Toshiba W-707 VCR User Manual
Contents
1. Batteries AAA 120 V AC 60 Hz 19W 430 x 96 5 x 281 mm W H D 3 8 kg VHF Channels 2 13 UHF Channels 14 69 CATV Channels 1 125 UHF VHF 75 Q F type connector Standard NTSC Recording VHS format SP SLP Playback VHS format SP LP SLP Video cassette with YHS mark SLP 11 1 mm s SP 33 4 mm s SLP 480 minutes SP 160 minutes When T 160 video cassette is used Within approx 80 s When T 120 video cassette is used Within approx 54 s when T 120 video cassette is used 1 V p p 75 Q unbalanced negative sync pin jack 1 V p p 75 Q unbalanced negative sync pin jack Line input 308 mV rms more than 47 kQ pin jack Line output 308 mV rms less than 4 7 kO pin jack 20 Hz 20 kHz 90 dB Temperature 5 C to 40 C Humidity less than RH 8096 Designs and specifications are subject to change without notice LIMITED WARRANTY TOSHIBA VIDEO CASSETTE RECORDER Toshiba America Consumer Products Inc TACP and Toshiba Hawaii Inc THP make the following limited warranties These limited warranties extend to the original consumer purchaser or any person receiving this set as a gift from the original consumer purchaser and to no other purchaser or transferee Limited Ninety 90 Day Warranty TACP THI warrant this product against defects in materials or workmanship for a period of ninety days after the dat2. e j e END GD After about 30 seconds the screen disappears Changing cancelling the timer programs 1 If the TIMER indicator is lit press both TIMER to turn it off and then turn the VCR on by pressing VCR POWER 2 With steps 2 to 9 change the items To cancel a program select the program you want to cancel in step 4 and press CANCEL The line is then cleared 3 Press both TIMER to return to the timer standby mode Recording or playback in the timer standby mode First press both TIMER to release the timer standby mode and then press VCR POWER to turn on the VCR The VCR will be available for use Be sure to press both TIMER again to return the VCR to the timer standby mode after you are finished Error indication The E Error indicator appears in the VCR display if you press both TIMER when a cassette is not loaded the loaded cassette has no safety tab no timer program is set In these cases a recording can not be made 28 If a power failure occurs during the timer program recording including VCR Plus C system recording page 31 When a power failure has occurred appears in the VCR display Since the programmed contents have been cleared reset the clock and timer programming When power has failed for a short time the colon of the current time display blinks The programmed contents are not affec
3. NOILVHVdHHd i Warning Do not insert your hands or any foreign objects into the compartment This may result in injury or damage Take special care with children to avoid accidents Precautions when using video cassettes Video cassettes have a safety tab to prevent accidental erasure If the tab has already been removed recording cannot be performed To prevent accidental erasure To record again Remove this safety tab with a screwdriver Cover the tab hole with adhesive tape Avoid exposing cassettes to direct sunlight Keep them away from heaters Avoid extreme humidity vibrations or shock strong magnetic fields near a motor transformer or magnet and dusty place 19 PLAYBACK Playback This section explains the basic playback operation Preparation Select the video channel 3 or 4 or video input mode on the TV Press VCH to set the remote control operating the VCR VCR CH TRK Adjusting the tracking When playback starts the VCR automatically adjusts the tracking for clear pictures and sound Digital Auto Tracking The DT indicator blinks during the adjusting If the VCR cannot locate the best possible tracking point hold down one of CH TRK to adjust the tracking manually To resume the digital auto tracking hold down both CHANNEL on the VCR simultaneously for about 2 seconds Notes During the adjusting the playback picture and soun
4. 10 Select see below To set another program press CURSOR RIGHT and select the next line pressing CURSOR DOWN Repeat steps 4 to 8 Press PROG Now programming is completed Press both TIMER simultaneously a A The power turns off and the VCR enters POWER Gc the timer standby mode ate TIMER i j L 2 Auto Speed Select If you are not sure the tape is long enough for timer program recording in the SP tape speed set the recording tape speed to AUTO Recording starts in the SP tape speed and the VCR automatically selects the tape speed to record the program to the end If the tape length is not long enough the tape speed automatically changes from SP to SLP Notes Make sure that the tape length is selected correctly according to the tape used on the SET UP screen page 23 When the SLP tape speed is selected and the tape length is not sufficient to record the program to the end the program cannot be recorded to the end The picture will be distorted when playing the part where the recording tape speed is switched from SP to SLP with the Auto Speed Select feature DNIQHOO3H 27 Confirming the timer programs in the timer standby mode Press PROG The screen for confirming will appear program DI sET UP PRESET CH DATE On OFF SPD e 25 8 30 9 30 10 00P45P_ e j e e
5. During the timer standby mode TIMER indicator lit Press PROG The screen for confirming appears After about 30 seconds the screen disappears Canceling the VCR Plus C e system timer programs 1 If the TIMER indicator is lit press both TIMER to turn it off and turn on the VCR by pressing VCR POWER 2 Press PROG to display the MENU screen 3 Press ENTER to select PROGRAM 4 Select a program which you want to cancel 5 Press CANCEL The line is cleared out 6 Press PROG to exit First press both TIMEH to release the timer standby mode and then press VCR POWER to turn on the VCR The VCR will be available for use Be sure to press both TIMER again to return the VCR to the timer standby mode after you have finished Error indications If FULL CANCEL PROG message appears on the TV during programming no more programs can be entered If you want to add another delete one existing program on the screen by using CURSOR UP or CURSOR DOWN If an incorrect PlusCode programming number is entered ERROR CODE ENTERED appears on the screen Press CANCEL to clear the number and enter correct one If CLASH message appears on the TV during programming it tells you that two programs with the same recording start time have been entered Correct either of the two programs as follows 1 Select the number of the program to correct by using CURSOR UP or CURSOR DOWN 2 Correct the data
6. LEFT or CURSOR RIGHT como FOR FRA Ger END 2 Press PROG to exit 3 Select the desired channel using CHANNEL on the VCR or CH TRK on the remote control If you use a cable box select a desired channel on the box Select the recording tape speed using SP SLP Press REC to start recording OU A Press STOP to stop recording 41 ADDITIONAL INFORMATION Multi Brand Remote Control The remote control can be compatible with various brands of TV by setting their control codes The TOSHIBA code has initially been set to control TOSHIBA TVs Setting Control Codes 1 D ry POWER 1 Press TVto set the remote control operating your TV ae 2 While holding down PROG enter the ja down Exainbie l Depay two digits of your TV s brand code Go x I Number listed right using number buttons 0 2 buttons H CH TRK 3 Release PROG i TV VOL I 100 4 Point the remote control at your TV and use each button listed below to make sure that your TV is operated correctly ENTER TVPOWER Toturnthe TV on or off Zs 3 CH TRK To select TV channels in the upper or lower direction TV VOL To adjust the sound level INPUT SELECT To select an external source such as a VCR Number buttons To select TV channels When selecting channels 1 to 9 first enter 0 and then the desired number 100 To substitute for 100 channel key DISPLAY To turn on or off TV s screen display ENTEH To use for the TV s ENTER k
7. Select the video channel 3 or 4 or video input mode on the TV Set TV CATV on the CH MEMORY screen to CATV page 17 Number buttons INPUT SELECT 100 SP SLP CURSOR LEFT CURSOR UP ENTER CURSOR RIGHT PROG CURSOR DOWN POWER CABLE BOX CH CABLE BOX 1 2 3 4 Cable Box Set up Press PROG to display the MENU screen Select PRESET using CURSOR RIGHT or CURSOR LEFT and press ENTER Select CABLE BOX DSS using CURSOR UP or CURSOR DOWN and press ENTER Select NO or C BOX using CURSOR RIGHT or CURSOR LEFT according to your connection type NO Type A Type C A B switch A Cable channels will be selected using CH TRK on the remote control or CHANNEL on the VCR Go to step 8 C BOX Type B Type C A B switch B Type D Go to step 5 Select OUTPUT CH using CURSOR UP or CURSOR DOWN and enter either of the following according to your connection Type B C the output channel number of your cable box using number buttons Usually 3 or 4 Check the rear of the procram DIE ser up preser TIENS lO C BOX DSS procrau EIE ser up Ed preset A NO CHBOX DSS 3 CH OFF on Example procraul EB ser up preser cable box OUTPUT CH ibd cH Type D the line input mode L1 using OFE con INPUT SELECT Select CONTROL using CURS
8. preser the own channel selector of the DSS TIN NO C BOX DSS satellite receiver 3 CH CONTROL OFF on The VCR channel should be set to the output channel of the DSS satellite receiver ED ED gt Go to step 8 7 Select BRAND TYPE using CURSOR DOWN and enter a brand code of your DSS satellite receiver using number buttons Refer to the table on the next page Example For a TOSHIBA DSS satellite receiver identified by number 99 C Prospan EIE ser up E preser VCR display NO C BOX DSS 3 CH C OFF on no 99 USE OUTPUT CH END GD Make sure that the background of the above display has changed to the satellite program on channel 200 If not relocate the DSS satellite receiver on the VCR so that it can receive the infrared signal Press PROG to exit Notes f your satellite channel does not change to 200 in step 7 the DSS satetllite receiver will not be able to change channels in the timer recording In this case set CONTROL to OFF in step 6 The VCR Plus C e system recording is not available on satellite channels The DSS satellite receiver control is not compatible with the cable box control Buttons to control a remote Table of DSS satellite receiver brand controllable DSS satellite receiver codes Once you complete the set up for a remote controllable DSS satellite receiver your DSS Brand name of your satellite receiver can be con
9. 61 Videoway 7 23 45 50 84 Diamond 1 20 21 29 42 44 63 Viewstar 88 91 26 58 62 84 Eagle 13 20 21 22 23 24 25 Warner Amex 26 58 62 84 Zenith 7 23 45 50 84 Eastern 26 28 GC Brand Gemini 4 30 85 General Instrument 1 2 3 4 31 34 55 85 91 Hamlin 14 15 28 41 Jerrold 1 2 8 4 31 34 55 85 91 Macom 31 79 80 Magnavox 13 20 21 22 23 24 25 26 58 62 84 Movietime 29 32 38 39 42 44 88 NSC OAK OAK Sigma 10 11 12 13 46 Philips 4 13 20 21 22 23 24 25 26 58 62 84 Pioneer 5 6 78 Pulsar 26 58 62 84 RCA Realistic 44 88 Regal 14 23 41 84 Regency 26 28 Rembrandt Samsung 4 6 32 42 78 Scientific Atlanta 8 9 56 61 Sheritech 27 SL Mark Sprucher 6 8 16 17 Stargate 4 6 30 32 42 44 52 63 78 88 Sylvania Teknika 91 RECORDING DSS Satellite Receiver Set up The VCR can directly control channel selecting of the connected DSS satellite receiver DSS Satellite Receiver Control Connection Type This VCR needs to be connected to a DSS Type A satellite receiver equipped with an infrared wireless remote control You can select Satellite antenna satellite channels from the DSS satellite receiver by operating this VCR DSS is registered trademark of DIRECT V Inc a unit of GM Hughes Electronics It is also possible to automatically change the satellite channels according to your progr
10. VCR 2 Press PROG VCR The following screen appears on the TV VCR POWER NOILVHVdHHd i UE ser up I preset ENGLISH FRANCAIS ESPANOL PROG ENTER p amp Select the language using CURSOR RIGHT UP or CURSOR DOWN and press MENU CURSOR UP PROG AR The screen turns to the MENU screen DI set up PRESET CURSOR LEFT aD 4 Press PROG to return to the normal TV screen Optional settings on the SET UP screen Other optional settings can be made Press ENTER while SET UP is selected on the MENU screen The screen turns to the SET UP screen Page 23 po SES Page 40 120 160 180 on Page 41 on AUTO With AUTO set a TV broadcast will appear via the TV tuner after playback EnD GD Move down here and set to AUTO or MANU If you made the Audio Video connection page 11 set to MANU 7 procew EIE ser up LS preser ENG FRA ESP LOS ON OFF To change the language move down here and set to the desired one With ON set you can see the station ID and program title displayed on TV To exit press PROG Continued 15 16 Initial Settings Using On Screen Display continued Setting the Clock Example To set the clock to 2 30 p m on August 25 summer time 2000 Press PROG The MENU screen appears on the TV Select PRESET using CURSOR RIGHT or CURSOR LEFT and p
11. each of digits from 1 to 91 Press PROG to exit DONIQHOO3H i Notes If your cable channel does not change to 9 in step 7 the cable box will not be able to change channels in the timer recording In this case set CONTROL to OFF in step 6 The cable box control is not compatible with the DSS satellite receiver control Buttons to control a remote controllable cable box Once you complete the set up for a remote controllable cable box your cable box can be controlled by the following buttons on the remote control of the VCR POWER CABLE BOX To turn the cable box on or off CH CABLE BOX To select cable channels in the upper or lower direction not applicable to some brands of cable box Number buttons 0 9 To select desired channels to record 100 Some cable boxes require you to use this button as the enter button Press this button after selecting the cable channel with number buttons 35 Cable Box Set up continued Table of cable box brand codes 36 EE of your mee of your Brand code Toshiba Telecaption 77 Anvision 13 20 21 22 23 24 25 Teleview 4 6 32 42 78 Archer 1 20 21 29 42 44 63 Tocom n Cablestar 13 20 21 22 23 24 25 Unika 1 20 21 29 42 44 63 26 58 62 84 88 91 Cableview 30 42 44 52 63 88 Universal 29 42 43 44 52 63 82 Citizen 88 Curtis 8 9 56
12. the remote control Be careful not to spill water on the remote control or to place it on anything wet and avoid sharp impacts PREPARATION Connections Before you use this VCR it is necessary to connect it to your TV Several ways of connecting are available depending on your use of TV or cable box Select one which is applicable to your equipment Antenna VCR TV Connection 1 Disconnect the antenna cable from your TV and connect it to the RF IN terminal on the VCR 2 Connect the RF OUT terminal to the TV VHF UHF combinaion VHF antenna UHF antenna antenna only only 1 o o ORN DEN 2 SUCH VHF UHF T 4 Oi com gt Setting the VCR Output Channel When the VCR is connected in this way the VCR sends the output Antenna splitter signals to channel 3 or 4 on your TV Set the output channel not supplied selector CH selector of the VCR to 3 or 4 whichever is vacant in your area AUDIO VIDEO Connections The AUDIO VIDEO jacks are also available to connect your TV When connected your TV using the AUDIO VIDEO OUT jacks To watch video pictures set the video input mode on your TV For the video input mode refer to the manual of your TV LINE OUT VIDEO VIDEO IN ADA Pipe aci LINE OUT AUDIO AUDIO IN NOILVHVdHHd i Connections continued Cable Connection Choose one of the below according to your usage of the cable box
13. CR scans through all receivable TV and CATV channels and stores only the active ones in your area into the memory Once the storing is finished you can select a desired channel using CH Preparation Turn on the TV and select the video channel 3 or 4 or the video input mode if you made the Audio Video connection page 11 NOILVHVddHHUd i Press INPUT SELECT so that the channel number will appear if L1 or L2 is displayed in the VCR display Incoming Antenna Cable CATV Signals 1 INPUT 2 SELECT Number buttons 100 1 6 ENTER 3 CURSOR RIGHT CURSOR UP CURSOR DOWN CURSOR LEFT 6 Press PROG to display the MENU screen Select PRESET using CURSOR RIGHT or CURSOR LEFT and press ENTER procraul 0 ser up E preser CLOCK SET CH MEMORY CABLE BOX DSS GUIDE CH EnD CO Select CH MEMORY using o CURSOR UP or CURSOR DOWN AAN aS and press ENTER TV CATV H AUTO SCAN EnD Gi Set TV CATV to TV or CATV using CURSOR RIGHT or CURSOR LEFT TV To store channels received via the antenna CATV To store channels received via the incoming cable Select AUTO SCAN using CURSOR UP or CURSOR DOWN proca OB ser uel E preser and press CURSOR RIGHT to set to On The VCR starts scanning and the channels are stored in the VCR in ascending order When the scanning is finished the screen automati
14. E YEAR 9 5791 01 00 SA END GD eu Select the options using CURSOR RIGHT or CURSOR LEFT Change the data using CURSOR UP or CURSOR DOWN 1 Set SUMMER TIME Daylight Saving Time IN daylight saving time begins on the first Sunday in April Because the clock automatically changes from 2 00 AM to 3 00 AM forward one hour remember that any part of a scheduled Timer Recording that falls between these two times will not be recorded OUT daylight saving time ends on the last Sunday in October The VCR clock automatically changes from 2 00 AM to 1 00 AM back one hour Therefore it can affect your recording length if one is set for this time 2 Set Time Zone If you select AUTO for your time zone the VCR sets the clock using the first Coordinated Universal Time information it finds If the time is not correct select another time zone or use the MANU option 3 Set CH If you don t know the clock data channel select AUTO The VCR will scan automatically to tune the channel carrying the clock data If AUTO CLOCK SET is unsuccessful set the time and date through the MANU clock set menu selection Press PROG Now the clock starts 1 Press PROG to exit PREPARATION Storing Channels on the VCR This section is required if you receive only normal TV or unscrambled cable channels or use a cable box between your TV and the VCR Incoming Antenna Cable CATV Signals The V
15. FPA 70 provides information with regard to proper grounding of the mast and supporting structure grounding of the lead in wire to an antenna discharge unit size of grounding conductors location of antenna discharge unit connection to grounding electrodes and requirements for the grounding electrode EXAMPLE OF ANTENNA GROUNDING AS PER NATIONAL ELECTRICAL CODE ANTENNA LEAD IN WIRE GROUND ANTENNA DISCHARGE UNIT ELECTRIC NEC SECTION 810 20 SERVICE EQUIPMENT a GROUNDING CONDUCTORS NEC SECTION 810 21 GROUND CLAMPS POWER SERVICE GROUNDING ELECTRODE SYSTEM NEC ART 250 PART H NEC NATIONAL ELECTRICAL CODE S2898A Power Lines An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits or where it can fall into such power lines or circuits When installing an outside antenna system extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal IMPORTANT SAFETY INSTRUCTIONS 12 13 14 15 16 17 18 19 Lightning For added protection for this product during storm or when it is left unattended and unused for long periods of time unplug it from the wall outlet and disconnect the antenna or cable system This will prevent damage to the product due to lightning and power line surges Object and Liquid Entry Never push objects of any kind into t
16. ITED WARRANTY 47 NOILONGOULNI a INTRODUCTION Identification of Controls See the page in for details This manual shows the names of buttons in italics Front Panel CHANNEL 25 EJECT PLAY POWER 15 Cassette compartment STOP TOSHIBA oN SACP SHUTTLE 22 LINE IN2 e 9O VIDEO jack EZ d PAUSE STILL LINE IN 2 AUDIO Peer Jor SE 21 L MONO R jacks REC 25 VCR display 9 Remote Control VCR POWER 15 TV POWER To operate this VCR VCR DISPLAY 23 INPUT SELECT 25 COUNT RESET 23 EJECT To operate your TV TV REMAIN COUNTER 23 Number buttons 25 A SELECT 40 TV VCR SP SLP 25 CH TRK E 100 TV VOL 35 REW 20 PLAY 20 sLow 21 id PAUSE STILL 21 ps TIMER VCR Plus 31 CURSOR UP 15 PROG 15 ENTER 15 19u 20 CURSOR RIGHT CANCEL CURSOR DOWN 15 INDEX CURSOR LEFT POWER CABLE BOX 35 CH CABLE BOX 35 SHUTTLE dial 22 JOG dial 22 VCR Display VCR indicator Timer recording indicator REMAIN indicator Cassette indicator POWER indicator NOILONGOULNI a OFF indicator Hi Fi L R indicators L Left channel R Right channel off Normal track REC Recordin Multifunctional indicator r ee Reel ng DT Digital Auto Tracking indicator Tape speed indicator snannel maigatgr a SP SLP Tape running direction speed indicato
17. If a number 1 to 99 is entered the VCR will record a TV CATV program on the channel not a satellite s If your DSS satellite receiver is not remote controllable choose the desired channel 100 to 999 on the DSS satellite receiver To make corrections Press CURSOR LEFT to move back to the item or CURSOR RIGHT to forward 5 Move to the next using CURSOR RIGHT and set the recording date using CURSOR UP or CURSOR DOWN The date changes as follows 7 procera FB set up E preser CH DATE on OFF SFD e 25 8 30 e e j PPM ERN eim e END Gi gt 8 25 gt 8 26 gt gt 9 24 2 WKLYSU gt 4 prom MO FR WKLYSA WKLYSU WKLYSA You can record TV programs on the same channel on the day and time every week MO FR You can record TV programs on the same channel on the day and time Monday through Friday Move to the next using CURSOR RIGHT and set the hour and minutes of the recording start time PROGRAM CH DATE On OFF SPD pein jalan ait AD ser up PRESET Move to the next and set the recording off time R UD ser CH DATE on OFF SPD e 25 8 30 9 S0y n OOPISLE Move to the next and select the tape speed SP using CURSOR UP or CURSOR DOWN tM n i For the tape speed AUTO Auto Speed
18. OR UP or CURSOR DOWN and set to ON or OFF using CURSOR RIGHT or CURSOR LEFT ON if your cable box is remote controllable Cable channels will be selected by CH CABLE BOX on the remote control The VCR can change the cable channel to the desired one when timer recording or VCR Plus C system recording starts Go to step 7 OFF if your cable box is NON remote controllable Cable channels will be selected by the own channel selector of the cable box The VCR channel should be set to the output channel of the cable box Go to step 8 CD procrau EI ser up E preser M NO C BOX DSS 3 CH Council OFF NOD no 1 EnD Gi C procrau EI set up E preser M NO C BOX DSS 3 CH CONTROL OFF on EnD 7 Select BRAND TYPE using CURSOR DOWN and enter a brand code of your cable box using number buttons Refer to the table on the next page Example For a TOSHIBA cable box identified by number 36 C proce BIB ser up preser Cable box display VCR display THEN NO C BOX DSS a 3 CH OFF on m BRAND TYPE no 36 pM ix ED Cablechannel number Make sure that the channel display of your cable box has changed to 9 If not try each brand code assigned to the brand of your cable box until the display changes to 9 If it still holds Relocate the cable box on the VCR Use
19. SOR 3 Select CABLE BOX DSS using ROGRAM Lj ETE CURSOR UP or CURSOR DOWN Ces m ser uel raser CURSOR and press ENTER TS 10 C BOX DSS RIGHT PROG CURSOR DOWN CH CABLEBOX 4 Select DSS using CURSOR PA RIGHT CABLE BOX procraul EB ser up E preser 3 CH OFF on EnD Gi 5S Select OUTPUT CH using CURSOR UP or CURSOR DOWN and enter either of the following according to your connection Example Type A the output channel number of O Procranl EY ser up E preser your DSS satellite receiver using number buttons Usually 3 or 4 Check no C BOX DSS CH 3 the rear of the DSS satellite receiver e OFF on Type B the line input mode L1 using EE TO SET CH INPUT SELECT 0 9 KEYS NN Select CONTROL using CURSOR UP or CURSOR DOWN and set to ON or OFF using CURSOR RIGHT or CURSOR LEFT ON if your DSS satellite receiver is remote controllable Satellite channels will be selected by DEIN NO C BOX DSS CH CABLE BOX on the remote 3 CH procea GH ser up E preser E OFF On control no 1 The VCR can change the satellite channel to the desired one when timer END D recording starts Go to step 7 OFF if your DSS satellite receiver is NON remote controllable M Satellite channels will be selected by Proce E ser up
20. States contact In Hawaii contact Toshiba Hawaii 327 Kamakee Street Honolulu HA 96814 808 591 8377 Toll Free 800 631 3811 S A All warranties implied by state law including the implied warranties of merchantability and fitness for a particular purpose are expressly limited to the duration of the limited warranties set forth above With the exception of any warranties implied by state law as hereby limited the foregoing warranty is exclusive and in lieu of all other warranties guarantees agreements and similar obligations of manufacturer or seller with respect to the repair or replacement of any parts In no event shall TACP THI be liable for consequential or incidental damages No person agent distributor dealer or company is authorized to change modify or extend the terms of these warranties in any manner whatsoever The time within action must be commenced to enforce any obligation of TACP THI arising under the warranty or under any statute or law of the United States or any state thereof is hereby limited to ninety 90 days from the date you discover or should have discovered the defect This limitation does not apply to implied warranties arising under state law This warranty gives you specific legal rights and you may also have other rights which may vary from state to state Some states do not allow limitation on how long an implied warranty lasts when an action may be brought or the exclusion or limitation of inc
21. TOSHIBA Hi Fi Video Cassette Recorder W 707 OW NER S MANUAL verft SOPB ABLE BOX ONTROL This publication is printed on recycled paper 70971855 SAFETY PRECAUTIONS The lightning flash with arrowhead sym CAUTION bol within an equilateral triangle is q g RISK OF ELECTRIC SHOCK s DO NOT OPEN intended to alert the user to the presence of uninsulated dangerous voltage within XU REE ean E TE the product s enclosure that may be of AUTION un ELECTRIC SHOCK DO NOT REMOVE sufficient magnitude to constitute a risk of COVER OR BACK NO USERSERVICEABLE electric shock to persons PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The exclamation point within an equilat eral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the appliance WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE DANGEROUS HIGH VOLTAGES ARE PRESENT INSIDE THE ENCLOSURE DO NOT OPEN THE CABINET REFER SERVICING TO QUALIFIED PERSONNEL ONLY CAUTION TO PREVENT ELECTRIC SHOCK MATCH WIDE BLADE OF PLUG TO WIDE SLOT FULLY INSERT Product Name Video Cassette Recorder Model Number W 707 FCC Notice Declaration of Conformity This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not c
22. The desired sound is not heard such as SAP stereo or regular sound Setting of sounds is not correct Select a desired sound using A SELECT page 40 Noise is present in the Hi Fi sound being played Tracking is not set appropriately Adjust the tracking manually page 20 The timer recording function does not work There is an error in programming Reset the timer recording program page 26 There is no cassette in the VCR Load a cassette with the safety tab attached page 19 The cassette does not have the safety tab Use another cassette with a safety tab or cover the hole with adhesive tape page 19 The timer indicator is not displayed Press both TIMER simultaneously page 27 There has been a power failure Reset the clock page 16 The cable box set up has not been set correctly Make the set up correctly page 34 The cable box is not turned on Turn on the cable box The VCR Plus C system recording cannot be done The guide channel numbers are not set up correctly Make the guide channel number setting page 29 The cable box is not turned on when the channel comes in the VCR via the cable box Turn on the cable box The cable box set up has not been set correctly Make the set up correctly page 34 The timer indicator is not displayed Press both TIMER simultaneously page 32 The remote control does
23. This set up will enable you to record an unscrambled channel watch an unscrambled channel while recording it record an unscrambled channel while watching another only when you connect a cable compatible TV Incoming cable You will need to select TV channel 3 or 4 to receive video signals See page 11 to record a channel while watching another press TV VCR on the remote control to turn off the VCR indicator in the VCR display and select a desired channel on the TV only when you connect a cable compatible TV This set up will enable you to record an unscrambled channel E watch an unscrambled channel while recording it record an unscrambled channel while watching Cable Box another scrambled or unscrambled Incoming cable You will need to set TV channel to the output channel of the cable box turn on the cable box and select cable channel 3 or 4 according to the output channel of the VCR torecord a channel while watching another press TV VCR on the remote control to turn off the VCR indicator in the VCR display and select a desired cable channel on the cable box 12 Cable Box j NG OUT A B switch lt aq POD ze Cable Box gt LJ This set up will enable you to watch an unscrambled o
24. am setting in the timer program recording DNIQHOO3H i Placing the DSS Satellite Receiver Type B Put the DSS satellite receiver on the top of the VCR as shown below Do not block the Satellite sensor window antenna Incoming cable A DSS satellite receiver DSS satellite receiver L Front of the VCR SS SENSN SN 2 Sensor window The infrared signals come out of the sensor window and the front of the VCR Then they bounce off walls and other objects in the room and are received by the DSS satellite receiver The VCR sends out infrared signals to your DSS satellite receiver even during timer program recording Notes If the channels cannot be controlled properly because the infrared signal fails to reach the DSS satellite receiver change the position of the receiver on the VCR so that it can receive the signal Keep the DSS satellite receiver turned on even while the VCR is in the timer program recording 37 38 DSS Satellite Receiver Set up continued Preparation Select the video channel 3 or 4 or video input mode on the TV DSS Satellite Receiver Set up 1 Press PROG to display the MENU screen INPUT 2 Select PRESET using CURSOR E IW ser up PRESET SELECT RIGHT or CURSOR LEFT and Buona press ENTER CLOCK SET CH MEMORY CABLE BOX DSS SP SLP GUIDE CH CURSOR inp GD LEFT a CUR
25. and Channel 4 4 WTTV PlusCode are registered trademarks of Channel 5 6 WRTV Gemstar Development Corporation The VCR Channel 6 VCA Local origination Plus system is manufactured under license Channel 7 HOME BOX OFFICE from Gemstar Development Corporation Channel 8 A P News Plus Channel 9 9 WGN You must give the VCR the special numbers for guide channels also called VCR Plus system channel numbers assigned to each channel that you receive in your home The VCR identifies the channel to be recorded by the guide channel number you enter The guide channel numbers are published in TV guide magazine selected local TV publications or the channel guide from cable company If you cannot find the numbers call Gemstar s customer service department at 1 800 4321 VCR DONIQHOO3H i 29 30 VCR Plus C System Set up Continued Preparation Select the video channel 3 or 4 or video input mode on the TV If you record cable channels finish the cable box set up pages 33 36 Prepare the list like below Example Your home channel number on the channel line up on the TV Guide local TV listings etc chart supplied by cable companies km Rises eee 7 esn o 89 y Notes When your cable company changes the channel line up you must re do this set up for the channel The VCR Plus C e System feature does not work on programs from a connected DSS satellite receiver Guide Ch
26. annel Setting 1 2 3 An A Press PROG Select PRESET using CURSOR RIGHT or CURSOR LEFT and press ENTER Select CH MEMORY using CURSOR UP or CURSOR DOWN and press ENTER Set TV CATV to TV or CATV using CURSOR RIGHT or CURSOR LEFT Press PROG to return to the PRESET screen Select GUIDE CH using CURSOR UP or CURSOR DOWN and press ENTER 1 2 3 the case of CATV mode GUIDE CH v HO TO SET CH PUSH 0 9 KEYS EnD CO Enter channel numbers on the right of the guide channel numbers Find a guide number you marked on the list using CURSOR UP or CURSOR DOWN and enter the corresponding home channel number if necessary by using number buttons Example To enter home channel number 7 HBO with guide channel number 33 assigned proceau m ser up In some areas one channel may be assigned more than one guide channel number In this case enter the home TO SET CH PUSH 0 9 KEYS EnD CXD channel number to each of the guide channel numbers Press PROG to exit The set up is all over and your VCR Plus C system recording is now available RECORDING VCR Plus C e system Recording After performing the z system set up you can easily program a recording simply by entering the PlusCode programming number The numbers are published in the TV listings of newspapers TV guide magaz
27. ause harmful interference and 2 this device must accept any interference received including interference that may Cause undesired operation Contact Toshiba America Consumer Products Inc Address 1420 Toshiba Drive Lebanon TN37087 Telephone 615 449 2360 User Installer Caution Changes or modification made to this equipment not expressly approved by Toshiba Corporation or parties authorized by Toshiba Corporation could void the user s authority to operate the equipment Note to CATV system installer This reminder is provided to call the CATV system installer s attention to Article 820 40 of the NEC that provides guidelines for proper grounding and in particular specifies that the cable ground shall be connected to the grounding system of the building as close to the point of cable entry as practical IMPORTANT PRECAUTIONS Save Original Packing Materials The original shipping carton and packing materials will come in handy if you ever have to ship your VCR For maximum protection repack the set as it was originally packed at the factory Avoid Volatile Liquid Do not use volatile liquids such as an insect spray near the unit Do not leave rubber or plastic products touching the unit for a long time They will mar the finish Moisture Condensation Never operate this unit immediately after moving it from a cold location to a warm location When the VCR is exposed to such a change in temperature mois
28. cally returns Press PROG to exit NOS 8 2CH ON 17 Storing Channels on the VCR continued Adding or erasing channels Adding channels If a desired channel cannot be scanned automatically because of a weak signal it can be added to the memory Erasing channels You can erase a stored channel from the memory if itis unnecessary 1 Follow steps 1 to 3 of Incoming Antenna CATV Signals 2 Select ADD CH or ERASE CH using CURSOR UP or CURSOR DOWN To add channels proce MD ser up E preset BN TO SET CH PUSH 0 9 KEYS EM EnD Gi TV OFF CATV To erase channels MD ser up E preset procera BN TO SET CH PUSH 0 9 KEYS MN EnD Gi TV CATV Channel reference chart 3 Enter a channel number of 1 to 125 using number buttons For more than 100 number first press 100 For CATV channels refer to the chart below For other orders check with your cable company 4 Repeat steps 2 and 3 to add or erase channels as necessary 5 Press PROG to exit Selecting stored channels Once the active channels have been stored you can select the channels in two ways below Number buttons To enter digits of the channel number For one digit number enter 0 before For more than 100 number first press 100 Each number button needs to be pressed within 2 seconds CH TRK To shift up or d
29. d may be distorted The digital auto tracking is activated only in the playback mode To reset the manual tracking point to the center press both CHANNEL on the VCR simultaneously for not longer than 1 second The noise on the screen may not be completely eliminated depending on the tape used especially when the tape was recorded on another VCR 20 Basic Playback 1 Load a recorded cassette H POWER OO Power is turned on If the cassette has no safety tab playback starts automatically 2 2 Press PLAY to start playback TES S P vcr FF DT Bus 3 To stop playback press STOP DNR Rewinding Fast forwarding Press REW or FF in the Stop mode 19 HEAD You can view high quality pictures while playing back a tape recorded in the SLP tape speed By pressing 19u repeatedly the 19u HEAD mode is displayed on the TV screen as follows 19U HEAD AUTO Usually set to AUTO As the playback starts the VCR automatically activates the 19u head and reproduces high quality pictures 19U HEAD OFF Set to OFF if the pictures are marred by dots Note During playback with the 19u head momentary noises or shakes may be produced when you change the mode to the picture search or variable speed playback PLAYBACK Variable Speed Playback You can play back a tape at various tape speeds PLAY x2 REW PAUSE STILL Note SLOW Press PLAY A picture freezes so tha
30. e of original retail purchase During this period TACP THI will repair a defective product or part without charge to you You must deliver the entire productto a TACP THI Authorized Service Station You areresponsible for all transportation and insurance charges for the set to and from the Authorized Service Station Limited One 1 Year Warranty TACP THI further warrant the parts in this product against defects in materials or workmanship for a period of one 1 year after the date of original retail purchase During this period TACP THI will replace a defective part without charge to you except that if a defective part is replaced after ninety 90 days from the date of the original retail purchase you pay labor charges involved in the replacement You must also deliver the entire productto a TACP THI Authorized Service Station You areresponsible for all transportation and insurance charges for the set to and from the Authorized Service Station Rental Units The warranty for rental units begin with the first rental or thirty 30 days from the date of shipment to the rental firm whichever comes first Commercial Units Products sold and used for commercial use have a limited ninety 90 day warranty for all parts and labor Owner s Manual and Demographic Card You should read the owner s manual thoroughly before operating this product You should complete and mail the enclosed Demographic card within ten 10 days after you or t
31. eck the following symptoms before requesting servicing No power The power cord is not plugged in Plug the power cord into the outlet firmly Although the power is on the VCR will not work There is no cassette Load a cassette page 19 The clock does not work There has been a power failure Reset the clock page 16 The timer does not work properly The time is incorrect Set the clock correctly page 16 The picture does not appear on the TV screen The video channel or video input mode is not set correctly Set the TV channel to the video channel 3 or 4 or set the video input mode on the TV page 11 The TV signal is weak Adjust the antenna direction or use an optional antenna booster The power cord is not plugged in Plug the power cord into the outlet firmly The picture does not appear on the TV screen during recording and playback The video channel or VCR mode is not set correctly Press TV VCH to select the VCR mode and set the TV channel to 3 or 4 pages 11 25 The VCR does not record The loaded cassette has no safety tab Use a cassette with a safety tab or cover the hole with adhesive tape page 19 The playback picture is poor Tracking is not set appropriately Adjust the tracking manually page 20 The video heads are dirty Clean the video heads with a commercially available cleaning tape
32. ey Important Some TVs may not respond to all the operations above or may not be operated at all with this remote control In this case operate your TV with its own remote control Notes For some brands several control codes brand codes are allocated Try each of them until the buttons work on your TV f you replace the remote control s batteries set the brand code again Table of Brand Codes Brand name of your TV Brand Code Brand name of your TV Brand Code Toshiba 01 Proton 11 Bell amp Howell 09 Pulser 14 Carver 10 Quasar 07 15 03 13 Curtis Mathes 09 12 Realistic 09 11 13 Dumont 14 Runco NEC 14 Electro band 03 Samsung 11 12 Emerson 09 11 Sanyo 09 09 d 02 07 11 1 Gibralter 14 Sears 01 02 09 10 11 Goldstar 11 Sharp 08 13 Hallmark 11 Sony 03 Hitachi 06 Soundesign 11 10 03 JCB 03 Tandy 08 JVC 05 Technics 07 15 LXI 01 02 09 10 11 Techwood 07 Magnavox 10 Teknika 04 10 12 06 11 05 Memorex 04 09 11 Vidikron 10 MGA 04 11 Vidtech 11 Midland 02 07 14 Wards 10 11 13 Mitsubishi 04 11 Zenith 14 08 2 NAD 01 11 Nikko 11 Optimus 09 Optonica 08 07 10 15 01 02 07 11 12 Philco 10 Philips 10 Pioneer 16 Princeclub 12 07 Proscan 02 NOILVINYOSNI TVNOILIGGV a 43 ADDITIONAL INFORMATION Before Calling Service Personnel Ch
33. he person who has given you this product as a gift purchased this product This is one way to enable TACP THI to provide you with better customer service and improved products Failure to return the card will not affect your rights under this warranty Your Responsibility The above warranties are subject to the following conditions 1 You must retain your bill of sale or provide other proof of purchase 2 You must notify an Authorized TACP THI Service Station within thirty 30 days after you discover a defective product or part 3 All warranty servicing of this product must be made by an Authorized TACP THI Service Station 4 These warranties are effective only if the product is purchased and operated in the U S A or Puerto Rico 5 Labor service charges for set installation Set up adjustment of customer controls and installation of repair or antenna systems are not covered by this warranty Reception problems caused by inadequate antenna systems are your responsibility 6 Warranties extend only to defects in materials or workmanship as limited above and do not extend to any productor parts which have been lost or discarded by you or to damage to products or parts caused by misuse accident damage caused by Acts of God such as lightning or fluctuations in electric power improper installation improper maintenance or use in violation of instructions furnished by us or to units which have been altered or modified withou
34. his product through openings as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock Never spill liquid of any kind on the product Attachments Do not use attachments not recommended by the product manufacturer as they may cause hazards Accessories Do not place this product on an unstable cart stand tripod bracket or table The product may fall causing serious injury to a child or adult and serious damage to the product Use only with a cart stand tripod bracket or table recommended by the manufacturer or sold with the product Any mounting of the product should follow the manufacturer s instructions and should use a mounting accessory recommended by the manufacturer A product and cart combination should be moved with care Quick stops excessive force and uneven surfaces may cause the product and cart combination to overturn Damage Requiring Service Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions a When the power supply cord or plug is damaged b If liquid has been spilled or objects have fallen into the product c Ifthe product has been exposed to rain or water d Ifthe product does not operate normally by following the operating instructions Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and
35. idental or consequential damages so the above provisions may not apply to you ATTENTION CANADIAN CONSUMERS Canadian consumers are requested to complete the special Canadian Warranty Registration Form enclosed and forward this completed form with a copy of bill of sale to TOSHIBA OF CANADA to Register and Validate their warranty Product must be purchased from an Authorized Canadian Dealer Products purchased in the U S A and used in Canada are not covered by these warranties IMPORTANT PACKING AND SHIPPING INSTRUCTION When you send the product to a Service Station you should use the original carton box and packing material then insert the original carton box containing the unite into another carton using more packing material TOSHIBA AMERICA CONSUMER PRODUCTS INC Printed in China Top General Descriptios Servicing Diagarms Part List SECTION 2 ADJUSTMENT PROCEDURES 1 MECHANICAL ADJUSTMENT 1 1 Mechanical Parts Location 1 2 Servicing Jig List 1 3 Main Parts Servicing Time 1 4 Mechanism Check Method 1 5 Mechanical Deck Removing and Mounting Method 1 6 Main Parts Replacement 1 7 Check and Adjustment 1 8 Self Check Function 2 ELECTRICAL ADJUSTMENT 2 1 PIF Circuit 2 2 Servo Circuit
36. ine etc Preparation Make sure that the clock is set correctly page 16 Load a cassette with a safety tab For cable box users Finish the cable box set up pages 33 36 and turn on the cable box For DSS satellite receiver users This VCR cannot record satellite programs with the VCR Plus C e system feature To make an unattended recording of satellite programs see Timer Program Recording pages 26 28 Sample of TV program listing in a TV guide magazine 5PM POPEYE Cartoon 725692 MAKING OF A CHAMPION 237945 A look at gymnast and Olympic hopeful Kim Zmeskal from novice to seasoned competitor NIK HEY DUDE Children PlusCode One of Ted s teachers stays at the ranch programming MY TWO DADS Comedy number 5 35 GOOD TIMES Comedy 2261858 VCR Plus C e system Programming Press VCR Plus The VCR Plus screen appears 2 Enter a PlusCode programming number Example To record a program with the procraul EIE ser up preser PlusCode programming number 36295 VOR BRS fictitious code o S28 um MODE Press number button 3 6 2 9 and 5 S SLP AUTO SP i i NN TO SET PLUSCODE Confirm that the number is entered PURH OUS ROC E correctly END GD Gus To correct a mistake press CANCEL and enter the correct number 3 Select MODE using CURSOR UP m g or CURSOR DOWN and set the ee recording frequenc
37. ion Select the video channel 3 or 4 or video input mode on the TV Make sure that the clock is set correctly page 16 Store the channels on the VCR pages 17 and 18 If you record cable channels finish the cable box set up pages 33 36 and turn on the cable box f you record satellite channels finish the DSS satellite receiver set up pages 37 39 and turn on the DSS satellite receiver Timer Programming Procedure Example To record cable channel 25 in the SP tape speed from 9 30 p m until 10 00 p m on August 30 Today is August 25 1 Load a cassette with the safety tab attached INPUT 2 Press PROG to display the MENU screen SELECT 3 Select PROGRAM using CURSOR Dracula oll 4 RIGHT or CURSOR LEFT and press ENTER Ses e ey II CURSOR UP m o a 4 Move to the next using CURSOR procnan ERI set up preser RIGHT and enter the channel number 25 by using CURSOR UP ange eee CURSOR DOWN or number alee crs ene buttons EE gs EM E EnD Gi To Record a cable program from the connected cable box Enter the cable channel number by number button PLAY or STOP If your cable box is not remote controllable choose the desired channel 1 to 125 on the cable box To record a satellite program from connected DSS satellite receiver Enter the satellite channel number 100 to 999 by number button PLAY or STOP
38. istorized and does not contain any parts that can be repaired by the user DO NOT REMOVE THE CABINET COVER OR YOU MAY BE EXPOSED TO DANGEROUS VOLTAGE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL ONLY 1 Read owner s manual After unpacking this product read the owner s manual carefully and follow all the operating and other instructions 2 Power Sources This product should be operated only from the type of power source indicated on the marking label If you are not sure of the type of power supply to your home consult your product dealer or local power company For products intended to operate from battery power or other sources refer to the operating instructions 3 Grounding or Polarization This product may be equipped with a polarized alternating current line plug a plug having one blade wider than the other This plug will fit into the power outlet only one way This is a safety feature If you are unable to insert the plug fully into the outlet try reversing the plug If the plug should still fail to fit contact your electrician to replace your obsolete outlet Do not defeat the safety purpose of the polarized plug 4 Ventilation Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating and these openings must not be blocked or covered The openings should never be blocked by placing the product on a bed sofa rug or other similar su
39. not work properly The batteries are exhausted Replace all batteries page 10 The remote control is operated beyond the operating range Make sure the remote control is within 30 of the remote sensor on the VCR page 10 Too far from the VCR Use the remote control within 7 m from the front of the VCR page 10 An obstacle may be in the way of the operation Remove the obstacle The operating mode of the remote control is not set correctly Press VCR or TV depending on the equipment you want to operate pages 14 42 The cassette is ejected immediately after it is loaded The cassette was inserted with the label side not paralleling the compartment Reload it carefully page 19 The cassette does not go into the cassette compartment There is already a cassette in the VCR Eject the cassette and reload the new one page 19 NOILVINYOSNI TVNOILIGGV a 45 Specifications Power supply Power consumption External dimensions Mass Channels received Antenna input output terminals Signal system Recording Playback system Cassette Tape speed Video recording playback time Fast forward time High speed rewind time Video input Video output Audio input Audio output Audio frequency range Hi Fi Audio dynamic range Hi Fi Utilization conditions Accessories Antenna cable eeeuseu Remote control
40. ode of tape operation back The playback speeds differ depending on the recording tape speed of the tape as follows Picture search Reverse playback SP xb x7 x1 SLP x15 x21 x3 Notes The still picture mode will be released automatically after about 5 minutes and forward playback will start Fast forwarding or rewinding started from the stop mode continues even if the shuttle dialis released To stop press STOP The reverse playback mode will be released automatically after about 25 seconds and forward playback will start Noise bar may appear in reverse playback Note If you playback a tape recorded in the SLP tape speed or a tape recorded on another VCR in various speed 22 mode the picture may be noisy or monochrome PLAYBACK Useful Functions in Tape Operation These functions will help your playback REMAIN COUNTER DISPLAY PLAY x2 STOP ENTER PROG S VHS Quasi Playback SQPB This VCR can also play back a tape which is recorded in S VHS format But the playback picture does not have the same quality and resolution as the original S VHS playback picture This VCR cannot record in S VHS format SQPB is an abbreviation for S VHS Quasi Playback Counter Function You can view the clock linear time counter or tape remaining time in the VCR display or on the TV screen changes in sequence as follows Linear time co
41. or clear out the line by pressing CANCEL and then press VCR Plus to enter a PlusCode programming number RECORDING Cable Box Set up The VCR can directly control channel selecting of the connected cable box Cable Box Control This VCR needs to be connected to a cable box equipped with an infrared wireless remote control You can select cable channels from the cable box by operating this VCR It is also possible to automatically change the cable channels according to your program setting in the timer program recording or VCR Plus C system recording Placing the Cable Box Put the cable box on the top of the VCR as shown below Do not block the sensor window Cable box AN Ms SOS 2 The infrared signals come out of the sensor window and the front of the VCR Then they bounce off walls and other objects in the room and are received by the cable box The VCR sends out infrared signals to your cable box even during timer program recording or VCR Plus C system recording Notes If the channels cannot be controlled properly because the infrared signal fails to reach the cable box change the position of the box on the VCR so that it can receive the signal Keep the cable box turned on even while the VCR is in the timer program recording or VCR Plus C e System recording Connection Type Type A DONIQHOO3H a 33 34 Cable Box Set up continued Preparation
42. own the stored channel numbers Number on the VCR TV 1 2 3 4 5 6 7 8 9 2 3 4 5 6 7 8 9 Corresponding channel number CATV STD HRC IRC 1 A 8 2 3 4 5 A 7 6 A 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 10 11 12 13 A B C D E F G H J K L M N O P Q 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 R S T U V W AA BB CC DD EE FF GG HH II JJ KK LL MM NN OO 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 PP QQ RR SS TT UU VV WW XX YY ZZ AAA BBB 65 66 67 68 69 70 71 93 94 95 96 97 98 99 100 101 102 103 121 122 123 124 125 93 94 A 5 A 4 A 3 A 2 A 1 100 101 102 103 121 122 123 124 125 CATV signals STD standard cable TV signals HRC Harmonic Related Carriers cable TV signals e IRC Incremental Related Carriers cable TV signals IRC is also called ICC Incremental Coherent Carriers 18 PREPARATION Video Cassette Use Video Cassette Use Loading a cassette Push the cassette into the cassette compartment with the window side facing up and the label side towards the front The VCR is automatically turned on The indicator will appear in the VCR display x NE 22 NN E dq u Ejecting a cassette Press EJECT The cassette is ejected from the cassette compartment
43. r Rear Panel LINE OUT VIDEO jack LINE IN 1 VIDEO jack RF IN FROM ANT terminal To wall outlet LINE IN 1 AUDIO jacks L R CH selector 3 4 RF OUT TO TV terminal LINE OUT AUDIO jacks L R LINE IN 1 AUDIO Rear 2 Front jacks If the connected equipment is monaural has one audio output jack connect the L MONO side the same sound is recorded on both L and R on the Hi Fi track 10 PREPARATION How to Use the Remote Control This section explains how to get ready for remote control operation Setting up the Remote Control 1 Open the battery compartment lid on the rear panel 2 Install 2 batteries AAA size following the polarity diagrams 3 Close the battery compartment lid 4 Point the remote control at the VCR and press the buttons within the operating range Distance within about 7 m from the front of the remote sensor Angles within about 30 in every direction Notes on batteries The life of the batteries is about 1 year Caring for the remote control Do not expose the remote sensor of the VCR depending on the conditions of use If the remote control does not operate correctly replace all batteries with new ones If the remote control is not to be used for a long period of time remove the batteries to avoid possible damage from battery corrosion to a strong light source such as direct sunlight or illumination especially high frequency lighting when using
44. r scrambled channel while recording it record any channels through the cable box NOILVHVdHHd i You will need to set TV channel 3 or 4 to receive video signals See page 11 set VCR channel to the output channel of the cable box and select a desired cable channel on the cable box while the VCR is turned off or the VCR indicator is not lit in the VCR display set TV channel to the output channel of the cable box This set up will enable you to watch an unscrambled or scrambled channel while recording it record an unscrambled channel while watching another unscrambled channel only when you connect a cable compatible TV A B switch A record and watch an unscrambled channel which comes bypassing the cable box A B switch B record and watch a scrambled or unscrambled channel coming through the cable box This set up will enable you to watch or record a channel through the cable box via the LINE IN 1 AUDIO VIDEO jacks You will need to press INPUT SELECT so that the VCR display shows L1 13 14 PREPARATION Auto Set Up The Auto Set Up function automatically sets the tuner channels and clock when power is first connected to the VCR Preparation Turn on the TV and select the video channel 3 or 4 or the video input mode if you made the Audio Video connection page 11 Press INPUT SELECT so that the channel number will appear if L1 or L2 is di
45. red at the index point and the index search may not work properly RECORDING Recording a TV Program This section explains the basic recording operation Preparation Select the video channel 3 or 4 or video input mode on the TV f you record cable channels via the cable box finish the cable box set up pages 33 36 and turn on the cable box Basic Recording 1 INPUT SELECT 2 3 Uo d Wh To record from other connected equipment In step 3 press INPUT SELECT to switch the display as follows LI To record via the LINE IN 5 1 jacks on the rear panel Load a cassette with the safety tab attached Press TV VCH so that the VCR POWER OO indicator appears in the VCR display ves Select a channel to record with FNRS CHANNEL on the VCR or CH TRK ver 2j or number buttons on the remote control If you see L1 or L2 in the VCR display press INPUT SELECT so that the channel number appears If you record cable channels via the cable box make the output channel number of the cable box or L1 appear depending on your connection See pages 11 13 Press SP SLP to select the PONENS recording tape speed S L vcr pu SP Suitable for general recording with zac better picture and sound quality SLP Suitable for tripling recording time but with less picture and sound quality than using the SP tape speed Press REC on the VCR or Mas IP TIMER sim
46. ress ENTER procraul ER set ue E preser CLOCK SET CH MEMORY CABLE BOX DSS GUIDE CH EnD Gi ENTER Press ENTER to select CLOCK SET Procranl TIE ser up E preser CLOCK SET SUMMER TIME TIME DATE YEAR iw OUT 12 00411 01 00 SA END GD Select AUTO or MANU using CURSOR UP or CURSOR DOWN AUTO The VCR automatically sets or adjusts the clock If you select AUTO mode proceed to step 8 MANU You can set the clock manually If you select MANU mode select SUMMER TIME using CURSOR RIGHT Set to IN or OUT for the summer daylight saving time using CURSOR UP or CURSOR DOWN For IN and OUT selections see the description in step 9 Move to the next using CURSOR RIGHT To move back press CURSOR LEFT Vary the digits to set the hour CURSOR UP To increase CURSOR DOWN To decrease Repeat steps 5 and 6 to set the minutes month day and the year by the last two digits Proceed to step 10 to start the clock Press ENTER to start the AUTO clock set feature After a while the VCR automatically updates the clock using the data broadcast by the local TV stations The following screen will appear on TV depending on the broadcast at your location procrau EIE ser up E preser CLOCK SET SUMMER TIME TIME ZONE CH AWO mIn AWOEASTER ANO 2 TIME DAT
47. rface This product should not be placedin a built in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer s instructions have been adhered to 5 Heat The product should be situated away from heat sources such as radiators heat registers stoves or other products including amplifiers that produce heat 10 11 Water and Moisture Nees Do not use this product near water for example near a bath tub wash bowl s cO kitchen sink or laundry tub in a wet basement or near a swimming pool and ML e the like 9 Clo Cleaning Unplug this product from the wall outlet before cleaning Do not use liquid cleaners or aerosol cleaners Use a damp cloth for cleaning Power Cord Protection Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them paying particular attention to cords at plugs convenience receptacles and the point where they exit from the product NOILONGOULNI i Overloading Do not overload wall outlets extension cords or integral convenience recep tacles as this can result in a risk of fire or electric shock Outdoor Antenna Grounding If an outside antenna or cable system is connected to the product be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built up static charges Article 810 of the National Electrical Code ANSI N
48. rol 10 Connections 5 tres cann an KR CERCARE 11 AUTO Set Up ner ct ace 14 Initial Settings Using On screen DIS DIAY eS 15 Setting the Language Optional settings on the SET UP screen Setting the Clock Storing Channels on the VCR 17 Video Cassette Use 19 PLAYBACK Explains variable functions concerning playback Play Dack iine ie riui 20 e 19u HEAD Variable Speed Playback 21 Picture Search e Still Picture Slow motion Picture Frame Advance Double Speed Playback Jog Dial Operation e Shuttle Dial Operation Useful Functions in Tape ODeFrallODi eire ca pasunp Seine EDeceoUaEcEE 23 Counter Function Tape Remaining Time e Index Search Function RECORDING Explains recording functions Recording a TV Program 25 e Watching a TV program while recording another Recording off time setting Timer Program Recording 26 VCR Plus C system Set up 29 VCR Plus C system Recording 31 Cable Box Set up 33 DSS Satellite Receiver Set up 37 MTS Broadcast Compatibility 40 Simulcast Recording 41 ADDITIONAL INFORMATION Multi Brand Remote Control 42 Before Calling Service Personnel 44 Specifications c o cer eeeecueee 46 Accessories ssse 46 LIM
49. splayed in the VCR display Press VCH to set the remote control operating the VCR Auto Set Up 1 Connect the antenna cable to the VCR see page 11 Then connect the VCR s power plug to an AC outlet Auto flashes in the VCR display as the VCR automatically tunes in all active stations When Auto Set Up is completed successfully the current time will be displayed VCR display VCR display PM ZEN j ER Tuning in progress Auto Set Up completed ay I7 Ii um AN 1717 JEN d gt e If the VCR fails to set the clock will be displayed Set the clock manually Refer to Setting the clock on page 16 Notes f you press the CANCEL button the Auto Set Up is cancelled f Auto Set Up is not perform successfully perform the clock and Tuner Channel procedures manually page 16 to 18 If however you want to add or delete channels refer to Adding or erasing channels on page 18 PREPARATION Initial Settings Using On screen Display Language selection must be set first when the VCR is first plugged in or after it encounters a power failure You can also easily make necessary settings using the on screen displays Preparation Turn on the TV and select the video channel 3 or 4 or the video input mode if you made the Audio Video connection page 11 Press VCR to set the remote control operating the VCR Setting the Language Press VCR POWER to turn on the
50. t Press REMAIN COUNTER The remaining time RT appears in the VCR display Notes The displayed remaining time is an approximation The remaining time is calculated according to the tape speed SP or SLP and the cassette type Index Search Function The VCR can find a point where a registered index signal is on a tape and play back for about 5 seconds You can easily locate the desired program by inputting the index signal Registering index signals Each time a recording starts an index signal is automatically registered To register it somewhere else press INDEX during recording Note A certain interval is required between the index signals more than 1 minute in the SP tape speed and more than 3 minutes in the SLP tape speed Index search 1 Load a cassette with the index signals registered 2 Press INDEX or in the stop or playback mode To search in the reverse direction To search in the forward direction The VCR fast forwards or rewinds the tape When an index signal is found the VCR plays back the tape for about 5 seconds and then resumes fast forwarding or rewinding This is repeated each time at an index signal 3 Press PLAY when the desired program is found Normal playback starts Notes At the very beginning of the tape the index search may not work properly If you registered the index signals on a tape recorded on another VCR the recording may be blur
51. t authorization of TACP THI orto damage to products or parts there of which have had the serial number removed altered defaced or rendered illegible 7 At you option after the warranty period has expired in the U S A Call 800 631 3811 to receive information concerning an exchange price Payment must be enclosed with the product in the form of a certified check or money order and forward your product to Toshiba America Consumer Products Inc Returns Center 1420C Toshiba Dr Lebanon TN 37087 8 Uponreceipt we will at our option replace your unit with a new or refurbished unit of equal value Features may notbe identicalto youroriginal product 9 Physically damaged units are not acceptable for repair or exchange in or out of warranty and will be returned as received NOIIVIWHOHNI TVNOILIGGV a 47 LIMITED WARRANTY continued How to Obtain Warranty Service 1 Refer to the troubleshooting guide in your owner s manual This check list may solve your problem 2 Call the TACP toll free number 800 631 3811 within 30 days after you find a defective product or part 3 Arrange for the delivery of the product to the Authorized TACP THI Service Station Products shipped to the Service Station must be insured and safely and securely packed preferably in the original shipping carton and a letter explaining the defect and also a copy of the bill of sale or other proof of purchase must be enclosed In the Continental United
52. t you can watch closer 1 Press PAUSE STILL during playback The picture freezes To resume normal playback Press PAUSE STILL Notes The still mode is automatically cancelled after about 5 minutes and returns to normal playback The still picture may shake if a picture of a fast moving object or scene is frozen This is not a defect in the unit Adjusting Still Picture Stability If the still picture is distorted or flickers hold down one of CH TRK until the picture becomes stable Note The distortion of the still picture may not be eliminated completely Note 2 To change the tape speed to 7 times the normal playback FF speed press and hold FF or REW If you release it the tape speed returns to 5 times Picture Search A tape runs at 5 times or 7 times the normal playback speed so that you can quickly locate a particular scene Press FF or REW during playback The tape runs at 5 times the normal playback speed 39V8AV 1d q If you press FF or REW during picture search the mode changes to fast forwarding or rewinding To resume normal playback Slow motion Picture The tape runs at 1 7th or 1 15th the normal playback speed 1 Press SLOW during playback The tape runs at about 1 7th the normal playback speed Each time you press SLOW the speed alternates between 1 7th and 1 15th To resume normal playback Press PLAY Notes The slow motion picture mode is automatically cancelled af
53. ted Reset the clock Overlaps of the programs If two timer programs overlap the recording start time of program 2 has priority over the recording off time of program 1 Overlapped portion not recorded Program 1 Start time Program 2 Start time S RECORDING VCR Plus C e system Set up VCR Plus C e system is a timer recording system for an easier programming that requires you only to enter a PlusCode programming number assigned to a desired program This section explains the necessary set up to make VCR Plus C system recordings The flow chart below will give you an idea Sample of a Guide channel chart from a local TV listing as to what must be done to use the VCR Plus C system feature VCR Plus SYSTEM CHANNEL NUMBERS Broadcast Assigned Cable Assigned CER INE channels i channels channels j 3 Setting the Clock page 16 OR l 10 KXTV CBS 13 KOVR ABO 19 KCSO SPAN Cable Box Set up page 33 S KERN d 40 KTXL FOX 58 KSCH IND 44 KBHK IND Storing Channels on the VCR 24 KCPM NBC 4 KRNV ae page 17 42 KFCB IND Ji 7 KGO ABC VCR Plus C system Set up l VCR Plus C36 system Recording ay a Channel line up chart from a cable TV page 31 With the VCR Plus C e system this video CHANNEL PINEUP CHART cassette recorder can automatically select the Channel 2 ME U appropriate channel on your compatible cable Channel 3 8 WISH box or satellite receiver VCR Plus C
54. ter about 5 minutes and returns to normal playback The slow motion picture may flicker up and down This is not a defect in the unit Adjusting the Tracking Manually If the slow motion picture is noisy hold down one of CH TRK until the best picture is obtained Note The noise in the slow motion picture may not be eliminated completely When playing back a tape which is recorded in S VHS format distortion may occur during the variable speed playback 21 Double Speed Playback A picture advances frame by frame A tape runs at twice the normal speed J Press PLAY during still playback 1 Press PLAY during playback Each time you press PLAY the picture The picture runs at twice the normal playback advances one frame speed If you press and hold PLAY the tape runs at To resume normal playback 1 30th the normal playback speed To resume normal playback Press PAUSE STILL Jog Dial Operation You can control the speed of frame advance 1 During playback press PAUSE STILL Press PLAY 2 Turn the jog dial on the Remote Control The speed of frame advance varies as you turn the jog dial When you stop turning the dial the picture freezes To cancel the jog dial mode Press PAUSE STILL Shuttle Dial Operation You can also activate the picture search and slow playback at various speeds by turning the shuttle dial on the VCR or Remote Control Turn the shuttle dial on the VCR or Remote Control Initial m
55. trolled by the DSS satellite receiver following buttons on the remote control of the TOSHIBA 99 Mp 98 cn POWER CABLE BOX A To turn the DSS satellite receiver on or off SONY CH CABLE BOX To select satellite channels in the upper or lower direction not applicable to some brands of DSS satellite receiver Number buttons 0 9 To select desired channels to record DNIQHOO3H i 39 40 RECORDING MTS Broadcast Compatibility This VCR can receive or record MTS Multichannel TV Sound broadcasts By connecting the VCR to your stereo system or stereo TV you will experience the SAP or stereo sound Preparation Connect a stereo TV or stereo system to the AUDIO OUT jacks of the VCR Recording the SAP Stereo Broadcast 1 On the SET UP screen page 15 E select SAP SET using CURSOR UP or CURSOR DOWN and set to zon ON using CURSOR LEFT or AUTO CURSOR RIGHT On OFF EnD Gi 2 Press PROG to exit 3 Perform a recording SAP Second Audio Program broadcast A separate audio program usually broadcast in a second language with the main language Selecting a sound Sounds recorded on the tape According to your setting of SAP SET on the SET UP screen the sound is recorded onto different tracks of the tape as below Set SAP SET to ON or OFF appropriately m Setting of SAP SET On Screen Displa
56. ture may condense on the cylinder inside one of its most crucial internal parts To prevent the VCR from possible damage do not use the unit for at least 2 hours when there is an extreme or sudden change in temperature Compatibility This video cassette recorder VCR is compatible with any other VCR bearing the VIS mark HQ VHS equipment is also compatible with existing non HQ VHS equipment Copyright Itis permissible to record television programs film video tapes and other material only in the event that third party copyrights and other rights are not violated product model meets the ENERGY Star guidelines for energy efficiency e As an Eneray Star Partner TOSHIBA has determined that this product or In the spaces provided below record the Model and Serial No located at the rear of your video cassette recorder Model No gt gt Serial No Retain this information for future reference NOILONGOULNI a IMPORTANT SAFETY INSTRUCTIONS CAUTION PLEASE READ AND OBSERVE ALL WARNINGS AND INSTRUCTIONS GIVEN IN THIS OWNER S MANUAL AND THOSE MARKED ON THE UNIT RETAIN THIS BOOKLET FOR FUTURE REFERENCE This set has been designed and manufactured to assure personal safety Improper use can result in electric shock or fire hazard The safeguards incorporated in this unit will protect you if you observe the following procedures for installation use and servicing This unit is fully trans
57. ultaneously press both REC on r3 5NIGHOO3H L2 To record via the LINE IN POWER GO 2 jacks on the front panel ine remore control fen Eu Recording starts ch Press STOP to stop recording Watching a TV program while Recording off time setting recording another By setting the recording off time the recording 1 While recording press TV VCH to turn off stops and the VCR is turned off automatically VCR indicator While recording press REC on the VCR 2 Choose another channel using the channel repeatedly to set the desired off time selector on the TV Each time you press REC each half hour up to ee z about 4 hours later and appear cyclically Skipping unnecessary scenes while recording POWERIGG PM _ _ gt o i ou wwNa amp S P VCR D or Press PAUSE STILL to stop recording B Cou tL momentarily To resume recording press Notes PAUSE STILL again To cancel the recording in progress press STOP Note If the VCR clock is not set this function will not The VCR automatically shifts to the stop mode if the activate recording pause mode continues for 10 minutes 25 26 RECORDING Timer Program Recording The programmable timer allows you to record up to 6 different programs over one month Preparat
58. unter HMS Tape remaining time REMAIN RT Clock 4 COUNT RESET Each time you press REMAIN COUNTER the VCR display The indication above will also appear on the TV screen by pressing DISPLAY They are switchable with REMAIN COUNTER To reset the linear time counter to OHOOMOOS The counter is automatically reset to 9H00MOOS when a cassette is ejected If you want to reset at another point such as the beginning of a new recording just press COUNT RESET Notes The linear time counter does not work on non recorded portions on the tape When the tape is ejected or the VCR is turned off the display changes to clock f the tape rewinds back over 0H00MOOS appears in the VCR display The displayed time of the linear time counter is only an approximation Tape Remaining Time To view the tape remaining time in the VCR display select the tape length beforehand 1 2 3 4 Turn on the VCR and load a cassette Press PROG to display the MENU screen Select SET UP using CURSOR RIGHT or CURSOR LEFT and press ENTER Select the length of the tape T120 for a T 120 tape or shorter T160 for a T 140 or T 160 tape T180 for a T 180 tape PROGRAM UN SET up E preset ISAP SET _ Oon on AUTO ENG FRA ESP on OFF EDD Gi MOVEAV 1d B Continued 23 24 Useful Functions In Tape Operation continued amp Press PROG to exi
59. will often require extensive work by a qualified technician to restore the product to its normal operation e Ifthe product has been dropped or damaged in any way f When the product exhibits a distinct change in performance this indicates a need for service Servicing Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards Refer all servicing to qualified service personnel Replacement Parts When replacement parts are required be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part Unauthorized substitutions may result in fire electric shock or other hazards Safety Check Upon completion of any service or repairs to this product ask the service technician to perform safety checks to determine that the product is in proper operating condition Contents INTRODUCTION Provides important notes and general explanation of the VCR including names of the buttons jacks etc SAFETY PRECAUTIONS 2 IMPORTANT PRECAUTIONS 3 IMPORTANT SAFETY INSTRUCTIONS 4 Contents oec uma did usks vex sus 7 Identification of Controls 8 Front Panel e Remote Control VCR Display Rear Panel PREPARATION Explains what you need to do before operating the VCR How to Use the Remote Cont
60. y a ONCE To record once EISE SLP AUTO SP DAILY MO FR To record programs on the same channel at the same time EnD GS ENTER Monday through Friday WEEKLY To record programs on the same channel at the same time on the same day every week 4 Select SPEED using CURSOR UP mn g or CURSOR DOWN and set the Csr ser up Ed preset recording tape speed oce S295 For AUTO speed see page 27 n ENTER DONIQHOO3H i Continued 3 1 VCR Plus C System Recording continued amp Press ENTER The program setting is now memorized If your cable box is not remote controllable select the recording channel on the cable box beforehand prosa EB ser up ES preser CH DATE On OFF SPD e 25 8 30 9 30 10 00PWSIE i e j e j e j e EDD Gig To set another program repeat steps 1 to 5 7 To finish press the two TIMER buttons simultaneously The VCR enters the timer standby mode Confirming the VCR Plus C system timer programs REC m TIMER POWER G TIMER Fe Recording or playback in the timer standby mode Before the VCR enters the timer standby mode TIMER indicator not lit 1 Press PROG to display the MENU screen 2 Press ENTER to select PROGRAM Check the programmed data 3 Press PROG to exit
61. y Contents of recorded sound Type of receiving lon the SET UP Press DISPLAY Normal sound HiFi sound track Screen SAP STEREO track Mono Regular monaural audio Stereo lit MONO MIXED STEREO not lit MONO Regular SAP not lit MONO Stereo SAP OFF lit lit MONO MIXED STEREO Sounds in playback You can play SAP and or stereo broadcasts with this VCR Press A SELECT to select a desired sound Desired sound L R indicators in the VCR display Sound output SAP sound R right is on SAP Stereo sound Both R right and L left are on Stereo Note When the TV is connected to the RF OUT terminal of the VCR the output sound is monaural RECORDING Simulcast Recording When TV program such as MTV HBO or MAX is being simulcast in FM stereo in your area the VCR can also record the simulcast sound from an FM stereo tuner or receiver onto the Hi Fi track and normal track Preparation Connect the TV and stereo system to the VCR as below Turn on the connected FM tuner and tune to the station for the simulcast program DO Broadcast or incoming cable AUDIO OUT AUDIO IN DNIQHOO3H i AUDIO OUT LINE IN 1 AUDIO 96 Simulcast Recording 1 On the SET UP screen page 15 select SIMULCAST using procran EID ser up E preser CURSOR UP or CURSOR DOWN on OFF and set to ON using CURSOR AUTO MANU
Download Pdf Manuals
Related Search