VTech 9119 Cordless Telephone User Manual
Contents
1. 3 GETTTING STARTED Setting Up Your VT9119 Ab ELED Ta AME 1 Choose an area near an electrical outlet and a telephone wall jack 2 Plug the AC power adapter into an electrical outlet and the DC connector to the back of the base unit CAUTION Use only the AC adapter shipped with your VT9119 It is specifically designed for this product NOTE Connect power to the base unit before placing the handset in the cradle 3 CHARGETHE HANDSET BATTERY PACK BEFORE USE The batteries recharge automatically whenever the handset is in the base unit cradle The batteries must be charged for 16 hours before using your phone for the first time 4 Connect the telephone line cord Insert one end of the telephone line cord into the jack at the rear of the base unit Plug the other end into a telephone wall jack Make sure the plugs snap securely into place 5 CHECK FOR A DIAL TONE After the batteries are charged pick up the handset and press the PHONE key The IN USE indicator should light up and you should hear a dial tone If not see IN CASE OF DIFFICULTY CAUTION 1 Never install telephone wiring during a lightning storm 2 Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations 3 Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface 4 Use caution when installing or modifying tele2. RICHMOND BC V6X 129 12 FCC AND IC REGULATIONS This equipment complies with FCC AND IC REGULATIONS 15 and 68 of the Federal Communications Commission FCC rules for the United States It also complies with regulations RSS 210 and CS 03 of Industry Canada IC A label is located on the underside of the base unit containing either the FCC registration number and Ringer Equivalence Number REN or the IC registration number and Load Number You must upon request provide this information to your local telephone company This equipment is compatible with inductively coupled hearing aids FCC Part 15 Warning Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment The equipment has been tested and found to comply with part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try and correct the in
3. originally provided with the product We recommend using the original carton and packing materials e Include in the package a copy of the sales receipt or other evidence of date of original purchase if the unit was purchased within the last twelve months e Print your name and address along with a description of the defect and include this in the package e Include payment for any service or repair not covered by the warranty as determined by VTECH Communications e Inthe US ship the unit via UPS Insured or equivalent to San Antonio Returns Center 1145 Coliseum Road Department Vtech San Antonio TX 78219 VTECH Communications assumes no responsibility for units sent without prior Return Authorization WHAT DOES OUR WARRANTY NOT COVER e Batteries Damage from misuse neglect or acts of nature lightning floods power surges etc e Products which may have been modified or incorporated into other products e Products purchased outside the USA e Products serviced by the owner or a service facility not expressly authorized by VTECH Communications Products purchased more than 12 months from current date HOW DOES STATE LAW RELATE TO THIS WARRANTY e This warranty gives you specific rights You may also have other rights which vary from state to state IF YOU PURCHASED YOUR TELEPHONE IN CANADA Please call Ship to 1 800 267 7377 for return authorization VTECH ELECTRONICS LTD 200 7671 ALDERBRIDGE WAY
4. switch to PULSE NOTE Your VT9119 is preset at the factory for TONE dialing Temporary Tone If you have a rotary dial pulse telephone service TONE PULSE setting is set to PULSE this feature allows you to enter special codes and tones to operate answering machines use electronic banking services calling cards or other special services First dial the call normally Then activate the Temporary Tone feature by pressing TONE the key You can then press the numbers or symbols you need and your phone will send the proper signals To end the call press OFF or place the handset back in the base The phone will automatically go back to rotary dial pulse service Programming The Ringer Type The handset ringer is capable of four different types of ringing tones The following sections detail how to change the different tones and to turn off a ringer on the handset To program the handset must be OFF To select a different ringer type do the following e Press PROG e Press the key e Press a key 1 4 to select a ringer type e Press the MEM key to confirm IN CASE OF DIFFICULTY Turning Off The Ringer To turn off the ringer on the handset do the following e Press PROG e Press the key e Press 5 to turn off the ringer e Press the MEM key to confirm e To turn the ringer on again Programming the Ringer Type see Checking The Ringer To check the ringer which is currently programmed do the foll
5. used e This LED also flashes with the cadence of the incoming ring PAGE KEY e Press the PAGE key to page the handset e Press it second time to cancel a page e The base will ring the handset 1 minute before ending the page automatically e The handset can also cancel the page by pressing the OFF key IN USE CHARGE LED PAGE KEY 7 E se U OS SS SSS SS SS SS SSeS CUT REPLACEMENT BATTERY ORDER FORM For VT 9119 Cordless Telephone Name Adress City State Zip Daytime Phone Number ORDER INFORMATION For Model VT 9119 QTY Batteries 19 95 each wees Shipping Handling 4 95 per battery ccc cccccccccscsesssssssssssnssssnnnees METHOD OF PAYMENT DO NOT SEND CASH CHECK M O VISA MASTERCARD DISCOVER AMERICAN EXPRESS Credit Card EXP DATE CARD HOLDER S SIGNATURE PLACE ORDER FORM AND PAYMENT IN ENVELOPE AND SEND TO VTECH COMMUNICATIONS INC 8770 SW NIMBUS AVENUE BEAVERTON OREGON 97008 7195 USA YOU MAY ALSO ORDER BY PHONE CALL 1 800 595 9511 OPERATING INSTRUCTIONS Making Calls Pick up the handset and press PHONE When you hear a dial tone dial the number The PHONE LED will illuminate while the Handset is in use If you make a mistake when dialing press OFF to hang up then press PHONE to get the dial tone again You must always press PHONE before you can dial a call on the handset Answ
6. 55 1111 MEM Storing Pauses in Memory To insert a pause in a phone number press PAUSE The pause is 2 seconds in length For longer pauses press PAUSE two or more times Each additional press indicates an additional 2 second pause If your phone is connected to a PBX you can store the PBX access number and a pause before the phone number For example to store 9 PAUSE 555 1234 in memory location 8 do the following 10 Press PROG Press 8 Press 9 Press REDIAL PAUSE Dial 555 1234 Press MEM Oo BO iS Using REDIAL To REDIAL the last number you called press PHONE then press REDIAL The phone will automatically dial the number Storing a Redial Number into Speed Dial To store the last number you dialed as a Speed Dial number press PROG a location number 0 9 REDIAL MEM The Page Feature From the base unit press PAGE to signal the person at the handset To end the page at the base press PAGE again To end the page at the handset press OFF If the Handset is in use off hock when PAGE is pressed on the Base Unit the Handset will emit one page alert If the Handset is not in use on hook the page alert will continue for approximately 60 seconds This feature is useful in locating a misplaced Handset OPERATING INSTRUCTIONS TONE PULSE Seiting If you have touch tone service on phone line Press PROG MEM to switch to TONE dialing If you have rotary service press PROG MEM to
7. ANY KEY ANSWER 30 CHANNEL OPERATION Q USER S MANUAL VTECH TELECOMMUNICATIONS LTD www viechphones com Printedin China 91 5210 10 00 ISSUED O To help protect lhe environment this product may IMPORTANT SAFETY INSTRUCTIONS When using your telephone equipment basic safety precautions should always be followed to reduce the risk of fire electric shock and injury to persons including the following 1 Read and understand all instructions 2 Follow all warnings and instructions marked on the product 3 Unplug this product from the wall outlet before cleaning Do not use liquid cleaners or aerosol cleaners Use a damp cloth for cleaning 4 Do not use this product near water for example near a bath tub kitchen sink or swimming pool Do not place this product on an unstable cart stand or table The product may fall causing serious damage to the product 6 Slots and openings in the cabinet and the back or bottom are provided for ventilation To protect it from overheating these openings must not be blocked by placing the product on the bed sofa rug or other similar surface This product should never be placed near or over a radiator or heat register This product should not be placed in a built in installation where proper ventilation is not provided 7 This product should be operated only from the type of power source indicated on the marking label If you are not sure of the type of power supply to your hom
8. ad and follow these instructions 1 Use only VTECH battery 80 5074 00 00 2 Do not open or mutilate the battery Released electrolyte is corrosive and may cause damage to the eyes or skin It may be toxic if swallowed 3 Exercise care in handling batteries in order not to short the battery with conducting materials such as rings bracelets and keys The battery or conductor may overheat and cause burns 4 Do not dispose of the battery in a fire The cell may explode The RBRC Seal a The RBRC Seal on the nickel cadmium battery indicates that VTech Communications Inc is voluntarily participating in an industry program to collect and recycle these batteries at the end of their useful lives when taken out of service within the United States and Canada The RBRC program provides a convenient alternative to placing used nickel cadmium batteries into the trash or municipal waste which may be illegal in your area VTech s participation with RBRC makes it easy for you to drop off the spent battery at local retailers participating in the RBRC program or at authorized VTech product service centers Please call 1 800 8 BATTERY for information on Ni Cd battery recycling and disposal bans restrictions in your area VTech s involvement in this program is part of its commitment to protecting our environment and conserving natural resources RBRC is a registered trademark of Rechargeable Battery Recycling Corporation
9. connect the base unit from the telephone jack and connect a different phone If there is no dial tone on that phone either the problem is in your wiring or local service Call your local telephone company YOU GET NOISE STATIC OR A WEAK SIGNAL EVEN WHEN YOU RE NEAR THE BASE UNIT Household appliances plugged into the same circuit as the base unit can sometimes cause interference Try moving the appliance or the base unit to another outlet YOU GET NOISE STATIC OR A WEAK SIGNAL WHEN YOU RE AWAY FROM THE BASE UNIT You may be out of range Either move closer to the base or relocate the base unit The layout of your home may be limiting the range Try moving the base unit to the second or third floor or to some other location THE HANDSET DOES NOT RING WHEN YOU RECEIVE A CALL Ensure that the ringer is turned on 11 Make sure the telephone line cord is plugged firmly into the base unit and the telephone jack Make sure the power cord is plugged in You may be too far from the base unit You may have too many extension phones on your telephone line to allow all of them to ring Try unplugging some of the other phones YOUR CALLER FADES IN AND OUT You may be nearly out of range Move closer or relocate the base YOU HEAR OTHER CALLS WHILE USING YOUR PHONE e Replace the handset in the base cradle wait a few moments and try again Disconnect your base unit from the telephone jack and plug in a reg
10. e consult your dealer or local power company 8 Do not allow anything to rest on the power cord Do not locate this product where the cord will be abused by persons walking on it 9 Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage points or short out parts that could result in a risk of fire or electric shock Never spill liquid of any kind on the product 10 To reduce the risk of electric shock do not disassemble this product If service or repair work is required contact VTech Customer Service at 1 800 595 9511 Opening or removing cabinet parts other than specified access doors may expose you to dangerous voltages or other risks Incorrect reassembling can cause electric shock when the appliance is subsequently used 11 Do not overload wall outlets and extension cords as this can result in the risk of fire or electric shock 12 Unplug this product from the wall outlet When the power supply cord or plug is damaged or frayed If liquid has been spilled into the product If the product has been exposed to rain or water If the product does not operate normally by following the operating instructions Adjust only those controls that are covered by the operating instructions because improper adjustment of other controls may result in damage and will often require extensive work to restore the product to normal operation e If the product has been dropped and the cabinet has been dama
11. ering Calls When an incoming call is ringing the IN USE LED on the base and PHONE LED on the handset will flash To make sure your phone rings when the handset is away from the base please keep the base antenna in the upright position OPERATING INSTRUCTIONS To answer a call when the handset is in the base just pick up the handset To answer a call when the handset is away from the base just press any key on the handset except OFF This is very useful in a dark environment you do not have to fumble around looking for the PHONE key to answer the call Disconnecting To end a call either place the handset back in the base or press OFF on the handset Changing Channels If you notice interference when using your handset press CHAN to switch to a clear channel This function is only available when you are on a Call 4 Press MEM to store the phone number to the key you selected The phone now exits PROG mode and emits a tone Speed Number Dialing 1 Press PHONE to get a dial tone 2 Press MEM and the memory location number key 0 9 For example to dial the number you assigned to key 8 you would press PHONE MEM 8 To Change or Replace a Speed Dial Number To change or replace a stored number in speed dial memory simply enter the new number and store it in the memory location you wish to change For example to change the number stored in memory position 7 to 555 1111 you would press PROG 7 5
12. ged f If the product exhibits a distinct change in performance 13 Avoid using a telephone other than a cordless type during an electrical storm There may be a remote risk of electric shock from lighting 14 Do not use the telephone to report a gas leak in the vicinity of the leak SAVE THESE INSTRUCTIONS oa Top 2 CZENIE eonialn recycled or nmcondibioned parts and materials INTRUDUCTION Parts Check List To purchase replacement battery packs call 1 Handset VTECH Communications at 1 800 595 9511 3 ae PERET In Canada call VTECH Electronics at 1 800 3 elepnone line cor 5 4 Battery Pack eet tel 5 AC adapter TELEPHONE CORD BATTERY PACK AC ADAPTER REPLACING THE HANDSET BATTERIES 1 Slide the battery cover off by gently pressing onthe recessed area with a downward motion 2 Unplug and remove the old battery pack Don t put the old battery pack in a trash compactor or a fire it could burst y 3 Plug in the replacement battery pack Place the battery pack in the compartment with the battery cord resting on top of it 4 Replace the battery cover by sliding it into place 5 The new battery pack must be charged before using your telephone Place the handset in the cradle of the base unit to allow it to charge for i 16 hours Maximum battery life between charges is more than 5 hours of continuous talk time or 6 days of standby CAUTION To reduce the risk of fire or injury re
13. lectrician as appropriate Notice The REN assigned to this device denotes the number of devices you may connect to the telephone loop which is used by the device to prevent overloading The termination on a loop may consist of any combination of devices subjected only to the requirement that the sum of the REN does not exceed five 5 0 This device complies with RSS 210 of Industry Canada Operation is subject to the following two conditions 1 this device may not cause interference and 2 this device must accept any interference including interference that may cause undesired operation of the device MAINTENANCE TAKING CARE OFYOURTELEPHONE Your VT9119 cordless telephone contains sophisticated electronic parts so it must be treated with care Avoid rough treatment Place the handset down gently Save the original packing materials to protect your telephone if you ever need to ship it Avoid Water Your telephone can be damaged if it gets wet Do not use the handset outdoors in the rain or handle it with wet hands Do not install your base unit near a sink bathtub or shower Remember that electrical appliances can cause serious injury if used when you are wet or standing in water If your base unit should fall into water DO NOT RETRIEVE IT UNTIL YOU UNPLUG THE POWER CORD AND TELEPHONE LINE CORDS FROMTHE WALL Then pull the unit out by the unplugged cords Electrical Storms Electrical storms can sometime
14. owing e Press PROG e Press the key e Press 0 e Press the MEM key to confirm Memory Dialing The VT9119 can store up to 10 different phone numbers that you can dial just by pressing phone MEM and one of the number keys 0 9 Programming Speed Dial Numbers The handset must be OFF 1 Press PROG The PHONE LED will blink to indicate that you are in the programming mode 2 Press the number of the memory location you wish to store the number in 0 9 3 Using the dial pad dial the number you want to store The number can be up to 16 digits long The number can be entered manually or by using REDIAL If you have difficulty operating your phone the suggestions below should solve the problem If you still have difficulty after trying these suggestions In the US Call VTECH Communications at 1 800 595 9511 In Canada Call VTECH Electronics at 1 800 267 7377 THE PHONE DOESN T WORK AT ALL Make sure the power cord is plugged in Make sure the telephone line cord is plugged firmly into the base unit and the telephone wall jack Make sure the batteries are properly charged If the handset makes two beeps the batteries need charging If the IN USE indicators do not light when you press PHONE you must charge the batteries If you recently installed a new battery pack make sure it is installed correctly NO DIAL TONE First check all the suggestions above If you still don t hear a dial tone dis
15. phone lines HANDSET FEATURES PHONE LED The PHONE LED lights when the handset is on an active call e It flashes in cadence with an incoming ring e It flashes quickly during PROG mode e It flashes slowly when battery is low PHONE KEY FLASH KEY e Press the PHONE key to make a call e If you are currently on a call pressing PHONE flashes the line This would be used with a feature like call waiting to answer your second call PROG KEY e Press PROG key to enter PROGRAM mode See Programming Speed Dial Numbers for more details VOLUME CONTROL e Ajust volume of what you hear through the handset While on a call press the Up or Down key to adjust the listening volume The Handset will emit a double beep when the maximum or minimum volume level has been reached OFF KEY e Press the OFF key to exit all modes of operation REDIAL PAUSE KEY When you hear the dial tone pressing the REDIAL key will dial out the last number that wascalled on your phone Itcan also be used to store the last number dialed into the speed dial memory See Storing a Redial Number into Speed Dial for details You can store a PAUSE into your dialing number See Storing Pauses in Memory for detail CHAN KEY e Pressing the CHAN key when the handset is in use will activate a channel change to the next free channel e This is used if you are experiencing noise or interference on the current channel MEM KEY e Press
16. s cause power surges harmful to electronic equipment For your own safety use caution when using electric appliances during storms Cleaning your telephone Your telephone has a durable plastic casing that should retain its luster for many years Clean it only with a soft cloth slightly dampened with water or a mild soap Do not use excess water or cleaning solvents of any kind TECHNICAL SPECIFICATIONS FREQUENCY CONTROL Crystal Controlled Dual PLL Synthesizer TRANSMIT FREQUENCY Handset 923 10 MHz to 927 75 MHz Base 902 3 MHz to 906 65 MHz RECEIVE FREQUENCY Handset 902 3 MHz to 906 65 MHz Base 923 10 MHz to 927 75 MHz NOMINAL EFFECTIVE RANGE Maximum power allowed by FCC and IC Actual operating range may vary according to environmental conditions at the time of use SIZE Handset 17 5cm x 5 5cm x 3 9cm L x W xT maximum antenna excluded Base 19 3cm x 14 8cm x 5 4cm L x W x T maximum antenna excluded WEIGHT Handset 146 grams Base 283 grams POWER REQUIREMENTS Handset Self contained nickel cadmium rechargeable battery supply 3 6V nominal 400mAh capacity Power Adapter 9V DC 200mA SPECIFICATIONS ARETYPICAL AND MAY CHANGE WITHOUT NOTICE
17. terference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet or on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help FCC Part 68 The FCC requires that you connect your cordless telephone to the nationwide telephone network through a modular telephone jack USOC RJ11C or RJ11W Your telephone company may discontinue your service if your equipment causes harm to the telephone network They will notify you in advance of disconnection if possible During notification you will be informed of your right to file a complaint with the FCC If itis determined that your telephone equipment is malfunctioning the FCC requires that it not be used and that it be unplugged from the modular jack until the problem has been corrected Repairs to this telephone equipment can only be made by the manufacturer or its authorized agents or by others who may be authorized by the FCC For repair procedures follow the instructions outlined under the VTECH Limited Warranty 14 The REN is useful in determining the number of devices you may connect to your telephone line and still enable the devices to ring when you receive a call The general rule is that the REN value should not exceed 5 0 total however contact your local telephone company for
18. the MEM key to enter MEMORY mode The sequence for dialing out a speed dial number in memory is PHONE MEM Number Button 0 9 TONE KEY In PULSE dialing mode this key is used to switch to Temporary TONE dialing mode WALL MOUNTING Se 1 Choose a spot near an electrical outlet and a telephone jack Your phone requires a modular telephone jack and a standard electrical outlet 120V AC The power cord is six feet long make sure there is an electrical outlet within reach of the base The outlet should not be controlled by a wall switch If the switch is ever turned off the phone will not operate 2 Mount the base on the wall Position the base so the mounting studs will fit into the holes at the back of the base Position the power cord to extend down the wall the phone is to be mounted on Slide the base down on the mounting studs until it locks into place 3 Connect the telephone cord The telephone line cord has a snap in plug at each end Insert one of the plugs into the jack on the bottom of the base Insert the other end of the plug into the wall jack 4 Connect the power cord Plug the DC connector into the DC jack at the rear of the base unit Plug the AC power adapter into an electrical outlet BASE UNIT FEATURES IN USE CHARGE LED e The LED illuminates steadily when the handset is in the base cradle to indicate that the handset battery is being charged e The LED illuminates whenever the handset is being
19. the specific number in your area IC Industry Canada This telephone is registered for use in Canada Notice The Industry Canada label identifies certified equipment This certification means that the equipment meets certain telecommunications network protective operational and safety requirements Industry Canada does not guarantee the equipment will operate to the user s satisfaction Before installing this equipment users should ensure that it is permissible to be connected to the facilities of the local telecommunications company The equipment must also be installed using an acceptable method of connections The customer should be aware that compliance with the above conditions may not prevent degradation of service in situations Repairs to certified equipment should be made by an authorized Canadian maintenance facility designated by the supplier Any repairs or alterations made by the user to this equipment or equipment malfunctions may give the telecommunications company cause to request the user to disconnect the equipment Users should ensure for their own protection that the electrical ground connections of the power utility telephone lines and internal metallic water pipe system if present are connected together This precaution may be particularly important in rural areas Caution Users should not attempt to make such connections themselves but should contact appropriate electric inspection authority or e
20. ular telephone If you still hear other calls the problem is probably in your wiring or local service Call your local telephone company YOU HEAR NOISE IN THE HANDSET AND NONE OF THE KEYS OR BUTTONS WORK Make sure the power cord is plugged in e Your base unit and handset may not be operating on the same channel or security code Place the handset in the cradle for a few moments to reload the security code and reset the channel COMMON CURE FOR ELECTRONIC EQUIPMENT Electronics like people can sometimes get confused If the unit does not seem to be responding normally then try putting the handset in the cradle to re initialize the unit If it still does not seem to respond perform the following steps in the order listed Disconnect the power to the Base Disconnect the Handset battery pack Wait a few minutes Connect power to the Base Reconnect the Handset battery Place the handset in the Base unit cradle If the Handset has not been recently charged allow 8 hours before use OPS COUN WARRANTY STATEMENT WHAT DOES OUR WARRANTY COVER e Any defect in material or workmanship FOR HOW LONG AFTER THE ORIGINAL PURCHASE e One Year WHAT WILL VTECH DO e At our option repair or replace your unit HOW DO I SEND MY UNIT IN OR OUT OF WARRANTY e Call VTECH Electronics customer service for Return Authorization at 1 800 595 9511 e Properly pack your unit Include any cables amp accessories which were
Download Pdf Manuals
Related Search