Xantech D5XH Switch User Manual
Contents
1. BROWN es OO ORANGE GREEN WHITE BLUE WHITE EXXXIXIIIIIIIII Shown tab down BROWN WHITE EXXXXXIXXXIIXIXIXE ORANGE WHITE Figure 3 3 T 568A Wiring Standard 08905154B 14 D5KP Rear SYSTEM PORT ANGE WHITI D5KP Rear D5KP Rear NC Q lt x 5 as LOCAL PORT ENX sess ss Cat 5 Sisisissis D5KP Rear D5KP Rear Figure 3 4 ZONE OUT Connections Note For wire runs up to 150 the Cat 5 connections are all that is necessary For wire runs over 150 use the AUX POWER OUT connectors as described in the section entitled Auxiliary Power Connector AUX POWER OUT 08905154B 15 D5KP Speaker Connections The D5XH sends a digital audio signal to connected D5KP Keypads where it is amplified and sent to speakers WARNING The D5KP s amplifier is capable of powering a single pair of 8 6 Ohm speakers DO NOT connect speakers with a rating of less than 6 Ohms DO NOT connect more than one speaker to either speaker connector of the D5KP In doing this damage to the D5KP may occur and will void the products warranty To connect speakers to D5KP Keypads 1 Ensure that system power is OFF 2 Remove the SPEAKER CONNECTOR from the D5KP 3 Strip speaker wire back 1 4 4 Loosen speaker terminal screws on the speaker connectors 5 Insert soeaker wires into terminals making sure to maintain polarity 6 Tighten screws on speaker term2. D5IP Front Audio Source Digital Coaxial Output Digital Coaxial Cable COAX OPTICAL IN IN IR OUT A RCA COAX IH Figure 3 9 Local Source to D5IP Connections Digital Coaxial NOTE Be sure the RCA OPT COAX switch is down and set to COAX 08905154B 19 D5IP uon near Side View SYSTEM PORT ANGE WHITI zem hcm mz e 5 zm cece L L R R e R Figure 3 10 D5IP to D5KP Connections 08905154B 20 IR OUT Connect a standard IR Emitter 283D emitter for example from the IR OUT port on the front of the D5IP to the IR receiver on the front of the audio source see Figure 3 14 For sources that have an IR Input port on the back of the unit use a 3 5mm to 3 5mm mono interconnect cable Xantech P N 06017400 1 Foot Mono Cable instead see Figure 3 12 D5IP Front D5IP Front 9 di d 9 id Audio IR input i ria 3 5mm Mono Interconnect Cable Figure 3 11 IR OUT to Local Source IR Emitter Figure 3 12 IR OUT to Audio Source 3 5mm Interconnect Cable 08905154B 21 Adding Zones to a D5RH Digital Audio Router A basic D5RH system can contain a maximum of four sources and four zones By adding D5XH Digital Audio Routers the system can contain a maximum of twenty eight zones Each D5XH expands the system by up to six zones while still maintaining a four source maximum limit This section details co
3. ge l j y JNPA RED Ae EE 77 EE tn ama i UNT 2 et UN see BEBEBB USB IN ZI z2 z3 Ialz az zsiza DEI ZONE PAIRING JN D Figure 3 17 Expanded System Overview 08905154B 25 Connections between a D5XH chassis in a Stand Alone configuration and D5XH Digital Audio Routers involve Cat 5 patch cables routed between the units All cables are included with the D5XH Connections are required for e EXPANSION OUT EXPANSION IN e SOURCE LOOP OUT SOURCE LOOP IN EXPANSION OUT EXPANSION IN simply connect a Cat 5 patch cable from the D5XH s EXPANSION OUT port to the first D5XH s EXPANSION IN port For multiple D5XH units connect a Cat 5 patch cable from the first D5XH s EXPANSION OUT port to the next D5XH s EXPANSION IN port and so on See Figure 3 18 for details SOURCE LOOP OUT SOURCE LOOP IN Connect a Cat 5 patch cable from each SOURCE LOOP OUT of the D5XH to each corresponding SOURCE LOOP IN on the next D5XH and so on See Figure 3 18 for details I D5IP Source Wall Plate X4 LLL IN x Es DOP IJ xr n LOOP 5 EXPANSION UL D5XH To at 5 C i e D Y Ea LOOP Y n LL lp To Additional D5XH Chassis Figure 3 18 System Expansion Connections 08905154B 26 D5XH ZONE OUT Additional zones beyond the six that connect to the D5XH are connected directly to their corresponding D5XH s ZONE OUT ports using Cat 5 See Figure 3 19 for detai
4. i 7 i i i li rgi Bae L L i L N O Oooo poh met 5E r3 X a e SSS at at at it eo om E D5XH Unit 1 O 0000 EM D5XH Unit 2 EE D5XH Unit 3 EM D5XH Unit 4 Figure 2 7 Expanded System 4 Sources 24 Zones Local Sources 08905154B 12 3 Connections The D5XH is part of an integrated system that requires the use of other components Depending on the system design these components may include D5KP Amplified Keypad at least one per zone required D5IP Source Input Wall Plates one per zone where a Local Source is desired D5RH Hub Main 4x4 Digital Distribution System Hub Xantech Outdoor Ceiling and In Wall Speakers Xantech IR Emitters and accessories This section describes the connectivity between these various components and the source audio components that comprise the system Each D5RH D5XH system is unique and not all connections will be made in every installation Important Safety Note Make sure that the D5XH is powered OFF before making any connections Q Loop Inputs SOURCE LOOP IN The Source Loop Inputs are used primarily when adding D5XH Routers to a D5RH in order to create more than four zones These connectors carry Audio and IR information between the units and allow seamless functionality in all areas of the home with no complicated cross wiring splicing or specialized adapters needed When adding a D5XH Router to a DRH syst
5. Figure 2 2 T 568A Wiring Standard Keypads to Speakers Run 16AWG 2 conductor stranded copper speaker wire between keypad locations and speaker locations 08905154B 9 Local Sources to Keypads Local sources are only available within the area that they are installed They will not be available to other areas of the house as they are not distributed by the DBRH D5XH Run lengths of Cat 5 from any local in room source to the keypad located in that area Expanded 4 Source 8 28 Zone System D5XH Expansion Router Figure 2 5 shows an expanded system with four sources and ten zones with the addition of Local sources in four of the zones Each zone can have one local source The system is comprised of a D5RH Digital Audio Router D5XH Expansion Router D5KP Amplified Keypad Controllers D5lP Local Source Wall Plates and Xantech XTC Series Speakers This configuration provides audio from each source into each zone as well as control of each source from each zone Zones with Local sources have access to and control of those sources but the Local Sources are not available to other zones within the system This system can be expanded up to 28 zones using additional D5XH s i sl i i i i 3 ooo0o0 i l i Ir ir SAP Li ie m m m m Figure 2 5 Expanded System 4 Sources 10 Zones Local Sources 08905154B 10 S
6. 6 Zone Digital Audio Expansion Router when used with the D5RH Digital Audio Router provides the ability to listen to 4 different audio sources in up to 28 separate areas of the home for total flexibility and convenience No need to have multiple audio systems in different areas just select a source from one of Xantech s premium in wall keypad sit back and enjoy Crystal Clear Digital Sound End to end digital architecture means that the entire signal path of the audio system remains in the digital domain from start to finish This means that noise signal loss and other unwanted effects are never present Each keypad contains a 30 Watt digital amplifier that allows the user to play music at loud volume when desired This also means that music at any volume is full and rich without distortion and with plenty of bass Simple Logical Installation The D5RH and D5XH connect with CAT 5 and speaker wire making them reliable and easy to install Any digital or analog audio source can be connected directly to the D5XH Digital Audio Router or remotely using a D5IP Local Source Wall Plate Keypads and Wall Plates are connected to the D5XH using CAT 5 wiring inexpensive and reliable while speakers are connected to D5KP Amplified Keypads using traditional speaker wire Entertaining Possibilities The D5XH s Whole House Music and Zone Grouping features make entertaining more fun than ever Fully customized audio options allow for control of the entir
7. Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help CAUTION Changes or modifications not expressly approved by Xantech could void the user s authority to operate the equipment Caring For the D5XH Clean only with a dry soft cloth It is important to properly care for your D5XH DDS Hub Follow these guidelines to ensure your device is preserved and protected e Do not expose the D5XH to rain liquids or moisture for an extended period of time e Do not expose the D5XH to temperature extremes e Do not place any objects on top of the D5XH to prevent chassis damage Operating Temperatures amp Environments Operating Temperature 32 104 F 0 40 C Humidity 0 9096 Precautions e Always exercise care when operating the D5XH Digital Audio Distribution Hub e Do not install near any heat sources such as radiators heat registers stoves or other apparatus including amplifiers that produce heat e Inthe unlikely event that smoke abnormal noise or strange odor is present immediately power the D5XH off Please report the problem to your dealer immediately e Never attempt to disassemble the D5XH You will lose any product warranty on the unit 08905154B Eey 1 Introduction Modern Convenience The D5XH 4 Source
8. additional D5XHs Sources Audio IR mudo IR Audio Audio Cables Emitter Cables Emitter Cables ei Cables Zones x 6 Local Source Ls Li LI ALL 1 Per Zone Audio Cables Ente Cat 5 Cat 5 D5XH Coe ee rile lao We le be I Figure 3 16 D5XH Stand Alone Connections 08905154B 24 Adding Zones with additional D5XH Digital Audio Routers A basic Stand Alone No D5RH D5XH system can contain a maximum of four sources and six zones By connecting additional D5XH Digital Audio Expansion Routers the system can contain a maximum of twenty four zones Each D5XH expands the system by up to six zones while still maintaining a four source maximum limit This section details connections required for adding D5XH Digital Audio Routers to a D5XH Stand Alone System it of Chassis Max of Zones 1 D5XH 6 1 D5XH 1 D5XH 1 D5XH 2 D5XH 1 D5XH 3 D5XH 24 Sources muB oe a ax Audio Cables Zones x 6 Local Source 1 Per Zone Audio IR Audio IR Cables Emitter Cables Emitter IR Emitter Audio IR Cables Emitter Audio Cables Zones x 6 Local Source 1 Per Zone Cat 5 TXPANSION Zones x 6 Local Source 1 Per Zone tf fi SCURCE Loar oJ 7 77 vaya bp Me AIRED N AIRED Iz EsE4ESLE ZONE PAIRING t 4 Local Source ff goce our Lopes d rz ABDRME MN 1 Per Zone Y iy
9. to determine that the audio product is in proper operating condition Lightning Storms Unplug this apparatus during lightning storms or when unused for long periods of time Attachments and Accessories Use only attachments accessories specified by the manufacturer Cart Stand Tripod Bracket or Table Use only with a cart stand tripod bracket or table specified by the manufacturer or sold with the apparatus When a cart is used use caution when moving the cart apparatus combination to avoid injury from tip over Disconnect Device Where the mains plug or an appliance coupler is used as the disconnect device the disconnect device shall remain operable NOTE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not in stalled and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e
10. to group all low voltage video speaker wires Cat 5 telephone etc wires wherever possible It is a good practice to label both ends of all cables and to protect wires by tying a plastic bag over the ends Note Do not run low voltage wires closer than 12 from high voltage wires If necessary cross low voltage wires at a 90 angle to prevent interference Retro Fit Wiring Post Construction Retro fit installations are more difficult to complete than pre construction because walls and ceilings are intact Typically wires must be fished into position through walls floors and ceilings Holes must be cut speakers mounted directly in the ceiling or walls with no rough in brackets and Keypads and local source wall plates must be mounted in existing drywall Pre Wiring D5XH to D5KP Keypads The D5XH and all associated components are wired using Cat 5 terminated to the T 568A Wiring otandard Figure 2 2 When pre wiring run lengths of Cat 5 from the pre determined equipment location the head end to each Keypad location The Cat 5 routes all audio power IR and status information needed for full system operation Note For maximum performance over long runs more than 150 ft run an additional 16AWG 2 conductor wire for external power 12 34 56 78 o e LI ZA LJ EM o mI ry _ hdi LJ xal LJ lars BLUE WHITE ORANGE Shown tab down GREEN WHITE EX ORANGE WHITE BROWN WHITE
11. 1 2 and Table 1 1 provide descriptions and locations of Front Panel controls and indicators Figure 1 1 D5XH Front Panel Indicator Button Function 1 LED Power LED Indicates Power ON OFF Status Red Power Button Turns System Power ON OFF Table 1 1 Front Panel 08905154B NUR Rear Panel The Rear Panel of the D5XH has connections for Power Source Loop Inputs from D5RH Source Loop Outputs to additional D5XH chassis Zone Outputs IR Outputs Auxiliary Power USB and Expansion capabilities as well as Zone Pairing and Unit I D DIP Switches Figure 1 3 and Table 1 2 provide descriptions and locations of Rear Panel connections 11 10 9 8 7 Figure 1 3 Rear Panel Connector source Loop Input Source Audio Inputs from D5RH oource Audio Outputs to D5XH SUC Soap Output Expansion Chassis Unit I D DIP Switches Sets Chassis Unit Identification Aux Power Out Zones 1 3 Provides Additional Power to Keypads Aux Power Out Zones 4 6 Provides Additional Power to Keypads Plugs into 110 VAC Wall Outlet Export AC Power Connector 240VAC models also available Zone Output Ports Connect to D5KP Amplified Keypads Located in Each Zone USB Port For Firmware Updates 9 Zone Pairing Switches Links Multiple Zones Together Control Status Link Between D5RH Expansion Pone and Additional D5XH Chassis RS232 Port RS232 Communication Port Table 1 2 Rear Panel 08905154B fe 2 System Design Overview A
12. NPUT of the D5RH A run of Cat 5 terminated to T 568A standard see Figure 3 3 page 12 is required between the D5KP Amplified Keypads and the location designated for the D5lP Connections between a source component and the D5IP are detailed in Figure 3 7 Figure 3 8 and Figure 3 9 while connections between the D5IP and the D5KP Amplified Keypads are detailed in Figure 3 10 D5IP Front Stereo RCA Patch Cables Audio Source Analog Output ACA il COAX Figure 3 7 Local Source to D5IP Connections Analog NOTE Be sure the RCA OPT COAX switch is up and set to RCA 08905154B 18 D5IP Front Audio Source Digital Digital Optical Optical Output DIGITAL Figure 3 8 Local Source to D5IP Connections Digital Optical NOTE Be sure the RCA OPT COAX switch is middle and set to OPT NOTE Multi channel digital audio formats 5 1 7 1 etc are not supported by the D5IP D5RH or D5XH However many audio video sources allow you to change the digital output to PCM Stereo In most cases this will allow multi channel audio sources to output a summed stereo signal through the digital output Consult the audio video source manual for details NOTE Some audio sources which utilize a digital output require that you enable the digital output before it will function If there is no audio present check the setup menu of the audio source to confirm that the digital output is enabled
13. Range Compression DRC Local In Room Source Connectivity with Optional D5IP Local Source Wall Plates Supports all Features of D5RH Digital Audio Router Paging DB Functionality w Optional Communications Controller Compact Single Rack Space Design Rack Mountable Optional Rack Ear Kit Available RM1UKIT D5XH Accessories D5RH 4 Source 4 Zone Digital Audio Hub D5KP Amplified Keypad Controller D5IP Source Input Wall Plate D5MR Slim line IR Remote D5LR Learning Remote Control RM1UKIT 1U Rack Ear Kit 08905154B JD a Defining Terms Zone A Zone is defined as an area of the house that has separate source selection capabilities from all other areas of the house Typically a zone is comprised of a single room but it is possible for a zone to spread across multiple rooms kitchen dining room master bedroom master bath or for multiple zones to be contained in one room game room bar area or multiple zones in the yard Source A Source is any audio or audio video device that is connected to the SOURCE INPUTS of the D5RH Any Source can be heard in any zone in the system Local Source A Local Source is an audio or audio video device that is connected to a D5IP Source Input Wall Plate Local Sources are able to be heard only in the zone in which they are installed and may not be heard in other zones of the system Front Panel The front panel of the D5XH is populated simply by a Power LED and a power button Figure
14. authorized dealers and authorized distributors The warranties on Xantech products are NOT VALID if the products have been purchased from an unauthorized dealer or distributor In order to determine if your Xantech re seller is authorized please call Xantech 800 843 5465 XANTECH PRODUCT WARRANTY DURATION go to Xantech com warranty for model numbers Hand Held Remote Controls 1 year Limited SPLCD Product 1 year Limited Source Components XIS100 1 year Limited Control Interfaces 2 year Limited 08905154B 31 Xantech Corporation 13100 Telfair Ave 2F Sylmar CA 91342 Xantech com Installation Instructions D5XH 2008 Xantech Corporation Document 08905154B This document is copyright protected No part of this manual may be copied or reproduced in any form without prior written consent from Xantech Corporation Xantech Corporation shall not be liable for operational technical or editorial errors omissions made in this document 08905154B 32
15. aying close attention to polarity 10 Tighten the screws on the D5KP s PWR IN terminal 11 Connect the terminal strip back onto the AUX POWER OUT connector on the D5XH Re LUE DIES CU irem DSKP Rear AUX POWER OUT AUX POWER OUT ZONE 3 ZONE 4 6 Z s 4 7 73 74 D5XH Figure 3 6 AUX POWER OUT ZONES 1 3 4 6 Connections 2 08905154B 17 O Port USB IN The USB IN port is designed to allow upgrades to the D5XH s firmware OQ Power Connector Connect the supplied cord from the AC Power Connector into a properly grounded electrical outlet System Expansion The D5XH is capable of supporting up to four sources to up to six zones The system may be expanded in two ways e Local Sources e Adding Zones Additional D5XH chassis Local Sources Each zone of a DBRH D5XH based system can have its own Local source connected directly to the zone s D5KP Amplified Keypads using a D5IP Source Input Wall Plate A source connected to a D5KP is accessible from the zone in which it is connected It is NOT AVAILABLE to the other zones of the system Both audio and IR control capabilities are available to Local Sources through the D5KP A zone may have a maximum of one Local Source D5IP Source Input Wall Plate A D5IP Source Input Wall Plate is required to add a Local Source to a zone The wall plate has audio and IR connections similar to the SOURCE I
16. c Range Compression DRC Loudness Power Zone ON OFF All OFF System OFF 08905154B 28 source control functionality is performed by IR Remote Control through the D5KP s built in IR Heceiver or an additional IR receiver connected to the Local IR Receiver Input on the back of the D5KP Complete instructions for installing and operating the Keypads are available in the D5KP Amplified Keypads Controller Installation Manual fo WHM OND iPod Figure 4 3 D5KP Amplified Keypads Appendix A Specifications Power Input 120 VAC 3 Amps Export 240VAC models also available Sampling Frequency 48kHz Digital Audio Resolution 24 Bit Signal to Noise Ratio 94dB Frequency Response 20Hz 20kHz 0 1dB H x W x D w feet 2 3 8 x 17 x 14 1 8 8 6cm x 43 2cm x 35 9cm H x W x D w o feet 1 3 4 x 17 x 14 1 8 4 4cm x 43 2cm x 35 9cm Weight 19lbs 8 6kg Unit Weight 21lbs 9 5kg Shipping Weight 08905154B 20 5 Troubleshooting Table 5 1 provides troubleshooting information for the D5XH Digital Audio Router Audio Possible Cause No audio present in a specific 1 Source not playing Press Play turn ON etc zone 2 Zone not ON Press Power on the D5KP 3 Zone volume turned all the Increase volume way down 4 Speakers in room miswired or a Test known good speaker at defective or DBKP miswired D5KP speaker connector b Verify connections No audio from specific source Digital audio ou
17. d outside of the United States of America You must contact the Xantech authorized distributor in your region for warranty services Product is not intended for end user installation If within the applicable warranty period above You discover such item was not as warranted above and You promptly notify Xantech in writing Xantech shall repair or replace the items at its option Xantech may elect which remedy or combination of remedies to provide in its sole discretion Xantech may use functionally equivalent reconditioned refurbished pre owned or new products or parts under this limited warranty This warranty shall not apply a to product which shall have been installed by other than an authorized Xantech installer b to installed product which is not installed to Xantech s specifications c to product which shall have been repaired or altered by others than Xantech d to charges for installation or set up or adjustment of customer controls e to product that has suffered normal cosmetic deterioration f to product which shall have been subjected to negligence misuse abuse accident or damage by circumstances beyond Xantech s control including but not limited to lightning flood electrical surge tornado earthquake or any other catastrophic events beyond Xantech s control or g to product which shall have been subjected to improper operation connected equipment failure or malfunction inadequate packing or shipping damage maintenance or st
18. e house from one location and also allow for the creation of multiple zone linking where groups of zones work together Control for Parents The Source Lock Out feature allows you to disable specific sources in the kid s rooms that you don t want them to access About DIGI 5 Technology DIGI 5 is a revolutionary new technology standard that provides a complete end to end digital audio solution over CAT 5 wiring DIGI 5 is based on advanced digital distribution and amplification circuits that allow multi room audio systems to be installed quickly and cost effectively DIGI 5 is a collaboratively developed technology that is licensed by the Linear Home Technology Group and is being initially integrated on a Linear group wide basis targeted to expand market and consumer acceptance of such systems 08905154B 4 Features 4 Source 6 Zone Expansion for D5RH Digital Audio Router Combine Up to 4 D5XH Chassis for Total of Up to 28 Zones otand Alone 4 Source 6 Zone Capability Expandable to 24 Zones End to End Digital Architecture For Crystal Clear Sound with No Signal Loss Simple Cat 5 Wiring requirements Innovative D5KP Amplified Keypad Controllers not included Provide Custom Control Options No PC Software Required for Setup Simply Plug in DBKP Keypads and Go D5RM Slim line IR Remote Included Whole House Music Turns On All Zones to the Same Source Zone Functions Do Not Disturb Source Lock Out Tone Control Balance Loudness Dynamic
19. em simply connect Cat 5 Patch Cables included with the D5XH from the SOURCE LOOP OUTs of the D5RH to the SOURCE LOOP INs of the D5XH as shown in Figure 3 1 Complete connections for expanded systems are described in the section entitled Multi Chassis Connections D5RH CIN SOURCE LOOP OUT 3 Cat 5 Ethernet Patch Cables D5XH Figure 3 1 Source Loop Inputs 08905154B Lm D EXPANSION IN Connect the Cat 5 Patch Cable included with the D5XH from the DBRH s EXPANSION OUT port to the D5XH s EXPANSION IN port as shown Complete connections for expanded systems are described in the section entitled Multi Chassis Connections D5XH D5RH IN SOURCE LOOP OUT exeansion CM 5 Cat 5 Ethernet Patch Cable EXPANSION EXPANSION p 4 EXPANSION J OUT OUT Figure 3 2 mee In Q ZONE OUT The ZONE OUT RJ 45 connectors interface with D5KP Amplified Keypad Controllers through Cat 5 cables wired to the T 568A Standard These connectors carry IR information from the Keypads as well as audio information to the Keypads Status information is also carried between the D5RH D5XH chassis and the Keypads While a great deal of information is handled by the ZONE OUT connections the connections are straightforward Simply connect Cat 5 cables terminated to the T 568A configuration Figure 3 3 from each Keypad to the corresponding ZONE OUT connector as shown in Figure 3 4 aa 34 56
20. he first D5XH to each corresponding SOURCE LOOP IN on the next D5XH and so on See Figure 3 14 for details D5RH CI SOURCE LOOP OUT y 3 n ee tp LO EXPANSIO A OUT IN SOURCE L OP URCE LOOP OUT EXPANSION 1 3 T E d X A men LOOP t m EXPAINSION EXPANSION J UT To Additional D5XH Chassis Figure 3 14 System Expansion Connections 08905154B 23 D5XH ZONE OUT Additional zones beyond the four that connect to the D5RH are connected directly to their corresponding D5XH s ZONE OUT ports using Cat 5 See Figure 3 15 for details D5KP Rear D5XH Figure 3 15 D5XH ZONE OUT Connections Stand Alone No D5RH 4 Source 6 Zone System Figure 3 16 shows a D5XH stand alone system with four sources and six zones with the addition of a local source in Zone 6 Each zone can have one local source The system is comprised of a D5XH D5KP Amplified Keypads Controllers D5IP Source Input Wall Plates and Xantech XTC Series opeakers This configuration provides audio from each source into each zone as well as control of each source from each zone Zones with Local Sources have access to and control of those sources but the Local Sources are not available to other zones within the system This system can be expanded up to 24 zones using
21. inals 7 Re connect the terminal strip to the SPEAKER CONNECTOR on the D5KP 8 Connect speaker wires to the room speakers maintaining correct polarity D5KP Rear Speaker AUX Power Connector Connector L L R R SPEAKERS n 1 4 16AWG Speaker Wire To Speakers Figure 3 5 Speaker Connections 08905154B 16 O Power Connector AUX POWER OUT For wire runs over 150 it is recommended to run an additional 16 AWG 2 conductor wire from the head end location to the Keypads locations This will allow the AUX POWER OUT terminals to supply additional power to the Keypads to compensate for the additional distance For wire runs over 300 16 AWG 2 conductor wire is required The maximum wire run using Cat 5 and 16 AWG 2 conductor is 600 Make all connections between the D5XH and the D5KP Amplified Keypads as previously described then make the aux power connections described below To make connections Ensure that system power is OFF otrip the ends of the 16 AWG wire 1 4 on both ends of the wire run Remove the terminal strip from the AUX POWER OUT connector on the D5XH Loosen the screws for the appropriate zone s terminal pairs on the terminal strip Insert the wires into the terminal strip paying close attention to polarity Tighten the screws on the terminal strip Remove the terminal strip from the PWR IN connector of the D5KP Loosen the screws on the D5KP s PWR IN terminal Insert the wires into the terminal p
22. ith them may be fatal Object and Liquid Entry Never insert objects of any kind through the openings of these appliances as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock Care should be taken so that objects do not fall and liquids are not spilled into the appliance through openings in the enclosure Servicing Do not attempt to service these appliances yourself as opening or removing covers may expose you to dangerous voltage or other hazards Refer all servicing to qualified service personnel 08905154B 2 Damage Requiring Service These appliances should be serviced by qualified service personnel when A power supply connection or a plug has been damaged or e f liquid has been spilled into the appliance or objects have fallen into the appliance or The appliance has been exposed to water or moisture or The appliance does not appear to operate normally or exhibits a marked change in performance or The appliance has been dropped or the enclosure damaged Replacement Parts When replacement parts are required be sure the service technician has used replacement parts specified by the manufacturer or that have the same characteristics as the original part Unauthorized substitutions may result in fire electric shock or other hazards Safety Check Upon completion of any service or repairs to this audio product ask the service technician to perform safety checks
23. ls D5KP Rear sss IB CAL PCT rar it gba D5XH Figure 3 19 D5XH ZONE OUT Connections 4 Settings amp Operation DIP Switch Settings There are two groups of DIP switches on the rear panel of the D5XH that must be set prior to operation e UNIT ID e KEYPAD PAIRING UNIT ID Each D5XH chassis has a corresponding DIP switch setting relative to the other chassis To set UNIT ID DIP switches 1 Correctly identify which chassis controls the associated zones 2 Assign a unique unit ID based on the silkscreen on the rear panel 3 Repeat this process for the each other expansion chassis 08905154B 27 UNIT ID Figure 4 1 UNIT ID DIP Switches KEYPAD PAIRING The KEYPAD PAIRING DIP switches allow each of the zones to be paired or grouped with any other zone Any zone that is in the UP position will be paired with any other zone that is also placed in the UP position This feature is useful to create large party zones where combined areas of the house share audio and system control PAIRED UNPAIRED z1 z2 z3 z4 z5 zo ZONE PAIRING Figure 4 2 ZONE PAIRING DIP Switches Operation Once the D5RH D5XH is connected all functionality is controlled by the D5KP Amplified Keypads that are installed in each zone Essentially a D5KP controls source Selection Volume Mute Whole House Music WHM Do Not Disturb DND Source Lock Out EQ Bass amp Treble Balance Left Right Dynami
24. nnections required for adding D5XH Digital Audio Routers to a D5RH 2 Zone X4 Local Source amp 1 Per Zone Sources X 4 ME iE LL 2m Audio Calbes IE Oooo JT EN ir Cat 5 m l Local Source 1 1 Per Zone EI EIS L gt Cat 5 F P Audio IR Emitters 1 Calbes Cat 5 6 0 0 0 FEPTEM 00 00 FFT Tooo e PPP 0 ELI FEPPPPEPEERM 1 Zone X6 DRM 3 cr ot LT e ne _ z cE Local Source 1 Per Zone b D5XH L Zone X 6 il Local Source 1 Per Zone o EE j B i D5XH B m Cat 5 f B Local Source 1 Per Zone D5XH 1 D E d VES m Cat 5 D5XH s Figure 3 13 Expanded System Overview 08905154B 22 Connections between a D5RH chassis and D5XH Digital Audio Routers involve Cat 5 patch cables routed between the units All cables are included with the D5XH Connections are required for e EXPANSION OUT EXPANSION IN e SOURCE LOOP OUT SOURCE LOOP IN EXPANSION OUT EXPANSION IN simply connect a Cat 5 patch cable from the DBRH s EXPANSION OUT port to the first DDXH s EXPANSION IN port For multiple D5XH units connect a Cat 5 patch cable from the first D5XH s EXPANSION OUT port to the next D5XH s EXPANSION IN port and so on See Figure 3 14 for details SOURCE LOOP OUT SOURCE LOOP IN Connect a Cat 5 patch cable from each SOURCE LOOP OUT of the D5RH to each corresponding SOURCE LOOP IN on the first D5XH For multiple D5XH units connect a Cat 5 patch cable from each SOURCE LOOP OUT of t
25. nstaller Ventilation The appliances should be situated so that their location or position does not interfere with their proper ventilation These appliances should never be placed near or over a radiator or heat register These appliances should not be placed in a built in installation such as a bookcase or cabinet that may impede the flow of air through the ventilation openings Non Use Periods Appliances that are left unattended and unused for long periods of time should be de energized Grounding or Polarization Do not defeat the safety purpose of the polarized or grounding type plug A polarized plug has two blades with one blade wider than the other blade A grounding type plug has two blades and a third grounding prong The polarized wide blade and the third prong are provided for your safety If the provided plug does not fit your outlet consult an electrician for replacement of the obsolete outlet Power Cord Protection Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles and the point where they exit from the apparatus Water Do not use the apparatus near water Cleaning Unplug the apparatus from the power outlet before cleaning Use only a dry cloth to clean the apparatus Power Lines An outdoor antenna should be located away from power lines When installing an outside antenna system extreme care should be taken to avoid touching power lines or circuits as contact w
26. orage or to other than normal use of service The foregoing warranties do not cover reimbursement for labor transportation shipping removal installation or other expenses which may be incurred in connection with repair or replacement All claims for product shipping damage must be processes within 3 days of receipt by You A Xantech Return Authorization RA must be obtained from Xantech by You your installer or your distributor for Product covered under this warranty Covered product must be sent to Xantech together with proof of purchase RA number prepaid and insured to Xantech Freight collect shipments will be refused Risk of loss or damage in transit is borne by the sender Xantech s warranty does not cover Products which have been received improperly packaged altered or physically damaged Products will be inspected upon receipt Except as may be expressly provided and authorized in writing by Xantech Xantech shall not be subject to any other obligations or liabilities whatsoever with respect to equipment manufactured or sold by Xantech or services rendered by Xantech THE FOREGOING WARRANTIES ARE EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESSED AND IMPLIED WARRANTIES INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ATTENTION TO OUR VALUED CONSUMERS To insure that consumers obtain quality pre sale and after sale support and service Xantech products are sold exclusively through
27. pplications Planning Before installing the D5XH it is essential to have a detailed and accurate system design The first step to a good design is to map the system It is advisable to mark up a copy of the house floor plan with speaker keypad and equipment locations etc Make sure that all locations are decided upon before pre wiring so that all necessary wiring and installation hardware is in place It is essential that ALL system components are accounted for prior to the pre wire stage After establishing design goals make a detailed list of all components Include source equipment Keypads expansion Routers local source wall plates IR emitters etc L L i i i i D D r D OD E dp o E do db H U e 89 89 59 ON m i D D EGJ m 9 om i L ILI NN jJ Sai 4 CIC IL os L Figure 2 1 System Wiring Overview Note For clarity Figure 2 1 shows a single zone connected to a D5RH and a single zone connected to a D5XH Expansion Router 08905154B 8 Pre Construction In a pre construction installation walls and ceilings are open with no drywall installed This is desirable and allows the installer greater access than in retro fit applications Before actually running any wire or cable take the time to look around each room or area of the house and plan your wire paths for maximum efficiency Look for routes through uncluttered parts of the stud wall or ceiling that allow you
28. tand Alone No D5RH 4 Source 6 Zone System Figure 2 6 shows a stand alone system with four sources and six zones with the addition of Local sources in two of the zones Each zone can have one local source The system is comprised of a D5XH D5KP Amplified Keypad Controllers D5IP Source Input Wall Plates and Xantech XTC Series opeakers This configuration provides audio from each source into each zone as well as control of each source from each zone Zones with Local Sources have access to and control of those sources but the Local Sources are not available to other zones within the system This system can be expanded up to 24 zones using additional D5XHs 4 units in all hanh e F3 F3 F3 F3 cm i i i j T A Ei z O oooo Su a 9 CLT IE om Figure2 6 Stand Alone 4 Source 6 Zone 08905154B E Expanded Standalone No D5RH 4 Source 6 24 Zone System Figure 2 7 shows a stand alone system with four sources and twenty four zones with the addition of Local Sources in eight of the zones Each zone can have one local source The system is comprised of four D5XH D5KP Amplified Keypad Controllers D5IP Source Input Wall Plates and Xantech XTC series Speakers This configuration provides audio from each source into each zone as well as control of each source from each zone Zones with Local Sources have access to and control of those sources but the Local Sources are not available to other zones within the system
29. tput not enabled Check setup menu and confirm digital audio output is enabled Multi channel digital audio Change digital Output to PCM formats 5 1 7 1 etc are not otereo supported by the D5IP D5RH etc Incorrect audio format selection Check RCA OPT COAX selection switch for proper selection Perform steps above 2 Digital source is outputting oelect PCM Stereo output on multi channel audio format 5 1 source component Consult 7 1 etc source s manual for details 3 Digital output not enabled on Enable digital output through BEEN source source s menu Set to PCM for details Hum or buzz through system 1 Ground loop Ensure proper grounding using outlet high Poor Audio quality 1 Clipping or distortion Adjust GAIN settings stereo Consult source s manual 2 Speaker out of phase Carefully check polarity of each speaker 3 Incorrect assignment of Isolate to source or room and left right source RCA cables or correct speaker cables 08905154B 30 Xantech Limited Warranty Effective for products sold after July 1 2006 Xantech Corporation Xantech warrants to the holder of a valid proof of purchase as the first end user purchaser You its products to be free from defects in materials and workmanship for the periods specified below from the date of purchase This limited warranty extends only to You for product purchased and used in the United States of America For product purchase
30. xantech INSTALLATION INSTRUCTIONS D5XH DIGI 5 DDS Digital Distribution System Rack Mount 6 Zone Expansion Hub 08905154B m Safety Information WARNING 4 RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instruction in the literature accompanying the appliance WARNING TO REDUCE THE RISK OF FIRE OR SHOCK DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE IMPORTANT SAFETY INFORMATION Read Information All the safety and operating information should be read before the appliance is operated Follow Information All operating and use information should be followed Retain Information The safety and operating information should be retained for future reference Heed Warnings All warnings on the appliance and in the operating instructions should be heeded Wall Mounting Mounting of this appliance should be done only by an authorized i
Download Pdf Manuals
Related Search