Xantech HDMI4X4 Switch User Manual
Contents
1. 1 Determine the minimum amplifier impedance typically either 4 or 8 Ohm This information can usually be found next to the speaker outputs located on the receiver or amplifier If in doubt consult the receiver and or amplifier instruction manual 2 Next determine the impedance of a single speaker that will be used Use the left most column 3 Move to the right of the chart and find the number of speaker pairs that you plan to connect to the volume control 4 Finally move up the column to the very top row This row will provide the jumper setting solution Change the jumper on the volume control to complete the impedance jumper setting procedure Both jumpers must be changed appropriately see diagram in Fig 1 Jumper Settings X2 x4 x8 A a 1 PAIR 2 PAIRS 4 PAIRS 8 PAIRS NN 1PAIR 2PAIRS 4 PAIRS CHART A 8 Ohm Minimum Amplifier Speaker Impedance Jumper Settings x8 x1 x2 x4 1 PAIR 4 PAIR 8 PAIRS 2 PAIRS 4 PAIRS 8 PAIRS Ohm CHART B 4 Ohm Minimum Amplifier o 59 G CO og Q o Og Example 1 Two pairs of 8 Ohm ceiling speakers are to be used with two volume controls all driven by a single amplifier rated for 8 Ohm minimum safe operating load impedance 1 Refer to CHART A 8 Ohm Minimum Amplifier 2 In the first column find 8 Ohms 3 Follow the row to the right until you find 2 PAIR 4 Follow the column up to the very top row and find that the jumper2. days of receipt by You A Xantech Return Authorization RA must be obtained from Xantech by You your installer or your distributor for Product covered under this warranty Covered product must be sent to Xantech together with proof of purchase RA number prepaid and insured to Xantech Freight collect shipments will be refused Risk of loss or damage in transit is borne by the sender Xantech s warranty does not cover Products which have been received improperly packaged altered or physically damaged Products will be inspected upon receipt Except as may be expressly provided and authorized in writing by Xantech Xantech shall not be subject to any other obligations or liabilities whatsoever with respect to equipment manufactured or sold by Xantech or services rendered by Xantech THE FOREGOING WARRANTIES ARE EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESSED AND IMPLIED WARRANTIES INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ATTENTION TO OUR VALUED CONSUMERS To insure that consumers obtain quality pre sale and after sale support and service Xantech products are sold exclusively through authorized dealers and authorized distributors Xantech products are not sold online The warranties on Xantech products are NOT VALID if the products have been purchased from an unauthorized distributor or an online E tailer In order to determine if your Xantech re seller is authorized please call Xantech 8
3. setting should be set to x2 for both volume controls Installation Tip Setting the Volume 1 Set your receiver and or amplifier to the lowest possible volume setting 2 Turn all the volume controls to maximum volume up position for slider volume controls full clockwise position for rotary volume controls 3 Turn up the receiver and or amplifier volume setting until you reach the maximum listening level desired 4 Finally lower the volume control level Volume setting is now complete Changing the Face Plate 1 Gently press the tabs up on all four corners 2 Lift the face plate off the metal frame and remove 3 Replace with the correct color face plate Single Zone Single Speaker Pair Volume Control Application 1X SETTING Xantech PA series amplifier or equivalent D EN E ES mat e Jumper Settings Jumpers on Back E E kaw w pu HL Multiple Zone Single Speaker Pair Volume Control Application 4X SETTING Jumper Settings Jumpers on Back Xantech PA series amplifier or equivalent Single Zone Single Speaker Pair Volume Control and IR Receiver Application 1X SETTING Xantech PA series amplifier or equivalent b Right Speaker Left Speaker Note Applies to Model XVCD100IR XVCS100IR only CB18 Connecting Block not included The CB
4. 00 843 5465 Xantech Corporation 13100 Telfair Avenue 2 F Sylmar CA 91342 Installation Instructions Volume Controls 2006 Xantech Corporation Document 08905078A This document is copyright protected No part of this manual may be copied or reproduced in any form without prior written consent from Xantech Corporation Xantech Corporation shall not be liable for operational technical or editorial errors omissions made in this document
5. 18 provides a convenient way to parallel many wires onto a 4 conductor bus You can easily connect many home run leads from volume controls to the output terminals of a main amplifier The CB18 features the following Nine 4 terminal plug in connectors on a 4 conductor bus One in eight out or eight in one out capability Adhesive backed labels are included for attachment to the plug in terminals so that the speaker lead connections can easily be identified High current design allows amplifiers rated as high as 500 Watts to be used ocrew terminals handle wire sizes from 24 to 12 gauge Dimensions 11 74 x 1 44 x 1 4 Warranty Statement Xantech 5 Year Limited Warranty Effective for products sold after July 1 2006 Xantech Corporation Xantech warrants to the holder of a valid proof of purchase as the first end user purchaser You its products to be free from defects in materials and workmanship for the periods specified above from the date of purchase This limited warranty extends only to You for product purchased and used in the United States of America For product purchased outside of the United States of America the terms of this warranty apply EXCEPT that You must contact the Xantech authorized distributor in your region for warranty services Product is not intended for end user installation If within the applicable warranty period above You discover such item was not as warranted above and You promptly notify Xantec
6. INSTALLATION INSTRUCTIONS XANTECH VOLUME CONTROLS m XVCD50 XVCD100 XVCD1 oon XVCS50 XVCS100 a x XVCS100IR XVC50 XVC100 XVCO100 xantech Installation Instructions XVC Series Volume Controls Xantech s premier product line of XV volume controls are in wall mountable stereo speaker volume control with impedance matching capability From one to eight pairs or stereo speakers may be driven from one stereo power amplifier using an equal number of XV volume controls It maintains correct impedance matching between the amplifier and the speakers by the use of instant setting jumpers on the control This eliminates the need for separate impedance matching components in multi room installations Features and Benefits XVC50 XVD50 XVC50 Power handling 50 Watts continuous 150 Watts peak XVC100 XVD100 XVCS100 XVCO100 XVCD100IR XVCS100IR Power handling 100 Watts continuous 300 Watts peak All Models Adjustable impedance matching for up to 8 speaker pairs 1 2 4 8 pairs Attenuation 11 steps plus Off max 42 dB Frequency response 20Hz 20kHz 1 dB Speaker Terminals 16 gauge Quick Connect detachable Mounting Minimum 20 cu in J box or Mud Ring Note Be sure to check fit before choosing J boxes Isolated left and right channel grounds ensure safety with any bridged amplifier Fluid pop free switching during volume adjustments Compatible with 4 6 or 8 ohm speaker sys
7. h in writing Xantech shall repair or replace the items at its option Xantech may elect which remedy or combination of remedies to provide in its sole discretion Xantech may use functionally equivalent reconditioned refurbished pre owned or new products or parts under this limited warranty This warranty shall not apply a to product which shall have been installed by other than an authorized Xantech installer b to installed product which is not installed to Xantech s specifications c to product which shall have been repaired or altered by others than Xantech d to charges for installation or set up or adjustment of customer controls e to product that has suffered normal cosmetic deterioration f to product which shall have been subjected to negligence misuse abuse accident or damage by circumstances beyond Xantech s control including but not limited to lightning flood electrical surge tornado earthquake or any other catastrophic events beyond Xantech s control or g to product which shall have been subjected to improper operation connected equipment failure or malfunction inadequate packing or shipping damage maintenance or storage or to other than normal use of service The foregoing warranties do not cover reimbursement for labor transportation shipping removal installation or other expenses which may be incurred in connection with repair or replacement All claims for product shipping damage must be processes within 3
8. tems UL Listed to comply will all local building codes Installation requires only a screwdriver and wire strippers Installation Requirements You will need at the very least a 7s slotted screwdriver a slotted screwdriver wire cutters and wire strippers The recommended speaker wire to be used is 16 gauge stranded copper speaker wire For runs longer than 100 feet we recommend 14 gauge stranded copper speaker wire Never use solid core wire such as aluminum or Romex wire Most installations in the United States require a special fire rated wire CL 2 or CL 3 for speaker wire installed within a wall Consult your local building codes to find out what kind of wire is required Be sure to observe proper polarity when connecting a system The positive terminals should always be connected to the positive wire The negative terminals should always be connected to the negative wire Failure to do so will result in poor phasing and possible system malfunctions some areas allow the installation of the volume control to be placed in the same junction box as a high voltage connection 120VAC and divided by a low voltage partition This is not recommended as the speaker wires may pick up interference from the high voltage 120VAC power lines Again consult your local building codes to verify the proper way to install the product Impedance Jumper Settings for Identical Impedance How to use the impedance jumper setting chart
Download Pdf Manuals
Related Search