TOA Electronics C-CV14-CS Digital Camera User Manual
Contents
1. Zoom ring P Focus ring Back focal length adjustment ring 8 ABOUT THE MODE SETTING SWITCH Set the Mode Setting switch for the best possible picture reproduction depending on installation conditions Mode Setting Switch Factory preset setting OFF ON Adjustment switch E 1 Backlight Compensation switch m Shutter Speed switch NTSC 1 60 1 100 VIDEO OUT PAL 1 0 1 1 20 8 1 Adjustment Switch Set this switch when adjusting the lens focus Provides the same effect as when using the ND filter OFF ON Standard position m Set to OFF after lens adjustment completion Set to this position during normal use E OFF ON Adjustment position during adjustment Use this position when focusing the lens If the focus is adjusted for a subject under co good lighting conditions the subject may go out of focus when conditions become co dark Set the Adjustment switch to ON only when performing focus adjustment Note The color of the screen may periodically vary under fluorescent lighting when the Adjustment switch is set to ON 8 2 Backlight Compensation Switch Set this switch so that the subject is not displayed in black when backlit OFF ON Standard position Set to this position during normal use Backlight Compensation function does not m operate when the switch is set to this position C SON Backlight2. Compensation position when backlit C This position prevents images from being displayed in black when the image is backlit C 8 3 Shutter Speed Switch Set this switch to the ON position when annoying screen image flicker is detected OFF ON Standard position CI Set to this position during normal use Shutter Speed position OFF ON Annoying screen flicker may result under fluorescent lighting in areas operating with a power frequency of 50 Hz NTSC or 60 Hz PAL In such cases set the Shutter Speed switch to the ON position to permit a flicker free picture to be viewed Note If the Shutter Speed switch is set to the ON position sensitivity is reduced compared to operation in the OFF position When using the camera in a dark location or where light flicker is not an annoyance set the switch to the OFF position 10 9 IF YOU THINK THERE IS A FAILURE TROUBLESHOOTING Symptom Possible Cause Remedy Camera images are not displayed on the monitor The monitor s power switch is not set to ON Cables are not correctly connected The BNC plug is not correctly soldered Power is not supplied to the camera Turn on the power switch Connect correctly Solder correctly Switch on the power Pictures are not clear The lens is not properly focused The lens is dirty Monitor image black level is not correctl
3. If water or a foreign object enters the unit If the unit falls or the unit case breaks If the power supply cord is damaged exposure of core or disconnection If no image is displayed on the screen Do not open nor modify the unit s case to prevent a fire or electric shock because there are high voltage components inside the unit Refer all inspection adjustment and repair work to the dealer from where the unit was purchased Do not insert or drop metal pieces or flammable materials into the unit s ventilation slots as this may result in fire or electric shock Have the unit periodically checked by the dealer from where it was purchased Should the unit or its mounts corrode or structurally deteriorate the unit could fall down possibly resulting in personal injury Indicates a potentially hazardous situation which could result in AN CAUTION moderate or minor personal injury and or property damage if ignored or mishandled Avoid installing the unit in humid or dusty locations in locations exposed to the direct sunlight near the heaters or in locations generating sooty smoke or steam as doing otherwise may result in fire or electric shock Leave the unit s installation to the dealer from where the unit was purchased because the installation requires expert knowledge Inadequate installation may cause the unit to fall possibly resulting in personal injury Do not hang from the unit as the unit may fall possibly resulting
4. mounting bracket optional Lens Optional Connector from the lens Lens connector Pin name Damping coil Damping coil Driving coil C Driving coil Notes Under 5 mm NEC MR HUS To avoid damaging the internal sections of the camera s lens mount be sure that the lens flange is less than 5 mm thick as illustrated on the right C mount lenses must be used in conjunction with the Lens Mounting Adapter CF 5 optional Lens Il When used 1 3 type lens an angle of view becomes narrow 2 Mount the optional camera mounting bracket to a ceiling or wall Using an electrical box fix the camera mounting bracket with its supplied screws Run the coaxial cable through the hole in the bracket 3 Set the camera mounting bracket securely in the threaded hole in the camera mount rotating the bracket s pedestal Notes The camera mount can be mounted to both the top and bottom of the camera Attach the bracket to either side depending on installation conditions Use the camera mount fixing screw to attach or detach the camera mount 4 Set the camera orientation and secure the camera After setting the camera orientation rotate the lock lever to secure the camera 6 CONNECTIONS Note If the Video output is not terminated at 75 video pictures are not properly displayed Make sure that the output has been terminated at 75 Q at the connected monitor or sw
5. Z TOA INSTRUCTION MANUAL COLOR CAMERA C CV14 CS NTSC C CV14 CS PAL Thank you for purchasing TOA s Color Camera Please carefully follow the instructions in this manual in order to ensure long trouble free use of your color camera TOA Corporation TABLE OF CONTENTS 1 SAFETY PRECAUTIONS 3 2 GENERAL DESCRIPTION 4 3 HANDLING PRECAUTIONS 4 4 NOMENCLATURE iatis es 5 5 INSTALLATION oh eh TUM tutte 6 6 CONNECTIONS see a iced a PU Fre Qe seg 7 ZSADJUSIMENT censu 8 8 ABOUT THE MODE SETTING SWITCH 8 1 Adjustment SWibGli cene aa nad true cA pU AT Uam LEE 9 8 2 Backlight Compensation Switch 2 4 041 9 8 3 Shutter Speed SWIOIT 9 9 IF YOU THINK THERE IS A FAILURE TROUBLESHOOTING 10 10 SPECIFICATIONS fein cod 11 Optional Products assai nennen 11 1 SAFETY PRECAUTIONS Before installation or use be sure to carefully read all the instructions in this section in order to ensure long trouble free operation Be sure to follow all the precautionary instructions in this section which contain important warnings regarding safety After reading k
6. adjustment is factory preset to an optimum position for general use avoid tampering with it in normal conditions Turning the control unnecessarily could cause reduced picture quality or equipment failure When the Iris control needs to be readjusted to match a specific subject first set both the Adjustment switch and the Backlight Compensation switch of the Mode setting switch to the OFF position then adjust the control to an optimum level After adjustment place a hand over the lens for several seconds and then release to check the lens for correct iris operation If the focus is adjusted for a subject under good lighting conditions the subject may go out of focus when conditions become dark To avoid this adjust the lens focus after setting the Adjustment switch of the Mode setting switch to the ON position Be sure to switch it back to the OFF position after completing lens adjustment When a subject appears out of focus because it is closer than the lens minimum close up distance adjust the focus as follows Back focal length adjustment 1 Attach the lens 2 Loosen the Back focal length adjustment ring fixing screw 3 Rotate the Back focal length adjustment ring to set it to an optimum position 4 Retighten the Back focal length adjustment ring fixing screw Ceiling panel Back focal length adjustment ring fixing screw Camera mounting bracket optional Lock lever
7. eep this manual handy for future reference Safety Symbol and Message Conventions Safety symbols and messages are used in this manual to prevent bodily injury and property damage which could result from mishandling Before doing anything else read this section first so you are thoroughly aware of the potential safety hazards as well as understanding the safety symbols and messages Do not expose the unit to rain or an environment where it may be AN WARNING splashed by water or other liquids as doing otherwise may result in fire or electric shock WARN Indicates a potentially hazardous situation which could result in death or serious personal injury if ignored or mishandled Install the unit only in a location that can structurally support the weight of the unit and the mounting bracket Doing otherwise may result in the unit falling and causing personal injury Do not install the unit outdoors since it is designed for indoor use If installed outdoors the aging of parts causes the unit to fall down possibly resulting in personal injury Also when it is exposed to rain an electric shock may result Should any of the following irregularities be found during use immediately switch off the power disconnect the power supply cord from the AC outlet and contact your TOA dealer Do not attempt to further use the unit because a fire or electric shock may result If you detect smoke or a strange smell coming from the unit
8. in personal injury NTSC version complies with Part 15 of the FCC Rules Note This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help Modifications Any modifications made to this device that are not approved by TOA Corporation may void the authority granted to the user by the FCC to operate this equipment Underwriters Laboratories Inc UL has not tested the performance or reliability of the security aspects of this product UL has only tested f
9. itcher BNC plug 24 V AC or 12 V DC Use the external power supply unit of the following rating when the camera is operated on 12 V DC 12 V DC over 1 0 A OFF oi Sumen Monitor Video input Video output 7 ADJUSTMENT 1 Switch on the camera power after completing camera connections Power is supplied to the camera Normally set the Shutter Speed switch to 1 60 NTSC or 1 50 PAL position Flickering of the picture may interfere with the view under fluorescent lamp in the area with power frequency of 50 Hz NTSC or 1 60 Hz PAL In such cases set the switch to 1 100 NTSC or 1 120 PAL position and the image free from flickering can be obtained Note If the Shutter Speed switch of the Mode Setting switch is set to the ON position sensitivity is reduced compared to operation in the OFF position When using the camera in a dark location or where light flicker is not an annoyance set the switch to the OFF position Connect the monitor to the Video Output terminal to permit a picture to be viewed on the monitor Adjust the camera angle Loosen the camera mounting bracket s lock lever to point the camera to the desired direction then retighten the lock lever to fix the camera securely Adjust the angle of view with the Zoom ring and adjust the focus with the Focus ring for the best possible picture reproduction Notes Since the Iris control for sensitivity
10. or fire shock or casualties as outlined in UL s Standard s for Safety UL Certification does not cover the performance or reliability of the security hardware and security operating software UL MAKES NO REPRESENTATIONS WARRANTIES OR CERTIFICATIONS WHATSOEVER REGARDING THE PERFORMANCE OR RELIABILITY OF ANY SECURITY RELATED FUNCTIONS OF THIS PRODUCT 2 GENERAL DESCRIPTION The C CV14 CS Color Camera is a high resolution surveillance camera equipped with a 1 4 CCD It is designed to operate on 24V AC or 12V DC The CS mount permits the optional lens that is the most appropriate for each application to be selected 3 HANDLING PRECAUTIONS Do not point the camera toward the sun or other strong lighting or reflected light Avoid jarring or striking the camera as the camera may fail Install the camera in locations where the temperature range does not exceed 10 C to 50 C and no dew condensation is formed To clean wipe with a soft dry cloth Never use benzene thinner or chemically treated towel to avoid damage to the camera s finish To clean the lens use a camera blower or lightly wipe with lens cleaning paper Picture quality may suffer if camera cables are wired close to other electrical equipment such as fluorescent lamps In such cases reroute the wiring Monitor screen pictures may become distorted or roll if the camera is used in locations influenced by strong electrical or magnetic fields from television t
11. ransmission antennas motors or transformers In such cases install the cables inside sheet steel cable conduit Use the external power supply unit of the following rating when the camera is operated on 12 V DC 12 V DC over 1 0A 4 NOMENCLATURE 1 Lens connector 7 Iris control 2 Back focal length adjustment ring 8 Video output terminal BNC fixing screw 3 Camera mount fixing screw 9 Mode setting switch 4 Camera mount 10 Camera mount fixing hole 5 Back focal length adjustment ring 6 Power input terminal 24 V AC or 12 V DC Note Fixing holes 10 are provided in both the top and bottom panels 5 INSTALLATION Ceiling mounting example Ceiling panel Camera mounting bracket optional Lock lever Pedestal Camera mount A WARNING Install the unit only in a location that can structurally support the weight of the unit and the mounting bracket Doing otherwise may result in the unit falling down and causing personal injury 1 Attach the lens to the camera Insert the lens into the camera s lens mount and rotate to full stop Connect the connector from the lens to the lens connector Note DC drive type lenses can be used however Video type lenses cannot be used Lens connector 2 1 Wall mounting example Wall Camera mounting bracket optional Wall Camera
12. y paint Dimensions 63 4 W x 62 7 H x 102 5 D mm Weight 300 g The specifications of this camera are subject to change without notice Optional Products Camera mounting bracket 11 Printed in Vietnam AW TOA Corporation 133 12 881 7D WR
13. y adjusted Adjust the lens Wipe the lens Adjust the level correctly The color of the picture periodically varies The Adjustment switch is set to the ON position Set the Adjustment switch to the OFF position 10 SPECIFICATIONS Model No C CV14 CS NTSC C CV14 CS PAL Power Source 24 V AC 50 60 Hz or 12 V DC Power Consumption 2W Image Device 1 4 IT CCD Number of Effective Pixels 768 H x 494 V 380 000 pixels 752 H x 582 V 440 000 pixels Scanning System 2 1 interlace Scanning Frequency 15 625 kHz H 50 Hz V 15 734 kHz H 59 94 Hz V Video Output VBS1 0 V p p 75 BNC connector Synchronizing System Internal synchronization Resolution H 480 lines center V 350 lines H 470 lines center V 410 lines S N Ratio 48 dB Minimum lllumination Ix F 1 4 50 IRE Ix F 1 4 350 mV White Balance Mode ATW Lens Mount CS mount Auto lris Lens Output DC drive type 4 pin connector Control Switch ON OFF for focus adjustment Other Functions Backlight compensation Shutter speed iris control Shutter Speed 1 60 1 100 1 50 1 120 Operating Temperature 10 to 50 C Operating Humidity Under 90 RH no dew condensation Finish Case Surface treated steel plate light gray paint Front cover Alminum light gra
Download Pdf Manuals
Related Search