Transition Networks 33423.A Power Supply User Manual
Contents
1. 14 Contact Us 15 Compliance Information 16 Cautions and Warnings Definitions Cautions indicate potential damage to equipment Warnings indicate a potential hazard or injury to people Cautions and warnings in this manual Cautions and warnings are explained here and placed throughout this manual where appropriate NCAUTION While installing or servicing the Power Module wear a grounding device and observe all electrostatic discharge precautions Failure to observe this caution could result in damage or failure of the Power Module Z WARNING Do not connect the Power Module to an external power source before installing it into the chassis Failure to observe this warning could result in an electrical shock even death WARNING A readily accessible suitable National Electrical Code NEC or local electrical code approved disconnect device and branch circuit protector must be part of the building s installed wiring to accommodate permanently connected equipment Failure to observe this warning could result in an electric shock even death WARNING Turn the Power Module and external power source OFF and ensure that the Power Module is disconnected from the external power source before performing any maintenance Failure to observe this wa2. TTT one IONPS A AC Power Module User Manual 33423 A IONPS A AC Power Module Table of contents Cautions and Warnings 3 DEMONS ors obs erik par Seek 5580 gu ala bee 3 Cautions and warnings in this manual 3 Description 4 Power Module component identification 9 4 0005545 255 bios a Rg Web a 5 Installation 5 Power Module redundancy 0 000 cece teens 5 Installing an optional Power Module into the ION chassis 6 Connecting external power cece eee 9 Maintenance 10 Replacing the Power Module 10 Replacing the fuse 12 Technical Specification 200000000 000 cece ee cere nee 13 Troubleshooting
3. a question anytime by sending an e mail to our technical support staff techsupport transition com Address Transition Networks 10900 Red Circle Drive Minnetonka MN 55343 U S A telephone 952 941 7600 toll free 800 526 9267 fax 952 941 2322 TRANSITION NETWORKS Name of Mfg Transition Networks 10900 Red Circle Drive Minnetoka MN 55343 U S A Model IONPS A AC Power Module 120 240 VAC Declaration of Conformity Purpose To declare that the IONPS A AC Power Module to which this declaration refers is in compliance with the following directive s and standard s EMC Directive 2004 108 EC EN 55022 2006 A1 2007 Class A EN55024 1998 A 1 2001 A2 2003 EN6100 2 3 EN6100 3 3 CFR Title 47 Part 15 Subpart B Class A Low Voltage Directive 2006 95 EC EN60950 1 2006 CFR Title 21 Section 1040 10 Class I I the undersigned hereby declare that the model number s listed in this declaration of conformity is in compliance with the Directive s and Standard s herein ee anuary 2010 Stephen Anderson Vice President of Engineering Date 14 Tech Support 1 800 260 1312 International 00 1 952 94 1 7600 24 hours techsupport transition com Click the Transition Now link for a live Web chat Compliance Information FCC Regulations This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to part 15 of the FCC rules These limits a
4. com Click the Transition Now link for a live Web chat IONPS A AC Power Module Troubleshooting If the Power Module fails isolate and correct the failure by determining the answers to the following questions and then taking the indicated action l Is the Power LED on the IONPS A AC Power Module illuminated NO Is the Power Module inserted properly into the chassis Js the Power Module properly connected to the external power source Does the external power source provide power e Contact Technical Support US Canada 1 800 260 1312 International 00 1 952 941 7600 YES e Proceed to step 2 Is the fuse on the IONPS A AC Power Module intact NO e CAUTION See the Replace the Fuse section for the proper method for replacing the fuse to the Power Module e Contact Technical Support US Canada 1 800 260 1312 International 00 1 952 941 7600 YES e Contact Technical Support US Canada 1 800 260 1312 International 00 1 952 941 7600 Contact Us Technical Support Technical support is available 24 hours a day US and Canada 1 800 260 1312 International 00 1 952 941 7600 Transition Now Chat live via the Web with Transition Networks Technical Support Log onto www transition com and click the Transition Now link Web Based Seminars Transition Networks provides seminars via live web based training Log onto www transition com and click the Learning Center link E Mail Ask
5. in the ON position the power ON LED will lite This means that the optional Power Module is ready to power the chassis if the primary Power Module fails Important There is NO power sharing between the two Power Modules Power Module Power Cord Power Module Receptacle ON OFF Switch AC Power Cord AC Power Cord male end female end Figure 7 AC Power Cord Ends 8 Tech Support 800 260 1312 International 00 1 952 941 7600 24 hours techsupport transition com Click the Transition Now link for a live Web chat IONPS A AC Power Module Maintenance Replacing the Power Module N WARNING Do not connect the Power Module to the external power source before installing it into the chassis Failure to observe this caution could result in equipment damage and or personal injury or death To replace the Power Module do the following 1 Turnthe power ON OFF switch to the OFF position 2 Disconnectthe AC power cord from the power source 3 Innecessary remove the chassis grounding assembly See Figure 8 Chassis Frame Nuts amp Washers A Grounding Terminal Not P asa 1109 Not Provided LO DN Figure 8 Chassis Grounding Hardware 4 Remove the two screws securing the Power Module to the chassis 5 Carefully pull the Power Module from the chassis See Figure 9 k Chassis Power Module Figure 9 Removing Power Module 10
6. Tech Support 1 800 260 1312 International 00 1 952 941 7600 24 hours Maintenance Continued Installing the Power Module continued 6 Locate the new Power Module 7 Push the power ON OFF switch to the OFF position 8 Position the Power Module at the chassis slot as shown in Figure 10 SS Chassis Figure 10 Power ON OFF Switch 9 Slide the Power Module complete into the slot 11 Insert the two screws to secure the Power Module to the chassis 12 Plug the AC power cord into the AC receptacle on the Power Module 13 Plug the other end of the cord into an external AC power source 14 Push the power ON OFF switch to the ON position The power ON LED should be lit and the fans will be operational techsupport transition com Click the Transition Now link for a live Web chat I IONPS A AC Power Module Maintenance Continued Replacing the fuse CAUTION Ensure that the IONPS A AC Power Module has been disconnected from the external power source and the ON OFF switch is at 0 Failure to observe this caution could result in damage or failure of the Power Module To replace the fuse in the IONPS A AC Power Module 1 Ensure the ON OFF switch on the Power Module is in the OFF position 2 Disconnect the AC power cord from the external power source 3 Insert a small flat blade screwdriver into the groove on the front inside edge of the fuse holder as shown
7. g Hardware 3 Remove the slot cover from the right chassis slot and keep the two screws See Figure 4 Figure 4 Chassis Slot Cover techsupport transition com Click the Transition Now link for a live Web chat IONPS A AC Power Module Installation Continued Installing an optional Power Module into the ION chassis continued 4 Position the Power Module at the chassis slot as shown in Figure 5 ge ge Figure 5 Power Module Installation 5 Side the Power Module completely into the chassis See Figure 6 Installed Optional Power Module Figure 6 Power Module Installation Note Once the optional Power Module is seated to the backplane of the chassis the fans will become operational Installation Continued Installing an optional Power Module into the ION chassis continued 6 Insert the two screws to mount the Power Module to the chassis Connecting the Power Module to external power To connect external power to the IONPS A AC Power Module do the following 1 Locate the power cord for the Power Module 2 Make sure that the Power Module ON OFF switch is in the OFF position See Figure 7 3 Plug the female end of the AC power cord into the AC power receptacle on the Power Module See Figure 7 4 Plug the male end of the AC power cord into the AC power source Turn the power ON OFF switch to the ON position See Figure 7 Note Once the power ON OFF switch is
8. in Figure 11A 4 Carefully pull the fuse holder from the Power Module See Figure 11B Power ON OFF Switch Place Small Flathead _ Screw Driver Here Figures 11 A amp B Replacing Fuse 4 Remove the fuse from the fuse holder 5 The replacement fuse MUST BE the same amperage and voltage rating 6 Insert the fuse into the holder 7 Slide the fuse holder fully into the Power Module 8 Connect the power cord to Power Module and to the external power 9 Push the power ON OFF switch to the ON position 12 Tech Support 1 800 260 1312 International 00 1 952 94 1 7600 24 hours Technical Specification For use with Transition Networks Model IONPS A AC Power Module Dimensions 8 3 x 8 4 x 2 7 211 mm x 211 mm x 69 mm Weight 4 lb 6 35 kg approximately Power Input 100 240 V 47 63Hz 2 35 1 1 Amp typical with a fully loaded chassis Voltage Tolerance 10 Low Line Input Current 3 5A max Inrush Current 13A max peak starting current high line Transient Recovery Time lms max Power Output 12VDC at 16 67 Amp max Power Factor gt 0 6 0 95 10 to 100 load respectively Fuse 6 3 Amp 250 Volts MTBF Greater than 25 000 hours MIL HDBK 217F Greater than 68 750 hours Bellcore7 V5 0 Environment Operating temperature 0 to 50 C 32 to 72217 Storage temperature 25 to 70 C 13 to 158 F Humidity 5 to 90 non condensing Warranty Lifetime techsupport transition
9. l at www transition com under Products Installation IMPORTANT e All installation and service must be performed by qualified personnel only e Read understand and follow all CAUTION and WARNING notices instructions marked on the product including in this manual The IONPS A AC Power Module can replace an existing IONPS A AC Power Module or it can be installed as the redundant Power Module in an AC powered ION219 A chassis CAUTION While installing or servicing the Power Module wear a grounding device and observe all electrostatic discharge precautions Failure to observe this caution could result in damage or failure of the Power Module Power module redundancy The IONPS A AC Power Module includes Instant Fail Over IFO circuitry that provides the capability for the primary Power Module to power the chassis backplane while the auxiliary Power Module is in hot standby mode If the IFO circuitry detects the loss of primary power the auxiliary Power Module instantly provides power to the chassis backplane When primary power is restored the IFO circuitry places the auxiliary Power Module in hot standby mode The chassis primary Power Module is located in the left slot of the chassis as viewed from the rear The chassis auxiliary Power Module is located in the right slot of the chassis as viewed from the rear A single Power Module placed in either location can power the chassis backplane Note The IONPS A AC Powe
10. r Modules DO NOT load share 4 Tech Support 1 800 260 1312 International 00 1 952 941 7600 24 hours techsupport transition com Click the Transition Now link for a live Web chat 5 IONPS A AC Power Module Installation Continued Installing an optional Power Module into the ION chassis Z WARNING Do not connect the Power Module to an external power source before installing it into the chassis Failure to observe this warning could result in an electrical shock Note The Power Module is hot swappable i e swapped while the chassis is in operation provided the ON OFF switch of the Power Module is in the OFF position and it has been disconnected from its external power source To install the Power Module in the ION chassis do the following Note The procedure is the same for installing the Power Module into either slot 1 Push the Power Module ON OFF switch to the OFF position See Figure 2 Power Module Switch OFF Position Figure 2 Power ON OFF Switch 6 Tech Support 1 800 260 1312 International 00 1 952 941 7600 24 hours Installation Continued Installing an optional Power Module into the ION chassis continued If necessary remove the grounding hardware from the chassis before installing or 2 removing the Power Module See Figure 3 Chassis Grounding Kepsnuts S provided K AN D Compression Lugs Not Provided Figure 3 Chassis Groundin
11. re designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at the user s own expense Canadian Regulations This digital apparatus does not exceed the Class A limits for radio noise for digital apparatus set out on the radio interference regulations of the Canadian Department of Communications Le pr sent appareil num rique n met pas de bruits radio lectriques d passant les limites applicables aux appareils num riques de la Class A prescrites dans le R glement sur le brouillage radio lectrique dict par le minist re des Communications du Canada Trademark Notice All trademarks and registered trademarks are the property of their respective owners Copyright Restrictions 2009 2010 Transition Networks All rights reserved No part of this work may be reproduced or used in any form or by any means graphic electronic or mechanical without written permission from Transition Networks Printed in the U S A
12. rning could result in an electrical shock even death 2 Tech Support 1 800 260 1312 International 00 1 952 941 7600 24 hours techsupport transition com Click the Transition Now link for a live Web chat 3 IONPS A AC Power Module Description Transition Networks IONPS A AC Power Module can deliver power or provide optional redundant AC power to an ION219 A chassis See the ION219 A chassis manual 33421 You can download the manual www transition com then click on Product Product Finder Power Module component identification See Figure 1 Fans two fans exhaust warm air from the IONPS A AC Power Module Power LED ON green when powered up ON OFF switch when in the ON position power is supplied to the ION chassis Fuse inline AC Handle AC Power Receptacle for an AC power plug NYDN fF WN Dry Contact Relay optional Note The IONPS A AC Power Module has instant failover capability Figure 1 Power Module Components Description continued Notices The IONPS A AC Power Module must be installed by qualified technical personnel only Transition networks assumes no responsibility for the improper installation set up or use of the IONPS A AC Power Module e The information in this user s guide is subject to change For the most up to date information see the user s guide on line to download the current version of the manua
Download Pdf Manuals
Related Search