Home

Toshiba B-SA4T Printer User Manual

1. Press the PAUSE key AGC threshold for data write setting menu is displayed Choose a threshold value decimal number with the FEED or RESTART key When the measured AGC is 10 0A for example choose 9 a value lower than the measured AGC by 1 or 2 15 RESTART i 11 Default FEED i 0 Press the PAUSE key AGC threshold lower limit for retry setting menu is displayed Choose a lower limit decimal number with the FEED or RESTART key Usually choose the same value with the AGC threshold for data write WT AGC i 15 RESTART 11 Default FEED e 4 0 Press the PAUSE key RFID Setting Menu lt 10 gt RFID is displayed An AGC threshold setting is completed INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15 33001A Revision Date Nov 7 2008 8 RFID Module B SA704 RFID U2 EU R e Identification of The Rfid Module B SA704 RFID U2 EU R As from the production manufactured in October 2008 the standard label has been added to the RFID module which is used for the B SA4T series for improving the efficiency of assembly RFID Module Service No Label B SA704 RFID U2 EU R TRw EUM 01 CE 0682 O TOSHIBA TEC CORPORATION Serial No Label Note Descriptio of the serial number label and service number label Description of Service Number Label Description of Serial Number Label B SA704 RFID U2 EU R B SA704 RFID U2 EU R B 0500 02 08 5 D XXXX Service num
2. 2 Remove the two SMW 3x6 screws which secure the Side Panel Side Panel SMW 3x6 Screw Reverse side of Side Panel TT SMW 3x6 Screw 3 Close the Front Cover and remove the Side Panel Side Panel 8 4 INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15 33001A Revision Date Feb 25 2008 8 RFID Module B SA704 RFID U2 EU R 3 Slightly push the Upper Sensor Lever inside 1 and open the Upper Sensor Ass y 2 Upper Sensor Ass y Upper Sensor Lever 4 Pushing the tabs on the rear of the Media Sensor Block toward the front of the printer slightly lift the back of the Media Sensor Block and remove it toward the printer back Media Sensor Block re LE 5 Turn over the Media Sensor Block and secure the Antenna Ass y with the supplied three Tapping Screws Sensor Block Tapping Screw M 3x8 Antenna Ass y Tapping Screw M 3x8 8 5 INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15 33001A Revision Date Feb 25 2008 8 RFID Module B SA704 RFID U2 EU R 6 As the following picture shows pass the Interface Cable through the opening behind the Stepping Motor so that the cable reaches the Main PC Board Stepping Motor Main PC Board Interface Cable 8 Put the Interface Cable on the hooks provided on the Media Path Frame Media Path Frame Hook Interface Cable 8 6 INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15 33001A Revision Date Feb 25 20
3. Continued from the previous page PAUSE lt 10 gt RFID ERR CHK OFF PAUSE lt 10 gt RFID ISSUE RETRY 3 PAUSE lt 10 gt RFID RCYCLE CNT 5 PAUSE Continued to the next page Revision Date Feb 25 2008 8 RFID Module B SA704 RFID U2 EU R RFID tag type setting menu is displayed Choose EPC C1 Gen2 24 with the FEED or RESTART key RESTART NONE When a tag type is not selected FEED EPC C1 Gen2 24 Press the PAUSE key RFID error tag detection menu is displayed Choose whether to perform an error tag detection or not with the FEED or RESTART key RESTART OFF An error tag detection is not performed Usually choose OFF l OON Anerror tag detection is performed ON A tag is read before writing data on it and data is written on the tag only when the header data is A5A5 OFF Though a tag is read before writing data on it data write is always performed whatever data has been set as the header data Press the PAUSE key Max number of issue retries setting menu is displayed Set the maximum number of retries to issue an RFID tag When issuing an RFID tag failed the printer prints the error pattern and retries to issue the tag for up to specified number of times If the printer does not succeed even after having retried for the max times the printer stops resulting in an error Choose the max number of retries with the FEED or RESTAR
4. TOSHIBA TOSHIBA Thermal Printer B SA4T SERIES Document No EOQ15 33001A Original Jul 2005 Revised Sep 2005 PRINTED IN JAPAN TOSHIBA TEC CORPORATION EO15 33001A Revision Date Feb 14 2008 TABLE OF CONTENTS Page Cutter Module 220022022eennn sens nennnn nen nn anen seen ennnenneeneensenseenerneens 1 1 1 1 B SA204 QM B SA204 QM R 1 1 1 2 B SA204P QM R 1 4 Strip Module 2 02002 22 2n sens nen nnn sens enn enn nen nen nen ennnnnseenennsenseeneenenes 2 1 2 1 B SA904 H QM R 2 1 2 2 B SA904P H QM R 2 5 Wireless LAN Module B SA704 WLAN QM 6 3 1 Serial Interface Board B SA704 RS QN R 22 22 22 4 1 300 dpi Print Head Kit B SA704 TPH3 QN R 5 1 Real Time Clock B SA704 RTC QN R 2 2 2 ennnnnnnnnnnennnnnnnnennn 6 1 Expansion I O Board B SA704 10 QN R 922 2 nn nena nnn n nn
5. Turn the power ON Issue labels 7 Good Print position Adjustment is required Power OFF Power ON 7 m m J RESTART mmp Print position fine adjustmen lt 3 gt ADJUST SET FEED ADJ 0 0mm Strip position fine adjustment lt 3 gt ADJUST SET CUT ADJ 0 0mm Turn the power OFF Turn the power ON RESTART lt 1 gt DIAG V1 1 FEED lt 2 gt PARAMETER SET Continued 2 6 INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15 33001A Revision Date Jan 19 2006 2 Strip Module 13 14 15 16 Press the PAUSE key repeatedly until P P FEED appears on the LCD Press the FEED key to feed a label for checking the next label s stop position If the next label stops with its top edge aligning with the strip shaft edge an adjustment is not required Go to Step 15 If not press the RESTART key to return to P P FEED 0 0mm display and adjust the pre strip amount Set the value in a range from 9 9 to 2 5 with the FEED or RESTART key When the top edge of the label stops past the strip shaft edge set a negative value Top edge of the label A Ae f When the top edge of the label stops short of the strip shaft edge set a positive value Top edge of the label When the adjustment is completed press the PAUSE key twice to finish the setting Send an issue command to the printer and check
6. or RESTAT lt 10 gt RFID Press the PAUSE key to implement a read test READ TEST ON PAUSE lt 10 gt RFID READINGeee Continued to the next page INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15 33001A Revision Date Feb 25 2008 8 RFID Module B SA704 RFID U2 EU R Continued from the previous page 3 Set an AGC threshold of data write 3132333435363738 39304142 0A FEED RESTART lt 10 gt RFID Read data is displayed Data in parentheses is the AGC value expressed in hex code Write down this value Press the FEED and RESTART keys to return to the RFID Setting Menu lt 10 gt RFID Set a value which is lower than the AGC value obtained by a read test by 1 or 2 taking variation of RFID tags in performance into consideration Example lt 10 gt RFID PAUSE 2 A lt gt ey ci mgo lt q FEED or RESTART DA 7 D ci mgo PAUSE lt 10 gt RFID WT AGC FEED or RESTAT SA H o V 2T O L2 gJ PAUSE lt 10 gt RFID WT MIN AGC FEED or RESTAT lt 10 gt RFID WT MIN AGC 9 PAUSE lt 10 gt RFID When lt 10 gt RFID is displayed press the PAUSE key until the Q value setting menu is displayed Choose 2 with the FEED or RESTART key When 2 is already chosen go to the AGC threshold for data write setting menu 15 RESTART 2 Default FEED 6
7. 15 Pressing the PAUSE key enables choosing the RTC data renewal timing 16 Choose PAGE or BATCH with the FEED or RESTART key PAGE A real time can be printed on each media However the printer needs to stop the motion before printing each media to read the real time clock data BATCH Batch print is possible However the same time is printed on the all media issued in a batch because the real time clock data is read only for the first media Press the PAUSE key to fix the setting Then the current date is displayed 17 Press the FEED and RESTART keys at the same time to return to lt 8 gt RTC SET display lt Supplementary Explanation gt Continued from the previous page lt 8 gt RTC SET TIME H 00 00 00 FEED RESTART Minute FEED RESTART lt 8 gt RTC SET TIME M 10 00 00 Second FEED RESTART lt 8 gt RTC SET TIME S 10 30 00 lt 8 gt RTC SET LOW BATT CHECK lt 8 gt RTC SET LOW BATT OFF PAUSE FEED RESTART lt 8 gt RTC SET RENEWAL lt 8 gt RTC SET RENEWAL FEED RESTART BATCH lt 8 gt RTC SET DATE 06 03 01 FEED RESTART lt 8 gt RTC SET 1 Be sure to load the battery and set the low battery check function to ON whenever the real time clock is used If the battery is not loaded or the battery voltage is low the real time clock data is erased at the power off time 2 When the low battery check function is set to ON and if the battery voltage is
8. It is advisable to tear off or cut the backing paper outside the strip module cover e How to use the Guide Roller When issuing the label with the length of 50 mm or more fit the guide roller to the center of the strip module cover to prevent the stripped label from sticking to the cover Opening Guide Roller Strip Module Cover ____ WH vil TE Ht Wy I i H f ial iI ININ NOTE Regarding the system mode setting for use of PET paper refer to Section 2 1 INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15 33001A Revision Date Jan 19 2006 3 Wireless LAN Module B SA704 WLAN QM 3 Wireless LAN Module B SA704 WLAN QM The pictures used in this section are those of the B SA4TM and the installation procedures are common with the B SA4TP unless otherwise noted e Packing List The following parts are supplied with the kit Make sure you have all items shown below Wireless LAN Board 1 pc Antenna Cover 1 pc SMW 3x6 Screw 4 pcs Shield Sheet 1 pc NOTES 1 DO NOT CHANGE the DIP Switch settings on the Wireless LAN Board Doing so may cause a malfunction 2 MAC address of the Wireless LAN module will be necessary when setting the MAC address filtering function of an access point As it is printed on the top of the wired LAN connector on the Wireless LAN Board write down it on Installation Manual before mounting the covers so that an end user can know the MAC addres
9. battery with the mark facing up 2 A new battery is supposed to last about 2 years or more but it varies depending on the operating conditions When a new battery is loaded write down the battery replacement date on a supplied battery sticker and attach it to the reverse side of the Side Panel as a reminder Battery Sticker Reverse side of Side Panel 4 Attach the Real Time Clock to the printer with the SMW 4x8 screw Real Time Clock SMW 4x8 Screw 6 3 INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15 33001A Revision Date Jan 19 2006 6 Real Time Clock B SA704 RTC QM R 5 Pass the Interface Cable through the Cable Clamp and between CN1 and CN2 on the MAIN PC Board as shown in the pictures below For the B SA4TP model wind the cable on the two Cable Clamps B SA4TP Model Connector CN2 MAIN PC Board E ji Interface Cable Connector CN1 Cable Clamp Interface Cable B SA4TM Model Connector CN2 MAIN PC Board a E k t i yo ae i a pea Am uI rotia E TAE E Mta iis a mi o E EFE elni a oa 5 Sie or its ee i Ed a ae Interface Cable Connector CN1 Cable Clamp Interface Cable 6 Connect the Interface Cable to CN501 on the MAIN PC Board MAIN PC Board Interface Cable 7 Attach the Side Panel removed in Step 2 back to the printer Care must be taken not to catch the Interface Cable by the Side Panel NOTE When the B SA704 IO
10. ennnnnnnnnnes 7 1 RFID Module B SA704 RFID U2 EU R 8 1 CAUTION This manual may not be copied in whole or in part without prior written permission of TOSHIBA TEC The contents of this manual may be changed without notification Please refer to your local Authorised Service representative with regard to any queries you may have in this manual Copyright 2005 by TOSHIBA TEC CORPORATION All Rights Reserved 570 Ohito Izunokuni shi Shizuoka ken JAPAN INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15 33001A 1 Cutter Module INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT 1 Turn the printer power off and disconnect the power cord before installing an optional equipment 2 Be careful not to pinch your fingers or hands with the covers 3 Be careful not to injure your fingers when installing the cutter module 1 Cutter Module 1 1 B SA204 QM B SA204 QM R B SA204 QM B SA204 QM R is an optional cutter module for the B SA4TM Series Metal cover CAUTION Do not connect disconnect the cutter harness to from the printer within one minute from a power off to protect the internal electrical circuit of the printer e Packing List The following parts are supplied with the kit Make sure you have all items shown below Cutter Unit 1 pc Cutter Module Cover 1 pc Installation Manual 1 copy e Installation Procedure 1 Open t
11. for proper strip issue Strip Shaft Edge Continued I I PAUSE lt 2 gt PARAMETER SET P P FEED 0 0mm PAUSE A label is fed FEED Check the next label s stop position The next label stops with its top edge aligning with the strip shaft edge The next label stops with its top edge misaligning with the strip shaft edge RESTART lt 2 gt PARAMETER SET P P FEED 0 0mm 9 9mm 9 8mm RESTART simm 0 0mm FEED 0 1mm 2 4MM 2 5mm PAUSE PAUSE PAUSE BACK SPEED STD INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15 33001A Revision Date Jan 19 2006 2 Strip Module 2 2 B SA904P H QM R B SA904P H QM R is an optional strip module for the B SA4TP Series Plastic cover e Packing List Strip Unit 1 pc Strip Module Cover 1 pc SMW 3x6 Screw 4 pcs Cutter 1 pc NOTE When issuing labels in batch mode even though the strip module is fitted please use the provided cutter to tear off the issued labels Do not attach the cutter when labels are stripped one by one e Installation Procedure 1 Open the Top Cover and the Front Cover Remove the Connector Cover Top Cover Connector Cover i Front Cover AA hy ig 2 8 INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15 33001A 2 Strip Module 2 Open the Front Cover wider Remove the Front Cover by lifting it to disengage the hinge pins from the hinge The Front Cover cannot be
12. necessary For the downloading procedure refer to the B SA4T Series System Mode Manual 2 The countries where the use of this device is allowed are as follows UHF 869 7 to Austria Belgium Cyprus Czech Denmark Estonia Germany 870 0MHz Center Greece Finland France Hungary Ireland Italy Latvia frequency Lithuania Luxemburg Malta Poland Portugal Slovakia 869 85MHz Slovenia Spain Sweden the Netherlands and U K B SA704 RFID U2 EU R INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15 33001A Revision Date Feb 25 2008 8 RFID Module B SA704 RFID U2 EU R e Packing List All the following parts are supplied with the kit Make sure you have all items shown below Parts Quantity Parts Quantity Parts Quantity Antenna Ass y 1 pc RFID Module 1 pc Antenna Cable 1 pc I ia 7 j Interface Cable 1 pc Shield Sheet for the use of short pitch RFID Module Attaching Plate 1 pc tags 1 pc Cable Clamp 1 pc Edge Guard Long and short 2 pcs Installation Manual 1 copy each Tapping Screw M 3x8 3 pcs Double Sems Screw M 3x6 2 pcs 8 2 INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15 33001A Revision Date Feb 25 2008 8 RFID Module B SA704 RFID U2 EU R e Outline of the introduction of an RFID Kit Please follow the steps below to install the RFID kit configure various settings and try data write onto tags Install the RFID kit Refer to this section Set an RF
13. removed unless it is opened at an angle of over 100 degrees as the stoppers of the hinge prevent disengagement Front Cover Hinge Strip Module Cover Hinge 4 Fit the Shaft Holders of the Backing Paper Feed Roller into the cuts of the printer Shaft Holder t Backing Paper Feed Roller Strip Unit 2 9 INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15 33001A 2 Strip Module 5 Secure the Strip Unit to the printer with the two screws Make sure that the Feed Roller Gear rotates smoothly Strip Unit Feed Roller Gear 6 Close the Strip Unit Strip Unit e Media loading procedure Owner s Manual Section 2 3 e Operation check Owner s Manual Section 2 9 e System mode seiting System Mode Manual e Cleaning Owner s Manual Section 4 1 4 INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15 33001A Revision Date Jan 19 2006 2 Strip Module e Attaching the Cutter The enclosed cutter is used to tear off the batch issued labels Attach the cutter with the two SMW 3x6 screws as shown in the picture below Insert the leading edge of the labels into the opening under the cutter Opening SMW 3x6 Screw Strip Unit Cutter Edge NOTE Depending on the backing paper types tearing off the backing paper against the slot of the strip module cover may cause it to wind onto the inner rollers
14. to perform a read test or not with the RESTART or FEED key RESTART READ TEST OFF FEED READ TEST ON OFF A read test is not performed Initially choose OFF ON A read test is performed The printer enters the read test mode and a read test is performed each time the PAUSE key is pressed When the data of a tag can be read it is displayed on the LCD e Read data is displayed in hex value on the 16 digit x 2 line LCD 1234567890123456 6543210987654321 When the RFID tag contains 16 digits or more data the first 16 digits are displayed When data volume is less than 16 digits the vacant digits will be filled with spaces e If the tag cannot be read RFID TIMEOUT or RFID READ ERROR is displayed e If the type of the tag to be read and one selected by the RFID tag type selection do not match an RFID tag read error will result Make sure the RFID tag type has been selected before the read test is started After choosing an option press the PAUSE key Carrier sense setting menu is displayed This menu is not available to the B SA704 RFID U2 EU R Press the PAUSE key to skip this menu Module type setting menu is displayed Choose U2 with the FEED or RESTART key U1 Not available H1 not available NONE No RFID Module is installed FEED U2 B SA704 RFID U2 EU R H2 Not available Press the PAUSE key RESTART INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15 33001A
15. 08 8 RFID Module B SA704 RFID U2 EU R 9 Fit the supplied Edge Guards on the metal plate all the way to their bottoms e Please be careful not to injure your hands while fitting the Edge Guards e Fit the long Edge Guards and short ones on the correct positions respectively as indicated in the pictures below e The Edge Guards should not protrude from the edge of the metal plate portions enclosed with circles Edge Guard 10 Attach the Cable Clamp to the position shown below Cable Clamp 11 Temporarily secure the RFID Module Attaching Plate to the RFID Module with a supplied Double sems Screw Connect the Antenna Cable to the RFID Module until it clicks Antenna Cable _ RFID Module s Attaching Plate RFID Module Double Sems Screw M 3x6 8 7 EO15 33001A Revision Date Feb 25 2008 8 RFID Module B SA704 RFID U2 EU R INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT 12 Connect the Interface Cable to the RFID Module Interface Cable RFID Module 13 Secure the RFID Module to the printer with a supplied Double Sems Screw Double Sems Screw M 3x6 RFID Module I 14 While pushing down the RFID Module tighten the Double Sems Screw which was temporarily tightened in Step 10 so that there is no clearance between the RFID Module and the Bottom Plate le of the printer RFID Module RFID Module Attaching Plate Double Sems Screw M 3x6 Bottom Plate 8 8 INSTALLATION PR
16. 2 4V or less the printer will result in a LOW BATTERY error and stop at the power on time In that case hold down the RESTART key to restore to lt 1 gt RESET display 3 When LOW BATTERY error has occurred contact the nearest TOSHIBA TEC service representative for replacement of the battery 4 If you would like to keep using the same battery even after LOW BATTERY error occurs set the Low battery check function to OFF and set the date and time to the real time As long as the power is on the Real Time Clock will function However once the power is turned off the date and time will be reset Then please ask for the battery replacement 6 6 INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15 33001A Revision Date Jan 19 2006 7 Expansion I O Board B SA704 lIO QM R 7 Expansion I O Board B SA704 IO0 QM R B SA704 IO QM R is an optional expansion I O board for the B SA4TM SA4TP Series The pictures used in this section are those of the B SA4TP and the installation procedures are common with the B SA4TM unless otherwise noted e Packing List The following parts are supplied with the kit Make sure you have all items shown below Expansion I O Board 1 pc See Note Blind Plate 1 pc SMW 3x6 Screw 3 pcs Interface Cable Note Make sure that the Interface Cable is connected to CN1 on the Expansion PC Board 1 Remove the two SMW 3x6 screws from the back of the printer Si
17. D Module B SA704 RFID U2 EU R This optional device is intended for adding the RFID tag read write function to the B SA4TM and B SA4 TP series Follow all manual instructions Failure to do so could create safety hazards such as fire or electrocution e Manual instructions must be followed when installing option kits or adding cables to avoid system failures and to insure proper performance and operation e Failure to follow manual instructions or any unauthorized modifications substitution or change to this product will void the limited product warranty Turn the power OFF and disconnect the power cord before installing the RFID module Be careful not to pinch your fingers or hands with the covers The print head and stepping motor becomes very hot immediately after printing Do not touch the print head stepping motor and around it right after printing or you may get burned When opening the top cover it must be fully opened Failure to do this may cause the top cover to close under its own weight resulting in an injury CAUTION Be careful not to damage the pattern of the Antenna Ass y or peel off the Shield Sheet Damaged pattern or removed Sheild Sheet may affect the ability to read or write RFID tags Antenna Ass y Shield Sheet e Applicable Model This optional device is intended for the following models Notes 1 To use this device firmware V1 6 or greater is required Upgrade the firmware to V1 6 or greater if
18. EVER loosen or remove these screws 2 Do not touch the Print Head Element when handling the Print Head e Packing List The following parts are supplied with the kit Make sure you have all items shown below 300 dpi print head 1 pc Installation Manual 1 copy INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15 33001A 7 Expansion IO Board B SA704 lIO QM R e Installation Procedure 1 Fully open the Ribbon Cover 2 Slightly open the Top Cover 10 mm Ribbon Cover Top Cover J Oriiri 3 Unlock the Print Head by pressing the hooks toward the center Then pull the Print Head downward NOTE Care must be taken not to damage the Print Head Element by hitting it against any metal parts Hook Print Head B SA704 TPH3 QM R 5 Replace the Print Head with a new one and then reassemble in the reverse order of removal 3 2 INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15 33001A Revision Date Jan 19 2006 6 Real Time Clock B SA704 RTC QM R 6 Real Time Clock B SA704 RTC QM R B SA704 RTC QM R is an optional Real Time Clock for the BSSA4TM SA4TP Series The pictures used in this section are those of the B SA4TP and the installation procedures are common with the B SA4TM unless otherwise noted NOTE When the B SA704 IO QM R Expansion I O Board or B SA704 RS QM R Serial Interface Board has been already installed in the printer the Interface Cable of the Real Time Clock cannot be connected
19. FEED 4 0 coon nn IA A Press the PAUSE key Max number of write retries setting menu is displayed Set the maximum number of retries to write data onto an RFID tag The printer retries to write data onto an RFID tag for up to specified number of times If the timeout period expired before the max number of retries have been done the printer stops the retries at the time Set the max number of times with the FEED or RESTART key 255 RESTART i 5 Default FEED 0 Press the PAUSE key Write retry timeout setting menu is displayed Set the timeout period during which RFID tag write retries are allowed with the FEED or RESTART key If the printer has retried for the max number of times within the RFID write retry timeout the printer stops the retries at the time 9 9 9 9 sec RESTART 2 0 Default FEED 0 0 0 0 sec Press the PAUSE key INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15 33001A Revision Date Feb 25 2008 8 RFID Module B SA704 RFID U2 EU R Continued from the previous page RFID adjustment for retry menu is displayed If writing data on a tag failed the printer feeds the RFID tag forward or backward for ADJ RETRY 00 specified length in order to retry writing data When 0 is set for this parameter this function and a retry are not performed Only the value of 3mm or less or 3mm or more becomes effective Set a value to move the RFID tag posit
20. ID module type tag type etc in the printer system mode Refer to this section or section 2 9 of system mode manual In the printer system mode perform a read test to confirm the printer acknowledges the RFID module Refer to section 2 9 of system mode manual Discover an optimum feed amount and output power of the RFID module for data read write using the RFID Analyze Tool Refer to section 5 of system mode manual Set the feed amount by using an RFID Tag Position Adjustment Command ESC 003 and the output power of the RFID module by using an RFID Parameter Set Command ESC Z2 3 or printer system mode respectively For details of the commands refer to the B SA4T Series External Equipment Interface Specification Try tag read write with an application lf data write fails set an AGC threshold Refer to this section e Installation Procedure 1 Remove the two screws from the back of the printer gt Side Panel SMW 3x6 Screw 8 3 INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15 33001A Revision Date Feb 25 2008 8 RFID Module B SA704 RFID U2 EU R 2 Remove the Side Panel in the following order Please note the procedure is different between the B SA4TM series and the B SA4TP series B SA4TM B SA4TP 1 Open the Top Cover and Front Cover Open the Top Cover Slide the Side Panel backward Top Cover and then remove it in the direction of arrow A Top Cover S Side Panel Front Cover
21. OCEDURE FOR OPTIONAL EQUIPMENT EO15 33001A Revision Date Feb 25 2008 8 RFID Module B SA704 RFID U2 EU R 15 Re place the Media Sensor Block Media Sensor Block 16 Connect the Antenna Cable to the Antenna Ass y until it clicks and fasten the Antenna Cable with the Cable Clamp as shown below Antenna Cable Antenna Ass y Cable Clamp 17 Reattach the Side Panel to the printer with reference to Step 2 18 Close the Front Cover and the Top Cover Now an installation of the RFID Module has been finished In the case short pitch RFID tags 20mm are used refer to Section 4 to attach the Shield Sheet and Section 5 to configure the RFID module settings When short pitch tags are not used refer to Section 5 to configure the RFID module settings e When Short Pitch RFID Tags 20mm are used When short pitch tags 20 mm are used the supplied Shield Sheet needs to be attached for proper read write operation Follow the procedure below to attach the Shield Sheet to the Media Guide Bock 1 Before attaching the Shield Sheet move the Media Sensor to the right most position Failure to do this disables a media sensor position adjustment Media Sensor 8 9 INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15 33001A Revision Date Feb 25 2008 8 RFID Module B SA704 RFID U2 EU R 2 Insert the Shield Sheet without the backing paper removed under the Media Guides from behind and Slightly slide it toward the Plate
22. QM R Expansion I O Board or B SA704 RS QM R Serial Interface Board was removed beforehand re install it 6 4 INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15 33001A Revision Date Jan 19 2006 6 Real Time Clock B SA704 RTC QM R System Setting Date and Time Setting Set the date and time using the following procedure NOTE Make sure that the printer version is V1 2 or greater The real time clock is not supported by V1 1 or older 1 Turn on the printer ONLINE will be displayed on the LCD 2 Press the PAUSE key to turn the printer to pause state 3 Hold down the RESTART key until the printer enters the system mode NOTE For details of the system mode refer to the B SA4T Series Owner s Manual stored in the CD ROM supplied with the printer When lt 1 gt RESET is displayed on the LCD press the RESTART key until lt 8 gt RTC SET appears Press the PAUSE key The date currently stored in the real time clock is displayed Pressing the PAUSE key enables changing the Year Set the Year with the FEED or RESTART key Pressing the PAUSE key fixes the Year and causes the cursor to move to the Month Set the Month with the FEED or RESTART key Pressing the PAUSE key fixes the Month and causes the cursor to move to the Day Set the Day with the FEED or RESTART key Press the PAUSE key to fix the Day Then the time currently stored in the real time c
23. T key 255 RESTART 3 Default FEED l Press the PAUSE key Max number of read retries setting menu is displayed Set the maximum number of retries to read an RFID tag The printer retries to read the data in an RFID tag for up to specified number of times If the timeout period expired before the max number retries have been done the printer stops the retries at the time Whenever the printer writes data onto an RFID tag the tag is read first The max number of retries set by this parameter becomes also effective in this pre read Choose the max number of retries with the FEED or RESTART key 255 RESTART 7 5 Default FEED 0 Press the PAUSE key INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15 33001A Revision Date Feb 25 2008 8 RFID Module B SA704 RFID U2 EU R Continued from the previous page lt 10 gt RFID R CYCLE TIM 4 0 PAUSE PAUSE PAUSE l Continued to the next page Read retry timeout setting menu is displayed Set the timeout period during which RFID tag read retries are allowed with the FEED or RESTART key Ifthe printer has retried for the max number of times within the RFID read retry timeout the printer stops the retries at the time Whenever the printer writes data onto an RFID tag the tag is read first The read retry timeout set by this parameter becomes also effective in this pre read 9 9 9 9 RESTART
24. ance Opening 3 3 INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15 33001A Revision Date Jan 19 2006 3 Wireless LAN Module B SA704 WLAN QM 6 As the following picture shows secure the Wireless LAN Board to the printer back with two of the enclosed SMW 3x6 screws Also secure the Wireless LAN Board to the PCB Support Plate with the SMW 3x8 screw together with the Cable Clamp removed in Step 4 Copper foil Print Head Cable _ PCB Support Plate Cable Clamp SMW 3x8 Screw 7 Only when this option is installed in the B SA4TP printer remove the three backing papers from the shield sheet and attach the shield sheet so that it covers the wireless LAN module Shield Sheet Wireless LAN Module 3 4 INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15 33001A 3 Wireless LAN Module B SA704 WLAN QM 8 Connect the Wireless LAN Power Cable and the LAN Cable as shown below LAN Cable Wireless LAN Power Cable 9 Fit the Antenna Cover to the back of the printer Secure it with the SMW 3x6 screw SMW 3x6 Screw bes Antenna Cover Pass the LAN Cable through the cut of the Antenna Cover 10 Re attach the Side Panel to the printer 3 5 INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15 33001A 3 Wireless LAN Module B SA704 WLAN QM e Country Code As available frequency bands are different from country to country be sure to set a country code before installing a wireless LAN modu
25. ata write with the FEED or RESTART key if necessary 15 RESTART 11 Default FEED 0 Press the PAUSE key AGC threshold lower limit for retry setting menu is displayed When the Q value is set to 1 or greater the AGC threshold lower limit for retry becomes effective When there are tags of which AGC values fall within the range between the AGC threshold for data write and the lower limit the printer retries data write for a tag with the highest AGC value among those tags When printer retries data write that value is then used as an AGC threshold The optimum value differs depending on the tag type For details refer to Section 6 AGC Threshold Setting Set the lower limit for retry with the FEED or RESTART key if necessary 15 RESTART m 11 Default FEED 0 Press the PAUSE key The LCD message returns to lt 10 gt RFID Now the RFID module settings are completed If data write to RFID tags cannot be properly performed refer to Section 5 INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15 33001A Revision Date Feb 25 2008 8 RFID Module B SA704 RFID U2 EU R e AGC Threshold Setting The B SA704 RFID U2 EU R chooses a tag to write data on according to a radio intensity of RFID tags AGC value An AGC threshold value has been set to 11 OBh as factory default but it may be necessary to change this value according to the tag type to be used When the factory default threshol
26. ation check for a proper cut issue e Media loading procedure Owner s Manual Section 2 3 e Operation check Owner s Manual Section 2 9 e System mode seiting System Mode Manual e Cleaning Owner s Manual Section 4 1 3 INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15 33001A Revision Date Jan 19 2006 2 Strip Module 2 Strip Module NOTE Make sure that the firmware version is V1 1 or greater Firmware V1 0 does not support the strip module 2 1 B SA904 H QM R B SA904 H QM R is an optional strip module for the B SA4TM Series Metal cover e Packing List The following parts are supplied with the kit Make sure you have all items shown below Strip Unit 1 pc Strip Module Cover 1 pc SMW 3x6 Screw 4 pc Cutter 1 pc NOTE When issuing labels in batch mode even though the strip module is fitted please use the provided cutter to tear off the issued labels Do not attach the cutter when labels are stripped one by one e Installation Procedure 1 Open the Top Cover and the Front Cover Remove the B 3x6 screw to detach the Connector Cover Top Cover Connector Cover Front Cover B 3x6 Screw INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15 33001A 2 Strip Module 2 Open the Front Cover wider Remove the Front Cover by lifting it to disengage the hinge pins from the hinge The Front Cover cannot be
27. ber B 05000 01 For EU Serial number odule type C EU Month 1 9 A 10 B 11 C 12 Least 2 digit of the Christian Era
28. d value is not proper for the tag type used follow the procedure below to configure the following settings As the changes are stored in the internal memory they are retained after the printer power is turned off and on again When the tag type is changed or data write cannot be operated properly perform the setting again Step 1 Load an RFID tag embedded media in the printer Step 2 Follow the procedure below to measure the radio intensity of the tags 1 Place the media so that an RFID tag IC chip is positioned above the Antenna and close the Top Cover Sater Media Antenna Cable te RFID Module Note If an RFID tag is not positioned above the Antenna while the Print Head is at a print start position use 003 command to adjust the media position so that an RFID tag is positioned above the Antenna For detail of the command refer to the External Equipment Interface Specification Printer Command Manual 2 Start the printer in the system mode and perform a read test to measure the AGC value Example Turn the printer on while holding down the FEED and PAUSE keys at the same time When lt 1 gt DIAG V1 6 is displayed press the RESTART key i RESTART Vv lt 10 gt RFID When lt 10 gt RFID is displayed press the PAUSE key PAUSE lt 10 gt RFID Read test menu is displayed READ TEST OFF Press the FEED or RESTAT key to choose READ TEST ON l FEED
29. de Panel SMW 3x6 Screw INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15 33001A Revision Date Jan 19 2006 7 Expansion I O Board B SA704 lIO QM R 2 Remove the Side Panel in the following order Please note the procedure is different between the B SA4TM series and the B SA4TP series 1 Open the Top Cover and Front Cover Open the Top Cover Slide the Side Panel backward and then remove it in the direction of arrow A Top Cover a Front Cover 2 Remove the two SMW 3x6 screws which secure the Side Panel SMW 3 6 Screw N r SMW 3x6 Screw Blind Plate NOTE Keep the Blind Plate for future use 7 2 INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15 33001A Revision Date Jan 19 2006 7 Expansion I O Board B SA704 lIO QM R 4 Attach the Expansion I O Board to the printer back with one of the supplied SMW 3x6 screws SMW 3 6 Screw Expansion I O Board CN4 Connector a MAIN PC Board 6 Attach the supplied Blind Plate to the printer back with t e supplied two SMW 3x6 screws L SMW 3 6 Screw E NOTE The Blind Plate is not required to be attached when the optional Serial Interface Board is also installed ry Blind Plate Serial Interface Board 8 Attach the Side Panel removed in Step 2 back to the printer 7 3 INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15 33001A Revision Date Feb 14 2008 8 RFID Module B SA704 RFID U2 EU R 8 RFI
30. ears on the LCD lt 2 gt PARAMETER SET PRE PEEL OFF ON PAUSE RESTART 8 This menu is to set the strip motor torque As the default is RO choose R3 with the FEED or RESTART key Then press the PAUSE key lt 2 gt PARAMETER SET P P FEED 0 0mm NOTE Setting the motor torque higher makes the strip issue easier torque Low i R1 R2 High RESTART lt 2 gt PARAMETER SET PEEL OFF TRQ R3 lt 2 gt PARAMETER SET Continued 2 5 INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15 33001A Revision Date Jan 19 2006 2 Strip Module 9 Turn off the printer and then back to on Send an issue command to the printer for Strip issue 10 If necessary fine adjust the print start position and strip position in the system mode NOTES 1 Itis recommended that the print start position and strip position are adjusted on the actual print condition 2 When short pitch labels are used the print start position may misalign on the first few labels In that case feed the labels between the media sensor and the strip shaft and discard them Media Sensor Strip Shaft Discard labels between the media sensor and the strip shaft 11 Repeat Steps 9 and 10 for position fine adjustment 12 After the print position and strip position are properly adjusted access lt 2 gt PARAMETER SET menu in the system mode again Continued Turn the power OFF
31. he Front Cover and remove the B 3x6 screw to detach the Connector Cover Connector Cover Front Cover B 3x6 Screw INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15 33001A 1 Cutter Module 2 Open the Front Cover wider Remove the Front Cover by lifting it to disengage the hinge pins from the hinge The Front Cover cannot be removed unless it is opened at an angle of over 100 degrees as the stoppers of the hinge prevent disengagement Front Cover Cutter Module Cover Hinge Hinge Pin Hole Hinge Pin Cutter Unit Hinge Pin Hole INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15 33001A 1 Cutter Module 5 Connect the Cutter Harness to the connector at the front of the printer Cutter Harness 6 Close the Cutter Unit and secure it to the printer with the Set Screw E ET E g Set Screw r A a ee 7 Close the Cutter Module Cover Owner s Manual Section 2 3 Owner s Manual Section 2 9 System Mode Manual Owner s Manual Section 4 1 3 e Media loading procedure e Operation check e System mode setting e Cleaning 1 3 INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15 33001A 1 Cutter Module 1 2 B SA204P QM R B SA204P QM R is an optional cutter module for the B SA4TP Series Plastic cover CAUTION Do not connect disconnect the cutter harness to from the printer within one m
32. he next page INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15 33001A Revision Date Feb 25 2008 8 RFID Module B SA704 RFID U2 EU R Continued from the previous page lt 10 gt RFID Q VALUE 2 PAUSE PAUSE 11 PAUSE lt 10 gt RFID Q value setting menu is displayed In the case multiple RFID tags are read at the same time this menu is useful to pinpoint a target tag Set the Q value to 1 or greater 2 is recommended with the FEED or RESTART key Q value 0 causes the tags to interfere with each other and disables proper data write When a Q value is set set an AGC threshold for data write and an AGC threshold lower limit for retry also Setting all these values enable writing data to a tag placed just above the antenna For details refer to Section 6 AGC Threshold Setting The factory default is 2 15 RESTART 2 Default FEED i 0 Press the PAUSE key AGC threshold for data write setting menu is displayed When the Q value is set to 1 or greater the AGC threshold for data write becomes effective When the obtained gain of an RFID tag is lower than the AGC thresholdfor data write data write is not performed In other words setting an AGC threshold for data write enables writing data only to a tag placed just above the antenna The optimum value differs depending on the tag type For details refer to Section 6 AGC Threshold Setting Set an AGC threshold for d
33. inute from a power oft to protect the internal electrical circuit of the printer e Packing List The following parts are supplied with the kit Make sure you have all items shown below Cutter Unit 1 pc Cutter Module Cover 1 pc Installation Manual 1 copy e Installation Procedure 1 Open the Front Cover and remove the Connector Cover B 3x6 Screw 2 Open the Front Cover wider Remove the Front Cover by lifting it to disengage the hinge pins from the hinge The Front Cover cannot be removed unless it is opened at an angle of over 100 degrees as the stoppers of the hinge prevent disengagement Front Cover Stopper INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15 33001A 1 Cutter Module 3 Mount the Cutter Module Cover by inserting the hinge pins into the hinges eT F D P Cutter Module Cover ik Hinge Hinge Pin Hole Hinge Pin Cutter Unit Hinge Pin Hole 5 Close the Cutter Unit and secure it to the printer with the Set Screw Set Screw Cutter Unit INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15 33001A 1 Cutter Module 6 Secure the ground wire of the cutter unit to the printer with the B 3x6 screw removed in Step 1 as shown in the picture 7 Connect the cutter harness to the connector at the front of the printer Connector Cutter Harness Ground Wire Cutter Harness 8 Close the Cutter Module Cover After that perform an oper
34. ion with the FEED or RESTAT key jj 99 99mm Reverse feed RESTART 00 Default FEED 4 99 99mm Forward feed PAUSE Press the PAUSE key lt 10 gt RFID Radio output power level setting menu is displayed When the value is 9 the power is the weakest and when 18 the power is the strongest The factory default setting is 18 The optimum value differs depending on the tag types Usually it is not necessary to change this value but changing the value may be able to increase the number of successful read write times Set the power level with the FEED or RESTART key 18 Default Strongest RESTART s FEED 9 Weakest PAUSE Press the PAUSE key AGC threshold setting menu is displayed When the obtained gain of an RFID tag is lower than the AGC threshold the tag is considered as an error tag even if a data write succeeds When the AGC threshold is set to 0 all tags are writable When set to 8 for example only tags with the AGC threshold level of 9 or greater are writable The optimum value is different depending on the tag types The factory default is 0 Set an AGC threshold with the FEED or RESTART key 15 RESTART FEED O Default PAUSE Press the PAUSE key lt 10 gt RFID RFID channel setting menu is not available to the B SA704 RFID U2 EU R RF CHANNEL AUTO PAUSE Press the PAUSE key to skip this menu Continued to t
35. le in a user s printer Also ask an end user to confirm a country code Use of a wireless LAN module with a wrong country code could violate each country s Laws and Regulations for Radio Equipment and violators could be subject to penalties The country code cannot be changed through the Web browser but TELNET lt How to set a country code using TELNET gt CAUTION The following information must not be disclosed to users Internal use only 1 Disconnect the LAN cable connected to the printer connect the printer to a host PC with a straight LAN cable via a relay connector When using a hub in place of a relay connector use a cross cable or Open the MS DOS prompt type in telnet 192 168 10 21 default IP address Enter a password to log in Password tecbcp From the top menu change a country code using the following command gt ctry XX XX new country code See Country Code Table The new country code will become effective by turning the printer off and on again A country code can be checked by typing gt ctry on the telnet console Sus NO N FY Ca lt Country Code Table gt Country Country name Sountiy Country name county Country name code code code DE Germany T italy f LU f Luxembourg ES Spain NL Netherlands CH Switzerland IS Iceland LI Liechtenstein NZ NewZealand _ AT Austria DK Denmark Regarding various settings or operation check for the wi
36. lock is displayed 6 5 ONLINE B SA4T V1 2 PAUSE lt _ PAUSE B SA4T V1 2 RESTART lt 1 gt RESET RESTART lt 8 gt RTC SET lt 8 gt RTC SET DATE 05 01 01 lt 8 gt RTC SET DATE Y 05 01 01 FEED RESTART PAUSE Month FEED RESTART lt 8 gt RTC SET DATE M 06 01 01 lt 8 gt RTC SET DATED 06 03 01 Day FEED RESTART lt 8 gt RTC SET TIME 00 00 00 Continued INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15 33001A Revision Date Jan 19 2006 6 Real Time Clock B SA704 RTC QM R 10 Pressing the PAUSE key enables setting the Hour 11 Set the Hour with the FEED or RESTART key Pressing the PAUSE key fixes the Hour and cause the cursor to move to the Minute 12 Set the Minute with the FEED or RESTART key Pressing the PAUSE key fixes the Minute and cause the cursor to move to the Second 13 Set the second with the FEED or RESTART key Press the PAUSE key to fix the Second Then the Low Battery Check selection screen is displayed 14 Pressing the PAUSE key enables choosing whether to activate the low battery check function or not Set the function to ON or OFF with the FEED or RESTART key ON Low battery check function is activated OFF Low battery check function is not activated Default Press the PAUSE key to fix the setting Then the RTC Data Renewal Timing setting screen is displayed
37. n Then move the Media Guides to the width of the Shield Sheet shorter width as the pictures show The purpose of this is to indicate the center of the attachment osition p Platen Media Guide ees ay zm I Ba E J E ei oe Shield Sheet Media Guide q Ti J p 4 W Shield Sheet Media Guide 3 Remove the backing paper from the Shield Sheet and attach it to the position determined in the previous step as indicated in the picture below Now the Shield Sheet attachment is completed Next refer to Section 5 and configure the RFID module settings Media Guide Block Shield Sheet INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15 33001A Revision Date Feb 25 2008 8 RFID Module B SA704 RFID U2 EU R e RFID Module Settings After installing the RFID Module on the printer configure the RFID module settings using the system mode on the printer Turn on the printer while holding down the FEED and PAUSE keys at the same time lt 1 gt DIAG V1 6 RESTART lt 10 gt RFID PAUSE y lt 10 gt RFID READ TEST OFF PAUSE lt 10 gt RFID CAREERSENSE OFF PAUSE A lt 10 gt RFID MODULE NONE PAUSE Continued to the next page When lt 1 gt DIAG V1 6 appears on the LCD press the RESTART key RFID setting menu lt 10 gt RFID is displayed Press the PAUSE key Read test menu is displayed Choose whether
38. pending on the backing paper types tearing off the backing paper against the slot of the strip module cover may cause it to wind onto the inner rollers It is advisable to tear off or cut the backing paper outside the strip module cover Strip Module Cover Slot e How to use the Guide Roller When issuing the label with the length of 50 mm or more fit the guide roller to the center of the strip module cover to prevent the stripped label from sticking to the cover Opening Guide Roller Strip Module Cover SO Man 2 4 INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15 33001A Revision Date Jan 19 2006 2 Strip Module e System Mode Settings for Stripping PET Labels When using PET labels on the strip module please set the following system mode parameters in advance 1 Connect the printer to a PC 2 Load a PET label stock on the printer Turn the power ON 3 Turn ON the printer while holding down the FEED key and PAUSE key 4 When lt 1 gt DIAG is displayed on the LCD press the FEED key to choose lt 2 gt PARAMETER SET menu 5 Press the PAUSE key repeatedly until PRE PEEL OFF appears on the LCD 6 As the default is OFF choose PRE PEEL OFF ON with the FEED or RESTART l PAUSE _ key Then press the PAUSE key ze nia Hi lt 2 gt PARAMETER SET 7 a FEED 0 0mm is displayed on the PRE PEEL OFE OFF Press the PAUSE key repeatedly until PEEL OFF TRQ app
39. reless LAN refer to the System Mode Manual 3 6 INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15 33001A 4 Serial Interface Board B SA704 RS QM R 4 Serial Interface Board B SA704 RS QM R The pictures used in this section are those of the B SA4TM and the installation procedures are common with the B SA4TP unless otherwise noted e Packing List The following parts are supplied with the kit Make sure you have all items shown below SIO PC Board 1 pc Locking Support 1 pc PCB Support Plate 1 pc NOTE Make sure that the Serial Interface Cable is connected to CN4 on the SIO PC Board e Installation Procedure 1 Remove the two screws from the back of the printer SMW 3x6 Side Panel INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15 33001A 4 Serial Interface Board B SA704 RS QM R 2 Remove the Side Panel in the following order Please note the procedure is different between the B SA4TM series and the B SA4TP series 1 Open the Top Cover and Front Cover Open the Top Cover Slide the Side Panel backward and then remove it in the direction of arrow A Top Cover i Top Cover Front Cover Side Panel 2 Remove the two SMW 3x6 screws which secure the Side Panel SMW 3 6 Screw N 4 3 Remove the two screws to detach the Blind Plate Blind Plate SMW 3x6 4 2 INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15 33001A 4 Serial Interface Board B SA704 RS QM R 4 At
40. removed unless it is opened at an angle of over 100 degrees as the stoppers of the hinge prevent disengagement Hinge Strip Module Cover S Strip Unit Backing Paper Feed Roller 2 2 INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15 33001A 2 Strip Module 5 Secure the Strip Unit to the printer with the two screws Make sure that the Feed Roller Gear rotates smoothly _ Feed Roller Gear 6 Close the Strip Unit Strip Unit 7 Connect the Strip Harness to the connector at the front of the printer At this time carefully avoid contact of the strip harness with the gears Connector Strip Harness Strip Harness 8 Close the Strip Module Cover Perform an operation check for a proper strip issue e Media loading procedure Owner s Manual Section 2 3 e Operation check Owner s Manual Section 2 9 e System mode setting System Mode Manual e Cleaning Owner s Manual Section 4 1 4 2 3 INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15 33001A Revision Date Jan 19 2006 2 Strip Module e Attaching the Cutter The enclosed cutter is used to tear off the batch issued labels Attach the cutter with the two SMW 3x6 screws as shown in the picture below Insert the leading edge of the labels into the opening under the cutter SMW 3x6 Screw Opening Strip Unit Cutter Edge NOTE De
41. s 3 Be careful not to hit or damage the antenna when installing this kit A damaged antenna may affect the performance 12 digit code printed on the right side of W is MAC address Antenna Wireless LAN Board 4 The shield sheet is used only when this option is installed in the B SA4TP model INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15 33001A 3 Wireless LAN Module B SA704 WLAN QM e Installation Procedure 1 Remove the two SMW 3x6 screws from the back of the printer Side Panel SMW 3x6 2 Remove the Side Panel in the following order Please note the procedure is different between the B SA4TM series and the B SA4TP series B SA4TM B SA4TP 1 Open the Top Cover and Front Cover Open the Top Cover Slide the Side Panel backward and then remove it in the direction of arrow A a Top Cover ac _ Top Cover Front Cover Side Panel 2 Remove the two SMW 3x6 screws which secure the Side Panel SMW 3 J6 Screw _ 3 2 INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15 33001A Revision Date Jan 19 2006 3 Wireless LAN Module B SA704 WLAN QM Blind Plate SMW 3x6 4 Remove the SMW 3x8 screw to detach the Cable Clamp Cable Clamp SMW 3x8 Screw 5 Put the Antenna of the Wireless LAN Board out of the opening in the printer back Care must be taken not to hit the Antenna against the printer frame as damaged antenna may affect the perform
42. tach the enclosed PCB Support Plate to the printer back with one of the enclosed SMW 3x6 screws SMW 3x6 PCB Support Plate 5 Fit the Locking Support into the MAIN PC Board MAIN PC Board Locking Support SIO PC Board Serial Interface Cable 4 3 INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15 33001A 4 Serial Interface Board B SA704 RS QM R 7 Secure the SIO PC Board to the printer back with the two SMW 38x6 screws Fit the Locking Support into the SIO PC Board SIO PC Board 8 Re attach the Side Panel 9 Foran operation check settings etc refer to the 4 4 INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15 33001A 5 300 dpi Print Head Kit B SA704 TPH3 QM R 5 300 dpi Print Head Kit B SA704 TPH3 QM R B SA704 TPH3 QM R is an optional 300 dpi print head kit for the B SA4TM SA4TP GS12 Series 203dpi printer You will obtain the same print quality as the TS12 model 300 dpi only by replacing the current print head with this optional kit The pictures used in this section are those of the B SA4TM however the installation procedure is common with the B SA4TP WARNING Do not touch the print head or its neighboring parts immediately after printing or you may burn yourself CAUTION 1 NEVER loosen or remove the following two screws of the Print Head as they have been fine adjusted before shipment If they are loosened or removed print quality may become deteriorated N
43. to the MAIN PC Board Please remove this optional PC board temporality prior to installing the Real Time Clock e Packing List The following parts are supplied with the kit Make sure you have all items shown below Real Time Clock 1 pc See Note SMW 4x8 Screw 1 pc Lithium Battery CR2032 1 pc Interface Cable Battery Sticker 1 pc Note Make sure that the Interface Cable IS connected to CN1 on the Real Time Clock e Installation Procedure 1 Remove the two SMW 3x6 screws from the back of the printer P SMW 3x6 Screw INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15 33001A Revision Date Jan 19 2006 6 Real Time Clock B SA704 RTC QM R 2 Remove the Side Panel in the following order Please note the procedure is different between the B SA4TM series and the B SA4TP series 1 Open the Top Cover and Front Cover Open the Top Cover Slide the Side Panel backward and then remove it in the direction of arrow A Top Cover i Top Cover Front Cover Side Panel 2 Remove the two SMW 3x6 screws which secure the Side Panel SMW 3 6 Screw P E r 3 Place the Lithium Battery into the Battery Socket in the direction of the arrow Battery Socket Lithium Battery i PRE ast Yo oO IPEN mee a C Acs 6 2 INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15 33001A Revision Date Jan 19 2006 6 Real Time Clock B SA704 RTC QM R NOTES 1 Place the

Toshiba B-SA4T Printer User Manual

Contents

Download Pdf Manuals

Related Search

Related Contents