAM area since this is where it shadows RAM 21 Chapter 3 Award BIOS Setup ATC6240V Mainboard BIOS FEATURES SETUP This screen is a list of system configuration options Some of them are defaults required by the mainboard s design others depend on the features of your system ROM PCVISA BIOS BIOS FEATURES SETUP AWARD SOFTWARE INC Virus Warning Disabled Video BIOS Shadow Enabled CPU LI Cache Enabled C8000 CBFFF Shadow Disabled CPU 12 Cache Enabled CC000 CFFFF Shadow Disabled CPU L2 Cache ECC Checking Enabled D0000 D3FFF Shadow Disabled Processor Number Feature Enabled D4000 D7FFF Shadow Disabled Quick Power On Self Test Enabled D8000 DBFFF Shadow Disabled Boot Sequence A C SCSI DC000 DFFFF Shadow Disabled Disabled Enabled Boot Up NumLock Status On IDE HDD Block Mode Disabled Gate A20 Option Normal Memory Parity ECC Check Disabled Security Option Setup Esc Quit W gt Select Item IPCI VGA Palette Snoop Disabled F1 Help PU PD Modify OS Select for DRAM gt 64MB Non OS2 F5 Old Values SHIFT F2 Color HDD S M A R T capability Disabled F6 Load BIOS Defaults Report No FDD For WIN 95 No F7 Load Setup Defaults Virus Warning When this item is enabled the Award BIOS will monitor the boot sector and partition table of the hard disk drive for
27. eset Configuration Data Disabled PCI Master O WS Write Enabled PCI Delay Transaction Disabled PCI 2 Access 1 Retry Disabled AGP Master 1 WS Write Disabled AGP Master 1 WS Read Disabled Assign IRQ For USB Enabled Assign IRQ For VGA Disabled Esc Out h 5 e Select Item FI Help PU PD Modify F5 Old Values Shift F2 Color F6 Load BIOS Defaults F7 Load Setup Defaults PNP OS Installed This item allows you to determine PnP OS or not Choices are Yes or No Resources Controlled by The Award Plug and Play BIOS has the capability to automatically configure all of the boot and Plug amp Play compliant devices However this capability means absolutely nothing unless you are using a Plug and Play OS such as Windows 95 Choices are Auto and Manual Reset Configuration Data This item allows you to determine whether to reset the configuration data or not CPU to PCI Write Buffer Enable Disable CPU to PCI POST Write PCI Dynamic Bursting Enable Disable PCI burst operation PCI Master 0 WS Write Enable PCI Master 0 wait state mode Disable PCI Mater 1 wait state mode 32 ATC6240V Mainboard Chapter 3 Award BIOS Setup PCI Delay Transaction This chipset has an embedded 32 bit posted write buffer to support deadly transactions cycles Select Enabled to support compliance with PCI specification version 2 1 The choice Enabled disabled space PCI 2 Access 1 Retry Enable PCI 2 will be disconnected if
28. from 1900 to 2099 Time The time format is lt hour gt lt minute gt lt second gt The time is calculated based on the 24 hour military time clock For example Ip m is 13 00 00 Primary Master Primary Slave Secondary Master Secondary Slave These categories identify the types of the 2 channels that have been installed in the computer There are 45 predefined types and 4 user definable types for Enhanced IDE BIOS Type 1 to 45 which are predefined Type user which is user definable Press PgUp PgDn to select a numbered hard disk type or type the number and press lt Enter gt 19 Chapter 3 Award BIOS Setup ATC6240V Mainboard If you select Auto the BIOS will detect the HDD amp CD ROM Drive automatically at the POST stage and show the IDE for HDD amp CD ROM Drive If you select user you will need to know the information listed below This information should be from your hard disk vender or dealer Then enter the figure directly and press lt Enter gt If the controller of the HDD interface is ESDI the selection shall be Type 1 if SCSI the selection shall be None If no device is installed select NONE and press lt Enter gt Drive A Drive B This category identifies the types of floppy disk drive A or drive B that has been installed in the computer 3 5 double side 720KB capacity Floppy 3 Mode Support This is the Japanese standard floppy drive This standard stores 1 2MB in a 3 5 diskette
29. ify Onboard FDC Controller Enabled F5 Old Values Shift F2 Color Onboard Serial Port 1 3F8 IRQ4 F6 Load BIOS Defaults Onboard Serial Port 2 3F8 IRQ3 F7 Load Setup Defaults OnChip IDE Channel 0 OnChip IDE Channel 1 This setup item allows you to either enable or disable the primary secondary controller You might choose to disable the controller if you want to add higher performance or specialized controller IDE Prefetch Mode Enable Disable IDE Read Prefetch Buffer Primary Master Slave PIO Secondary Master Slave PIO PIO Programmed Input Output it allows the BIOS to tell the controller what it wants and then let the controller and the CPU to complete the task by themselves This is simpler and faster Your system supports five modes 0 4 which primarily differ in timing When Auto is selected the BIOS will select the best available mode Primary Master Slave UDMA Secondary Master Slave UDMA Auto will support the Ultra DMA function Disabled will not support the Ultra DMA function 34 ATC6240V Mainboard Chapter 3 Award BIOS Setup Init Display First If you set this item to PCI Slot it will activate the PCI video card firs in the multi displayed environment The choice PCI Slot AGP Power On Function The following are choices of Power On functions gt KB Power On Password This function is available with ATX power only User can power on the system by setting a password via keyboard Please refer to Page 5
30. ing the correct PS 2 Mouse button Do not slide the mouse when you click or you can t power on the system Button Only via Power Button Button Only is default setting at which computer can only be on off via Power Button 7 Chapter 1 Introduction ATC6240V Mainboard 1 3 7 Wake On LAN The remote Wake On LAN WOL mode of operation is a mechanism that uses Advanced Micro Device Magic Packet technology to power on a sleeping workstation on the network This mechanism is accomplished when the LAN card receives a specific packet of information called a Magic Packet addressed to the node on the network For additional protection Secure ON is an optional security feature that can be added to the Magic Packet that requires a password to power on the sleeping workstation When LAN card is in remote Wake On LAN mode main system power can be shut down leaving power only for the LAN card and auxiliary power recondition The LAN card performs no network activities while in the remote Wake On LAN mode of operation It only monitors the network for receipt of a Magic Packet If a Magic Packet is addressed to the LAN card on the network the LAN card wake up the system If the Secure ON feature has been enabled the password added to the Magic Packet is also verified prior to waking up the system You should select two kinds of PCI Ethernet cards with WOL function One is Intel and the other is with PME signal supporting And you can se
31. into effect 13 Chapter 2 Installation ATC6240V Mainboard 2 4 2 Setupfor Windows NT 4 0 The VIA IDE drivers for WinNT are also enclosed into the VIA Utility CD Use this CD ROM for installation of the VIA drivers for WinNT 1 Starting Windows NT 4 0 2 Insert the VIA Utility CD ROM into your CD ROM Drive point to My Computer and click the CD ROM icon to open the VIA Utility CD ROM directly 3 In a second the VIA Service Pack v xx main menu shows up as below 4 Point to VIA Integrated Setup and click on it to start setup right away 5 Successive screens with user friendly instructions will appear to guide you through the whole setup 6 When the Setup complete screen appears click Finish to restart your computer so as to put the just installed drivers into effect ATC6240V Mainboard Chapter 3 Award BIOS Setup CHAPTER 3 AWARD BIOS SETUP Award BIOS manufacturer provides access to the system BIOS through the hardware and software on the mainboard The hardware consists of a Flash ROM and the software is a group of programs that are installed in the ROMBIOS along with all the other data the BIOS must contain After the BIOS is updated if you want to clear the old setup data stored in the CMOS then you can clear CMOS NOTE In case CMOS should be cleared unplug the power cord set Jumper 8 2 3 closed for at least 5 seconds put it back to 1 2 position and plug the power cord again PS
32. k Sideband Signals In order to migrate the legacy Sound Blaster compatible audio to the PCI bus EMU8008 incorporates a pair of SB Link request grant sideband signals PCPCIR EQN and PCPCIGNTN to interface to the PCI bus SB Link is a mechanism that was defined and developed by Intel as a docking solution which allows ISA slots to exist in docking stations connected to desktop PC PCI bus ISA Slots PCI Slot SB Link 2x3 sideband header sound will also as a 2x3 header and a cable REQ GND P SIRQ GNT A GND 1 3 5 Modem Ring On With Modem Ring On function the computer can wake up remotely through the connected modem This function enables users to access their computer data from anywhere in the world But users have to set Resume by Ring with enabled in Power Management Setup from the BIOS setup screen ATC6240V Mainboard Chapter 1 Introduction 1 3 6 Keyboard amp PS 2 Mouse Power On with JP9 With ATX Power Supply and Jumper 9 set to Pin 1 2 closed ATC6240V Mainboard is enabled to Keyboard amp PS 2 Mouse Power On functions JP 9 KB amp PS 2 Mouse Wakeup Enable A E i K rid e 1 td i ra t LC ETT Disable PCI slot SD bd Ma a PEDONE 1 2 2 3 JP9 i a Enable 1 2 closed b Disable 2 3 closed ISA slots The default Power On function is Button Only That means we can only turn our computer on and off b
33. rum Modulated Enable Disable this item the BIOS will Enable Disable the clock generator spread spectrum CPU Host PCI Clock Use this item to set CPU base clock frequency which includes 68 34MHz 75 37MHz 83 41MHz 66 33MHz 103 34MHz 112 37MHz 133 33MHz 100 33MHz 117 39MHz 117 29MHz 124 31MHz 129 32MHz 138 34MHz and Default 27 Chapter 3 Award BIOS Setup ATC6240V Mainboard Note After you change the CPU Clock Frequency and the system can not start please do the following procedures 1 Turn the system off firstly 2 Turn on the system Then press and hold the Insert key at boot 3 Select the proper frequency in the item of CPU Host PCI Clock 4 Save and Exit Setup 28 ATC6240V Mainboard Chapter 3 Award BIOS Setup POWER MANAGEMENT SETUP This screen controls the green features of this mainboard ROM PCVISA BIOS POWER MANAGEMENT SETUP AWARD SOFTWARE INC ACPI function Enabled Primary INTR On Power Management User Define IRQ 3 COM 2 Primary PM Control by APM Yes IRQ 4 COM 1 Primary Video Off After Suspend IRQ 5 LPT2 Primary Video Off Method V H SYNC Blank IRQ 6 Floppy Disk Primary Modem Use IRQ lt 5 IRQ 7 LPT 1 Primary Soft Off by PWR BTTN Delay 4 Sec IRQ 8 RTC Alarm Disabled HDD Power Down Disabled IRQ 9 IRO2 Redir Secondary Doze Mode Disabled IRQ 10 Reserved Secondary Suspend Mode Disabled IRQ 11 Reserved Secondary PM Events IR
34. t Wake Up On LAN this function enabled through Power Management Setup from the BIOS setup screen 1 3 8 Ultra DMA 66 Cable Ultra DMA 66 cable 40 pin connector amp 80 line cable is packaged which supports both UDMA 33 amp UDMA 66 on the mainboard And the Ultra DMA 66 color coded connectors for connection are shown as bellow QOOO00000000000000900 OOON000000s000000000 Blue to Mainboard Grey to Slave Black to IDE Peripheral Master q INE DArnhnaral Chapter 2 Installation ATC6240V Mainboard CHAPTER 2 INSTALLATION 2 1 INSTALLATION PROCEDURE Before installing the computer please prepare all components such as CPU DRAM peripherals such as hard disk keyboard CD ROM and accessories such as cables Then install the system as following Plug CPU heat sink refer to Pentium II II amp Celeron installation guide Appendix A and DRAM modules on the mainboard Set DIP switch amp jumpers based on your configuration Plug add on cards into PCI ISA slots if needed Connect cables to peripheral devices especially for power supply Make sure all components and devices are well connected turn on the power and setup System BIOS based on your configuration Install peripheral devices add on card drivers and test them If all of above procedures are running successfully turn the power off and screw the chassis cover to the chassis and then connect external devices which are cabl
35. tem will optimize DRAM read amp write If a memory read is addressed to a location where a memory write is held in a buffer content the memory read will not be sent to DRAM then Concurrent PCI Host Disabled the CPU bus will be occupied BPRI asserted during the entire PCI operation Enabled the CPU bus is only requested before ADS assertion System BIOS Cacheable Selecting Enabled allows the caching of the system BIOS ROM at FOOOOh FFFFFh resulting in better system performance However if any program writes to this memory area a system error may result Video RAM Cacheable Selecting Enabled allows the caching of the video RAM resulting in better system performance However if any program writes to this memory area a system error may result AGP Aperture Size MB Select the size of the AGP aperture The aperture is a portion of the PCI memory address range dedicated for graphics memory address space Host cycle that hit the aperture range are forwarded to the AGP without any translation See e lee AGP information The choice 4 8 16 32 64 128 256 OnChip USB If Enabled USB Keyboard Support will be provided for choice USB Keyboard Support If OnChip USB is enabled this item will appear for choice Auto Detect DIMM PCI CIK If this item is enabled the unused DIMM and PCI slot clock will be disabled If this item is disabled the unused DIMM and PCI slot will still get the active clock signal Spread Spect
36. ues loaded only affect the BIOS Features Setup Chipset Features Setup Power Management Setup and PNP PCI Configuration Setup There is no effect on the Standard CMOS Setup To use this function select it from main menu and press lt Enter gt A line will appear on the screen asking if you want to load the BIOS default values Press lt Yes gt and lt Enter gt then the BIOS default values will be loaded LOAD SETUP DEFAULTS This allows you to load optimal settings which are stored in the BIOS ROM The default values loaded only affect the BIOS Features Setup Chipset Features Setup Power Management Setup and PNP PCI Configuration Setup There is no effect on the Standard CMOS Setup To use this function select it from main menu and press lt Enter gt A line will appear on the screen asking if you want to load the Setup default values Press lt Yes gt and lt Enter gt then the Setup default values will be loaded SUPERVISOR PASSWORD USER PASSWORD This allows you to set the password The mainboard defaults with password disabled If you set both supervisor and user passwords only the supervisor password allows you to enter the BIOS SETUP program Enter Change password Enter the current password And at the prompt key in your new password up to eight alphanumeric characters then press lt Enter gt At the next prompt confirm the new password by typing it again and press lt Enter gt Disable password Press the lt Enter gt key
37. ume Enabled when system is in suspend mode it can be waked up by modem Disabled it cannot be waked up by modem 30 ATC6240V Mainboard Chapter 3 Award BIOS Setup PM Events Events included herein are I O events whose occurance can prevents the system from entering a power saving mode or can awaken the system from such a mode In fact the system remains alert for anything which occurs on a device which is configured as ON even when the system is in a password down mode When an I O device wants to gain the attention of the operating system it signal this need by causing an IRQ Interrupt Request to occur When the operating system is ready to respond to the request it interrupts itself and performs the service When set to Off device activity will neither prevent the system from going into a power management mode nor awaken the system The I O events included herein are VGA LPT amp COM HDD amp FDD DMA Master Modem Ring Resume RTC Alarm Resume Primary INTR This item is to provide setting for IRQ3 to IRQ15 If this item is ON you can set the IRQs with three choices Primary Secondary and Disabled 31 Chapter 3 Award BIOS Setup ATC6240V Mainboard PNP PCILCONFIGURATION This screen configures the PCI Bus slots ROM PCI AISA BIOS PNP PCI CONFIGURATION AWARD SOFTWARE INC PNP OS Installed No CPU to PCI Write Buffer Enabled Resources Controlled by Auto PCI Dynamic Bursting Disabled R
38. work with PCI VGA or not Enabled When PCI VGA working with MPEG ISA VESA VGA Card Disabled When PCI VGA not working with MPEG ISA VESA VGA Card OS Select for DRAM gt 64MB This item allows you to access the memory that is over 64MB in OS 2 The choice Non OS2 OS2 24 ATC6240V Mainboard Chapter 3 Award BIOS Setup HDD S M A R T Capability Select Enabled if your Hard disk supports S M A R T Safe Monitoring Analysis and Reporting Technology function Report No FDD For WIN 95 Set this item to Yes BIOS will report FDD to Win95 If in standard CMOS setup set Drive A to none and set this item to yes Inside Win95 My Computer and File manager Disk A will show Removable Disk A Video BIOS Shadow Determines whether video BIOS will be copied to RAM However it is optional depending on chipset design Video Shadow will increase the video speed The choice Enabled Disabled C8000 CBF FF Shadow DC000 DF FFF Shadow These categories determine whether option ROMs will be copied to RAM An example of such option ROM would be the support of onboard SCSI The choice Enabled Disabled 25 Chapter 3 Award BIOS Setup ATC6240V Mainboard CHIPSET FEATURES SETUP This screen controls the setting for the chipset on the mainboard ROM PCI ISA BIOS CHIPSET FEATURES SETUP AWARD SOFTWARE INC Bank 0 1 DRAM Timing SDRAM 10ns Auto Detect DIMM PCI CIK Enabled Bank 2 3 DRAM Timing SDRAM 10ns Spread Spectrum Modulated Disabled B
39. y pressing the Power Button If we want to enable KB amp PS 2 Mouse Power On function we first have to set JP9 to Pin 1 2 closed and then go to Power On Function in Integrated Peripherals of Award BIOS Setup At the line Power On Function we can press Page Up or Page Down to make the following selections 1 Password via Keyboard When user selects Password it will show Enter Password After user has typed the password screen will show Confirm Password and user has to type the same password to confirm it Save selection and shut down system Now computer will only be powered on by entering correct password In case the set password is forgotten carry out Clear CMOS Page 15 to clear password or computer can not be powered on Hot Key via Keyboard When user selects this option screen will show another line Hot Key Power ON Ctrl F1 User can select from Ctrl F1 to Ctrl F12 as Hot Key by pressing PageUp PageDown After fixing Hot Key save selection and shut down system Now computer will only be powered on by pressing the correct Hot Key Mouse Left Mouse Right via PS 2 Mouse This function is available via PS 2 mouse only User can select either Mouse Left or Mouse Right from the Power On Function line After picking either option save selection and shut down system Now computer will only be powered on by double click
Download Pdf Manuals
Related Search