Stiga 8211-0288-01 Lawn Mower User Manual
Contents
1. put the throttle control at full throttle approx 1 cm behind the choke position 6 Press down the brake pedal fully 7 Turn the starter key and start the engine 8 Once the engine has started move the throttle control gradually to full throttle if the choke has been used 9 When starting a cold engine let the engine run for a few minutes before using the machine This allows the oil to warm up When in use always run the engine at full throttle STOPPING Disengage the power take off Apply the parking brake Allow the engine to idle for 1 2 minutes Stop the engine by turning off the starter key Shut off the fuel cock This is particularly impor tant if the machine is to be transported on a trailer for example If the machine is left unattended re A move the lead from the spark plug Re move also the starter Key after the engine is stopped Do not touch the silencer cylinder or cooling flanges to avoid burn injuries OPERATING TIPS Make sure that there is the correct quantity of oil in the engine when driving on slopes oil level at FULL The engine can be very hot immediately sudden starting or stopping when mov ing up or down a slope Never drive across a slope Drive from the top and down or from the bottom and up Be careful when driving on slopes No When going down slopes greater than 20 the rear wheels can lift from the ground However the mower deck pre vents2. Make sure that the fibre gasket and O ring inside the plug are undam aged and in the correct position Take out the oil dipstick and fill up with new oil to the FULL mark Oil capacity Royal 0 9 litre when changing total engine capacity is 1 15 litre Oil type for all seasons SAE 10W 40 Fir very low temperatures lt 20 C use SAE SW 30 Do not use any additives with the oil Do not overfill This can result n the engine over heating AIR FILTER ENGINE Master Senator Comfort President Clean the pre filter every year or after every 25 op erating hours whichever comes first Clean the paper filter every year or every 100 op erating hours whichever comes first Royal Clean the air filter per filter and paper filter every 3 months or after every 50 operating hours which ever comes first Change the paper filter every year or every 200 operating hours All models NOTE Clean both filters more often if the ma chine is used in dusty conditions 1 Remove the air filter cover fig 12 13 2 Dismantle the paper filter and pre filter foam plastic filter Make sure that no dirt gets into the carburettor Clean the air filter housing 3 Wash the pre filter n liquid detergent and water Squeeze dry Pour a little on the filter and squeeze in the oil 4 Clean the paper filter as follows Tap it lightly against a flat surface If the filter is very dirty re plac
3. STIGA VILLA ROYAL PRESIDENT SENATOR COMFORT MASTER 8211 0288 01 Va T i G Es 13 Royal 12 Master Senator Comfort President ENGLISH GENERAL This symbol means WARNING Per sonal injury and or damage to property can occur if the instructions are not fol lowed carefully You must read these operating instruc tions and the enclosed pamphlet SAFETY INSTRUCTIONS carefully before starting the machine SYMBOLS The following symbols are displayed on the ma chine to remind you of the care and attention re quired when using the machine The symbols mean Warning LU Read the instruction book and safety man ual before using the machine Warning A Beware of objects being flung out Keep spectators away Warning Always use hearing protectors Warning XK This machine is not intended to be driven on public roads Warning The machine equipped with original ac cessories must not be driven in any direc tion on slopes with a gradient of more than 10 Warning ye Risk for burn injuries Do not touch the si lencer CONTROLS AND INSTRUMENTS Items 1 9 see figures 1 3 1 ACCESSORY LIFTER Pedal for lifting front mounted accessories to transport position To lift up the accessory press down the pedal as far as 1t goes Release the pedal and the accesso
4. Y SYSTEM This machine 1s equipped with a safety system that consists of a switch at the gear lever only Master Senator Comfort a switch at the brake pedal only President Royal aswitch in the seat mounting all In order to start the machine the following are nec essary ENGLISH gear lever in neutral only Master Senator Comfort brake pedal pressed down driver sitting on the seat Always check the operation of the safe A ty system before using the machine With the engine running and the driver sitting on the seat check as follows select a gear and lift your weight off the seat the engine should stop only Master Senator Comfort press the drive pedal so that the machine starts to move and then release the drive pedal the ma chine should stop applies to President Royall engage the power take off lift your weight off the seat the power take off should disengage The machine must not be used if the A safety system does not work Take the machine to a service agent for inspec tion STARTING 1 Open the fuel cock fig 9 2 Check that the spark plug cable is in place 3 Check that the power take off is disengaged 4a Master Senator Comfort Put the gear lever in neutral Ab President Royal Do not keep your foot on the drive pedal 5 Starting cold engine put the throttle control in the choke position Starting warm engine
5. ationary and with the engine switched off Always apply the parking brake to pre A vent the machine from rolling tarily always release the spark plug lead from the spark plug and earth it Remove the minus lead from the bat tery CLEANING y To prevent starting the engine involun To reduce the risk of fire keep the en sine silencer catalytic converter bat tery and fuel tank free from grass leaves and oil To reduce the risk of fire regularly check the machine for oil and or fuel leakage When washing the machine with water under high pressure do not point the jet directly at the trans mission Do not point the jet at the engine Use a brush or compressed air to clean it CHANGING THE OIL Master Senator Comfort Presi dent Change the engine oil for the first time after 5 hours of operation and then after every 50 hours of operation or once per season Change the oil more often every 25 hours of oper ation or at least once per season if the engine has to operate under very demanding conditions or if the ambient temperature is high Change the oil when the engine is warm Use a good grade of oil service grade SF SG or SH drained off directly after switching off the engine For this reason allow the en sine to cool for a few minutes before draining the oil The engine oil may be very hot if it is Unscrew the oil drain plug fig 10 It is located on the left sid
6. e it 5 Assemble in the reverse order Petroleum based solvents such as kerosene must not be used to clean the paper filter These solvents will damage the filter Do not use compressed air to clean the paper filter The paper filter must not be oiled SPARK PLUG Change the spark plug after every 100 hours of op eration or every season In the accessory bag there is a spark plug sleeve A and torsion pin B to change the spark plug The engine manufacturer recommends Master Senator Comfort President Champion J19LM Royal NGK BPRSES or DENSO WI6EPR U Correct electrode gap 0 75 mm fig 14 COOLING AIR INTAKE ENGINE Master Senator Comfort Presi dent The engine is air cooled A blocked cooling sys tem can damage the engine The engine should be cleaned every 100 hours of operation or at least once a year Remove the fan casing Clean the cooling fins on the cylinder the fan and the rotating protective grille fig 15 Clean more frequently if moving dry grass BATTERY Check the acid level regularly The acid level should lie between the UPPER and LOWER markings on the battery fig 16 When adjusting the acid level only use distilled water and can cause burns on the skin and clothing Use rubber gloves and protect your eyes with protective glasses Avoid inhaling the acid fumes The battery acid is extremely corrosive 10 ENGLISH Do not tip the battery enou
7. e of the engine machine seen from rear Let the oil run out into a collection vessel Then take the oil to a recycling station Avoid spilling oil on the V belts Screw tight the oil drain plug Take out the oil dipstick and fill up with new oil to the FULL mark Oil capacity Master 1 1 litre Senator Comfort President 1 4 litre Oil type summertime gt 4 C SAE 30 SAE 10W 30 can also be used The oil consump tion may increase somewhat if 10W 30 is used Check the oil level more regularly if this type of oil is used Oil type winter lt 4 C SAE 5W 30 if this oil is not available use SAE 10W 30 Do not use any additives with the oil Do not overfill This can result in the engine over heating CHANGING THE OIL Royal Change the engine oil for the first time after 20 hours of operation or during the first month and then after every 100 hours of operation or every 6 months Change the oil when the engine is warm Use a good grade of oil service grade SF SG or SH ENGLISH The engine oil may be very hot if it is drained off directly after switching off the engine For this reason allow the en gine to cool for a few minutes before draining the oil A Unscrew the oil drain plug in the end of the tube fig 11 Let the oil run out into a collection vessel Then take the oil to a recycling station Avoid spilling oil on the V belts Screw tight the oil drain plug
8. g ing gear NOTE Make sure that the machine is standing completely still before changing from reverse to forward gear or vice versa If a gear does not en gage immediately release the clutch and then press it in again Engage the gear again Never force a gear in 8 POWER TAKE OFF Switch for engaging and disengaging the electro magnetic power take off for driving front mounted accessories Two positions a I Press in the right side of the switch the power take off engages The symbol lights up 2 Press in the left part of the switch the power take off disengages 9 DISENGAGING LEVER President Royal Lever for disengaging the var able transmission Enables the machine to be moved by hand without using the engine Two positions 1 Lever pressed in the trans mission is engaged for normal BABS 2 Lever pulled out the trans mission 1s disengaged The ma chine can be moved by hand The machine must not be towed long distances or at high speed This can damage the transmission AREAS OF USE The machine must only be used for the following tasks with the indicated STIGA original accessories 1 Mowing With mower deck 13 2929 92M or 13 2930 107M 2 Grass clippings and leaves collection With towed collector 13 1978 30 or 13 1950 42 3 Grass and leaves transport With dump cart 13 1979 Standard 13 1988 Maxi or 13 1992 Combi ENGLISH The towin
9. g unit must only be loaded with a verti cal force of max 100 N The pulling force on the tow unit from towed ac cessories must be max 500 N NOTE Before using a trailer contact your insur ance company NOTE This machine is not intended to be driven on public roads STARTING AND OPERATING ENGINE CASING The engine casing must be removed to inspect and maintain the engine and battery Removing 1 Lift up the two catches on the rear edge fig 4 2 First pull the engine casing backwards slightly Then lift it off Fitting 1 Tilt the seat forward 2 Align the casing s top front pegs to the recesses in the front of the engine casing fig 5 Do not push the pegs in yet see item 4 below 3 Place the casing s bottom pegs in the groove in the shock absorber 4 Guide in the two side pegs in the groove in the front engine casing Now press forward the complete casing 5 Finally push down the two catches The machine must not used without the A engine casing fitted Risk for burn inju ries and pinch injuries FILLING THE FUEL TANK Always use clean unleaded petrol Never use oil mixed 2 stroke petrol fig 6 NOTE Bear in mind that standard unleaded petrol is perishable Never purchase more than what you can use within 30 days Environmentally friendly petrol is a good choice of petrol This type of petrol has a composition that is less hazardous for people and nature rol in specia
10. gh for bat tery acid to run out onto your hands and clothing If this should happen flush with lots of water A If the battery terminals are coated with oxide they should be cleaned Clean the battery terminals with a wire brush and grease them LUBRICATION CHASSIS The machine has three grease nipples on the rear axle which should be lubricated with universal grease after every 25 operating hours fig 17 Lubricate the steering cables with universal grease a couple of times per season Lubricate the plastic bearings with universal grease a couple of times per season Lubricate the tension arms joints with engine oil a couple of times per season Drop a little engine oil in both ends of the throttle control cable a couple of times per season Master Senator Comfort The transmission is filled with oil SAE 80W 90 on delivery from the factory If it is not opened which must only be done by a specialist it should not normally need topping up with oil STEERING CABLES Adjust the steering cables for the first time after 2 3 hours of operation and then after every 25 hours of operation Tension the steering cables by tightening up the nuts fig 18 Important The screw ends of the steering cables should be held firmly during the adjustment so that the cables are not twisted Use an adjustable wrench or the like inserting it in the key handles in the ends of the screws Tension the cables u
11. lly made containers for this Petrol is highly inflammable Store pet purpose Only fill up with petrol outdoors and A never smoke when filling Fill up with petrol before starting the engine Never remove the filler cap or fill up with pet rol when the engine is running or still warm Never completely fill the fuel tank Leave an emp ty space at least the entire filler tube plus 1 2 cm at the top of the tank to allow the petrol to ex pand when it warms up without overflowing CHECKING THE OIL LEVEL Master Senator Comfort Presi dent On delivery the crankcase is filled with SAE 30 oil Check the oil level every time before using to ensure that it is correct The machine should be standing on level ground QT Wipe clean round the oil dipstick Release it and pull out Wipe push down fully and screw it back in Unscrew it and pull out again Check the oil level Top up with oil to the FULL mark if the oil level 1s below this fig 7 CHECKING THE OIL LEVEL Royal On delivery the crankcase is filled with SAE oil 10W 40 Check the oil level every time before using to ensure that it is correct The machine should be standing on level ground E Wipe clean round the oil dipstick Release it and pull out Wipe push down fully without screwing it back in Pull out again and check the oil level Top up with oil to the FULL mark if the oil level s below this fig 8 SAFET
12. ntil they are no longer slack Do not tension the cables too hard This can cause unnecessary wear on the steering cables and pul leys etc 11 PATENT PROTECTION OF DESIGNS This machine or parts thereof is protected by the following patents and protection of designs 990 1091 0 SE 9901730 3 SE SE00 00577 PCT SE00 00895 PCT 4 537 581 US 00 1080 SE STIGA reserves the right to modify the product without giving any prior notice
13. ry lift er will now be locked in the lift position To lower the accessory press the pedal to release the lock Lower the accessory lifter to working po sition by slowly lifting your foot from the pedal 2A SERVICE BRAKE CLUTCH Master Senator Comfort Pedal which combines both the service brake and clutch Three positions t I Pedal released forward drive SY engaged The machine starts to ft move if a gear is engaged The Q service brake is not activated 2 Pedal pressed halfway down front drive disengaged it is not possible to change gear The service brake is not activated 3 Pedal pressed fully down front drive disengaged The serv ice brake is fully activated NOTE Do not regulate the speed by slipping the clutch Use a suitable gear instead to obtain the right speed 2B SERVICE BRAKE President Royal Pedal which activates the machine s brake system Three positions t I Pedal released forward drive 6 SY not engaged O s 2 Pedal pressed halfway front drive disengaged The service brake is not activated 3 Pedal pressed fully down front drive disengaged The serv ice brake is fully activated 3 PARKING BRAKE Inhibitor to lock the brake pedal in depressed posi tion Yo Press down the brake pedal fully Move P the inhibitor to the right and then release the brake pedal The parking brake is released by pressing the brake pedal The
14. spring loaded inhibitor slides to one side ENGLISH Make sure that the parking brake is released when driving 4 DRIVE PEDAL President Royal Pedal which activates the variable transmission 4 l Press down the pedal with the O ball of your foot the machine A moves forwards FA C 2 No pressure on pedal the 4 machine is stationary gt O 3 Press down the pedal with your heel the machine reverses The speed is regulated with the drive pedal The more pressure applied on the pedal the faster the machine goes 5 THROTTLE CHOKE CONTROL Control for setting the engine speed and to choke the engine for cold start 1 Choke for starting a cold engine The choke 1s located in the top of the groove 2 Full throttle when the machine is in K operation full throttle should always be used la 3 Idling 6 IGNITION LOCK Ignition lock used to start and stop the engine Four positions 1 Stop position the engine is short circuited The key can be removed 2 3 Operating position 4 Start position the electric start motor is activated when the key is turned to the spring loaded start position Once the en gine has started let the key return to oper ating position 2 3 7 GEAR LEVER Master Senator Comfort Lever for selecting one of five forward gears in the gearbox 1 2 3 4 5 neutral N or reverse R The clutch pedal must be depressed when chan
15. the machine from tipping over forwards The machine equipped with original accessories must not be driven in any direction on slopes with a gradient of more than 10 Reduce speed on slopes and when mak ing sharp turns to prevent the machine from tipping over and to make sure you do not loose control of the machine Do not turn the steering wheel to full lock when driving in top gear and at full throttle The machine can tip over Keep hands and fingers away from the seat mounting Risk of pinch injuries Never operate the machine without the engine casing Never drive with the mower deck en gaged and lifted up This will damage the drive belt to the unit gt rer Pr gt ENGLISH SERVICE AND MAINTENANCE SERVICE PROGRAMME STIGA s Service Programme should be followed to keep the machine in good condition in terms of reliability and operational safety and from an en vironmental perspective The contents of this programme can be found in the attached service log We recommend that an authorised workshop car ries out every service This guarantees that the work s carried out by trained personnel and with original spare parts The service log should be stamped at every serv ice A fully stamped service log is a valuable document that improves the machine s second hand value PREPARATIONS Unless otherwise stated all service and mainte nance should be performed when the machine is st
Download Pdf Manuals
Related Search