Ultra Start 600 Automobile Alarm User Manual
Contents
1. Setting 6 Car J ack Mode 1 Door amp Button 1 Flash Activated upon Button 4 or Door open while Ignition is ON 2 Door Button 4 2 Flashes Activated upon Button 4 or Door open or ignition ON and Ignition 3 Car J ack OFF 3 Flashes No Car J ack Functions Press the Valet Switch 6 times to select setting 6 This will be confirmed by 6 LED flashes Press and hold the Valet Switch until you receive the appropriate of park light flashes and or siren chirps Release the Valet Switch Press the Valet momentarily to move to next program step or repeat to change selection Setting 7 Horn 5th Channel 1 5th Channel 1 Flash Pulsed output when activated by button 4 2 Horn Honk 2 2 Flashes Horn Honk Output Full Alarm ONLY 3 Horn Honk 1 3 Flashes Horn Honk with Arm amp Disarm Chirps Press the Valet Switch 7 times to select setting 7 This will be confirmed by 7 LED flashes Press and hold the Valet Switch until you receive the appropriate of park light flashes and or siren chirps Release the Valet Switch Press the Valet momentarily to move to next program step or repeat to change selection Installation Guide O0 TRANSMITTER See Owner s Guide for More Detail on Operations f Press Once to Lock the doors and arm the alarm Hold for Panic Mode Press a second time and hold for Constant Lock Output Press once to unlock the doors and disarm the alarm Press and hold for the Trunk Aux Output Z Press this button2. If the sensor was to sensitive impact the vehicle with less force If the sensor was not sensitive enough impact the vehicle with greater force For best results ensure that the Control Module is mounted securely to the vehicle Test The System Open all the vehicles windows Press the Lock button to arm the system Wait five seconds or until the dome light goes out then reach in through a window and open the door The alarm will then activate repeat on all the doors Test the Shock Sensor again and adjust if necessary Insure that all additional features are working as intended If necessary proceed to Program Mode to adjust the programmable outputs Installation Guide IG OVERVIEW O00 Program mode allows you to adjust the settings and options of your system Your system has been intelligently designed by installers with years of experience The system s default settings do not require any program changes in most cases However this system does incorporate a highly advanced programming system that includes 2 menus with numerous options and settings that can be easily adjusted for custom installations and applications User Settings Page 8 This program menu contains settings that adjust the way the system operates for the user Alarm Settings Page 9 This menu controls addition channel outputs and output timing To Enter Program Mode 1 Make sure ignition is in the off position 2 Within thr
3. the cause of the trigger The diagnostics can then be used to determine what the cause of the trigger was When disarming the alarm the siren horn will chirp 3 times instead of the usual 2 times to indicate the alarm had been triggered The system s LED will also flash in pulses to indicate which input triggered the alarm NOTE LED status will be cleared when ignition is turned ON For proper memory clearing insure to connect the ignition input to the ignition on the vehicle Park Light Flashes LED Flashes Diagnostic Two Flashes Two Flashes Shock Sensor Triggered Three Flashes Three Flashes Door Input Triggered Four Flashes Four Flashes Ignition Input Triggered Five Flashes Five Flashes Hood Input Triggered None Off System Disarmed None On Solid Valet Mode None Single Flashes System Armed None Rapid Flashes Passive Arming Note While the system is disarmed and the ignition is in the off position the LED will activate from the following triggers 1 The door is opened The LED will Stay on until the door is closed 2 The hood is opened The LED will stay on until the hood is closed 3 The Shock Senor The LED will flash when impact is detected 4 The Aux Sensor The LED will flash when the input is triggered
4. times to select setting 3 This will be confirmed by 3 LED flashes Press and hold the Valet Switch until you receive the appropriate of park light flashes and or siren chirps Release the Valet Switch Press the Valet momentarily to move to next program step or repeat to change selection Setting 4 Horn Honk Timing 1 5ms 1 Flash Short Quiet Pulses 2 20ms 2 Flashes Long Loud Pulses 3 10ms 3 Flashes Normal Medium Pulses Press the Valet Switch 4 times to select setting 4 This will be confirmed by 4 LED flashes Press and hold the Valet Switch until you receive the appropriate of park light flashes and or siren chirps Release the Valet Switch Press the Valet momentarily to move to next program step or repeat to change selection Setting 5 4th Channel Settings 1 Pulsed 1 Flash Pulsed for 0 75 seconds upon 4th Channel Activation 2 Latched 2 Flashes Latched until repeated or ignition ON 3 Active 3 Flashes Active for as long as the button is held on Transmitter Press the lock and Star buttons together to activate the 4th Channel output The Shock Sensor and ignition will be bypassed upon 4th channel activation Press the Valet Switch 5 times to select setting 5 This will be confirmed by 5 LED flashes Press and hold the Valet Switch until you receive the appropriate of park light flashes and or siren chirps Release the Valet Switch Press the Valet momentarily to move to next program step or repeat to change selection
5. EW Green Triggers when 12vt circuit is broken 500ma Input Disconnect Negative trigger input 500ma Input Sensor Full Warn Blue si a Negative trigger input 500ma Input Sensor Pre Warn Green Sensor ground output 500ma Output Sensor Ground Black eae a Sensor power output 500ma outputs are low current and are designed to activate relays SATELLITE LINK PLUG 500ma Output Sensor Power Red Installation Guide Recommended Pre Installation Procedures BEFORE STARTING INSTALLATION Discuss the optional features with the customer Take a few minutes to review the installation and owners manuals Do a walk around the vehicle and check for any damage If installing a LED discuss the placement with customer before installing Recommended Installation Procedures Mounting the Module Never mount the module in the engine compartment Select a location under the dash to install the main module Be certain that the module is securely attached and does not obstruct any serviceable areas Mount the module so that it cannot be seen if looking under the dash as it could be easily unplugged by a thief The module must be free from all moving parts such as brake clutch and gas pedals and the linkages that are attached to them Installing The Led Choose a location that will be highl
6. LTT GUIDE m O 0 0 Advanced Vehicle Security system lt WWW ULTRASTARTERS COM A ee CT TECH SUPPORT E Mail Tech Support SUpport ultrastarters com Check Our Web Site www ultrastarters com Installation Guide Table Of Contents Page 2 600 Wiring Diagram Page 3 Installation Tips Page 4 Pre Installation Suggestions Installation Suggestions Mounting The Module Installing The LED Installing The Program Button Connecting The Starter Disable Connecting The Dome Light Supervision Under Hood Connections Mounting The Siren Wire Connectors Page 5 14 Pin Main Harness Connector 4 Pin Red Connector Keyless Entry 2 Pin Connector Red Plug in LED 2 Pin Blue Connector Plug in Program Button 3 Pin White Connector Aux outputs 4 Pin White Connector Addition sensor input Installation Page 6 7 Basic Installation Quick start Shock Sensor Programming Test The System Programming Page 7 9 Program Overview amp System Reset Program Menu 1 User Settings Program Menu 2 Alarm Settings Operations Page 10 Single amp Dual Car Operation Transmitter Programming Battery Replacement Other Features Page 11 System Service Mode Components _ Control module Remote transmitter s 14 pin main harness with dual 30amp power inputs 4 pin Keyless Entry harness with Driver s Door Priority output 4 pin Aux sensor harness Plug in Valet Switch Plug in Led S
7. TIVATED 1 Press amp Release button 4 2 Press amp Hold Button 4 for 6 seconds until Status LED comes on Steady NOTE The siren will chirp 5 times as confirmation SERVICE MODE DEACTIVATED 1 Press amp Release button 4 2 Press amp Hold Button 4 for 6 seconds until Status LED turns off NOTE The siren will chirp 2 times as confirmation Anti Car J acking Mode Se Eee PNSURE THAT USER IS FULLY TRAINED ON THIS FEATURE II KKI IK k kkk ONLY PROGRAM THIS FEATURE WHEN SPECIFICALLY REQUESTED ENSURE THAT USER IS FULLY TRAINED ON THE OPERATION OF THIS FEATURE IF THE USER IS NOT TRAINED ON THE USE OF THIS FEATURE UNWANTED RESULTS MAY ARISE When activated the system waits 30 seconds then flashes LED rapidly for 30 seconds then chirps the siren as awarning for 10 seconds then goes into full alarm ACTIVATING CAR JACK MODE Program Menu 2 Setting 5 Mode 1 amp 2 While ignition is ON press and release the button Mode 1 amp 2 The door is opened while the ignition is ON Mode2only Each time ignition is turned ON DEACTIVATING CAR JACK MODE 1 During the countdown period Turn ignition ON then press and release the Program Button 2 After full alarm Turn ignition Off then ON then press and hold the Program Button for Eight seconds Installation Guide CAQ PAGNosTic Alarm Diagnostics If the alarm system is triggered while armed the system will retain in memory
8. ammable menu 2 setting 3 Green Door Input Negative door pin switch input Purple Door Input Positive door pin switch input Test for door pin type Positive or Negative then connect the appropriate wire Green or Purple When all the connections are done the control module can be plugged in Before connecting the control module make sure the ignition is in the OFF position Plug in the 6 pin harness then the 14 pin followed _ by any other connectors that were used Step 3 Program Test And Adjust The Shock Sensor To program the Shock Sensor 1 Press andrelease Lock button Five times 2 The system will chirp and the park lights will flash three times then stay ON 3 Within 10 seconds impact vehicle in a safe place i e Window pillar with amount of force wanted to activate alarm The siren will chirp upon learning the impact 4 The Shock Sensor is now programmed 5 Press the Unlock button to exit the Program Mode To test the Shock Sensor 1 Press the Lock button once to arm the system 2 Wait five seconds then impact the vehicle Lighter impacts to the vehicle should trigger the warn away The siren will chirp three times A harder impact to the vehicle will trigger the full alarm The siren will activate for 60 seconds then turn off 3 To deactivate the alarm when triggered press the unlock button twice To adjust the Shock Sensor 1 Repeat the shock sensor learning
9. e See Page 7 for details on entering Program Mode Setting 1 Car Finder 5th Channel 1 CarFinder OFF 1 Light Flash Car Finder Mode Disabled 2 Car Finder ON 2 Light Flashes Car Finder Mode Enabled Note To operate the 5th channel on button 4 setting 7 must be programmed for 5th channel output Press the Valet Switch 1 time to select setting 1 This will be confirmed by 1 LED flashes Press and hold the Valet Switch until you receive the appropriate of park light flashes and or siren chirps Release the Valet Switch Press the Valet momentarily to move to next program step or repeat to change selection Setting 2 Secure Valet Mode 1 Secure Valet Active 1 Flash Valet only if ignition ON and valet switch held for 15 seconds 2 Normal Valet Active 2Flashes Valet if ignition ON and valet switch held for 5 seconds Press the Valet Switch 2 times to select setting 2 This will be confirmed by 2 LED flashes Press and hold the Valet Switch until you receive the appropriate of park light flashes and or siren chirps Release the Valet Switch Press the Valet momentarily to move to next program step or repeat to change selection Setting 3 Park Light Output 1 30 Second Parking Lights on Disarm 1 Flash Park Lights on for 30 seconds on disarm 2 Negative Park Light 2Flashes Switches the Park Light and the Trunk Release 3rd Channel Outputs 3 Normal Parking Lights 3Flashes 2 Park Light Flashes on disarm Press the Valet Switch 3
10. ed Grey Trunk Release Negative output for trunk release 500ma max Yellow Ignition Input Input from vehicles ignition wire Black Ground Input System ground input Red Main Power Input Constant 12 Volt input Green Door Lock Door Lock Output Programmable menu 1 setting 3 Red 12 Volt Output Output for voltage inverter Low Current Only Blue Door Unlock Door Unlock Output Programmable menu 1 setting 3 Pink Second Unlock Second Unlock Output Programmable menu 1 setting 3 Plug in Program Button Connector The program Button is used to access the systems Programming Menu s See page 5 for installation instructions Plug in LED Connector See page 5 for installation instructions Green When Disarmed Negative output when disarmed Pink Horn Channel 5 Programmable See menu 2 setting 7 Blue Disconnect Triggers when 12volt circuit is broken Blue Sensor Full Warn Input trigger for addition alarm sensor s Green Sensor Pre Warn Input trigger for addition alarm sensor s Black Ground Output Ground output for addition alarm sensor s Red 12 Volt Output 12 volt output for additional alarm sensor s Satellite link connector Installation Guide SOW QUICK STAF Black Ground Input System ground input Yellow Ignition Input Input from vehicles ignition wire Red Main Power Input Constant 12 Volt input Brown Siren Output Positive output for siren White Park lights Park light output Progr
11. ee seconds turn the key ON OFF ON OFF ON Leave in the ON position 3 Press and release the Program Button one time 4 Park lights will come and the siren will chirp to confirm entering Program Mode 5 Select Desired Program Menu by the following Press Button 1 Lock User Options Page 8 Press Button 2 Unlock Alarm Settings Page 9 6 The selected mode will be confirmed by a siren chirp and one park light flash 7 The Program Menu may be changed at any time by pressing the transmitter buttons as above this allows the installer to change a setting from one menu then quickly jump to another menu and change another setting without re entering the Program Mode 8 Program Mode will be exited if there is no activity for 30 second or if the key is turned to the Off position This will be confirmed by one long siren chirp and park light flash Note f unit does not enter Program Mode turn ignition off for 5 seconds and repeat steps 1 4 The ignition wire Yellow MUST be connected to the vehicle s ignition wire If it is not connected it will not be possible to enter the Program Modes To Select and Change A Program Setting 1 Enter Program Mode 2 Select the desired Program Menu See pages 8 amp 9 3 Press amp release the Program Button the correct number of times to select the desired Program Setting as listed on pages 8 amp 9 The park lights will flash and the siren will chirp to indicate the current s
12. etting that is selected 4 Press and hold the Program Button until the parking lights siren confirm the selected setting The park lights will flash and the siren will chirp to indicate the option selected within the setting 5 Turn the ignition key Off to exit Program Mode NOTE This procedure is listed in detail below each program setting on pages 8 amp 9 of this manual SYSTEM RESET STEP 1 Within three seconds turn the key ON OFF ON OFF ON Leaving the Key ON STEP 2 Press and release the Program Button STEP 3 Park Lights will come ON STEP 4 Press the Program Button a second time and hold for 8 seconds until the park lights flash 3 times and siren chirps 3 times System is now re set to factory defaults NOTE Reset to defaults does not delete the transmitters from memory Installation Guide SOO PROGRAMMI PROGRAM MODE USER SETTINGS Enter User Program Mode See Page 7 for details on entering Program Mode Setting 1 Ignition Auto Lock 1 Ignition Lock amp Unlock Enabled 1 Light Flash Doors Lock Unlock when the key is turned On Off 2 Ignition Lock Only 2 Light Flashes Doors Lock when ignition key is turned ON only 3 Ignition Auto Lock Disabled 3 Light Flashes Doors do not Lock or Unlock with Ignition key Press the Valet Switch 1 time to select setting 1 This will be confirmed by 1 LED flashes Press and hold the Valet Switch until you receive the appropriate of park light flashes and or si
13. ren chirps Release the Valet Switch Press the Valet momentarily to move to next program step or repeat to change selection 1 Lock amp Unlock chirps DISABLED 1 Flash A audible chirp for Panic Mode only 2 Lock amp Unlock chirps ENABLED 2 Flashes Audible chirp for Lock amp Unlock but NO audible indication for Start 3 ALL CHIRPS ENABLED 3 Flashes Audible chirp indication for Lock Unlock and Start Press the Valet Switch 2 times to select setting 2 This will be confirmed by 2 LED flashes Press and hold the Valet Switch until you receive the appropriate of park light flashes and or siren chirps Release the Valet Switch Press the Valet momentarily to move to next program step or repeat to change selection 1 Double Pulse Unlock 1 Flash A single 75 second lock and double unlock pulse 0 25 pulse amp 0 75 2 3 Second Lock amp Unlock 2 Flashes 3 second pulses for lock amp unlock 3 0 75 Second Pulses 3 Flashes 0 75 second pulses for lock and unlock Press the Valet Switch 3 times to select setting 3 This will be confirmed by 3 LED flashes Press and hold the Valet Switch until you receive the appropriate of park light flashes and or siren chirps Release the Valet Switch Press the Valet momentarily to move to next program step or repeat to change selection 1 SENSORS DISABLED 1 Flash INTERNAL SHOCK SENSOR AND Aux Sensor DISABLED 2 SENSORS ENABLED 2 Flashes INTERNAL SHOCK SENSORS AND AUX SENSOR INPUT ENABLED Pre
14. s to be used must be programmed at the same time All transmitters not programmed at this time will be erased from memory for security The system holds a maximum of 3 transmitter codes including 2nd car remote codes You can program the same remote as a 1st car remote in one vehicle and as a 2nd car remote in a second vehicle Battery Replacement The transmitter battery should be changed at least once every year to maintain proper operating range Replace with quality23A 12volt Alkaline battery Step 1 Step 2 Step 3 Carefully remove the Remove top case Repl reetreniaie to screw from back of then replace the a lt re ie eons a heremo battery e install screw proper operation Installation Guide ACTIVATING SERVICE MODE 1 While the ignition is ON press and hold the Program Button for five seconds The park lights will flash and the siren will chirp five times to confirm that the system is in service Mode 2 While in Service Mode the remote start functions will be disabled and LED s will be ON steady Door locks and trunk release are still operational DEACTIVATING SERVICE MODE 1 While the ignition is ON press and hold the Program Button for five seconds The park lights will flash and the siren will chiro two times to confirm that the system has exited Service Mode 2 Remote start functions will return to normal operation on Service Mode By Remote SERVICE MODE AC
15. ss the Valet Switch 4 times to select setting 4 This will be confirmed by 4 LED flashes Press and hold the ValetS witch until you receive the appropriate of park light flashes and or siren chirps Release the Valet Switch Press the Valet momentarily to move to next program step or repeat to change selection Setting 5 Passive Active Arming 1 Passive Arming 1 Flash Auto Arms 30 seconds after last door is closed 2 Active Arming WithRearm 2 Flashes Arms if unlock is pressed and no door is opened within 30 sec 3 ACTIVE ARMING 3 Flashes ALARM ARMS ONLY WITH REMOTE TRANSMITTER Press the Valet Switch 5 times to select setting 5 This will be confirmed by 5 LED flashes Press and hold the Valet Switch until you receive the appropriate of park light flashes and or siren chirps Release the Valet Switch Press the Valet momentarily to move to next program step or repeat to change selection Setting 6 Active Passive Locks 1 Active Locking 1 Flash Doors do not auto lock with passive arming 2 Passive Locks 2 Flashes DOORS LOCK WHEN PASSIVE ARMING Press the Valet Switch 6 times to select setting 6 This will be confirmed by 6 LED flashes Press and hold the Valet Switch until you receive the appropriate of park light flashes and or siren chirps Release the Valet Switch Press the Valet momentarily to move to next program step or repeat to change selection Installation Guide PROGRAM MODE ALARM SETTINGS Enter Alarm Program Mod
16. tarter Disable harness Multi tone siren Installation guide Owners manual Installation Guide Built in Starter Disable relay See page 5 Programmable Menu 2 Channel 4 Pink Green Connect to hood pin Hood Input Blue Connect to door pin Door Input Purple Connect to park lights 15amp Output Park Lights White See page 6 Input Dome Light Relay BIk White Output Dome Light Relay Blk White Output while armed 500ma Output When Armed Orange Trunk Release Output 500ma Output Trunk Release Connect to main Ignition Input Ignition Input 12vt constant power Input Main Power Red Connect to door pin Input Programmable See menu 1 Setting 3_ 500ma Output Door Lock Output Green _12vt inverter Output Low Current 500ma Output 12vts Low Current Red Programmable See menu 1 Setting 3_ 500ma Output Door Unlock Output E Programmable See menu 1 Setting3 500ma Output Priority Output Valet Switch ee Negative Output When Disarmed 500ma Output When Disarmed Programmable See menu 2 Setting 7 500ma Output Horn Channel 5 mic 2 PIN RED ws 2 PIN BLUE SIDE VI
17. the door is opened For positive door connect one of the black white wires to 12volts and the other to the door pin wire For negative connect one of the black white wires to ground and the other to the door pin wire Under Hood Connections Route the hood pin optional and Siren wire through the firewall into the engine compartment Always try to pull the wires through a factory rubber grommet If drilling through the firewall BE CAREFUL Check for obstructions on both sides of the firewall After drilling use a snap in grommet to protect the wires from sharp edges Mounting The Siren Choose a location in the engine compartment that is away from high heat sources and direct exposer to water The siren should be mounted as well as grounded to solid metal Run the wiring for the siren so that it can not be seen or reached from below the vehicle Installation Guide OIl NNECTORS GOO 14 Pin Connector Pink Channel 4 Output Programmable See menu 2 setting 5 Green Door Input Negative door pin switch input Blue Hood Input Negative input from hood pin switch Purple Door Input Positive door pin switch input Brown Siren Output Positive output for siren White Park lights Park light output Programmable menu 2 setting 3 Blk White Dome Light Dome light supervision See page 5 Blk White Dome Light Dome light supervision See page 5 Orange When Armed Negative output when system is arm
18. to activate the 4th channel output First Car This output can be used to activate additional alarm features Press once and hold for Car Finder Press and release then hold to activate deactivate Service Mode Second Car Operation tt amp Press Once to Lock the doors and arm the alarm Hold for Panic Mode Press a second time and hold for Constant Lock Output Soe amp __ Press once to unlock the doors and disarm the alarm Press and hold for the Trunk Aux Output 2nd Car Sue amp Kk Press this button to activate the 4th channel output This output can be used to activate additional alarm features ab then ajila then ajila Press once and hold for Car Finder Press and release then hold to activate deactivate Service Mode Step 1 Within three seconds turn the ignition Key ON OFF ON OFF ON Leaving Key ON Step 2 Press and hold the Program Switch Parking Lights will come ON if park lights do not come on at this point turn key off for 5 seconds then repeat step 1 Step 3 Continue to hold the Program Switch until park lights go out Step 4 Press the LOCK button on each of 1st car remote s and press the button on each of the 2nd car remote s of the transmitters to be programmed The park lights will flash once and the siren will chirp once each time a new code is learned Note Transmitter programming must done quickly Do not pause more than one second between each transmitter All the transmitter
19. y visible when the LED is installed Most vehicles are equipped with knock out panels in the dashboard these panels are easily removable and can be easily replaced if necessary Once the location is picked use a 5 16th drill bit and drill a hole through the panel Test fit the LED into the hole If the hole was drilled to large place the LED in the hole and glue in place from the back of the panel Plug the Led into the Red connector on the main module Installing The Program Button Choose a location to mount the Program Button This location should be hidden and not visible from outside the vehicle Once the location of the switch is picked use a 1 4 drill bit and drill a hole Remove the nut and push the Program button through the hole Replace the nut and tighten until the switch is secure Plug the valet into the Blue connector of the main module Connecting The Starter Disable Take the brown starter kill wire from the box and cut in half then locate the vehicles starter wire This wire will switch to 12volts in the crank or start position only Cut this wire in half and confirm that the vehicle will not start Connect the brown wires one to each side of the cut starter wire Route the brown wires to the main module and connect to the starter kill plug Connecting The Dome Light Supervision Determine the door pin type Positive door pin wire switches to 12 volts when the door is opened Negative door pin wire switches to ground when
Download Pdf Manuals
Related Search