Star Micronics TCP100 Series Network Card User Manual
Contents
1. 6 Keep the TCP100 2000 reader writer away from corrosive gases flam mable gas chemicals or steams Exposure may cause generation of heat electric shock malfunction etc 7 Keep the TCP100 2000 reader writer away from magnetic sources to avoid erasing or damaging data stored on card 8 Do not use the power supply in the unspecified range This may cause generation of heat electric shock malfunction etc 9 Make sure that the power cable is plugged close enough to disconnect immediately when the unusual is found 10 Do not connect the AC power plug to the same outlet used for other electrical noise generation devises such as an electrical motor etc This may cause malfunction failure etc 11 Make sure that the power cable is plugged into the outlet certainly The earth terminal should be grounded to avoid electric shock failure etc 12 Provide enough room around the TCP100 2000 reader writer If not it may cause generation of heat malfunction failure etc 13 Do not leave the cleaning liquid in direct sunshine or near a source of heat such as fire or stove It may cause generation of heat which can bring skin burn etc 14 Do not drink or drop in your eyes the cleaning liquid It may cause damage to your body 15 Keep the cleaning liquid away from hands of the children During the operation 1 Do not use any other card but specified by Star Micronics Co Ltd It may cause malfunction failure etc 2 Do not u2. while holding the plug Do not put any heavy objects on the power cable Stop using the cable immediately if any damage or deformation is found on it Contact our sales tech support team for repair 12 Disconnect the power cable from socket if the TCP100 2000 reader writer is not used for long time 13 Do not use the TCP100 2000 reader writer when the environment such as temperature humidity changes drastically It may cause dew con densation which can bring malfunction etc Leave the TCP100 2000 reader writer in the new environment at least for one hour before re start 14 Do not use the TCP100 2000 reader writer under dew condensation It may cause malfunction failure electric shock etc 15 Clean the TCP100 2000 reader writer everyday in order to maintain the reliability No cleaning may cause error operation Refer to Chapter 6 CLEANING 16 Do not disassemble modify and repair the TCP100 2000 reader writer by yourself It may cause malfunction failure injury etc Contact our sales tech support team for repair 17 Do not leave the card in direct sunshine or a fluorescent light for long time as the card surface may get discolored 18 Incase the printed context is erased It can be reprinted if the data in the magnetic stripe remains 19 If the card gets stained Unclean or oily card lowers the read write and print quality In such a case please clean the card and the unit For the cleaning of the unit refer to
3. CLEANING 6 1 Using the cleaning card Two cleaning cards and one bottle of cleaning liquid for cleaning the mag netic head rollers etc are supplied in the enclosed plastic bag 1 Dimensions of cleaning card Felt surface EN 22 0 54 0 Es Felt surface l 85 6 i 89 6 2 Frequency of cleaning Unit mm 1 Daily or every 300 times of printing 2 When read write errors occur continuously or print quality gets low 3 How to use 1 Open the Front Cover and push the Cleaning Switch 2 Apply penetration of the cleaning liquid to the felt surfaces both sides of the cleaning card 3 Insert the cleaning card from the card slot 4 Allow the system approximately 1 minute for drying 5 Ethel alcohol solvent may also be applied for cleaning IMPORTANT osoeeveeeeree eee eee eee we we we we eee ee o Do not use the bent cleaning card Bent card will cause a card jam Cleaning switch Se Front cover 8 TROUBLE SHOOTING Difficulties when the power is turned ON Symptom Possible cause Remedy Power cable is not properly Properly plug in power Power Card is not plugged in cable LED lamp accepted Power cable is broken does Power fuse is blown notlight up Card is LED indicators are broken Consult technical accepted support Card is not Trouble with the main unit accepted Card is Card failure Power accepted Fla
4. Chapter 6 CLEANING 20 If you use continuously the same card please leave at least 3 minute intervals It is not necessary in the general operation using different cards one after another 2 OUTLINE The TCP100 2000 series is a reading writing device for specified IC card or reading device for ISO magnetic stripe type card It also has print erase capability to human readable area on the surface of the card This series is compatible with most host computers and various P O S systems TCP2000 series does not support for IC card The main features of the TCP100 2000 series are as follows 1 Reads writes data from to a magnetic stripe on the card depends on the model type 2 Reads writes data from to IC chip on the card TCP100 series only depends on the model type 3 Prints erases characters graphics to from a human readable area 4 Serial interface of RS 232C housed unit or CMOS mechanism unit 5 The human readable area of the card may be re used up to approx 500 times under the proper condition Model Name TCP110ZD Magnetic stripe read write 3 lines human readable printing upper part of a card Housed unit TCP192TD Specified IC card read write 3 lines human readable printing lower part of a card Housed unit TCP2000ZD Magnetic stripe read write Human readable wide printing on PET card Housed unit 3 UNPACKING After unpacking the unit check that all the accessories
5. SUAI THERMAL REWRITE CARD READER WRITER TCP100 2000 series Installation Guide amp Specifications Thank you for choosing the TCP100 2000 Thermal rewrite card system This Installation Guide amp Specifications includes very important instructions for safety Please read this manual before you start the system and follow the instructions Star Micronics Co Ltd Special Products Operating Division A AT ES 1 HANDLING NOTES 200 oe ee 1 MS ee a ae ee 4 UNPACKING Saue o ee ea a Eat ol 5 4 APPEARANCE AND NOMENCLATURE 6 5 CONNECTION TO EXTERNAL UNITS AND SETTING 7 P GUEANING oertein ree 8 TROUBLESHOOTING r riara E ee eee 9 8 GENERAL SPECIFICATIONS id ii 10 1 HANDLING NOTES At the installation 1 Install the TCP 100 2000 reader writer on a flat surface Minimize any shock or vibration to the reader writer as shock or vibration may cause injury and or failure 2 Keep the TCP100 2000 reader writer away from hands of the children 3 Do not use or leave the TCP100 2000 reader writer in direct sunshine or near a source of heat such as fire or stove It may cause generation of heat which can bring failure malfunction skin burn etc 4 Keep the TCP100 2000 reader writer away from liquids such as water oil etc Do not use or leave TCP100 2000 reader writer in high humid ity 5 Keep the TCP100 2000 reader writer away from dust metal powder etc
6. are included in the individual box Housed unit TCP100 2000 series TCP100 2000 unit Power cable Cleaning cards 2 pcs Cleaning liquid Installation Guide amp Specifications this manual 4 APPEARANCE AND NOMENCLATURE Housed unit TCP100 2000 series Switch Cover Power Switch POWER LED READY LED OK LED ERROR LED TCP100 TCP2000 back This cover protects the power switch of the system Push to open and close This switch turns the power of the system ON OFF This LED indicates that the power of the system is on This LED indicates that the card processing is ready This LED indicates that the card has been processed without error This LED indicates that the card has not been read due to an error e g jamming of the card in the reader writer RS232C Serial Connector This connector interfaces the connection between host AC Power Inlet Cleaning Button Modular Connector computers and the reader writer Connect this inlet to the power source with the attached AC power cable Push this button under the power ON condition then insert the cleaning card which is soaked with the clean ing liquid This interfaces the connection between MCD2000 Star original numerical key pad 9 Interface convert switch This switch changes the available interface RS232C right side or modular connector left side IMPORTANT e ee ee ee ee we
7. font Alpha numeric standard Chinese characters opti on Graphics Font configuration dots 12x24 24x24 48x24 24x48 48x24 12x24 24x24 48x24 24x48 48x48 8x16 16x16 32x16 16x32 32x32 Dot pitch 0 1mm Vertically 0 125mm Vertically 0 1mm Horizontally 0 121mm Horizontally Environment Installation place Indoor condition Operating temperature 5 to 35 C 20 to 80 RH no condensation and humidity Storage temperature 30 to 65 C 20 to 90 RH no condensation and humidity Vibration 1 5G 7 to 100Hz XYZ direction each 1hr resistance when packed Reliability Unit service life 300 000 times under proper condition Applicable card Specified thermal rewrite card Power supply AC100V 120V 230V 50 60Hz depends on the destination Interface RS232C D sub 9 pin Weight Approx 3 3Kg Approx 3 5Kg Dimension 110 W x143 H x308 D mm 110 W x143 H x326 D mm 10 SLI STAR MICRONICS CO UD Special Products Operating Div Card System Sales Section 536 Nanatsushinya Shimizu 424 0066 Japan Tel 81 543 47 0122 Fax 81 543 48 5013 http www star micronics co jp 2000 07 59082055
8. se wet or oily stained card Do not touch card with wet or stained hand It may cause malfunction failure etc If the card gets stained please perform cleaning of the card and the unit For the clean ing of the unit refer to Chapter 6 CLEANING 3 Keep the card away from magnetic source such as magnet speaker TV etc The data on the card may be damaged or erased 4 Do not leave the card in high temperatures such as inside of the car It may cause the bend of card or erase the printed data on the card 5 Do not insert bent card into the TCP100 2000 reader writer It may cause the card jamming 6 Do not insert the card in the unspecified direction It may cause mal function lt Specified Direction gt TCP110 TCP192 TCP2000 7 Do not insert any other object into the TCP100 2000 reader writer but the specified card It may cause failure electric shock etc 8 Do not interrupt the card feeding procedure inserting discharging It may cause malfunction or injury 9 Do not turn off the power during the card processing It may cause the damage or erase the data on the card 10 When the unusual such as noise stench smoke fire etc is found turn off the power immediately Then disconnect the plug If the TCP100 2000 reader writer being kept using it may cause failure skin burn etc Contact our sales tech support team for repair 11 Connect and disconnect the power cable only with power turned off and
9. w or bend of card Use applicable card LED lamp but main loss of card data light up unit does using other user s card not Head is stained Clean the head with properly cleaning card run System does not properly run Consult technical Trouble with the main unit support Difficulties during the operation Symptom Possible cause Remedy Card is not ejected Card jamming Reset the power Read write error Card is not applicable Using other user s card Use applicable card Card data is erased by a magnetized source Card is bent Card has flaws Issue new card Head is stained Clean the head with cleaning card GENERAL SPECIFICATIONS TCP100 TCP2000 Card type PVC thick card PET thin card Card feeding part Driving method Feed roller Card inserting direction Face up in one direction Card feed speed 350mm s high speed 40mm s low speed 350mm s high speed 30mm s low speed Magnetic recording part ISO Track 1 2 read Track 3 read write ISO Track1 Track2 Track 3 read write IC recording part Physical 1507816 1 compatible Characteristics Size 1507816 2 compatible Signal protocol Consult your supplier to check the applicable IC chip manufacturer and model name Printing part Printed characters 24 charactersx3 lines 20 charactersx13 lines 480x320 dots Character
10. we we ee 0 0 0 0 0 A three terminal earth grounded power supply cable is attached to TCP100 2000 housed unit For safety do not remove the ground pin 6 5 CONNECTION TO EXTERNAL UNITS AND SETTING Housed unit TCP100 2000 series lt Connecting the interface cable gt Turn OFF the power of the host computer and the reader writer Plug in an end of the interface cable to the reader writer connector and the other end to the serial port of the host computer Fasten two screws located at both the shoulders of the interface cable connectors Modular connector Connects to Star original stand alone terminal MCD2000 by specified cable Please set the interface convert switch to the left side Note Do not connect to any external devices other than MCD2000 TCP100 lt Serial Interface RS 232C gt Applicable connector D sub 9 pin female 2 Mating connector D sub 9 pin male 3 Connector terminals See the table below I O circuit See the table below Level RS232C Cable Cross reverse cable Pin No Signal name Direction Function 2 RXD IN Received data 3 TXD OUT Transmitted data 4 DTR OUT Data terminal ready always ON after reset 5 S GND E Signal ground 6 CTS DSR IN Clear to send Data set ready no detection 7 RTS OUT Request to send always ON after reset CTS is assigned to pin 8 at TCP2000 no detection 6
Download Pdf Manuals
Related Search