Hotpoint 24 in. HDA3400G Built
Contents
1. e Troubleshooting Tips Consumer Support Before you call for service Problem Possible Causes Dishes and flatware Inlet water temperature not clean is below 120 F What To Do e Raise the water heater temperature to 120 F Use the HOT PREWASH feature Water pressure is temporarily low Turn on a faucet Is water coming out more slowly than usual If so wait until pressure is normal before using your dishwasher Air gap is clogged Clean the air gap Improper rack loading Spots and filming Extremely hard water on glasses and flatware Low inlet water temperature Overloading the dishwasher Improper loading Old or damp powder detergent Rinse agent dispenser empty Too little detergent Cloudiness on Combination of soft glassware water and too much detergent Make sure large dishware does not block the detergent dispenser or the wash arm Use Jet Dry rinse agent to remove spots and prevent new film buildup To remove stubborn spots and pre existing film from glassware 1 Remove all metal utensils from the dishwasher 2 Do not add detergent 3 Select the longest cycle 4 Start the dishwasher and allow to run for 18 to 22 minutes Dishwasher will now be in the main wash 5 Open the door and pour 2 cups 500 ml of white vinegar into the bottom of the dishwasher 6 Close the door and allow to complete the cycle If vinegar rinse doesn t work Repeat as above except use 1 42. Hotpoint com Turn on the hot water faucet nearest the dishwasher place the thermometer in a glass and let the water run continuously into the glass until the temperature stops rising Jet Dry rinse agent removes spots and prevents new film buildup on your dishes glasses flatware cookware and plastic Filling the Dispenser Fill the rinse agent dispenser until it reaches the bottom of lip inside the opening Replace cap To check if rinse agent is needed remove the cap and look into the dispenser A full dispenser should last about one month If rinse agent spills wipe up the excess Proper Use of Detergent Use only detergent specifically made for use in dishwashers Cascade Cascade Complete and Electrasol Automatic Dishwashing Detergents have been approved for use in all GE dishwashers Keep your detergent fresh and dry Don t put powder detergent into the dispenser until you re ready to wash dishes The amount of detergent to use depends on whether your water is hard or soft With hard water you need extra detergent With soft water you need less detergent Protect your dishes and dishwasher by contacting your water department and asking how hard your water is Twelve or more grains is extremely hard water A water softener is recommended Without it lime can build up in the water valve which could stick while open and cause flooding Too much detergent with soft water can cause a permanent c
3. C Check for leaks around the door A leak around the door could be caused by dishwasher door rubbing or hitting against adjacent cabinetry Reposition the dishwasher if necessary The dishwasher will drain about 5 minutes after the first fill Check drain lines If leaks are found turn off power correct as necessary and restore power Open dishwasher door and make sure most of the water has drained If not check that disposer plug has been removed and or air gap is not plugged L Let the dishwasher run through another fill and drain cycle Check again to be sure there are no leaks L At the end of the second drain push the reset pad on electronic models On dial models unlatch the door and rotate the dial to the OFF position INSTALLATION INSTRUCTIONS continued Step 18 Replace access panel and toekick Refer to Figure V Place the toekick against the legs of the dishwasher Align the access panel to the dishwasher and tighten the two access panel screws Align the toekick and make sure the bottom edge is against the floor Insert and tighten the two toekick attachment screws making sure the bottom edge of the toekick stays in contact with the floor Tighten 2 Access Panel Screws Attachment Screws Figure V Step 19 Literature L Be sure to leave complete literature package and installa tion instructions with consumer Pub Nga31i30515 SPECIFICATIONS SUBJECT TO CHA
4. Water Valve Bracket Figure Q Step 14 connect drain line Follow all local codes and ordinances DRAIN LINE PREPARATION The molded end is designed to fit 5 8 3 4 or 1 diameter connections to the air gap waste tee or disposer Cut on premarked line as required for your installation as illustrated in Figure R Note DO NOT CUT CORRUGATED PORTION OF HOSE Cutting Lines Waste tee installation Disposer Installation Figure S Method 2 High drain loop with waste tee or disposer Figure R Do not cut corrugated portion of hose Fasten to underside Fasten to underside of countertop of countertop If the location requires a longer drain hose add up to 42 of length to the factory installed hose Use 5 8 or 7 8 inside diameter hose and a short section of copper water pipe of appropriate length and diameter to connect the two hose ends Secure connection with appropriate clamps not supplied Note TOTAL DRAIN HOSE LENGTH MUST NOT EXCEED 10 FEET FOR PROPER DRAIN OPERATION Waste tee installation _ Disposer Installation DRAIN LINE INSTALLATION Figure T Connect drain line to air gap waste tee or disposer using Note BE SURE TO REMOVE DRAIN PLUG FROM DISPOSER either Method 1 or Method 2 as previously determined Refer BEFORE ATTACHING DRAIN LINE DISHWASHER WILL NOT to Figure sor Pidure T DRAIN IF PLUG IS LEFT IN PLACE Secure connection using appropriate clamps not supplied Make sure dr
5. components under dishwasher Water Power Line Supply Figure L Step 8 Insert drain hose through cabinet Upright dishwasher and position in front of the cabinet opening Insert the drain hose into the hole previously drilled in the cabinet wall If a power cord is used guide the end through a separate hole cut for the electrical cord Power cord should be routed directly to the rear of junction box avoiding contact with spring or other dishwasher components Step 8A install Trim Pieces on some models Press the trim onto the tub flange on each side of the dishwasher Start even with the top edge and press in as you move to the bottom Press trim piece onto top dishwasher flange Open and close the door to check that trim does not bind Note Tub trim is located in dishwasher upper rack Step 9 slide dishwasher into cabinet Slide the dishwasher into the opening a few inches at a time As you proceed pull the drain hose through the opening and under the sink Make sure drain hose is not kinked under dishwasher Check to be sure there is no interference with water line and wiring DO NOT PUSH AGAINST FRONT DOOR PANEL WITH YOUR KNEE Damage to the door panel will occur Figure N Step 10 Align water and electrical lines Route the water line and electrical supply to their connection locations under the dishwasher Do n
6. the dishwasher drains into a disposer run disposer clear Use only automatic dishwasher detergents to avoid sudsing Cascade Cascade Complete and Electrasol Automatic Dishwashing Detergents have been approved for use in all GE dishwashers To remove suds from the tub open the dishwasher and let suds evaporate Add 1 gallon of cold water to the tub Close and latch the dishwasher Pump out water by slowly turning the Dial until a drain period is reached Repeat if necessary Rinse agent was spilled Detergent with Always wipe up rinse agent spills immediately e Some detergents contain colorant pigment or dyes that will discolor Dishes don t dry colorant was used the tub interior with extended use Check the detergent cup for signs of any discoloration If cup is discolored change to detergent without any colorant Cascade Cascade Complete and Electrasol Automatic Dishwashing Detergents have been approved for use in all GE dishwashers Some tomato based foods can stain Low inlet water Use of the RINSE ONLY cycle on some models after adding the dish to the load can decrease the level of staining Make sure inlet water temperature is correct temperature Rinse agent dispenser is empty Check the rinse agent dispenser 11 suon nysuj Ajajeg m S Q A S S D TOTO TEST PTT pioddns saunsuoy Safety Instructions A S T S S t i
7. Built In Installation instructions for your new Dishwasher A CA U TI ON Before you begin Read these instructions completely and carefully e IMPORTANT Save these instructions for local inspector s use e IMPORTANT O0BSERVE ALL GOVERNING CODES AND ORDINANCES o Note to Installer Be sure to leave these instructions with the Consumer e Note to Consumer Keep these instructions with your Owners Manual for future reference If you have a question concerning the installation of this Installation of this dishwasher requires basic mechanical and product call the GE Answer Center Consumer Information electrical skills Proper installation is the responsibility of the Service at 800 626 2000 24 hours a day 7 days a week installer Product failure due to improper installation is not ELA If you received a damaged dishwasher covered under the GE Appliance Warranty See the back uade you should immediately contact your cover of the Owners Manual for warranty information Eee gn dealer or builder The dishwasher MUST be installed to allow for future removal from the enclosure if service is required PARTS SUPPLIED FOR INSTALLATION C Two Phillips head countertop mounting screws taped to dishwasher MATERIALS YOU WILL NEED Materials required L 90 elbow 3 8 NPT external thread on one end and opposite end sized to fit water supply T eor Electrical Cabl C Thread seal tape e Con
8. Dishwasher Dimensions in inches Installation Information Wood Insert Cut Out in inches Dimensions in inches 25 3 4 A Countertop 23 3 8 F M must Beresa gt Ec Door insert A Panel Thickness Sa Sa 90 T pipes or wires 90 PIN 4 4 Electrical Detail D d wiring is gt A 4 3 from y Hot Ee Le 5 gt Y 5 N cabinet water K Electrical C 34 MIN lineon S412404 c 6 wiring on A ae id ii N To oor Plumbing ET electrical i B 2 NS serve must enter I 21 1 2 5 19 MIN from wall 24 From wall a e NL Panel 3 1 4 s 24 MIN X Models Kits A B C Thickness x 4 Adjustable GPF325 Kit 18 7 8 23 9 18 3 11 16 1 4 M 3 3 4 to GPF375 Kit 18 15 16 23 5 8 4 1 4 3 4 Bottom of panel must be notched 1 1 2 x 1 2 to clear Electrical Rating Note Dishwasher must not be installed more than 10 from sink access panel See illustration above Malada AG fua Duc DOE QU e uM dat 120 for proper drainage All plumbing and electrical work must be in Adjustment required to mateh adjcent cabinets TON US to Herbae oes anen slau nesa tee ses acad 60 accordance with local codes Dishwasher includes drain hose levein aa asimani Seppa Total connected load amperage 8 6 and leveling legs Calrod heater watts D 500 Installation Information Before installing consult installation For use on adequately wired 120 volt 15 amp instructions packed with product for current
9. EATED ON OFFe Safety Instructions DRYING Model HDA1200 HOT PREWASH BETON e NORMAL WASH HEATED OFF o ON DRYING RINSE ONLY 6 S S D IS 3 m Model HDA2000 HOT PREWASH e HEAVY WASH OPTION e NORMAL WASH D OFFe e WATER SAVER ON DRYING e RINSE ONLY eaten pry or Model HDA3400 HOT PREWASH OPTION e START e POTS NORMAL HI TEMP WASH HEATED DRY FF OFF o e WATER SAVER amp PANS WASH ON iO OOO cycle energy saver selector options Troubleshooting Tips PLATE WARMER e RINSE ONLY eaten ory oFF HEATED DRY ON Model HDA3700 HOT PREWASH OPTION 1 POTS amp PANS DELAY 26 9 START HOURS e cycle energy saver e HEAVY NORMAL selector options TART WATER OFF SAVER e POTS HEAVY NORMAL HOT HI TEMP HEATED RESET MER amp PANS WASH WASH PREWASH WASH DRY OPTIONS HEATED DRY ON Consumer Support RINSE ONLY HEATED DRY OFF Hotpoint com Control Settings Cycles POTS amp PANS For heavily soiled dishes or cookware with dried on or baked on soils Everyday dishes may be included HEAVY WASH This cycle will not remove burned on foods NORMAL WASH For loads of everyday dishes glasses and cookware with medium soils NOTE Many dishes have lighter soil than normal Choosing a cycle other than NORMAL WASH will save energy and water suononysuy Ajajeg SHORT WASH For quickly washing loads of everyday d
10. NGE WITHOUT NOTICE ie ine orum Dishwashers Hotpoint com Safety Instructions 253 DEO Operating Instructions HDA1000 Care and Cleaning 9 HDA1200 Control Panels 0 4 HDA 2000 Control Settings 5 HDA3400 Dial Gycles 5 ve n 6 HDA3700 Loading the Dishwasher Racks 8 Optional Accessories 10 Using the Dishwasher 7 8 Troubleshooting Tips 11 12 Consumer Support Consumer Support Back Cover Product Registration 13 14 Warranty 6 6 eee eee 15 Write the model and serial numbers here Model Serial You can find them on a label on the tub wall just inside the door 165D4700P264 39 5938 1 06 02 JR Safety Instructions PA S S E t iS e Troubleshooting Tips Consumer Support IMPORTANT SAFETY INFORMATION READ ALL INSTRUCTIONS BEFORE USING vl S T WATER HEATER SAFETY NU A WARNING For your safety the information in this manual must be followed to minimize the risk of fire or explosion electric shock or to prevent property damage personal injury or death N Under certain conditions hydrogen gas may be produced in a water heater that has not been used for QN two weeks or more HYDROGEN GAS IS EXPLOSIVE If the hot water has not been used for two weeks or more prevent the possibility of damage or injury by turning on all hot water faucets and allow them to run for se
11. ain hose is not kinked INSTALLATION INSTRUCTIONS continued Step 15 connect power supply Verify that power is turned off at source If power cord is used plug it into the wall outlet and go to Step 16 If dish washer is to be directly wired to house wiring continue with this step Remove junction box cover Secure the power supply cable to the back of the junction box with a strain relief not supplied Sil WARNING Gy If house wiring is not 2 wire with a ground wire a ground must be provided by the installer When house wiring is aluminum be sure to use U L Listed anti oxidant compound and aluminum to copper connectors Locate the three dishwasher wires white black and green with the stripped ends Insert the three wires through the small hole in the junction box bracket Using wire nuts of appropriate size connect incoming ground to green wire white to white and black to black as shown in Figure U Replace the junction box cover Check to make sure that wires are not pinched under junction box cover White Neutral Ground i d J s N Note Check That Harness Leads Are Threaded Thru Small Hole in Bracket Figure U Step 16 Pre test check list Check to be sure power is off Open dishwasher door and remove all foam and card board packaging Remove literature package with Use amp Care manual Read the Use amp Care manual to familiarize yourself with the ope
12. al offers and other important communications from GE Appliances GEA Check here if you do not want to receive communications from GEA s carefully selected partners General Electric Company Louisville Kentucky GEAppliances com 14 M ee ee ee eB M eB ee ee ee ee ewe ee ee ee ee ee ee ee Hotpoint Dishwasher Warranty All warranty service provided by our Factory Service Centers or an authorized Customer Care technician To schedule service on line 24 hours a day visit us at GEAppliances com or call 800 GE CARES 800 432 2737 Staple your receipt here Proof of the original purchase date is needed to obtain service under the warranty For The Period Of GE Will Replace One Year Any part of the dishwasher which fails due to a defect in materials or workmanship During From the date of the this full one year warranty GE will also provide free of charge all labor and in home service original purchase to replace the defective part Second Year Only Any part of the Water Distribution System which fails due to a defect in materials or for models HDA2000 workmanship Associated inlet and drain plumbing parts are not covered by this warranty HDA3400 and HDA3700 During this second year limited warranty you will be responsible fo
13. cup 60 ml of citric acid crystals instead of vinegar This is called etching and is permanent To prevent this from happening use less detergent if you have soft water Wash glassware in the shortest cycle that will get them clean Water temperature entering the dishwasher exceeds 150 F Yellow or brown film Tea or coffee stains on tub Lower the water heater temperature Remove the stain by hand using a solution of 1 2 cup bleach and 3 cups warm water WARNING Before cleaning interior wait at least 20 minutes after a cycle for the heating element to cool down Failure to do so can result in burns An overall yellow or brown film can be caused by iron deposits in water White film on inside Hard water minerals surfaces Detergent cup lid Dial is not in the OFF won t latch position Detergent left in Dishes are blocking the dispenser cups detergent cups Steam This is normal Black or gray Aluminum utensils have marks on dishes rubbed against dishes 12 A special filter in the water supply line is the only way to correct this problem Contact a water softener company To clean the interior apply dishwasher detergent to a damp sponge Wear rubber gloves Do not use any type of cleanser other than dishwasher detergent because it may cause foaming or sudsing Cascade Cascade Complete and Electrasol Dishwashing Detergents have been approved for use in all GE dishwashers Turn the Dial to OFF a
14. d 2 Be sure the door is unlatched 3 Slowly turn the Dial to RINSE ONLY 4 Latch the door to start the cycle Delayed Start The HOURS DELAY will allow you to delay the start time of any cycle not on the Dial automatically for up to 6 hours 7 Be sure the door is unlatched 2 Select the wash cycle and option you want g Slowly turn the Dial to desired time The DELAYED START light will come on 4 Latch the door to start the cycle Plate Warmer For warming clean dishes and serving plates This cycle will take approximately 32 minutes 7 Load clean dishware to be warmed 2 Select HEATED DRY HEATED DRY ON 3 Be sure the door is unlatched 4 Slowly turn the Dial to PLATE WARMER 5 Latch the door to start the cycle Heavy Normal or Water Saver 7 Be sure the door is unlatched Slowly turn the Dial to the cycle you want Don t turn it past this position or you could accidentally miss a rinse 3 Select any options 4 Latch the door to start the cycle Short Wash For quickly washing loads of everyday dishes with medium soils that have not dried on 7 Be sure the door is unlatched 2 Slowly turn the Dial to SHORT WASH 3 Latch the door to start the cycle Using the dishwasher Check the Water Temperature The entering water must be at least 120 F and not more than 150 F for effective cleaning and to prevent dish damage Check the water temperature with a candy or meat thermometer Use Jet Dry Rinse Agent
15. d S Screw Type Clamps C UL Listed Wire nuts 3 90 Elbow For new installations only lt J Air gap for drain hose if required ex Waste tee for house plumbing if applicable J Electrical cable or power cord if applicable oe Thread Seal 2 en St Relief LJ Screw type hose clamps Te Tape Wire Nuts OS LJ Strain relief for electrical connection LJ Hand shut off valve recommended L Air Shut Off L Water line 3 8 min copper or 1 2 min plastic Gap b Valve L Coupler for extending drain line if applicable Coupler TOOLS YOU WILL NEED Tools required Flat Blade Screwdriver C 0 p gt C Phillips head and flat blade screwdrivers SSS C Adjustable wrench 6 Flashlight Ts C Level As Saw Set pees Phillips Head C Carpenters square ZEE LI Massuringitape aun e Screwdriver Safety glasses Safety Glasses LJ Flashlight Tubing Bg S Adjustable Cutter znd Bis N For new installations only Wrench N O Tubing cutter CJ Drill and appropriate bits C Hole saw set Square Measuring Tape PREPARE DISHWASHER ENCLOSURE The rough cabinet opening must have a minimum width and depth of 24 and approximately 34 1 2 high from floor to underside of the countertop Figure A The back wall should be free of pipes or wires Figure A Adjacent cabinets should be square and plumb to ensure a good fit Figure A For corner installation allow 2 min clearance between dishwasher and adjacent cabinet
16. dimensional data circuit having 2 wire service with a separate ground wire This appliance must be grounded for safe operation lunge A As an ENERGY STAR Partner GE has determined that this product Specification Created 1 02 meets the ENERGY STAR guidelines for energy efficiency Listed by L Underwriters Laboratories HOTPOINT HDA3400G Hotpoint Built In Dishwasher Specification Created 1 02 Features and Benefits e Energy Star Qualified e Power Wash II System with Self Cleaning Filter and 3 Wash Levels e Dial Controls with Pushbuttons e Deluxe Plus Upper Rack e Deluxe Lower Rack e Deluxe Silverware Basket e 5 Cycle 22 Option Selections Pots amp Pans Normal Wash Water Saver Dial Plate Warmer Dial Rinse Only Dial Heated Dry Rocker Hi Temp Wash and Hot PreWash Option Dial e Rinse Aid Dispenser e Steel Door e QuietPower Motor e Standard Sound Insulation Package e Model HDA3400GWW White on white e Model HDA3400GBB Black on black
17. e you call for service Hotpoint com Troubleshooting Tips Save time and money Review the charts on the following pages or visit Hotpoint com You may not need to call for service Problem Dishwasher Possible Causes Fuse is blown or the What To Do Replace fuse or reset circuit breaker Remove any other appliances won t run Noise circuit breaker tripped Some of the sounds from the circuit Soft food disposal shredding action Water standing in the bottom of the tub you ll hear are normal Drain valve opening to pump water out Timer control as cycle progresses Detergent cup opening The motor stopping during the drying period Utensils are not secure in the rack or something Make sure everything is secured in dishwasher small has dropped into the rack Motor hums Dishwasher has not been used on a regular basis If you do not use your dishwasher often set it to fill and pump out once every week This will help keep the seal moist and the garbage disposer clear This is normal A small amount of clean water around the outlet on the tub bottom at the back of the tub keeps the water seal lubricated Drain is clogged If you have an air gap clean it Water won t pump out of the tub Suds in the tub Stained tub interior Correct detergent wasn t used Check to see if your kitchen sink is draining well If not you may need a plumber If
18. either Method 1 or Method 2 may be used Figure C or Figure D A CAUTION An air gap MUST BE USED if the drain hose is connected to waste tee or disposer lower than 18 above the floor level Failure to provide the proper drain connection height with air gap or 32 minimum high drain loop will result in improper draining of the dishwasher which may cause damage METHOD 1 Air Gap with Waste Tee or Disposer 0 0d00 Tg A B Waste Tee Installation Disposer Installation Figure C METHOD 2 High Drain with Waste Tee or Disposer Provide a method to attach drain hose to underside of countertop Attachment will be made in a later step Waste Tee Installation Figure D Disposer Installation Install waste tee or disposer and air gap according to manufacturer s instructions CABINET PREPARATION Drill 1 1 2 inch diameter hole in the cabinet wall within the shaded area shown in Figure A for the drain hose Make sure there are no sharp edges Drain hose will be passed through this hole and connected to the drain in a later step LET MEME ELECTRICAL WIRING ily WARNING Gy FOR PERSONAL SAFETY REMOVE HOUSE FUSE OR OPEN CIRCUIT BREAKER BEFORE BEGINNING INSTALLATION DO NOT USE AN EXTENSION CORD OR ADAPTER PLUG WITH THIS APPLIANCE ELECTRICAL REQUIREMENTS This appliance must be supplied with 120V 60 Hz and connected to an individual properly grounded branch circuit protected by a 15 or 20 ampe
19. gistration Department P O Box 32150 Louisville KY 40232 2150 13 Consumer Product Ownership Registration Dear Customer Thank you for purchasing our product and thank you for placing your confidence in us We are proud to have you as a customer Follow these three steps to protect your new appliance investment Complete and mail After mailing the Read your Owner s your Consumer registration below Manual carefully Product Ownership store this document It will help you Registration today in a safe place It operate your new Have the peace of contains information appliance properly mind of knowing we can contact you in the unlikely event of a safety modification you will need should you require service Our service number is 800 GE CARES 800 432 2737 Model Number Serial Number Important If you did not get a registration card with your product detach and return the form below to ensure that your product is registered or register online at Hotpoint com Cut here Consumer Product Ownership Registration Model Number Serial Number m Mr Ms Mrs Miss d Name Name Street Address l l l l l Apt E mail Address City State Gods Dale Maced uae Month Day Year Number l Please provide your e mail address to receive via e mail discounts speci
20. imum of 24 from the rear wall e For power cord connections install a 3 prong grounding type receptacle in the rear wall of sink cabinet next to the dishwasher The receptacle should be installed at least 6 but not more than 18 from the cabinet opening for dishwasher PREPARE HOT WATER LINE HOT WATER LINE The hot water line may enter from either side the rear or from the floor within the shaded area shown in Figure F Cut a hole approximately 1 1 2 dia within the shaded area to admit the line N 49 Turn off the water supply S but recommended and may be required by local codes Water connection is on left side of dishwasher Install the hot water inlet line using no less than 3 8 O D copper tubing or ca 1 2 O D plastic tubing Route line as shown in Figure F Extend the water line forward at least 19 from rear wall e Adjust the water heater to deliver water between the temperatures of 120 F and 150 F 7 Flush water line to clean out debris 8 The water pressure of the hot water supply line must be 20 120 PSI Install a hand shut off valve in the supply line in an accessible location such as under the sink The shut off valve is optional 19 From Wall Pis From Floor Cabinet Face Figure F INSTALLATION INSTRUCTIONS A CAUTION Do not remove the wood base until you are ready to install the dishwasher The dishwasher will tip over when the d
21. is left in an unheated place during the winter ask a service technician to Cut off electrical power to the dishwasher Remove fuses or trip circuit breaker Turn off the water supply and disconnect the water inlet line from the water valve Does Your Dishwasher Have an Air Gap An air gap protects your dishwasher against water backing up into it if a drain clogs The air gap is not a part of the dishwasher It is not covered by your warranty Not all plumbing codes require air gaps so you may not have one Drain water from the inlet line and water valve Use a pan to catch the water Reconnect the water inlet line to the water valve Remove the plastic sump cover in the tub bottom and use a sponge to soak up water in the rubber boot The air gap is easy to clean 7 Turn off the dishwasher and lift off the chrome cover Unscrew the plastic cap and clean with a toothpick suononysuy Ajajeg E m 3 e LI A S Q E S 77 sdij Burjooisa qnoa yioddns saunsuoy Safety Instructions L S S D E IS 3 e Troubleshooting Tips Consumer Support About optional accessories You can change the door and lower access panel appearance of your dishwasher by ordering one of these optional accessories Color Panels 1 4 Wood Panel Trim Kit 3 4 Trimless Wood Panel Kit Descriptions of Optional Accessories These accessories are available at extra cost VISA Maste
22. ishes with medium soils that have not dried on such as loads consisting mostly of glasses WATER SAVER For dishes with light soils RINSE ONLY For rinsing partial loads that will be washed later Do not use detergent PLATE WARMER For warming clean dishes and serving plates This cycle will take approximately 30 minutes HOT PREWASH Preheats wash water to the correct temperature Adds 1 5 gal and 30 min RINSE to the start of the selected cycle Energy Options HI TEMP Provides extra heat for best performance It is used best with heavily soiled dishes WASH ON HI TEMP WASH HI TEMP Turns HI TEMP WASH off WASH OFF HEATED DRY Turns the heating element on for fast drying This option will extend the time of your wash cycle HEATED DRY ON Available on all wash cycles except RINSE ONLY Adds approx 32 minutes to the cycle gt m 3 e LI A S Q FE S 77 HEATED DRY OFF Turns HEATED DRY off Dishes air dry naturally and energy is saved Start Slowly turn the Dial to the START or ON position or the selected cycle Don t turn it past the START ON or cycle position or you could accidentally miss a rinse There is a time delay between start up and water fill so you will not hear any wash action right away Latch the door to begin the cycle Cycle Chart Model Cycle Water Usage gal Cycle Time min Hot PreWash Option 3 4 26 HDA1000 Normal Wash 8 4 71 Drying Plate Warmer H
23. l 800 626 2224 during normal business hours Hotpoint Consumer Home Services will still be there after your warranty expires Parts and Accessories Hotpoint com Individuals qualified to service their own appliances can have parts or accessories sent directly to their homes VISA MasterCard and Discover cards are accepted Order on line today 24 hours every day or by phone at 800 626 2002 during normal business hours Instructions contained in this manual cover procedures to be performed by any user Other servicing generally should be referred to qualified service personnel Caution must be exercised since improper servicing may cause unsafe operation Contact Us Hotpoint com KoA If you are not satisfied with the service you receive from Hotpoint contact us on our Website with all the details including your phone number or write to General Manager Customer Relations Hotpoint Appliance Park Louisville KY 40225 Register Your Appliance Hotpoint com Register your new appliance on line at your convenience Timely product registration will allow for enhanced communication and prompt service under the terms of your warranty should the need arise You may also mail in the pre printed registration card included in the packing material s Printed in the United States Ww Printed on Recycled Paper HOTPOINT HDA3400G Hotpoint Built In Dishwasher
24. loudiness of glassware called etching You ll find two detergent dispensers on the inside door of your dishwasher All wash cycles require detergent in the main cup Wash cycles with two washes will also use the open cup When using automatic dishwashing detergent tabs simply place one tab in the main cup and close Be sure the Dial is OFF before adding detergent Otherwise the detergent cup will not close and latch properly Add detergent then close the main cup NOTE To open detergent cup after it has been closed simply turn the detergent cup handle counterclockwise until it releases A snapping sound may be heard DO NOT USE HAND DISH DETERGENT NOTE Using a detergent that is not specifically designed for dishwashers will cause the dishwasher to fill with suds During operation these suds will spill out of the dishwasher vents covering the kitchen floor and making the floor wet Because so many detergent containers look alike store the dishwasher detergent in a separate space from all other cleaners Show anyone who may use the dishwasher the correct detergent and where it is stored While there will be no lasting damage to the dishwasher your dishes will not get clean using a dishwashing detergent that is not formulated to work with dishwashers suononysuy Ajajeg gt m 3 e LI A S Q E S 77 sdij Burjooisa qnoa pioddns sauinsuoy V1 NY o Safety Instruction
25. maintenance NOTE Turning the dishwasher off does not BI Use supply conductors rated at least 75 C disconnect the appliance from the power supply 167 F We recommend having a qualified technician service your appliance A WARNING DO NOT B Do not allow children to play around dishwasher when opening or closing door due to the possibility of small fingers being pinched in door B Do not tamper with controls E Do not abuse sit on or stand on the door or dish rack of the dishwasher B Do not allow children to play with on or around E Do not discard a dishwasher without first thi i is appliance or any discarded appliance removing the door of the washing compartment E Do not store or use combustible materials gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance Hotpoint com WARNING RISK OF CHILD ENTRAPMENT PROPER DISPOSAL OF THE DISHWASHER Junked or abandoned dishwashers are dangerous even if they will sit for just a few days If you are getting rid of your old dishwasher please follow the instructions below to help prevent accidents suon nysuj Ajajeg Before You Throw Away Your Old Dishwasher E Take off the door of the washing compartment or remove the door latch keeper as shown m 3 Q 2 S ge S o WHEN USING YOUR DISHWASHER BI Use only powder tabs liquid detergents or E Non Dishware Items Do n
26. nd slide the door latch to the left Reposition the dishes e Steam comes through the vent by the door latch during drying and when water is being pumped out Remove marks with a mild abrasive cleaner GE Service Protection Plus GE a name recognized worldwide for quality and dependability offers you Service Protection Plus comprehensive protection on all your appliances No Matter What Brand Benefits Include Backed by GE We ll Cover Any Appliance All brands covered Unlimited service calls An y wh ere An yt me m All parts and labor costs included No out of pocket expenses No hidden deductibles One 800 number to call You will be completely satisfied with our service protection or you may request your money back on the remaining value of your contract No questions asked It s that simple Protect your refrigerator dishwasher washer and dryer range TV VCR and much more any brand Plus there s no extra charge for emergency service and low monthly financing is available Even icemaker coverage and food spoilage protection is offered You can rest easy knowing that all your valuable household products are protected against expensive repairs Place your confidence in GE and call us in the U S toll free at 800 626 2224 for more information AII brands covered up to 20 years old in the continental U S Please place in envelope and mail to General Electric Company Warranty Re
27. oor is opened Step 1 Check door balance before wood base is removed Locate the 2 Phillips head countertop mounting screws wrapped with yellow tape and stuck to the top or side of the dishwasher Set aside for use in Step 12 Check door balance by opening and closing door If neces sary latch door and adjust one or both springs before the wood base is removed Moving spring hook to rear hole increases spring tension Insert Spring Hook Through Inside of Frame Step 2 Remove leveling legs and wood base Move the dishwasher close to the cabinet and lay it on its back Remove the four leveling legs with an adjustable wrench Remove and discard the wood base Do not Kick wood base off damage will occur Figure G Step 3 Install leveling legs Screw leveling legs back into the dishwasher frame The legs should extend approximately 3 4 away from the frame If you need help with any of the following steps call the GE Answer Center Consumer Information Service 800 626 2000 Step 4 Remove access panel and toekick Remove the two screws below the access panel and set aside for reuse Remove access panel by backing out the two screws located between the door and access panel These screws are secured to access panel with plastic retainers Back Out Remove 2 Screws Figure Step 5 install power cord when used For power cord in
28. or wall or other appliances Figure B Countertop Dishwasher Figure B Clearance for Door Opening 2 Minimum PREPARE DRAIN PLUMBING This Wall Area must be Free of Pipes or wires 34 1 2 1 4 Underside of Countertop to Floo Cabinets Square and Plumb Figure A Min Make sure the floor is level inside the opening and even with the finished floor of the kitchen e The dishwasher must be installed no more than 10 feet from sink for proper drainage This dishwasher must be fully enclosed on the top sides and back The dishwasher must not support any part of the enclosure DRAIN REQUIREMENTS Follow local codes and ordinances Dishwasher drain hose must not exceed 10 feet in length for proper drainage Dishwasher must be connected to waste line with an air gap not supplied or 32 minimum high drain loop depend ing on local codes and ordinances to prevent back flow into the dishwasher Air gap must be used if waste tee or disposer connection is less than 18 inches above floor to prevent siphoning DRAIN PREPARATION The type of drain installation depends on answers to the following questions C Do local codes or ordinances require an air gap C Will waste tee or disposer connection be less than 18 above floor C Will installation have a drain loop less than 32 above floor If the answer to ANY ofthe 3 questions above is YES Method 1 MUST be used Otherwise
29. ot PreWash Option Normal Wash Rinse Only Drying Plate Warmer Hot PreWash Opti Heavy Wash Normal Wash Water Saver Rinse Only Drying Plate Warmer sdij Burjooisa qnoa HDA1200 HDA2000 Hot PreWash Option Heavy Wash Normal Wash Water Saver Rinse Only Drying Plate Warmer HDA3400 Hot PreWash Option Pots amp Pans Heavy Wash HDA3700 Normal Wash Water Saver Rinse Only Drying Plate Warmer yioddns saunsuoy Normal cycle needs to be selected 5 Safety Instructions L S S D SS 3 Q Troubleshooting Tips Consumer Support About the dial cycles HOT PREWASH OPTION te DELAY Beh 8o e START wee 5 SHORT WASH OFFe PLATE WARMER HEATED DRY ON D RINSE ONLY Ld HEATED DRY OFF HOT PREWASH OPTION te DRY HOURS 3 dj s snm Nie 5 SHORT WASH OFF e PLATE WARMER eaten DY Of RINSE ONLY HEATED DRY OFF HOT PREWASH OPTION le DELAY HOURS g o SETAT AG 5 SHORT WASH orFe PLATE WARMER HEATED DRY ON RINSE ONLY HEATED DRY OFF e HEAVY WASH NORMAL WASH WATER SAVER DRYING RINSE ONLY cre oram HOT PREWASH OPTION te DELAY HOURS 3 ro srun nas 5 SHORT WASH OFF e PLATE WARMER DRY ON RINSE ONLY HEATED DRY OFF Rinse Only For rinsing partial loads that will be washed later Do not use detergent 7 Make sure ENERGY SAVER HEATED DRY OFF is selecte
30. ot connect water and electrical in this step Step 11 Level dishwasher Level the dishwasher by adjusting the four leveling legs individually for correct alignment See Figure 0 Dishwasher should be level left to right and front to back for proper dish rack operation and dishwasher performance Dishwasher door should be in alignment with adjacent cabinets See Figure P Figure 0 Step 12 Position dishwasher and fasten to cabinet Open the door and position the dishwasher tub flange 3 4 from the cabinet opening Fasten the dishwasher to the underside of the countertop using the 2 Phillips screws provided in Step 1 Be sure screws are driven straight and flush to avoid interference with door operation See Figure P Important Make sure that dishwasher is centered in the opening and there is no interference with cabinets when opening or closing the door Interfer ence may cause a water leak when dishwasher is in operation Figure P INSTALLATION INSTRUCTIONS continued Step 13 connect water supply Connect water supply line to 90 elbow installed in Step 6 Open and close the door Check to be sure door spring does not rub against fill hose or water supply line Important When opening and closing the door the door spring should not touch the fill hose If it does bend water valve bracket slightly to provide clearance between the spring and the fill hose
31. ot wash items such rinse agents recommended for use in a as electronic air cleaner filters furnace filters dishwasher and keep them out of the reach and paint brushes in your dishwasher Damage of children Cascade Cascade Complete and to dishwasher and discoloration Electrasol Automatic Dishwashing or staining of dishwasher may result Detergents and Jet Dry rinse agent have been approved for use in all GE dishwashers E Do not touch the heating element during or immediately after use E Locate sharp items so that they are not likely to damage the door seal E Do not operate your dishwasher unless all enclosure panels are properly in place B Load sharp knives with the handles up to ot as E Close supervision is necessary if this appliance reduce the risk of cut type injuries P S PP is used by or near children E Do not wash plastic items unless marked dishwasher safe or the equivalent For plastic items not so marked check the manufacturer s recommendations B Load light plastic items so they will not become dislodged and drop to the bottom of the dishwasher they might come into contact with the heating element and be damaged sdij Burjooisa qnoa pioddns saunsuoy About the dishwasher control panel You can locate your model number on the tub wall just inside the door Throughout this manual features and appearance may vary from your model Model HDA1000 HOT PREWASH OPTION e NORMAL WASH H
32. poons and lids from small containers should go in the bottom of the silverware basket with silverware on top Hotpoint com 2 Once the water calms open the door Steam may rise out of the dishwasher Secure larger dishwasher safe plastics over two fingers when possible Make sure small plastic items are secure so they cant fall onto the heating element Don t block it or load tall things next to it Also be careful not to let a portion of an item such as a pot or dish handle extend through the bottom rack This could block the wash arm and cause poor washing results The lower rack is best used for plates saucers and cookware Large items such as broiler pans and racks should go along the sides Load platters pots and bowls along the sides in corners or in the back The soiled side of items should face the center of the rack A security cell cover on some models can be lowered to either side to secure f lightweight items from the effects of the vigorous wash action Caring for the dishwasher Hotpoint com To clean the control panel use a lightly dampened cloth then dry thoroughly To clean the exterior use a good appliance polish Never use sharp objects scouring pads or harsh cleaners on any part of the dishwasher ANS AF Sump cover screws Two types of air gaps Check the air gap any time your dishwasher isn t draining well Protect Against Freezing If your dishwasher
33. r any labor or in home From the date of the service costs original purchase Ten Years Only The PermaTuf tub or door liner if it fails to contain water due to a defect in materials or for models HDA2000 workmanship During this full warranty GE will also provide free of charge all labor and HDA3400 and HDA3700 in home service to replace the defective part From the date of the original purchase What Is Not Covered H Service trips to your home to teach you how to use the E Damage to the product caused by accident fire floods or product acts of God Bi Improper installation H Incidental or consequential damage caused by possible H Failure of the product if it is abused misused or used for other than the intended purpose or used commercially defects with this appliance ll Cleaning or servicing of the air gap device in the drain line E Replacement of house fuses or resetting of circuit breakers This warranty is extended to the original purchaser and any succeeding owner for products purchased for home use within the USA In Alaska the warranty excludes the cost of shipping or service calls to your home Some states do not allow the exclusion or limitation of incidental or consequential damages This warranty gives you specific legal rights and you may also have other rights which vary from state to state To know what your legal rights are consult your local or state consumer affairs office or your state s Attorne
34. rCard or Discover cards accepted by calling 800 626 2002 Specify accessory number when ordering Wood panel trim kit This accessory contains trim and instructions for you to supply and install a 1 4 thick decorative wood door and lower access panel For models HDA1000 HDA2000 HDA3400 GPF325A Almond GPF325B Black HDA3700 GPF425A Almond GPF425C Bisque GPF425B Black GPF425W White NOTE The GPF100 dishwasher door spring kit must also be ordered and installed when the door panel weighs four Ibs or more GPF325C Bisque GPF325W White About rack accessories For best results the Baby Bottle Holder should be installed on the upper rack of the dishwasher 10 Baby Bottle Holder Part Number WX69X200 dishwasher cycle Snaps easily onto any dishwasher upper rack Eliminates hand washing Fits all baby bottles Prevents movement of baby bottles during the Trimless wood panel kit This accessory contains parts and instructions for you to supply and install a 3 4 thick decorative wood door and lower access panel For models HDA1000 HDA2000 HDA3400 GPF375 HDA3700 GPF475 NOTE The GPF100 dishwasher door spring kit will be included with the trimless wood panel kitand must be installed with it You can order a package of 5 Baby Bottle Holders at extra cost by calling 800 626 2002 or through the Internet at GEAppliances com Visa MasterCard or Discover cards accepted Befor
35. ration of the dishwasher Add two quarts of water to the bottom of the dishwasher to lubricate the pump seal Remove the protective film if present from the control panel access panel and door panel LJ Check to be sure that wiring is secure under the dish washer and not pinched or in contact with door springs or other dishwasher components LJ Pull lower rack about half way out Check to be sure it does not roll back into dishwasher or further out If it does relevel dishwasher Turn on water supply Check for plumbing leaks Tighten connections if necessary LJ Check that door spring does not contact water line fill hose wiring or dishwasher components J Turn on the hot water faucet at the sink and verify water temperature Water going to dishwasher must be between the temperatures of 120 F and 150 F Step 17 Dishwasher wet test check list Turn on power supply Latch door Select normal cycle on push button or electronic models On dial models turn control dial just enough to start dishwasher Be careful not to turn the dial past the first water fill On electronic models push start pad C Check to be sure that water enters the dishwasher This could take up to 4 minutes If water does not enter the dishwasher check to be sure that water is turned on C Check for leaks under the dishwasher If a leak is found turn off power supply tighten connections and restore power
36. re circuit breaker or time delay fuse Wiring must be 2 wire with ground If the electrical supply provided does not meet the above requirements call a licensed electrician before proceeding GROUNDING INSTRUCTION This appliance must be connected to a grounded metal permanent wiring system or an equipment grounding conduc tor must be run with the circuit conductors and be connected to the equipment grounding terminal or lead on the appliance iy A WARNING 7 THE IMPROPER CONNECTION OF THE EQUIPMENT GROUNDING CONDUCTOR CAN RESULT IN A RISK OF ELECTRIC SHOCK CHECK WITH A QUALIFIED ELECTRICIAN OR SERVICE REPRESENTATIVE IF YOU ARE IN DOUBT WHETHER THE APPLIANCE IS PROPERLY GROUNDED Alternate Receptacle l Receptacle l ILocation I 18 Area B 1 e 24 from Wal Ground 7 Black Figure E White CABINET PREPARATION amp WIRE ROUTING Wiring may enter from either side the rear or from the floor within the shaded area shown in Figure E Cut hole 1 1 2 max dia within the shaded area to admit the electrical cable or power cord The hole must be free of sharp edges If the cabinet wall partition is metal the edge of the hole must be covered with a rubber protector ELECTRICAL CONNECTIONS TO DISHWASHER Electrical connection is on right side of dishwasher For cable direct connections the cable must be routed as shown in Figure E Cable must extend a min
37. s may vary from your model Operating Instructions Troubleshooting Tips Consumer Support Don t let any item extend through bottom L Forget to Add a Dish O A forgotten dish can be added any time before the main wash Caring for the dishwasher 7 Push the door latch to the left 3 Add forgotten dishes 4 Close the door and push the latch to the far right Loading the dishwasher racks For best dishwashing results follow these loading guidelines Features and appearance of racks and silverware baskets Upper Rack The upper rack is for glasses cups and saucers Cups and glasses fit best along the sides This is also a secure place for dishwashersafe plastics The upper rack is good for all kinds of odd shaped utensils Saucepans mixing bowls and other items should be placed face down Wash Tower Keep the center area clear in the lower rack The wash tower rises through the center of the lower rack during the wash and rinse portions of the cycle Lower Rack When loading the lower rack do not load large platters or trays in the front right corner They may prevent detergent from circulating during the wash cycle Silverware Basket Put flatware in the removable basket with fork and knife handles up to protect your hands Place spoons in the basket with handles down Mix knives forks and spoons so they don t nest together Distribute evenly Small plastic items such as measuring s
38. stallation only Skip this step if dishwasher will be directly wired Remove the junction box Note Check That Harness Leads Are cover and install strain Threaded Thru Small Hole in Bracket relief The power cord White and connections must Neutral comply with the National rund Electrical Code Section 422 and or local codes and ordinances The cord must be no longer than 6 ft from the junction box to the receptacle Locate the three dish washer wires white black and green with the stripped ends Using UL Listed wire nuts of appropriate size connect incoming white to white black to black and incoming ground to green wire Replace the junction box cover Check that wires are not pinched under cover Step 6 install 90 elbow Install the 90 elbow fitting to the water valve using thread seal tape on the threads The water valve requires 3 8 NPT fitting with external threads The opposite end should fit water supply line Position the end of the elbow to face the rear of the dishwasher Do not bend the dishwasher frame when installing the 90 elbow fitting to the water valve as this could cause the door spring to come in contact with the fill hose Figure K INSTALLATION INSTRUCTIONS continued Step 7 Position water line and power supply Position the water supply line and house wiring on the floor of the opening to avoid interference with base of dishwasher and
39. veral minutes Do this before using any electrical appliance which is connected to the hot water system This simple procedure will allow any builtup hydrogen gas to escape Since the gas is flammable do not smoke or use an open flame or appliance during this process Use this appliance only for its intended purpose as described in this Owner s Manual PROPER INSTALLATION AND MAINTENANCE This dishwasher must be properly installed and located in accordance with the Installation Instructions before it is used If you did not receive an Installation Instructions sheet with your dishwasher you can receive one by visiting our website at Hotpoint com ll Connect to a grounded metal permanent wiring W Dispose of discarded appliances and shipping system or run an equipmentgrounding or packing material properly conductor with the circuit conductors and connect to the equipmentgrounding terminal or lead of the appliance E Do not attempt to repair or replace any part of your dishwasher unless it is specifically recommended in this manual All other servicing E Improper connection of the equipment should be referred to a qualified technician grounding conductor can result in a risk of electric shock Check with a qualified electrician or service representative if you are in doubt whether the appliance is properly grounded B To minimize the possibility of electric shock disconnect this appliance from the power supply before attempting any
40. y General Warrantor General Electric Company Louisville KY 40225 15 suononysuy Ajajeg m 3 Q 2 S ge S 7 sdij Burjooisa qnoa pioddngs 10umnsuo Consumer Support Hotpoint Website Hotpoint com Have a question or need assistance with your appliance Try the Hotpoint Website 24 hours a day any day of the year You can also shop for more great Hotpoint products and take advantage of all of our on line support services designed for your convenience Schedule Service Hotpoint com Expert Hotpoint repair service is only one step away from your door Get on line and schedule your service at your convenience 24 hours any day of the year Or call 800 GE CARES 800 432 2737 during normal business hours Real Life Design Studio GEAppliances com GE supports the Universal Design concept products services and environments that can be used by people of all ages sizes and capabilities We recognize the need to design for a wide range of physical and mental abilities and impairments For details of GE s Universal Design applications including kitchen design ideas for people with disabilities check out our Website today For the hearing impaired please call 800 TDD GEAC 800 833 4322 Extended Warranties GEAppliances com Purchase a Hotpoint extended warranty and learn about special discounts that are available while your S warranty is still in effect You can purchase it on line anytime or cal
Download Pdf Manuals
Related Search