Transition Networks CPSMM-120 Network Card User Manual
Contents
1. 0 Bo a EEL Redundant Management Two CPSMM 120 management modules may be installed in the same network In this set up the two modules auto negotiate where one is the primary module while the other is in stand by mode If the primary module fails the stand by module automatically takes over and manages the network Replacing the CPSMM 120 The CPSMM 120 can be hot swapped that is the CPSMM 120 can be replaced while the PointSystem chassis is powered However please note that e If there are two management modules installed in the same network the stand by module will continue to manage the network while the primary module is replaced Also the stand by module will retain all network settings e If there is only one management module installed all SNMP management operations will cease once the module is removed The newly installed management module must be reconfigured to resume network management For more information on installing and replacing the CPSMM 120 see the user s guide for the chassis in which the module will be installed The chassis manuals can be found on the Transition Network website at www transition com techsupport transition com Click the Transition Now link for a live Web chat 3 CPSMM 120 Network Management CPSMM100 Firmware The Transition Networks CPSMM100 firmware is embedded in the CPSMM 120 management module The firmware includes e aCommand Line Inter2. MM 120 to which this declaration refers are in conformity with the following standards CISPR 22 1993 EN 55022 1998 Class A EN 55024 1998 FCC Part 15 Subpart B the undersigned hereby declare that the equipment specified above conforms to the above Directive s and Standard s Pe Clan ee May 2007 Stephen Anderson Vice President of Engineering Date 24 hour Technical Support 1 800 260 1312 International 00 1 952 941 7600 techsupport transition com Click the Transition Now link for a live Web chat Compliance Information CE Mark FCC Regulations This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at the user s own expense Canadian Regulations This digital apparatus does not exceed the Class A limits for radio noise for digital apparatus set out on the radio interference regulations of the Canadian Department of Comm
3. NK Link A link has been established via the DB 9 serial port or the RJ 45 Ethernet port 4 RX LNK RX Receive The management module is E receiving data via the DB 9 serial E port or the RJ 45 Ethernet port hz TX Transmit The management module is transmitting data via the DB 9 serial port or the RJ 45 Ethernet port Reset Switch The CPSMM 120 has a reset switch which only resets the management module not the entire chassis in which the module has been installed Technical Specification For use with Transition Networks Model CPSMM 120 or equivalent Standards CISPR 22 1993 Class A CE Mark Dimensions 3 4 x 0 86 x 5 0 86 mm x 22 mm x 127 mm Weight 3 oz 91 g approximate Power Consumption 2 4 Watts MTBF 243 000 hours MIL217F2 V5 0 MIL HDBK 217F 1 241 000 hours Bellcore7 V5 0 Environment Tmra 0 to 60 C 32 to 140 F Storage Temp 20 to 85 C 4 to 185 F Humidity 10 to 90 non condensing Altitude 0 to 10 000 feet Warranty Lifetime Manufacturer s rated ambient temperature Tmra range for these management modules depend on the physical characteristics and the installation configuration of the Transition Networks PointSystem chassis in which the modules will be installed See the user s guide for the chassis in which these modules will be installed for temperature related installation constraints WARNING Visible and invisible laser radiation when open Do not stare int
4. ans TRANSITION User s Guide CPSMM 120 Single Slot Master Management Module Transition Networks CPSMM 120 Single Slot master management module enables network management of a single PointSystem chassis CPSMC0200 2x0 CPSMC0800 100 CPSMC13xx 100 CPSMC18xx xxx and CPSMC19xx 100 and any installed media converter slide in modules The CPSMM 120 includes Transition Networks CPSMM100 firmware embedded in the module which can be accessed via the DB 9 serial port or the 10Base T RJ 45 Ethernet port Installing the CPSMM 120 3 Network Management 4 OPE AMON ise ss srs enen E ai 4 Technical Specifications 5 Troubleshooting 6 Contact US s adisi adia obese Suse ae 7 Compliance Information 8 CPSMM 120 CPSMM 120 Single Slot Master Management Module Installing the CPSMM 120 The figure below illustrates the components of the CPSMM 120 management module e A panel fastener screw that secures the management module to the Pointsystem chassis e PWR power LINK RX receive and TX transmit LED indicators e A reset switch which resets ONLY the CPSMM 120 management module not the chassis in which it is installed e A 10Base T RJ 45 Ethernet port through which the management module communicates using the Ethernet network with a remote Network management Station NMS or with a Telnet connection e A DB 9 serial port through which the managemen
5. face CLI e a Telnet server e a Web browser and e an SNMP agent Each of these applications can be accessed either through the module s DB 9 serial port or RJ 45 Ethernet port which allows the network administrator to monitor and control the network from an attached terminal or from a remote location FocalPoint 2 0 Management Application Transition Networks Foca Point 2 0 management application can be installed in a networked computer to provide a graphical user interface to monitor the network The version on the enclosed CD supports all features of the enclosed CPSMM100 firmware as well as all Transition Networks slide in modules that are available at the time the CD was produced NOTE For detailed information on how to e Set up and configure a network using the CPSMM100 firmware e Use the command line interface Telnet server or Web browser e Install and use the Foca Point 2 0 management application See the FocalPoint 2 0 Management Application and CPSMM100 Firmware User s Guide on the enclosed application CD It can also be viewed on the Transition Networks website at www transition com Operation LED Indicators The CPSMM 120 management module has four status LEDs which are used to monitor the operation of the management module in the network Operation continued LEDs indications continued PWR Power The management module iS mma receiving power from the chassis TX PWR L
6. munikationsnetz in den EG Mitgliedstaaten verst sst gegen die jeweligen einzelstaatlichen Gesetze zur Anwendung der Richtlinie 91 263 EWG zur Angleichung der Rechtsvorschriften der Mitgliedstaaten ber Telekommunikationsendeinrichtungen einschliesslich der gegenseitigen Anerkennung ihrer Konformit t Trademark Notice All trademarks and registered trademarks are the property of their respective owners Copyright Restrictions 2001 2004 2005 Transition Networks All rights reserved No part of this work may be reproduced or used in any form or by any means graphic electronic or mechanical without written permission from Transition Networks Printed in the U S A 33203 F
7. o the beam or view the beam directly with optical instruments Failure to observe this warning could result in an eye injury or blindness WARNING Use of controls adjustments or the performance of procedures other than those specified herein may result in hazardous radiation exposure The information in this user s guide is subject to change The most up to date revision of the CPSMM 120 user s guide can be viewed at www transition com 4 24 hour Technical Support 1 800 260 1312 International 00 1 952 941 7600 techsupport transition com Click the Transition Now link for a live Web chat 5 CPSMM 120 Troubleshooting If the management module fails isolate and correct the failure by determining the answers to the following questions and then taking the indicated action 1 Press the Reset button on the management module Does the fault resolve itself NO e Proceed to step 2 Is the PWR power LED on the management module illuminated NO e Is the management module inserted properly into the chassis e Is the chassis properly connected to the external power source e Contact Technical Support US Canada 1 800 260 1312 International 00 1 952 941 7600 YES e Proceed to step 3 Is the LNK copper link LED on the management module illuminated NO e Ifthe DB 9 serial port is being used for data transmission check it for proper connection e Ifthe RJ 45 Ethernet port is being used fo
8. r data transmission check it for proper connection e Contact Technical Support US Canada 1 800 260 1312 International 00 1 952 941 7600 YES e Proceed to step 4 NOTE To Isolate faults involving data transmission Please see the Troubleshooting section of the FocalPoint 2 0 Management Application and CPSMM100 Firmware User s Guide on the enclosed application CD It can also be viewed on the Transition Networks website at www transition com Contact Us Technical Support Technical support is available 24 hours a day US and Canada 1 800 260 1312 International 00 1 952 941 7600 Transition Now Chat live via the Web with Transition Networks Technical Support Log onto www transition com and click the Transition Now link Web Based Seminars Transition Networks provides seminars via live web based training Log onto www transition com and click the Learning Center link E Mail Ask a question anytime by sending an e mail to our technical support staff techsupport transition com Address Transition Networks 6475 City West Parkway Minneapolis MN 55344 U S A telephone 952 941 7600 toll free 800 526 9267 fax 952 941 2322 TRANSITION Declaration of Conformity NETWORKS Name of Mfg Transition Networks 6475 City West Parkway Minneapolis MN 55344 U S A Model CPSMM 120 Single Slot Master Management Module Part Number CPSMM 120 Regulation EMC Directive 89 336 EEC Purpose To declare that the CPS
9. t module communicates with the command line interface feo Panel Fastener Screw Se LEDs RX LNK lt Reset Switch Lasva Amoma E RJ 45 Ethernet Port DB 9 Serial Port qvas oo CPSMM120 Application CD The enclosed application CD contains 1 CPSMM100 Firmware which includes e a Command Line Interface CLI e a Telnet server e a Web browser and e an SNMP agent 2 FocalPoint 2 0 Management Application which can be used to monitor and control the PointSystem chassis from a remote location 3 A User s Guide which describes in detail how to use both the CPSMM100 firmware and the Foca Point 2 0 management application 24 hour Technical Support 1 800 260 1312 International 00 1 952 941 7600 The CPSMM 120 management module is designed to be installed into a Transition Networks PointSystem chassis to enable network management of any media converter slide in modules installed in the chassis The following chassis are available e CPSMC0200 100 2 slot PointSystem chassis e CPSMC0800 100 8 slot PointSystem chassis e CPSMC13xx 100 13 slot PointSystem chassis e CPSMC18xx xxx 18 slot PointSystem chassis e CPSMC19xx 100 19 slot PointSystem chassis The CPSMM 120 management module is installed in one of the Transition Network PointSystem chassis Configuration for the 13 slot 18 slot or 19 slot chassis is shown here 20
10. unications Le pr sent appareil num rique n met pas de bruits radio lectriques d passant les limites applicables aux appareils num riques de la Class A prescrites dans le R glement sur le brouillage radio lectrique dict par le minist re des Communications du Canada European Regulations Warning This is a Class A product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures Achtung Dieses ist ein Ger t der Funkst rgrenzwertklasse A In Wohnbereichen k nnen bei Betrieb dieses Ger tes Rundfunkstdrungen auftreten In diesem Fall ist der Benutzer f r Gegenma nahmen verantwortlich Attention Ceci est un produit de Classe A Dans un environment domestique ce produit risque de cr er des interf rences radio lectriques il appartiendra alors l utilsateur de prende les measures sp cifiques appropri es In accordance with European Union Directive 2002 96 EC of the European pzd Parliament and of the Council of 27 January 2003 Transition Networks will accept post usage returns of this product for proper disposal The contact information for this activity can be found in the Contact Us portion of this document PUBLIC TELEPHONE NETWORK Failure to observe this caution could result in CAUTION RJ connectors are NOT INTENDED FOR CONNECTION TO THE damage to the public telephone network Der Anschluss dieses Ger tes an ein ffentlickes Telekom
Download Pdf Manuals
Related Search