ZyXEL Communications 100 Network Card User Manual
Contents
1. of the Domain Name System server s if supplied by your ISP Preparing Your Network Ge BN All computers must have a 10M or 100M NIC Network Interface Card and TCP IP installed TCP IP should already be installed on computers using Windows NT 2000 XP Macintosh OS 7 and later operating systems These procedures are for dynamic IP addresses Setting up Your Windows 95 98 Me Computer Installing TCP IP Components 1 Click Start Settings Control Panel and double click the Network icon 2 The Network window Configuration tab displays a list of installed components To install TCP IP a In the Network window click Add b Select Protocol and then click Add c Select Microsoft from the list of manufacturers d Select TCP IP from the list of network protocols and then click OK Configuring TCP IP 1 In the Network window Configuration tab select your network adapter s TCP IP entry and click Properties 2 Click the IP Address tab Click Obtain an IP address automatically 3 Click the DNS Configuration tab Select Disable DNS 4 Click the Gateway tab Highlight any installed gateways and click Remove until there are none listed 5 Click OK to save and close the TCP IP Properties window 6 Click OK to close the Network window 7 Turn on your ZyWALL and restart your computer when prompted Insert the Windows CD if prompted Verifying TCP IP Properties 1 Click Start and then Run In the Run window type wini2. Refer to the Cable Connections section for details not come on Make sure your NIC Network Interface Card is installed and functioning properly Cannot access the The default password is 1234 If you have changed the password and have now forgotten it you will need web configurator to upload the default configuration file see the User s Guide If you cannot get to the web configurator login screen Make sure that there is not an SMT console session running Check if you have applied a filter in SMT menu 3 1 LAN or menu 11 5 WAN to block web service Check that you have enabled web service access in SMT Menu 24 11 Remote Management Control For WAN access you must configure the Server Access field to ALL Otherwise the firewall when activated blocks all WAN to LAN traffic by default If you have configured an IP address in the Secured Client IP field your computer s IP address must match it For access from the LAN check your computer s TCP IP configuration The IP address and the subnet mask of the ZyWALL and your computer must be on the same subnet Cannot ping any computer on the LAN If the 10 100M LAN LEDs are off check the cables between the ZyWALL and your computer or hub Verify that the IP address and the subnet mask of the ZyWALL and the computers are on the same subnet Cannot get a WAN IP address from the ISP The WAN IP is provided after the ISP verifies the MAC address ho
3. Panel and double click TCP IP to open the TCP IP Control Panel 2 Select Ethernet from the Connect via list 3 Select Using DHCP Server from the Configure list 4 Close the TCP IP Control Panel 5 Click Save if prompted to save changes to your configuration 6 Turn on your ZyWALL and restart your computer if prompted Verifying TCP IP Properties Check your TCP IP properties in the TCP IP Control Panel Accessing the ZyWALL 1 Web configurator 2 SMT System Management Terminal Access the SMT via e Telnet e Console port using terminal emulation software Procedure For Web Configurator Configuration 1 Launch your web browser and enter 192 168 1 1 as the URL 2 Type 1234 default as the password and press ENTER 3 You should now see the Main Menu screen Click the help icon located in the upper right portion of most screens for online HTML help Procedure For SMT Configuration via Telnet 1 Launch a Telnet program In Windows click Start and then Run 2 Type Telnet followed by a space and the IP address of the ZyWALL 192 168 1 1 is the default and click OK to display the password screen 3 Enter 1234 the default password to access the SMT main menu As you type a password the screen displays an X for each character you type Procedure For SMT Configuration via Console Port 1 Configure a terminal emulation communications program as follows VT100 terminal emulation no parity 8
4. ZyWALL 100 Read Me First WALL OUTLET COMPUTERs SERVERs Rear Panel Connections PORT CONNECTION CONSOLE Connect to your computer s com port using a console cable WAN 10 100M Connect to a cable xDSL device using an Ethernet cable DIAL BACKUP Connect to an analog or ISDN device using a console RS 232 cable POWER Connect the power cord to the ZyWALL and plug it into an appropriate power outlet TO A COMPUTER TO A HUB DMZ Crossover Ethernet cable Straight through Ethernet cable LAN 10 100M UPLINK button on pushed in Straight through Ethernet cable Crossover Ethernet cable LAN 10 100M UPLINK button off out Crossover Ethernet cable Straight through Ethernet cable WIRELESS LAN Use a ZyXEL Wireless PC Card to connect to a wireless LAN Register your ZyWALL online at www zyxel com for free product updates and information Before You Start ZYWALL FACTORY DEFAULTS IP Address 192 168 1 1 Subnet Mask 255 255 255 0 Password 1234 DHCP IP Pool 192 168 1 33 192 168 1 64 Network Access Checklist You need a broadband modem and an account with an Internet Service Provider ISP Your user account name and password Encapsulation Ethernet PPTP or PPPoE You may need to know your Service Name if you are using PPTP or PPPoE Service type when using Ethernet Standard RR Toshiba RR Manager or RR Telstra The IP address es
5. data bits 1 stop bit data flow set to none 9600 bps port speed 2 Press ENTER to display the SMT password screen The default password is 1234 Use the ISP information you gathered to configure SMT menu 4 and access the Internet Refer to your User s Guide for details Troubleshooting Before performing troubleshooting make sure both the ZyWALL s power PWR LED and the system status SYS LED are on See the User s Guide for more information about the SMT menus In the web configurator click the help icon PROBLEM CORRECTIVE ACTION The PWR LED is off Make sure that the ZyWALL s power cord is connected to the ZyWALL and plugged in to an appropriate power source Check that the ZyWALL and the power source are both turned on If the error persists you may have a hardware problem In this case you should contact your vendor The SYS LED is off Turn the ZyWALL s power off and then on again Cannot access the Make sure the ZyWALL is connected to your computer s serial port ZyWALL via the rae ee console port Check to see if the communications program is configured correctly The communications software should be configured as follows gt VT100 terminal emulation no parity 8 data bits 1 stop bit data flow set to none gt 9600 bps is the default speed on leaving the factory Try other speeds in case the speed has been changed The LAN LED does Check your Ethernet cable type and connections
6. pcfg and then click OK to open the IP Configuration window 2 Select your network adapter You should see your computer s IP address subnet mask and default gateway Setting up Your Windows NT 2000 XP Computer Configuring TCP IP 1 Click Start Settings Network and Dial up Connections and right click Local Area Connection or the connection you want to configure and click Properties For Windows XP click start Control Panel Network and Internet Connections and then Network Connections Right click the network connection you want to configure and then click Properties 2 Select Internet Protocol TCP IP under the General tab in Win XP and click Properties 3 The Internet Protocol TCP IP Properties window opens Click Obtain an IP address automatically 4 Click Obtain DNS server automatically 5 Click Advanced IP Settings tab and remove any installed gateways then click OK 6 Click OK to save and close the Internet Protocol TCP IP Properties window 7 Click OK to close the Local Area Connection Properties window 8 Turn on your ZyWALL and restart your computer if prompted Verifying TCP IP Properties 1 Click Start Programs Accessories and then Command Prompt 2 Inthe Command Prompt window type ipconfig and then press ENTER The window displays information about your IP address subnet mask and default gateway Setting up Your Macintosh Computer Configuring TCP IP Properties 1 Click the Apple menu Control
7. st name or user ID Find out the verification method used by your ISP and configure the corresponding fields If the ISP checks the WAN MAC Address and does not allow you to use a new MAC clone a MAC from the LAN In the SMT use menu 2 In the web configurator click ADVANCED WAN and then the MAC tab ZyXEL recommends that you configure this menu even if your ISP presently does not require MAC address authentication If the ISP checks the host name enter your computer s name as the system name in SMT menu 1 or in the first screen of the web configurator s WIZARD SETUP If the ISP checks the user ID check your service type user name and password In the SMT use menu 4 In the web configurator click ADVANCED WAN and the ISP tab Cannot access the Internet Make sure the cable xDSL device is turned on and connected to the ZyWALL and the Internet If the ZyWALL s WAN LED is not on check the cable between the ZyWALL and the cable xDSL device Check whether your cable xDSL device requires a crossover or straight through cable Verify your settings in SMT menus 2 and 4 In the web configurator click ADVANCED and then WAN
Download Pdf Manuals
Related Search