TOA Electronics FX 5.1 Speaker User Manual
Contents
1. EARTH BLUE NEUTRAL BROWN LIVE As the colours of the wires in the mains cable may not correspond with the coloured markings identifying the terminals in your plug proceed as follows e The wire that is coloured GREEN and YELLOW must be connected to the terminal in the plug that is marked either by the letter E the earth safety symbol or coloured GREEN or GREEN and YELLOW The wire which is coloured BLUE must be connected to the terminal in the plug which is marked by the letter N or coloured BLACK The wire which is coloured BROWN must be connected to the terminal in the plug which is marked by the letter L or coloured RED Ensure that the terminals are tightened securely and no loose strands of wire are present Ensure cord grip is clamped over outer sheath of cable rather than over the wires FUSE PROTECTION An additional mains fuse is provided in the IEC power inlet on the amplifier panel removable with a screwdriver A fuse of the same type and rating must always replace this The correct type is 5mm x 20mm Time Delay Type T e T1 6AL 125V for AC 220 240V 50Hz operation e T800mAL 250V for AC100 120V 60Hz operation TANNOY Tannoy Limited Home Audio Division Coatbridge Scotland ML5 4TF Tel 44 0 1236 420199 Fax 44 0 1236 428230 e mail sales tannoy com www tannoy com Tannoy adopts a policy of continuous improvement and product specification is subject to change FOR YOUR OWN PROTECTION Store the co2. the system and slowly increase the volume level control until roughly the correct amount of bass is present Listen to the system adjusting the VOLUME LEVEL control to achieve the most seamless integration of energy with your satellite speakers In some installation situations due to room acoustics setting the PHASE switch to 180 will give better results Fine adjustment of the controls will take a little time using a range of different programme material Remember that the object of a subwoofer is to enhance the output of your main speakers not overpower it REAR RIGHT POSITIONING As the FX5 1 subwoofer produces low frequencies only it is difficult to detect its location by ear It can therefore be placed anywhere in the room but optimum performance will be gained by locating the subwoofer between the front pair of speakers Bass output will increase next to a wall or especially in a corner so use the VOLUME control to compensate if moving your subwoofer around AUTO POWER SLEEP FUNCTION The FX 5 1 subwoofer can be left permanently on in AUTO mode under which conditions it will revert to sleep mode after approximately 20 minutes If not using your subwoofer for some time switch OFF and remove the power cable from the mains outlet POWER REQUIREMENTS Check that the voltage rating displayed on the rear panel is correct for your area before connecting If it is in
3. SET UP GUIDE TANNOY FAAS lt CQuinesanoy fannoyecom FX 5 1 Subwoofer This high performance 5 1 system has been built and tested with care and precision to provide first class performance and reliable operation To ensure maximum benefit from ownership and for reasons of safety please read the following information before using for the first time WALL MOUNTING OPTION BRACKETS SUPPLIED AV RECEIVER DECODER OUTPUT PANEL CENTRE QO FRONT REAR LEFT LERT D CONNECTING FX 5 1 SUBWOOFER TO YOUR SYSTEM The FX5 1 subwoofer may be connected in any one of the following ways LINE LEVEL e Using the subwoofer output on your A V receiver or decoder connect a single RCA interconnect to either the left or right line input on the subwoofer rear panel This is the ideal connection type as the subwoofer output contains the low frequency information from all channels If no subwoofer or spare line outputs exist you may connect using a Y split connector on the main preamplifier output connections Use a Y split on both right and left outputs and connect these via an RCA interconnect to the left and right inputs on the subwoofer rear panel Alternatively if your preamplifier has a spare set of line level outputs connect left and right to the FX 5 1 subwoofer L and R inputs using screened cable HIGH LEVEL e Use your amplifier s speaker out terminals To accom
4. correct move the voltage selector on the rear panel to the appropriate voltage The panel mounted fuse should also be changed to the correct rating see below under FUSE PROTECTION If in any doubt consult your Dealer or Authorised Service Agent woo SAouue Lu LO a LL T SUBWOOFER PERFORMANCE Recommended amplifier power Maximum Sensitivity 2 83Volts 1m PERFORMANCE Power output Nominal impedance Frequency response 6dB Frequency response 6dB Driver Drivers Inputs Crossover frequency Power requirements Magnetic shielding Fuse ratings Weight Additional features Dimensions H x W x D Weight Finish Supplied accessories Dimensions H x W x D Optional accessories Finish Due to our policy of continuous improvement this is a specification update sheet that should be read along with the manual as it provides the latest correct information All specifications may be subject to further change without notice HIGH LEVEL INPUT RI L CAUTION IMPORTANT A mains cable is supplied where the moulded plug is fitted with a mains fuse always replace with the same type and rating If the fitted plug is unsuitable for your type of outlet sockets it should be cut off and disposed of safely The wires in the mains cable are coloured in accordance with the following code GREEN AND YELLOW
5. modate the connection of two sets of cables red goes to red and black to black twist wires together and connect to the amplifier terminals e Alternatively use the A amp B speaker outputs on the amplifier if provided A to your main speakers and B to the FX5 1 subwoofer Do this using a length of speaker cable for each channel wire your amplifier outputs to the HIGH LEVEL input terminals on the subwoofer amplifier panel Ensure there are no stray wire strands that could possibly short together and damage both the amplifier and subwoofer WARNINGS e Double check all connections before switching on the FX 5 1 system and your amplifier SUB OUT e Ensure that the polarity of the speaker cables from your amplifier to the subwoofer is correct failure to observe this will result in damage to your amplifier e When using the HIGH LEVEL inputs ensure that your amplifier is not configured in bridge mode damage could result to either the amplifier or the subwoofer If in doubt consult your dealer SETTING UP Ensure the POWER switch is in the OFF position and that the POWER light is green You can operate FX subwoofer in two modes AUTO and ON continuously In AUTO the unit remains OFF until an input signal is detected Firstly set VOLUME control to MIN and the PHASE switch to 0 The LED will turn red when switched ON or when a signal is detected in AUTO mode Play some music through
6. mplete packaging in case it is needed for re use e Never expose the unit to moisture water and extremes of temperature or humidity Specifically the unit shall not be exposed to dripping or splashing and that no objects filled with liquids such as vases shall be placed on the unit Allow 150mm behind the unit to allow for sufficient ventilation Articles such as newspapers tablecloths curtains etc must not impede the ventilation Do not operate with the rear panel facing a radiator or heater No naked flame sources such as lighted candles should be placed on the apparatus Never remove the rear panel of the unit as there is a risk of electric shock There are no user serviceable parts inside the unit Always refer servicing to your Tannoy dealer or authorised service agent Avoid violent shocks to the unit during packing or transportation Do not plug the unit into the mains until all other connections have been made and checked Due to the powerful magnet within FX 5 1 subwoofer do not place within 1m of a television or computer monitor When set to the standby and off functions a small amount of current continues to flow to the apparatus when not in use If not used for a long period of time it is recommended that the apparatus is completely disconnected at the AC mains socket Terminals marked with the flash symbol are hazardous live and the external wiring connected to these terminals requires installation by an instructed perso
7. n or the use of a ready made lead or cord e This apparatus is designed for use in moderate climates WARRANTY Please complete and return the enclosed warranty registration document this does not limit your legal rights This equipment has been produced and tested with care and precision It is built to give first class service and carries a 1 year warranty If the equipment proves to be defective within this period for any reason other than accident misuse unauthorised modification or fair wear and tear Tannoy will repair any such defect or at our option replace it without charge for parts labour or return carriage This warranty is given in addition to the customer s statutory rights If you suspect a problem with your loudspeakers please contact your local Tannoy dealer who will be able to advise on appropriate action 6481 0381
Download Pdf Manuals
Related Search