Viper 671XV Automobile Alarm User Manual
Contents
1. of this guide Pressing A only in Standard Configuration again within five seconds of arming the system will activate the Multi Level Security feature Each time A is pressed again a different security level is selected The different security levels are selected as follows Press Press a a once The siren chirps once The system is armed a second time within five seconds The siren chirps twice followed by a long chirp Zone 2 is now bypassed gt Press A a third time within five seconds The siren chirps three times followed by a long chirp Zone 4 is now bypassed Cy a fourth time within five seconds The siren chirps four times followed by a long chirp Zones 2 and 4 are now gt Press bypassed gt Press A a fifth time within five seconds The siren chirps five times followed by a long chirp All input zones except the ignition are now bypassed note Multi Level Security Arming only applies to a sin gle arming cycle Once the system is disarmed and then re armed all the zones will be active again O 2004 directed electronics inc 13 After each press of the A to reach the next level of security the remote will emit normal arm notification 1 beep and 3 flashes of the Orange LED For easiest operation in reaching each level of security press A immediately after each noti2. Directed Electronics Inc Vista CA 92081 www directed com 2004 Directed Electronics Inc All rights reserved G437V 05 04
3. Place the new battery into the remote control observing the correct polarity When power is returned the remote control will light all icons and generate melodies representing all beeper tones your warranty Your warranty registration must be returned and the bar code serial number must not be removed If the warranty registration is not returned you do not have a warranty It is also necessary to keep your proof of purchase which reflects that the product was installed by an authorized dealer Make sure that you receive the warranty registration from your dealer 4 2004 directed electronics inc fec id notice This device complies with Part 15 of FCC rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesirable operation Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate this device Directed Electronics Inc 436 Series Tested to Comply C with FCC Standards DRW 368 2004 directed electronics inc 5 2 way remote control functions The 2 way remote control buttons are used to send commands to the system The descriptions below reflect the standard config uration for this system The buttons can be custom configured for the user s specific needs by the ins
4. Turn the ignition off and on and try again To enter or exit Valet Mode gt Turn ignition to RUN position then turn to OFF position Press and release the Valet button within 10 seconds The in vehicle status LED will light solid if you are entering Valet Mode and it will go out if you are exiting Valet Mode To activate Panic Mode gt Press and hold k down for one second To exit Panic Mode gt Press k on the remote To activate Silent Mode gt Press briefly before arming or disarming and the confirmation chirp s will be eliminated for that one operation only Location of Valet Button Number of Valet Button pulses for disarming 2004 directed electronics inc 39 The company behind this system is Directed Electronics Inc Since its inception Directed has had one purpose to provide consumers with the finest vehicle security and car stereo products and accessories available The recipient of more than 20 patents in the field of advanced electronic technology Directed is ISO 9001 registered Quality Directed Electronics products are sold and serviced throughout North America and around the world Call 800 274 0200 for more information about our products and services DEI is an ISO 9001 registered company Directed is committed to delivering world class quality products and services that excite and delight our customers driven to excel Dixected ELECTRONICS INC
5. after trigger The 2 way remote will respond with a number of beeps and LED flashes according to whether a pinswitch sen sor activated the alarm and also if NPC is active disarming without a 2 way remote This feature allows you to disarm the security system without the 2 way remote should it be lost damaged or disabled In order to dis arm the system without a 2 way remote you must have the vehicles ignition key and know where the Valet button is located Be sure to check with the installer for the location and the number of presses of the Valet button required to disarm the system To disarm the security system turn the ignition to the ON posi tion Press the Valet button the vanas preset number of times one to five times within 15 seconds After five seconds the system will disarm If the system does not disarm you may have waited too long turn the ignition Off and On and try again Location of Valet Button Number of Pulses 16 2004 directed electronics inc important The unit can be programmed to respond to one to five pulses of the Valet button for the disarm function Be sure to check with the installer for the desired programming The remote will indicate disarm notification with 2 beeps and 3 flashes of the Orange LED silent mode To temporarily turn off the arm or disarm chirps use Silent Mode Simply press aux for less than one second before arming
6. VRS before leaving the vehicle The system will now trigger automatically the next time you or anyone drives the vehicle This helps to protect the vehicle 2004 directed electronics inc 31 if someone takes your keys and 2 way remote by force in a parking lot note If the VRS system is armed while operating the vehi cle and not disarmed prior to leaving the vehicle it is still armed and will trigger the next time the vehicle is driven vrs triggered sequence 32 Fifteen seconds after the last door has closed the in vehicle LED will begin flashing This delay is intended to allow you time to distance yourself from your vehicle in the event of a carjacking Forty five seconds later the siren begins chirping and the park ing lights begin flashing This time could be used to notify au thorities that your vehicle has been hijacked and tell them what the VRS will do next Fifteen seconds after the siren chirps begin the siren s output will change to a continuous blast From this point on when the ignition key is turned off the VRS will immediately turn on the starter kill This will prevent the vehicle from being restarted thus immobilizing it at that spot Three minutes after the constant siren output begins the flashing parking lights and the siren will stop The starter kill will remain active until the system is disarmed If the door is opened or the ignition is turned off and on in an at
7. at 1 800 876 0800 Directed security systems including this unit are deterrents against possible theft Directed is not offering a guarantee or insurance against vandalism damage or theft of the automobile its parts or contents and hereby expressly disclaims any liability what soever including without limitation liability for theft damage and or vandalism Directed does not and has not authorized any person or entity to create for it any other obligation promise duty or obligation in connection with this security system Make sure you have all of the following information from your dealer A clear copy of the sales receipt showing the following Date of purchase Your full name and address Authorized dealer s company name and address Type of alarm installed Year make model and color of the automobile Automobile license number Vehicle identification number All security options installed on automobile VVVVYVVYV VY Installation receipts ii 2004 directed electronics inc table of contents o gt limited lifetime consumer warranty i 2 way remote control diagram 2 standard remote configurations 2 whatisuncluded 3 ci A A sota 3 important information sssessss 3 systemi Maintenance ss ss en pecs nee Ai eo 4 VOUL WATTANTY 554408 AN CE E rate LE AS
8. dealer result ing in a unique easily identifiable siren sound The siren chirps can be either full volume or six decibels quieter than the full alarm blast 2004 directed electronics inc 29 installation options The system has many options that may require extra parts and labor Some of the possibilities are listed here gt Progressive unlocking In most cars with electric power door locks the system can be configured so that when the system is disarmed only the driver s door unlocks A second press of the Ey button unlocks the other doors gt Vehicle Recovery System VRS VRS is an anti carjacking device designed to help in the safe recovery of your vehicle in case of a carjacking Please refer to the Vehicle Recovery System section of this guide for a complete explanation of how the Vehicle Recovery System operates vehicle recovery system vrs 30 The optional VRS feature is designed to ensure that any unautho rized user of your vehicle even if using your keys and 2 way remote will not be able to permanently separate you from your vehicle The VRS cannot prevent a carjacking attempt however it does ensure that if your vehicle is taken by an unauthorized user it will be disabled after several progressive warnings as safely as possible Should a carjacking occur the VRS allows you to concern yourself with your personal safety without worrying about your property 2004 directed
9. ee opte ne ete a daa ata ia 22 tabl OF Zones nie Ma alae Oued che Nantel Peg AU TN 23 interpreting zone diagnostics 23 code hopping osse astet ad cents ies Pweg weeds am 24 high frequency ct A A nn nn S 24 OWNET FECOBMITION 6 ss seeeesessessss ses 25 fapid resume logic voces sra eed 44 ais s Gees eae REE ewes 25 power saver mode sss 26 programming options 26 installation options 30 vehicle recovery system vrs 44 30 arming Ei se nt Sal A A LE 31 vis triggered sequence 32 Cisdtmiing the vise int DAS AE a hea ache Sob ie te 33 glossary Of terms is sed A ea tre ete etes 34 security amp convenience expansions 36 2004 directed electronics inc 1 2 way remote control diagram 2 standard remote configurations 1 3fa aj af SIN Arm Disarm Indicator Orange Receive Transmit Indicator Green Auxiliary Indicator Yellow Siren Indicator Red Arm Button Disarm Button Panic Button Auxiliary Channel Button 2004 directed electronics inc what is included One control module An XHF2 transceiver antenna One 4 button 2 way remote Stinger Doubleguard dual stage shock sensor Re
10. electronics inc Directed has engineered this vehicle security system the Failsafe Starter Kill and the VRS feature to provide the best combina tion of personal safety and property protection available When properly installed the system can never inadvertently stop your vehicle in traffic or on railroad tracks while the vehicle is in oper ation It is unlike other systems that shut down your engine while it is running This system is designed to perform starter in terrupt or starter kill The Failsafe Starter Kill cannot shut down an already running engine it can only prevent an engine from starting in the first place important Any installation that allows this product to shut down a vehicle s engine when it is running is con trary to the product s design and intended usage and Directed hereby expressly disclaims any liability resulting therefrom arming the vrs To arm the VRS turn the ignition to the ON position and press the arm button on the 2 way remote for one second The parking lights will flash and the siren will chirp once This can be done before driving or while driving the vehicle Once the system is armed it will initiate its triggered sequence see below if any door is opened and closed If you are forced from the vehicle the system will trigger as the door is opened and closed This is how the system works to combat intersection carjacking To protect against parking lot carjacking arm the
11. for 60 minutes If the bypassed sensor tries to trigger the system while it is being bypassed the 60 minute bypass period will start over This ensures that a sensor that continually triggers will remain bypassed Doors are covered by NPC differently if the alarm is triggered by an open door for three full cycles the doors will be bypassed until the trigger ceases 2004 directed electronics inc 19 20 note Arming and disarming the system does not reset this function The only ways to reset a bypassed zone are for it to not trigger for 60 minutes or to turn on the ignition If testing your system it is important to remember that the NPC programming can cause zones to be bypassed and appear to stop working If five chirps are heard when dis arming NPC has been engaged If you wish to clear the NPC memory turn the ignition key on NPC is programmable See Programming Options section of this guide This system also supplies outputs that can control convenience options such as remote control trunk release and window automa tion Consult your dealer for available options for your system Channel 2 Trunk release When connected pressing aux for 1 5 seconds will remotely release the vehicle trunk lid Channel 4 auxiliary output When connected pressing and will immediately activate this output to control an additional convenience option Channel 5 auxiliary output When connected pressing and
12. the 508D radar sensor Your security system can then react to any intrusions into this field with the triggered sequence Headlight and Parking Light Automation The 545T Nite Lite will automatically turn on your parking and headlights when it gets dark In addition the 545T will turn your headlights on whenever the windshield wipers are used A 2 way remote func tion can also be used to turn on your parking and headlights for a programmed time Power Trunk Release The channel two output of the system can operate a factory power release for the vehicle s trunk or hatch An additional relay may be required If the factory release is not 2004 directed electronics inc power activated then Directed s 522T trunk release solenoid can often be added Power Window Control Automatic power window control is pro vided with the 529T and 530T systems Mobile Video This system is compatible with Directed Video s MCB1000 Multi Channel Controller featuring on screen secu rity system programming and zone trigger information Valet Start System For the ultimate in convenience the Valet start system can start your vehicle monitor engine functions and power your climate control system with a push of a button Over rev protection open hood lockout brake pedal shutoff and automatic timer shutoff are all included This feature is only for automatic transmission fuel injected gasoline vehicles 543T XHFplus Exte
13. the remote control will send a diagnostic notifi cation as a reminder These diagnostic notifications are 1 Ifa sensor triggered the system the remote will beep 4 times and the Orange and Red LEDs flash 3 times 2 Ifa switch Zone 1 3 5 or 6 triggered the system the remote will beep 4 times the Orange LED will flash 6 times and Red LED will illuminate for 3 seconds 3 Ifthe system was triggered so many times that NPC is active the remote will emit the above notifications with 5 beeps instead of 4 high security disarm This system includes High Security Disarm feature If the system is triggered this feature allows the user to silence the siren and reset the system to the armed state without having to visually checking the system status After receiving an alarm page First press any button on the remote to clear the alarm page 2 Press either the A or d button again and the High Security disarm feature will be activated The siren will be silenced and the system will reset to the armed state 3 Pressing the Ey button once more will fully disarm the system and allow the vehicle to be accessed 2004 directed electronics inc 15 notes The first press of the remote button while the remote is beeping only clears the alarm page no com mand is sent to the vehicle The transceiver transmits immediately upon system trig y up y 8 ger and does not allow disarm during the first 6 seconds
14. when the alarm goes off or trips The triggered response of your system consists of the siren sounding and parking light flashing for the programmed duration Valet Button A small push button switch mounted somewhere inside the vehicle It is used to override the alarm when a 2 way remote is lost or damaged or to enter or exit Valet mode Warn Away Response Lighter impacts to the vehicle will generate the Warning Zone response It consists of several seconds of siren chirps and parking light flashes Zone A zone is a separate input that the alarm can recognize as unique Each input to the system is connected to a particular zone Two or more inputs often share the same zone 2004 directed electronics inc 35 security amp convenience expansions 36 Here we have listed only some of the many expansion options available Please contact your dealer for a complete explanation of all the options available to you Audio Sensor Metal on glass glass cracking and breaking glass each produce distinctive acoustic signatures The 506T audio sensor uses a microphone to pick up sounds and then analyzes them with proprietary acoustic software to determine if the glass has been struck Backup Battery The 520T keeps the system armed triggers the alarm and keeps the starter kill active if main battery power is disconnected Field Disturbance Sensor An invisible dome of coverage is estab lished by installing
15. Hand held 2 way transceiver which operates the various functions of your system Control Unit The brain of your system Usually hidden under the dash area of the vehicle It houses the microprocessor which monitors your vehicle and controls all of the system s functions Fail Safe Starter Kill An automatic switch controlled by the secu rity system which prevents the vehicle s starter from cranking whenever the system is armed The vehicle is never prevented from cranking when the system is disarmed in Valet mode or should the starter interrupt switch itself fail Your system is ready for this feature however installation may require additional labor Input A physical connection to the system An input can be provided by a sensor pinswitch or through an existing system in the vehicle such as ignition or courtesy lights In vehicle status LED A light mounted somewhere in the vehicle It is used to indicate the status of your system It is also used to report triggers and faults in the system or sensors Shock Sensor This is a sensor mounted in the vehicle that is designed to pick up impacts to the vehicle or glass Siren Noise generating device usually installed in the engine compartment of the vehicle It is responsible for generating the chirps you hear as well as the six tones you hear while the alarm is triggered 2004 directed electronics inc Trigger or Triggered Sequence This is what happens
16. MS ANY LIABILITY WHATSOEVER INCLUD ING WITHOUT LIMITATION LIABILITY FOR THEFT DAMAGE AND OR VANDALISM THIS WARRANTY DOES NOT COVER LABOR COSTS FOR MAINTENANCE REMOVAL OR REINSTALLATION OF THE UNIT OR ANY 2004 directed electronics inc i CONSEQUENTIAL DAMAGES OF ANY KIND IN THE EVENT OF A CLAIM OR A DISPUTE INVOLVING DIRECTED OR ITS SUBSIDIARY THE PROPER VENUE SHALL BE SAN DIEGO COUNTY IN THE STATE OF CALIFORNIA CALIFORNIA STATE LAWS AND APPLICABLE FEDERAL LAWS SHALL APPLY AND GOVERN THE DISPUTE THE MAXIMUM RECOVERY UNDER ANY CLAIM AGAINST DIRECTED SHALL BE STRICTLY LIMITED TO THE AUTHORIZED DIRECTED DEALER S PURCHASE PRICE OF THE UNIT DIRECTED SHALL NOT BE RESPONSIBLE FOR ANY DAMAGES WHATSOEV ER INCLUDING BUT NOT LIMITED TO ANY CONSEQUENTIAL DAMAGES INCIDENTAL DAMAGES DAMAGES FOR THE LOSS OF TIME LOSS OF EARNINGS COMMERCIAL LOSS LOSS OF ECONOMIC OPPORTUNITY AND THE LIKE NOTWITHSTANDING THE ABOVE THE MANUFACTURER DOES OFFER A LIMITED WARRANTY TO REPLACE OR REPAIR THE CON TROL MODULE AS DESCRIBED ABOVE Some states do not allow limitations on how long an implied warranty will last or the exclusion or limitation of incidental or con sequential damages This warranty gives you specific legal rights and you may also have other rights that vary from State to State This product may be covered by a Guaranteed Protection Plan GPP See your autho rized Directed dealer for details of the plan or call Directed Customer Service
17. Model 671XV_ gt Owner s Guide Viper limited lifetime consumer warranty Directed Electronics Inc Directed promises to the original purchaser to repair or replace with a comparable reconditioned model any Directed unit hereafter the unit excluding without limitation the siren the remote transmitters the associated sensors and accessories which proves to be defective in workmanship or material under reasonable use during the lifetime of the vehicle provided the following conditions are met the unit was professionally installed and serviced by an authorized Directed dealer the unit will be pro fessionally reinstalled in the vehicle in which it was originally installed by an authorized Directed dealer and the unit is returned to Directed shipping prepaid with a legible copy of the bill of sale or other dated proof of purchase bearing the following information con sumer s name telephone number and address the authorized dealers name telephone number and address complete product description including accessories the year make and model of the vehicle vehicle license number and vehicle identification number All components other than the unit including without limitation the siren the remote trans mitters and the associated sensors and accessories carry a one year warranty from the date of purchase of the same This warranty is non transferable and is automatically void if the original purchaser has not complete
18. as been programmed on the system will passively arm after one hour even if a protected entry has been left open This feature is useful if a door has been left 2004 directed electronics inc 27 28 ajar when leaving the vehicle Forced passive arming ensures that the security system will be armed in every situation note When the system passively arms after one hour the entry point that has been left open and anything con nected to the same zone is bypassed and cannot trigger the system However the remaining inputs to the system are fully operational Automatic Engine Disable AED on or off The purpose of this feature is to protect the vehicle from being stolen at all times regardless of whether or not the alarm is armed If AED is programmed on the starter of the vehicle will be dis abled 30 seconds after the ignition is turned off Once the key is turned off the in vehicle LED will flash slowly one half its normal armed rate to indicate the AED arming cycle Thirty seconds later the starter of the vehicle will be disabled To start the car it will be necessary to disarm the system with the 2 way remote It is also possible to disarm the AED feature by turning the ignition key to the RUN position and pressing the Valet button the programmed number of times AED is disabled when the system is in Valet Mode note This feature will only function if the Failsafe Starter Kill relay has been installe
19. d Full trigger response 30 or 60 seconds This determines how long the full triggered sequence lasts Some states have laws regulating how long a security system can sound before it is considered a nuisance If your installer is programming the 2004 directed electronics inc security system with the Directed Bitwriter the full triggered response can be programmed for any duration ranging from 1 to 180 seconds gt Nuisance Prevention Circuitry on or off Please refer to the NPC section of this manual for a complete explanation of how NPC operates If NPC is programmed off the securi ty system will respond to inputs from any sensor indefinitely note Because many states have laws regulating security systems programming NPC off may cause your system to violate state laws gt Progressive door trigger on or off When the system is armed and a door is opened the system responds with ten chirps prior to beginning the full triggered sequence If an instant trigger is desired the progressive door trigger can be pro grammed off gt Valet pulse count The number of presses of the Valet button required to disarm the security system AED or the VRS system can be programmed from one to five presses The default setting is one press gt Siren tones and chirp volume The output of the Revenger Soft Chirp siren consists of six different tones in sequence Any of these tones can be eliminated by your
20. d the warranty card and mailed it within ten 10 days of the date of purchase to the address listed on the card the unit s date code or serial num ber is defaced missing or altered the unit has been modified or used in a manner con trary to its intended purpose the unit has been damaged by accident unreasonable use neglect improper service installation or other causes not arising out of defects in materi als or construction The warranty does not cover damage to the unit caused by installa tion or removal of the unit Directed in its sole discretion will determine what consti tutes excessive damage and may refuse the return of any unit with excessive damage TO THE MAXIMUM EXTENT ALLOWED BY LAW ALL WARRANTIES INCLUD ING BUT NOT LIMITED TO EXPRESS WARRANTY IMPLIED WARRANTY WARRANTY OF MERCHANTABILITY FITNESS FOR PARTICULAR PURPOSE AND WARRANTY OF NON INFRINGEMENT OF INTELLECTUAL PROPERTY ARE EXPRESSLY EXCLUDED AND DIRECTED NEITHER ASSUMES NOR AUTHORIZES ANY PERSON OR ENTITY TO ASSUME FOR IT ANY DUTY OBLIGATION OR LIABILITY IN CONNECTION WITH ITS PRODUCTS DIRECTED DISCLAIMS AND HAS ABSOLUTELY NO LIABILITY FOR ANY AND ALL ACTS OF THIRD PARTIES INCLUDING ITS AUTHORIZED DEAL ERS OR INSTALLERS DIRECTED SECURITY SYSTEMS INCLUDING THIS UNIT ARE DETERRENTS AGAINST POSSIBLE THEFT DIRECTED IS NOT OFFERING A GUARANTEE OR INSURANCE AGAINST VANDALISM DAM AGE OR THEFT OF THE AUTOMOBILE ITS PARTS OR CONTENTS AND HEREBY EXPRESSLY DISCLAI
21. fication arming while driving Your security system can be armed while driving the vehicle Simply press A on the 2 way remote for two seconds while the vehicle is running The siren will chirp once to indicate that the security system is armed and then once more to indicate that the ignition is on The system will not respond to any input except the door trig gers and the starter kill relay if installed will not be activated Once you have arrived at your destination the system can be disarmed by pressing the d or by turning the ignition Off The siren will chirp twice and the in vehicle status LED will then stop flashing The system can also be disarmed at any time by pressing N The remote will respond with the normal arming response plus a diagnostic notification because the ignition On When disarmed the remote will respond with the normal disarming response disarming 14 To disarm the security system press id You will hear two chirps and the parking lights will flash twice If the power locks are controlled by the system the doors will also unlock The siren chirping either four or five times when disarming indicates Tamper Alert which is described in the Diagnostics Section of this guide 2004 directed electronics inc The remote will indicate disarm notification with 2 beeps and 3 flashes of the Orange LED If disarming after the system has been triggered
22. g door unlocked engine started vehicle violation etc Press to select page On Off One beep is page On Two beeps is page Off When programmed off the remote will not give any notification that a page was received from the vehicle To exit programming mode The remote control will exit programming mode after 2 seconds of inactivity and will emit 2 long beeps using your system The buttons used in the instructions in this manual correspond to the standard configuration Remember this is not the only way your 2 way remote may be set up It can be custom config ured to meet your needs active arming 10 You can arm the system by pressing A of your 2 way remote for one second When the system arms from the vehicle you will hear a short siren sound or chirp and see the parking lights flash once If the power door locks are controlled by the system the doors will also lock While the system is armed the in vehicle s status LED will flash approximately once per second indicating that the system is actively protecting your vehicle If you hear a O 2004 directed electronics inc second chirp after arming and note that the in vehicle s status LED is flashing in groups see the Diagnostics Section of this guide This extra chirp is called Bypass Notification The remote responds to active arming with one beep and the Orange LED will flash 3 times to indicate successfu
23. gered during the arming countdown the 30 second countdown starts over When armed your vehicle is protected as follows gt Light impacts trigger the Warn Away signal When triggered the siren chirps and the parking lights flash for a few seconds gt Heavy impacts trip a Triggered Sequence The sequence consists of the siren sounding continuously and the parking lights flashing for a pre programmed period which can range in duration from 1 to 180 seconds gt If a door is opened the system will immediately start chirping the siren and flashing the parking lights Three seconds later the siren output changes to a continuous blast This progressive response gives you time to disarm the sys tem with your 2 way remote if you inadvertently open the door while the system is armed while still providing instant response even if the door is immediately closed gt Turning on the ignition key will trip the same progressive re sponse as opening a door gt The optional starter kill prevents the vehicle s starter from cranking gt Any full trigger of the alarm system will immediately send an alarm page to your remote informing you that your vehicle should be checked 2004 directed electronics inc multi level security arming Multi Level Security Arming allows you to select which of the system s inputs or sensors will be active and which will be bypassed when the system is armed See Table of Zones section
24. he page notification The next time a button is pressed on the remote control it will send a command to the system 2004 directed electronics inc out of range notification If a command is issued from the remote but the remote is beyond the range of the vehicle to receive the command the remote responds with 2 sets of 3 quick beeps and the Green LED will flash 6 times To enter programming mode Press and hold all four remote control buttons simultaneously until one long beep is heard Programming mode is now entered Beeps On Off Press C to select beeps On Off One beep is notification beeps On Two beeps is notification beeps Off The notification beeps are programmed On from the factory and can be programmed Off if they are not desired When programmed Off the remote will only flash the LEDs as notification of a command page or an alarm page Remote battery low notification Press d to select low battery notification On Off One beep is low battery notification On Two beeps is low battery notifica tion Off The Low battery Beeps are programmed On from the factory and can be programmed Off if they are not desired When programmed Off the remote will not give any notification that the battery charge level in the remote is low 2004 directed electronics inc 9 Page notification The remote control can be programmed to notify the user of a page audibly beeping if the vehicle s status changes e
25. l arming of the system If after 2 seconds the remote beeps once and the Orange and Red LEDs flash 3 times the system has detected an active sensor that should be checked If after 2 seconds the remote beeps once the Orange LED flashes 6 times and the Red LED lights for 3 seconds the system has detected an open door hood or trunk and has been bypassed passive arming The system can be programmed to arm itself automatically called passive arming If the system is programmed for passive arming it will automatically arm 30 seconds after the ignition is turned off and the system detects that you have left the vehicle by opening and closing a door Whenever the system is in its 30 second passive arming countdown the in vehicle status LED will flash twice as fast as it does when the system is armed At the 20 second point of the countdown the siren will chirp to indicate that the system is about to arm At the 30 second point the parking lights will flash to indicate that the system is armed 2004 directed electronics inc 11 12 The remote responds to passive arming with one beep and the Orange LED will flash 3 times to indicate successful arming of the system note If any protected entry point such as a door or a switch protected trunk or hood is open the system will not passively arm unless forced passive arming is pro grammed on See Programming Options section Addi tionally each time a sensor is trig
26. nk release etc will continue to work normally To enter or exit Valet Mode 1 Turn the ignition on N 2 Turn the ignition off E S gt y 3 Press and release the Valet button once within 10 seconds The in vehicle status LED will light solidly if you are entering Valet Mode and it will go out if you are exiting Valet Mode The remote will respond with 3 Orange LED flashes on entering and 2 beeps and 3 Orange LED flashes on exiting Valet Mode O 2004 directed electronics inc To enter or exit Valet Mode using the 2 way remote 1 Open any vehicle door 2 Press 8 3 Press 4 Press A again The in vehicle status LED will light solidly if you are entering Valet Mode and it will go out if you are exiting Valet Mode The remote responds with the normal arm disarm notifications with each remote button press nuisance prevention circuitry Your system has Directed s Nuisance Prevention Circuitry NPC It prevents annoying repetitive trigger sequences due to faulty door pin switches or environmental conditions such as thunder jackhammers airport noise etc Example If the alarm triggers three times within a 60 minute period and each time the same sensor or switch triggers the alarm NPC will interpret those triggers as false alarms After the third trigger NPC ignores or bypasses that sensor or switch along with any other sensors or switches sharing the same zone
27. of the program settings with the factory settings in Bold 2004 directed electronics inc gt Active arming only with the 2 way remote or passive arming automatic arming 30 seconds after the last door has been closed gt Arming disarming confirmation siren chirps on or off gt The ignition controlled door lock feature on or off With this feature on the doors will lock three seconds after the ignition is turned on and unlock when the ignition is turned off The system will not lock the doors when the igni tion is turned on with any door open If your installer is programming the security system with the Directed Bitwriter ignition lock and unlock are independent features and can be programmed separately gt Passive door locking with passive arming or active door locking only when arming with the 2 way remote Passive locking allows the vehicle s doors to lock when the security system passively arms after the 30 second countdown This feature only works if passive arming has been programmed note When programmed for passive arming and active lock if the system is disarmed without a door being opened the system will relock the doors when it passive ly rearms gt Panic mode enabled disabled with the ignition on Some states have laws against siren capability in a moving vehicle gt Forced passive arming on or off If your system is programmed for passive arming and the forced passive arming feature h
28. or disarming and the confirmation chirp s will be elim inated for that one operation only If you want the arm disarm chirps turned off permanently your dealer can do this for you note The Warn Away response to lighter impacts is bypassed if the system is armed using Silent Mode This ensures that no chirps will be emitted by the siren in an area you want chirp free The system is still fully capable of trig gering Only the Warn Away response is bypassed The remote responds with the normal arm disarm notifications in silent mode If the remote has beeps programmed On the remote will beep 2004 directed electronics inc 17 panic mode If you are threatened in or near your vehicle you can attract attention by triggering the system with your 2 way remote Just press for two seconds and you will enter Panic Mode The siren will sound and the parking lights will flash for the programmed siren duration To stop Panic Mode at any time press on the 2 way remote again The remote responds with one flash of the Red LED upon entering Panic Mode and two flashes of the Red LED upon exiting Panic Mode valet mode 18 You can prevent your security system from automatically arming and triggering by using Valet Mode This is very useful when washing the vehicle or having it serviced In Valet Mode the security system will not arm even with the 2 way remote but all convenience functions door locks tru
29. otification to the user notifications are audible beeps and the LED Icons will display the current system status Command Page When a command arm disarm or auxiliary channel from the remote control is sent and received the system will send a command page back to confirm receipt 2004 directed electronics inc 7 Alarm Page If the alarm system is triggered while armed an Alarm Page will be sent to the remote control When the remote receives an Alarm Page the LED icons will display the alarm system status information and the remote control will generate beeps An Alarm Page alert is a series of 10 or 4 rapid beeps and the Red LED will illuminate This will repeat every 100 seconds to alert the user that the alarm system was triggered and will continue until the alarm page is cleared If the shock sensor or optional sensor has triggered the alarm the remote will display the alarm page with 6 Red LED flashes and 10 rapid beeps If the trunk door ignition or hood triggered the alarm the remote will display the alarm page with the Red LED illumi nating for 3 seconds and 4 rapid beeps repeated 5 times Page Recognition Acknowledgement To clear a page alert notification quickly press any button on the remote control This can be performed at any time during or after the page notification has occurred The remote control will not send a command to the system at this time it will only clear future repeats of t
30. pinswitches 2 A heavier impact detected by the shock sensor 3 Door switch trigger 4 For optional sensors 5 Ignition trigger interpreting zone diagnostics Warn Away responses are not reported by arming or disarming diagnostics If you receive a Bypass notification when arming or a Tamper Alert notification when disarming look at the in vehicle status LED Active or triggered zones will be indicated by a pattern of blinks by this LED Example If Zone 3 was active or triggered the in vehicle LED will blink three times with a two second pause Then it will blink three times again and repeat until the ignition is turned on note Your system stores the last two triggered zones in memory If your system has been triggered but the LED has been reset by turning on the ignition your dealer can still recall the last two zones that were triggered Contact your dealer for details 2004 directed electronics inc 23 code hopping The receiver and 2 way remotes each use mathematical formulas called algorithms to change their codes each time the 2 way remote is used This technology has been developed to increase the security of the unit The control unit knows what the next codes should be This helps to keep the 2 way remote in sync with the control unit even if you use the 2 way remote out of range of the vehicle However if the 2 way remote has been pressed many times out of range of the vehicle or if the battery has been
31. reconnected the system will recall the stored state from memory This means if the unit is in Valet Mode and the battery is disconnected for any reason such as servicing the car when the battery is reconnected the unit will still be in Valet Mode This applies to all states of the system including arm disarm VRS and Valet Mode 2004 directed electronics inc 25 power saver mode Your system will automatically enter Power Saver Mode while armed or in Valet Mode after a period of time in which no operation has been performed This lowers the current draw to the vehicle s battery Power Saver Mode takes over under the following conditions gt Power Saver when the system is armed After the system has been armed for 24 hours the in vehicle LED will flash at half its normal rate decreasing the system s current draw gt Power Saver in Valet Mode When the system enters Valet Mode the in vehicle LED illuminates steadily If the vehicle is not used ignition is not turned on for a period of one hour while the system is in Valet Mode the LED will shut off If the system remains in Valet Mode the LED will come back on the next time the ignition is turned on and then back off programming options 26 Programming options control what your system does during normal operation and require few or no additional parts However some may require additional installation labor The following is a list
32. removed it may get out of sync with the control unit and fail to operate the system To re sync the 2 way remote simply press A of the 2 way remote several times within range of the vehicle The alarm will automatically re sync and respond to the 2 way remotes normally high frequency 24 Your system transmits and receives at 434 MHz This provides a cleaner spectrum with less interference and a more stable signal Enjoy a phenomenal increase in range even in areas with high radio interference 2004 directed electronics inc owner recognition Owner Recognition is a feature available exclusively from Directed Using the Directed Bitwriter a hand held program ming tool your dealer can program many of the system settings The programmer makes it possible to program different settings for each 2 way remote that is used with the system Then when ever a specific 2 way remote is used the system will recall the settings assigned to that 2 way remote Owner Recognition lets up to four users of the system have different settings that meet their specific needs It is almost like having four separate alarms in your vehicle one for each user note Owner Recognition cannot be programmed with out a Directed Bitwriter and the necessary software Check with your dealer for more information d oai This Directed system will store its current state to non volatile memory If power is lost and then
33. rnal Receiver Antenna The 5431 XHFplus external receiver antenna can be used to upgrade the trans mitter receiver performance in areas of high radio interference such as military bases airports and hospitals 2004 directed electronics inc 37 38 2004 directed electronics inc Cut along dotted line and fold for a quick and easy reference to keep in your purse or wallet QUICK REFERENCE GUIDE To arm using your 2 way remote gt You can activate or arm the system by pressing on your remote for one second When the system arms you will hear a short siren sound or chirp and the parking lights will flash once If the vehicles power door locks have been connected to the system the doors will lock To disarm using your 2 way remote gt To disarm the system press Ey You will hear two chirps and the parking lights will flash twice If power locks are connected to the system the doors will unlock If the siren chirps either four or five times when disarming see Diagnostics section This is called Tamper Alert Arming while driving gt Press on your remote for two second while the vehicle is running The system will chirp once and then once more to indicate that the ignition is on Disarming without a 2 way remote gt Turn on the ignition Press and release the Valet button the programmed number of times within 15 seconds After five seconds the system will disarm If it does not you may have waited too long
34. taller standard button configurations El Button The System Arm and Multi Level Security Arming functions are controlled by pressing this button for one second SA Button The System Disarm and High Security Disarm functions are controlled by pressing this button for one second Button Silent Mode and an optional auxiliary function are controlled by this button Silent Mode works by pressing this button for less than one second before arming or disarming An optional auxiliary function such as trunk release can be controlled by pressing this button for 1 5 seconds The auxiliary output controls Button The panic feature is controlled by pressing this button for 2 seconds 6 O 2004 directed electronics inc El and Ey Buttons An optional auxiliary convenience or expansion function that you have added to your system can be activated by pressing these buttons simultaneously The auxiliary output controls remote operation The remote start system operates at 434 MHz and incorporates Directed s proprietary XHF2 out board technology transceiver The high frequency combined with Binary Data communication achieves superior range with two way communication system signal paging features A page is the signal the control module sends to the remote control as confirmation of receipt of a command or alarm system status When the remote control receives a page it will generate a page n
35. tempt to restart the car the siren and light flashing will begin again 2004 directed electronics inc disarming the vrs Take the time to familiarize yourself with the VRS triggering se quence and the disarm procedure It is important to recognize and identify the VRS trigger sequence and know how to disarm it in case of accidental activation Once the VRS is armed it does not disarm automatically You must disarm it the next time you operate the vehicle You must disarm it with one of the following procedures If the system has not entered the triggered sequence siren has not started chirping 1 Turn the ignition on OFF LS 2 Press d on the 2 way remote for one second The lights will flash and the siren will chirp twice If the system has entered the triggered sequence siren has begun chirping pressing the disarm button of the 2 way remote will not disarm VRS To disarm the VRS during a VRS trigger sequence oS 1 Turn the ignition on S 2 Press the Valet button the pre Er gt programmed number of times to disarm the VRS system note If the VRS system has begun its chirping sequence the ignition must be turned off then on to disarm If you are driving the vehicle at the time pull to a safe place away from traffic and follow the triggered sequence dis arm procedure 2004 directed electronics inc 33 glossary of terms 34 2 Way Remote
36. un MEL piton 4 TOCA notice nr Fat leu ess eu ist ANR saine 5 2 way remote control functions 6 standard button configurations 6 remote OperatioN sue es iett etidan Ea Ke an ON Casa a 7 system signal paging features 7 out Of Tange notification sr yeni ie dipe sie athe sd Un nt Sie pied aleve Sandee nas aay 9 programming 2 Way remote 9 USINE your System os NWA w ie aioe de ne tin date a cidre We 10 ACTIVE ALINE ES RO AE nn RE ER er foes dees ey 10 multi level security arming 22 13 arming while driving 1 0 eee cece eee 14 disarming so dau a thie eee OR Oo las a lh Reet has 14 high security disiri paapa hates eres Glee ata bere Beek ne amies 15 disarming without a 2 way remote 16 silent modes iii cath ite Areas atten ohare aise ee as ese ea 17 PANG MOMS sessed o ett Pek edt Pa Piles 18 Valet modera yo sit ER O an Ann Renate E a 18 nuisance prevention CIFCUILTY ss 19 auxiliary outputs options 20 diagnostics she nets Roa tele ere Sie Sead Thos Pusan Let Weep re Dee 21 A wove hehe seed ete wie eee nn ententes este age Sat di 21 disarming diagnostics 22 system Status chipet ey
37. urns off however the security system resumes normal monitoring 2004 directed electronics inc 21 disarming diagnostics Extra disarm chirps are the Tamper Alert If four chirps are heard when disarming the system was triggered in your absence If five chirps are heard a zone was triggered so many times that Nuisance Prevention Circuitry has bypassed that zone The in vehicle status LED will indicate which zone was involved See Table of Zones section of this guide The system will retain this information in its memory and continue to chirp four or five times each time it is disarmed until the next time the ignition key is turned on system status chirps The siren will chirp when arming disarming the system The pattern of chirps will audibly report the system s status as described below Action Number of Chirps Description Arm 1 System armed Arm 1 3 second delay 1 System armed with Bypass Notification Disarm 2 System disarmed Disarm 4 System disarmed with Tamper Alert Disarm 5 System disarmed NPC active 22 2004 directed electronics inc table of zones The zone number is the number of in vehicle LED flashes used by the system to identify that input The standard input assign ments are listed below along with spaces to write in any optional sensors or switches you have had installed Zone Number Dealer Installed of LED Flashes Description Options 1 Instant trigger often used for hood trunk
38. venger Soft Chirp six tone programmable siren In vehicle status LED indicator light Push button Valet switch Your warranty registration VVVV VV VV VY Failsafe Starter Kill ready circuitry may require additional labor Congratulations on the purchase of your state of the art vehicle security system This system has been designed to provide years of trouble free operation Due to the complexity of this system it must be installed by an authorized dealer only Installation of this product by anyone other than an authorized dealer voids the warranty All dealers are provided with preprinted dealer certifi cates to verify that they are authorized This owner s guide should help you to get the most out of your system Please take the time to read it prior to using the system 2004 directed electronics inc 3 system maintenance This system needs no specific maintenance beyond 2 way remote control battery replacement The 2 way remote is powered by a 1 5V AAA battery Low Battery Notification If the battery is low and this feature is programmed On the 2 way remote will emit 2 long beeps 5 seconds after a transmission is completed The 2 long beeps will repeat every 25seconds up to 3 times or until a 2 way remote button is pressed Battery Replacement Gently pull the end of the battery door away from the top of the remote control then slide the door up to expose the battery and remove the expired battery
39. will immediately activate this output to control an additional convenience option The remote will respond with a page notification consisting of an output tone once and the Yellow LED will flash 3 times 2004 directed electronics inc This occurs at the remote after the system has received the com mand to activate any of the Auxiliary outputs The microprocessor at the heart of your security system is constantly monitoring all of the switches and sensors that are connected to it It detects any faulty switches and sensors and prevents them from disabling the entire system The micropro cessor will also record and report any triggers that occurred during your absence Refer to the System Status Chirps and Table of Zones charts for diagnostic information arming diagnostics If the security system is armed at the same time that an input is active such as a door opening or sensor triggering you will hear one siren chirp to indicate arming and a second siren chirp to indicate Bypass Notification A Bypass Notification chirp means that the security system ignores the input that was active when the system was armed until that input ceases Three seconds after that input ceases the security system will resume normal monitoring For example if your vehicle has an interior light exit delay and you arm your security system before the interior light turns off you may hear a second Bypass Notification chirp Once the light t
Download Pdf Manuals
Related Search