Snapper SPV21675EFC (7800266), SPV21675FC (7800265) Lawn Mower User Manual
Contents
1. 7 Installing the Discharge Deflector 8 Removing the Recycling Plug seana cece eee cette teens 8 Installing the Grass Bag 8 Maintenance iee erioa luu ee ee ee ee ee eee ee 9 Change Engine Re rb ed ew em ED eva Gade EH 9 Check Mower Blade 9 Check Engine Drive Belt 9 Service II mn 9 eter bie oe 9 A EITEN 9 San ote Bane ed tete Sea Rant cd IS cc Rd cus 9 Engine Ol ue mh a e SR ARDOR Oe e ORE mame ats 9 Wheel Drive Components 10 Storage Procedure iu ien he RR bed weds Hecht gad data tas 10 Mower Blade Replacement neran adean eens 11 Blade Sharpening euer le hee ae Ce hes Cae sie 11 Wheel Drive Control 12 Belt Ser icg sexe ee anc rre pee aah bebe dose 13 Engine Drive Belt Replacement 13 B ltery SarviCe eset Ree e Res ere Rer 14 Rear Cover Removal amp Installation 15 Service Schedule 0 ccc cece teen IH 16 Tro bleshooting esce Soe aa ee ret eee n 17 Warra2. Build up of debris on or around wheel drive omponents Clean debris place 17 Transmission cable adjustment required 2 Adjust transmission cable Drive belt requires replacement 3 Replace drive belt 4 Damaged transmission 4 Contact authorized SNAPPER dealer Transmission Noise Transmission cable adjustment required 1 Adjust transmission cable 2 Damaged transmission 2 Contact authorized SNAPPER dealer Ground Speed T Build up of debris on or around wheel drive Clean debris Too Fast Too Slow ponto components Unable to Adjust Transmission cable adjustment required 2 Adjust transmission cable Ground Speed Drive belt requires replacement 3 Replace drive belt 4 Damaged transmission 4 Contact authorized SNAPPER dealer utting Grass Improperly T Cutting height too low or high 1 Adjust cutting height 2 Forward speed too fast 2 Adjust to a slower speed 3 B Cutting blade dull or damaged 3 Sharpen cutting edges or replace blade Poor Grass Discharge Forward speed too fast T Adjust to a slower speed 2 2 Grass is wet 2 Mow when grass is dry Excessively worn or damaged blade 3 Service mower blade 4 Build up of grass clippings and debris under Clean deck eck E Improper blade installed on deck 5 Install proper SNAPPER blade 6 Blade installed improperly on deck 6
3. Install blade properly Oil Leaking T Leaking engine case 1 Contact authorized SNAPPER dealer 2 Check and tighten drain plug 3 Make sure dip stick or oil filler cap is securely in Warranties SNAPPER 2 YEAR LIMITED WARRANTY For two 2 years from purchase date for the original purchaser s residential non commercial use SNAPPER through any authorized SNAPPER dealer will replace free of charge except for taxes where applicable any part or parts found upon examination by the factory at McDonough Georgia to be defective in material or workmanship or both For ninety 90 days from purchase date for the original purchaser s commercial rental or other non residential use SNAP PER through any authorized SNAPPER dealer will replace free of charge any part or parts found upon examination by the factory at McDonough Georgia to be defective in material or workmanship or both All transportation costs incurred by the purchaser in submitting material to an authorized SNAPPER dealer for replacement under this warranty must be paid by the purchaser This warranty does not apply to certain transmissions to engines and their components and batteries as these items are war ranted separately This warranty does not apply to parts that have been damaged by accident alteration abuse improper lubrication normal wear or other cause beyond the control of SNAPPER This warranty does not cover any machine or com ponent
4. damaged 9 Protect yourself when mowing and wear safety glasses long pants and substantial footwear DO NOT mow barefooted or with sandals 10 Know how to STOP blade and engine quickly in preparation for emergencies 11 Use extra care when loading or unloading the machine into a trailer or truck 12 Check grass catcher components frequently for signs of wear or deterioration and replace as needed to prevent injury from thrown objects going through weak or torn spots SAFE HANDLING OF GASOLINE To avoid personal injury or property damage use extreme care in handling gasoline Gasoline is extremely flammable and the vapors are explosive 1 Extinguish all cigarettes cigars pipes and other sources of ignition 2 Use only an approved fuel container 3 DO NOT remove fuel cap or add fuel with the engine running Allow the engine to cool before refueling 4 DO NOT refuel the machine indoors 5 DO NOT store the machine or fuel container inside where there is an open flame spark or pilot light such as on a water heater or other appliances 6 DO NOT fill fuel containers inside a vehicle or on a truck or trailer bed with a plastic liner Always place the containers on the ground away from the vehicle before filling www snapper com IMPORTANT OPERATOR SAFETY INSTRUCTIONS Continued SAFE HANDLING OF GASOLINE Continued From Previous Page 7 Remove gas powered equipment from the vehicle or trailer and refuel it on the ground If
5. Change Page 9 X Periodic Oil Change Page 9 X Air Pre Cleaner Clean Sponge Element Engine Manual Air Cleaner Clean or Replace Engine Manual XEF Spark Plug Replace Engine Manual X Engine Cooling Clean Shroud amp Fins Engine Manual System Drive Belt Check for Wear and Page 9 13 X X X Tension Mower Blade Check for wear Damage Page 9 11 X amp Replacement Mower Deck Clean Debris Page 5 X Accumulation Wheel Drive Clean Debris Page TO X Components Accumulation Check for Wear or Damage ransmission Cable Check amp Adjust Page 12 X X X Spring Adjustment Change oil every 25 hours when operating under heavy load or high temperatures Clean more often under dusty conditions or when air debris is present Maintenance Replacement Parts Blade Control Cable SPV216 Blade Control Cable SPV216 Wheel Drive Control Cable utter Blade Double Wave Drive Belt Parts Manual for onapper Variable Speed Walk Behind Mower 16 www snapper com Troubleshooting PROBABLE CAUSE CORRECTIVE ACTION Engine Will Not Start Using Recoil Starter Fuel tank empty Fill fuel tank with fresh fuel Engine needs priming Prime Check Engine Manual for Instructions Spark plug wire disconnected Place spark plug wire onto spark plug Engine Will Not Start Electric Start Models Fuel tank empty Fill fuel tank with fresh fuel Prime Check Engi
6. always mention the model and serial number A WARNING DO NOT attempt any maintenance adjustments or service with engine and blade running STOP engine and blade Disconnect spark plug wire and secure away from spark plug Engine and components are HOT Avoid serious burns allow sufficient time for all components to cool Wear heavy leather gloves when handling or working around cutting blades Blades are extremely sharp and can Cause severe injury Service After First 5 Hours Change Engine Oil 1 Refer to the Engine Manual for proper oil specifications procedures and proper service intervals 2 For the simplest cleanest oil change simply turn the mower on its side to drain the oil as shown Drain the oil through the dipstick tube A Figure 13 into a container Allow sufficient time for all the oil to drain Important Drain the fuel tank before tipping the machine DO NOT tip the machine with the carburetor or spark plug down Oil from the crankcase will saturate the air filter and cause the engine to be hard to start or not start at all If contamination does occur the air filter will have to be replaced TIP MOWER ON SIDE Figure 13 Draining the engine oil 3 Dispose of drain oil properly 4 Fill the engine with oil as specified in the Engine Manual Do Not overfill Check Mower Blade 1 Disconnect the spark plug wire and secure the end away from the plug 2 Tilt the mower up on its re
7. are HOT Avoid serious burns allow sufficient time for all components to cool Wear heavy leather gloves when handling or working around cutting blades Blades are extremely sharp and can Cause severe injury Wheel Drive Components 1 Remove the rear cover Refer to the Section entitled Rear Cover Removal amp Installation 2 Clean any debris buildup on or around the transmission axles idler pulleys belt etc as well as on the inside of the cover Check components for wear or damage Replace worn or damaged components immediately 3 Replace the rear cover Important DO NOT operate the mower without the rear cover securely in place Storage Procedure Refer to the Engine Owner s Manual for directions regarding engine storage preparations Prepare the mower for end of season storage as follows 1 Drain the fuel from the fuel tank and let the engine run until all fuel is out of the carburetor 2 Disconnect and remove the spark plug wire away from the spark plug before any other preparations are made 3 Tape all openings closed to prevent spraying water into the exhaust or air intakes during washing 4 Tilt the mower up on its rear wheels and thoroughly clean the underside of the deck Do not tilt the mower with the spark plug or carburetor down Scrape away any accumulation of grass with a putty knife and or wire brush 5 Lubricate all exposed metal with a light coating of oil to prevent corros
8. cutting height Adjust to the desired height Refer to the Section Cutting Height Adjustment 4 Check the engine oil and add oil as needed to bring the 2 level up to the full mark A Figure 2 Refer to the Engine Owner s Manual for oil specifications VLL Figure 3 Starting the mower Figure 2 Checking engine oil 5 Add fuel to the tank after pushing the mower outside where fumes can safely dissipate Fill the tank to 1 1 2 inches below the top of the filler neck to allow for fuel expansion Make sure the cap is tightened after fueling Refer to the Engine Owners Manual for fuel specifications 6 Clean the exterior surfaces of the cutting deck and engine of any accumulation of spilled fuel dirt grass oil etc Keep the engine air intake screen and cooling fins clear at all times 7 Perform battery service Refer to the Section Battery Service Operation Starting and Operation Continued Propelling the Mower 1 Start the engine Refer to the Section entitled Starting and Operation Engine and Blade 2 Begin squeezing the wheel drive control A Figure 4 back toward the handle to engage the wheel drive and propel the mower forward Forward speed can be increased by squeezing the wheel drive control further back toward the handle Figure 4 Wheel drive control Components removed for clarity Stopping 1 Stop forward motion of the mower b
9. part that has been altered or modified changing safety performance or durability Batteries have a one 1 year warranty period with free replacement if required for one 1 year from the original purchase date SNAPPER will not be responsible for any installation cost incurred The battery warranty only covers original equipment batteries and does not cover damage to the battery or machine caused by neglect or abuse destruction by fire explosion freezing overcharging improper maintenance or use of improper electrolyte There is no other express warranty DISCLAIMER OF WARRANTY Implied warranties including those of merchantability and fitness for a particular purpose are limited to two 2 years from purchase date for the original purchaser s residential or other non commercial use and ninety 90 days from pur chase for the original purchaser s commercial rental or other non residential use and to the extent permitted by law any and all implied warranties are excluded This is the exclusive remedy Liabilities for consequential damages under any and all warranties are excluded Some states do not allow limitations on how long an implied warranty lasts or do not allow the exclusion or limitation of incidental or consequential damages so the above limitation or exclusion may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state WARNING THE USE OF REP
10. the battery harness connector B WARNING Shield the positive terminal with terminal cover located on battery harness This prevents metal from touching the positive terminal which could cause sparks Battery Service 1 Test the battery Refer to the Section entitled Battery Testing If the battery needs charging charge the battery Refer to the Section entitled Battery Charging 3 If the battery will not accept a charge or is partially charged after charging per instructions replace with a new battery Battery Storage If the mower is to be stored out of season on its rear bumper it is recommended the battery be removed charged and stored 1 Remove the battery 2 Perform battery service Refer to the Section entitled Battery Service 3 Store the battery in an area away from the mower on a wood surface NOTE Do not store the battery on a concrete surface 14 Battery Testing Check the battery s state of charge using a voltmeter Remember to hook the positive lead to the battery s positive terminal and the negative lead to the negative terminal Check the reading against the chart below If the voltage reads less than 12 80 volts charge the battery Refer to the Section entitled Battery Charging Battery Condition State of Charge 10096 Charged 75 Charged Digital Voltmeter 12 80v 12 40v 12 10v 11 90v Less than 11 80v 50 Charged 2595 Charged 0 Charged Batt
11. this is not possible then refuel equipment using a portable container rather than a gasoline dispenser nozzle 8 DO NOT start gas powered equipment in enclosed vehicles or trailers 9 Keep the nozzle in contact with the rim of the fuel tank or container opening at all times until fueling is complete DO NOT use a nozzle lock open device 10 If fuel is spilled on clothing change clothing immediately 11 DO NOT overfill a fuel tank Replace fuel cap and tighten securely OPERATION 1 DO NOT put hands or feet near or under rotating parts Keep clear of discharge area while engine is running 2 STOP engine when crossing gravel drives walks or roads and under any conditions where thrown objects might be a hazard 3 Mow only in daylight or good artificial light 4 DO NOT operate mower while under the influence of alcohol or drugs 5 After striking a foreign object or if mower vibrates abnormally STOP the engine disconnect and secure spark plug wire Inspect the mower for any damage and repair the damage before starting 6 DO NOT mow near drop offs ditches or embankments Operator could lose footing or balance 7 STAY ALERT for holes and other hidden hazards Tall grass can hide obstacles Keep away from ditches washouts culverts fences and protruding objects 8 DO NOT mow on wet grass Always be sure of your footing Keep a firm hold on the handle and walk never run Slipping could cause injury 9 ALWAYS stay behi
12. when the lever is squeezed back toward the handlebar and should disengage the transmission when the lever is released Figure 18 Wheel drive controls Components removed for clarity If the transmission does not engage or disengage adjustment may be performed as follows 1 Remove the rear cover from the mower Refer to the section entitled Rear Cover Removal amp Installation 2 With the wheel drive control lever in the DISENGAGE position the spring A Figure 19 on the end of the wheel drive control cable should have no tension Measure the overall length of the unextended spring B KPA Figure 19 Measuring the disengaged transmission spring length 12 3 Fully engage the lever and measure the length of the extended spring The overall spring length should increase by 0 020 0 025 4 To adjust spring extension a Disengage the lever b Toincrease the extended spring length loosen the jam nut B Figure 20 and rotate the ferrule C below the adjustment turnbuckle A located on the lower end of the wheel drive control cable one half turn out from the turnbuckle Tighten the jam nut C To decrease the extended spring length loosen the jam nut and rotate the ferrule one half turn in toward the turnbuckle Tighten the jam nut 5 Engage the lever and recheck the extended spring length Repeat Step 4 as needed Figure 20 Adjusting the
13. LACEMENT PARTS OTHER THAN GENUINE SNAPPER PARTS MAY IMPAIR THE SAFETY OF SNAPPER PRODUCTS AND WILL VOID ANY LIABILITY AND WARRANTY BY SNAPPER ASSOCIATED WITH THE USE OF SUCH PARTS IMPORTANT Please fill out the attached SNAPPER Product Registration Card immediately and mail to Snapper s Product Registration Center P O Box 1379 McDonough Georgia 30253 18 www snapper com E SLOPE GUIDE 15 DEGRE SIGHT AND HOLD THIS GUIDE LEVEL WITH A VERTICAL TREE ES A CORNER OF A STRUCTURE A POWER LINE POLE OR A FENCE A CHES ree oe Mime Operate a walk behind mower across the face of slopes never up or down slopes Operate a riding mower up or down slopes never across the face of slopes bh 10 DEGREES 15 DEGREES 4 ADM Aue NP Pa APARE EE 5 aei On a riding mower to determine if a slope is safe to mow 1 disengage the blade s 2 put the unit in reverse and 3 try to back straight up the slope If you can back up the slope it is generally safe to mow However if you do not feel safe or if you are not completely sure use this guide and do not mow a slope that is greater than 15 degrees If the riding mower is used with a pull behind or rear mounted attachment do not operate the unit on a slope that is greater than 10 degrees A 15 degree slope is a hill that increases in height at approximately 2 5 feet in 10
14. Safety Instructions amp Operator s Manual for SNAPPER 21 VARIABLE SPEED REAR DISCHARGE WALK BEHIND MOWERS Models SPV21675FC 7800265 SPV21675EFC 7800266 NOTE Specifications are correct at time of printing a Actual sustained engine power will likely be lower due to operating limita further details nd are subject to change without notice tions and environmental factors Please refer to Engine Power Rating Information for SNAPP Manual No 7101688 Rev 4 7 2008 ER GA 30253 U S A TP 100 5387 WB N Thank You for purchasing this quality built Snapper mower We re pleased that you placed your confidence in the Snapper brand When operated and maintained according to the instructions in this manual your Snapper mower will provide many years of dependable service This manual contains safety information to make you aware of the hazards and risks associated with the machine and how to avoid them This machine is designed and intended only for finish cutting of established lawns and is not intended for any other purpose It is important that you read and understand these instructions thoroughly before attempting to start or operate this equipment Save these instructions for future reference PRODUCT REGISTRATION IMPORTANT KEEP THIS INFORMATION FOR YOUR PERSONAL RECORDS Complete the following information on your Snapper purchase Date of Purchase Retailer Retailer s Phone Numb
15. ar wheels for access to the blade cap screw A Figure 14 Do not tilt the mower with the spark plug or carburetor down Important Drain the fuel tank before tipping the mower DO NOT tip the machine with the carburetor or spark plug down Oil from the crankcase will saturate the air filter and cause the engine to be hard to start or not start at all If contamination does occur the air filter will have to be replaced Figure 14 Tightening the blade cap screw 3 Check the torque of the blade cap screw Recommended torque should be 40 ft Ibs 4 Check the blade for sharpness wear and damage Refer to the Section entitled Blade Wear Limits Check Engine Drive Belt 1 Visually check the engine drive belt for cracking fraying severed or exposed belt strands If worn or damaged replace the belt before operating the mower Service Periodic Perform all maintenance as described in the Service Schedule section of this manual Engine Service the engine according to the engine owner s manual Air Filter Refer to the engine owner s manual for service instructions Engine Oil Refer to the engine owner s manual for service instructions WARNING A DO NOT attempt any maintenance adjustments or service with engine and blade running STOP engine and blade Disconnect spark plug wire and secure away from spark plug Engine and components
16. at SNAPPER McDonough Georgia 30253 Phone 1 800 317 7833 PROTECTION FOR CHILDREN Tragic accidents can occur if the operator is not alert to the presence of children Children are often attracted to the machine and the mowing activity Never assume that children will remain where you last saw them 1 KEEP children out of the mowing area and under the watchful care of a responsible adult other than the operator 2 DO NOT allow children in yard when machine is operated and turn machine OFF if anyone enters the area 3 DO NOT allow pre teenage children to operate machine 4 ALLOW only responsible adults amp teenagers with mature judgment under close adult supervision to operate machine 5 DO NOT pull mower backwards unless absolutely necessary LOOK and SEE behind and down for children pets and hazards before and while backing 6 USE EXTRA CARE when approaching blind corners shrubs trees or other objects that may obscure vision SLOPE OPERATION 1 Slopes are a major factor related to slip and fall accidents which can result in severe injury All slopes require extra caution If you feel uneasy on a slope DO NOT mow it 2 Mow across slopes never up and down Exercise extreme CAUTION when changing directions on slopes DO NOT mow steep slopes or other areas where stability or traction is in doubt Refer to the Slope Guide at the back of this manual 3 Use extra care with grass catchers or other attachments these affect th
17. balance If necessary correct balance by grinding heavy end of blade Reinstall blade B Figure 16 Note the correct assembly order A Blade hub B Blade C Blade flange facing up D Cone washer concave side up E Capscrew Check torque of blade retaining cap screw Recommended torque should be 40 ft Ibs Blade Sharpening 1 Disconnect the spark plug wire and secure the end away from the plug 2 Tilt the mower up on its rear wheels Do not tilt the mower with the spark plug or carburetor down Important Drain the fuel tank before tipping the mower DO NOT tip the machine with the carburetor or spark plug down Oil from the crankcase will saturate the air filter and cause the engine to be hard to start or not start at all If contamination does occur the air filter will have to be replaced Do not sharpen beyond original lt cutting edge lt 22 28 End view of blade assembly Figure 17 Sharpening the mower blade 11 WARNING A A DO NOT attempt any maintenance adjustments or service with engine and blade running STOP engine and blade Disconnect spark plug wire and secure away from spark plug Engine and components are HOT Avoid serious burns allow sufficient time for all components to cool Wheel Drive Control Adjustment The wheel drive control lever A Figure 18 should engage the transmission
18. e and mower blade by releasing the blade control before adjusting cutting height 3 1 50 in 4 00 in Figure 7 Cutting height settings approximate Recycling Operation Note For best recycling results cut up to a maximum of 1 3 of grass blade length and recycle ONLY when grass is dry 1 Set the height adjustment lever in the highest cutting position Notch 9 Refer to the Section entitled Cutting Height Adjustment 2 Proceed mowing slowly If the grass is very dense lower the height adjustment lever one notch lower to improve recycling performance Installing the Discharge Deflector 1 Raise the recycling cover A Figure 8 Important The recycling cover should remain on the machine at all times Do not remove uoneiadg Figure 6 Adjusting cutting height Figure 8 Installing the discharge deflector 2 Install the deflector B to the deck under the recycling cover making sure that The tabs C hook under the pivot rod D The locking tab on the deck A Figure 9 goes through the slot in the deflector B 3 Lower the recycling cover against the deflector Operation with engine and blade running STOP engine and blade Disconnect spark plug wire and secure away from spark plug Engine and components are HOT Avoid serious burns allow sufficient time for all components to cool A WARNING A DO NOT attempt any
19. e handling and the stability of the machine PREPARATION 1 Read understand and follow instructions and warnings in this manual and on the mower engine and attachments Know the controls and the proper use of the mower before starting 2 Only mature responsible persons shall operate the machine and only after proper instruction 3 Data indicates that operators age 60 and above are involved in a large percentage of mower related injuries These operators should evaluate their ability to operate the mower safely enough to protect themselves and others from serious injury 4 Handle fuel with extra care Fuels are flammable and vapors are explosive Use only an approved fuel container DO NOT remove fuel cap or add fuel with engine running PREPARATION Continued From Previous Column Add fuel outdoors only with engine stopped and cool Clean spilled fuel and oil from machine DO NOT smoke 5 Check the area to be mowed and remove all objects such as toys wire rocks limbs and other objects that could cause injury if thrown by blade or interfere with mowing Also note the location of holes stumps and other possible hazards 6 Keep people and pets out of the mowing area Immediately STOP Blade Stop engine and Stop mower if anyone enters the area 7 Check shields deflectors switches blade controls and other safety devices frequently for proper operation and location 8 Make sure all safety decals are clearly legible Replace if
20. er Equipment Model Number Serial Number Engine Model Type Trim It is very important that you register your purchase with Snapper to ensure warranty coverage Please mail your product registration card to Snapper at P O Box 1379 McDonough Georgia 30253 You can contact us at our website www snapper com or if you would like to speak with a Customer Service Representative call us at the Snapper Customer Relations Center at 1 800 317 7833 For faster service please have your Serial Number and Model Number available SNAPPER is a trademark of Briggs amp Stratton Yard Power Products Group Briggs amp Stratton Power Products Group LLC Copyright 2008 Briggs amp Stratton Corporation Jefferson WI USA Milwaukee WI USA All Rights Reserved Table of Contents Operator Safety ccc ci ik derek s ee ee ad dee eee es 2 Important Operator Safety Instructions 2 Features and Controls 4 a or pr Pee ta esee e Ee ER RI E inis 5 Pre Start Checklist 0 ccc cece cece teen Hn 5 Starting amp Stopping Engine amp 5 Propelliltg MOoWOr cx ces irte E Che RE hae RR e Ram Sida e 6 Handle Height Adjustment orisni ete 6 Cutting Height Adjustment 7 Recycling Operation
21. ery Charging To charge the battery 1 With the supplied DC charger Plug the charger connector into the battery harness connector B Figure 23 Plug the charger into a wall outlet and charge the battery for 48 hours Longer periods will not damage the battery Keep all sparks flame and fire away from area when charging battery or when handling battery Never use BOOST chargers on the battery www snapper com WARNING A DO NOT attempt any maintenance adjustments or service with engine and blade running STOP engine and blade Disconnect spark plug wire and secure away from spark plug Engine and components are HOT Avoid serious burns allow sufficient time for all components to cool Rear Cover Removal and Installation To Remove the Rear Cover 1 Remove the three fasteners A Figure 24 securing the rear apron to the machine 2 Remove the two fasteners B securing the rear cover to the machine 3 Slide the cover C down and out to remove Set all components aside To Install the Rear Cover 1 Reverse steps 1 3 above making sure the tab D on the rear cover is located on the outside of the machine Figure 24 Removing the rear cover 15 a2ueua urejA Service Schedule ITEM SERVICE REF EACH 5 25 50 100 EACH PERFORMED USE HRS HRS HRS HRS SEASON Engine Oil Check Oil Level Page 5 X Initial Oil
22. feet A 10 degree slope is a hill that increases in height at approximately 1 7 feet in 10 feet Use extreme care at all times and avoid sudden turns or maneuvers Follow other instructions in this manual for safety in mowing on slopes Operate a riding mower up or down slopes never across the face of slopes Operate a walk behind mower across the face of slopes never up or down slopes Use extra care when operating on or near slopes and obstructions CUT HERE TO USE SLOPE GUIDE 19 Notes 20 www snapper com Notes 21 SNAPPER 21 VARIABLE SPEED REAR DISCHARGE WALK BEHIND MOWERS Product Specifications All Common Service Parts Part Number Deck Size in 21 Blade Control Cable SPV21675FC 7101399 Height of Cut in 1 25 4 Blade Control Cable SPV21675EFC 7101400 Transmission Type Variable Speed Gear Wheel Drive Control Cable 7101398 Ground Speed mph 0 4 2 Cutter Blade Double Wave 7100242 Engine Power ft lbs 6 75 Drive Belt 7100883 Engine Displacement cc 190 Parts Manual 7102346 Fuel Tank Capacity qt 1 6 Engine Power Rating Information The gross power rating for individual gas engine models is labeled in accordance with SAE Society of Automotive Engineers code J1940 Small Engine Power amp Torque Rating Procedure and rating perform ance has been obta
23. ined and corrected in accordance with SAE J1995 Revision 2002 05 Torque values are derived at 3060 RPM horsepower values are derived at 3600 RPM Actual gross engine power will be lower and is affected by among other things ambient operating conditions and engine to engine variability Given both the wide array of products on which engines are placed and the variety of environmental issues applicable to operating the equipment the gas engine will not develop the rated gross power when used in a given piece of power equipment actual on site or net horsepower This difference is due to a variety of factors including but not limited to accessories air cleaner exhaust charging cooling carburetor fuel pump etc application limitations ambient operating conditions temperature humidity altitude and engine to engine variability Due to manufacturing and capacity limitations Briggs amp Stratton may substitute an engine of higher rated power for this Series engine SNAPPER Snapper Products 535 Macon Street McDonough GA 30253 1 800 317 7833 22 www snapper com
24. ion 6 Carefully fold the handles flexing the control cables to prevent cable damage 7 Store the mower in a shed or other dry area protected from weather 10 Wwww snapper com WARNING A DO NOT attempt any maintenance adjustments or service with engine and blade running STOP engine and blade Disconnect spark plug wire and secure away from spark plug Engine and components are HOT Avoid serious burns allow sufficient time for all components to cool Wear heavy leather gloves when handling or working around cutting blades Blades are extremely sharp and can cause severe injury Mower Blade Replacement Standard Blade Wear Limit 1 Inspect the blade Figure 15 frequently for signs of excessive wear or damage A New blade B Wear limit notch starts C Dangerous condition Do not use on the mower Replace with a new blade Figure 15 Mower blade wear limits WARNING A DO NOT use a Cutting blade that shows signs of excessive wear or damage Refer to the Section entitled MOWER BLADE REPLACEMENT for proper blade inspection and service procedures 3 Remove the blade B Figure 16 Make sure that blade hub is seated between flanges Figure 16 Removing the mower blade 4 Sharpen the blade on a grinding wheel at an angle of 22 to 28 degrees B Figure 17 DO NOT sharpen the blade beyond the original cutting edge A Check blade for
25. lade Note Recommended blade torque is 40 ft Ibs Figure 21 Removing the blade and belt cover Ou a2ueua urejA Figure 22 Removing the belt guide 13 WARNING A A DO NOT attempt any maintenance adjustments or service with engine and blade running STOP engine and blade Disconnect spark plug wire and secure away from spark plug Engine and components are HOT Avoid serious burns allow sufficient time for all components to cool Battery Service New Battery Preparation 1 Remove the battery from the carton 2 Place the battery in a well ventilated area on a level non concrete surface 3 Test the battery Refer to the Section entitled Battery Testing If the battery needs charging charge the battery Refer to the Section entitled Battery Charging 4 Connect the positive lead red first from the battery harness to the positive terminal on the battery using the bolt and nut plate supplied with the battery Connect the negative lead black last to the negative terminal on the battery using the bolt and nut plate Apply a small amount of grease over the terminals to prevent corrosion NOTE The battery may come with the harness already connected If so simply check to be sure the terminal hardware is securely tightened 5 Install the battery onto the power unit 6 Plug the main harness connector A Figure 23 into
26. maintenance adjustments or service Figure 9 Deflector locking tab Removing the Recycling Plug 1 Raise the rear discharge door A Figure 10 2 Remove the recycling plug B from the rear discharge chute Note The recycling plug should be removed only when bagging is desired and should be replaced as soon as bagging operations are completed Installing the Grass Bag 1 Raise the rear discharge door A Figure 11 2 Remove the recycling plug Refer to the section entitled Removing the Recycling Plug 3 Holding the grass bag handle B install the grass bag onto the back of the mower making sure that the grass bag hooks A Figure 12 are hooked onto the rear door pivot rod B Figure 11 Installing the grass bag Figure 12 Grass bag hooks Figure 10 Removing the recycling plug A WARNING A Grass Catcher bags used on SNAPPER products are made of woven fabric and are subject to deterioration and wear during normal usage Check condition of bag before each use Immediately replace worn or damaged catcher bags with only bags recommended by SNAPPER The grass catcher is optional equipment on some models www snapper com Maintenance Introduction To retain the quality of the mower use genuine SNAPPER replacement parts only Contact a local SNAPPER dealer for parts and service assistance For the correct part or information for a particular mower
27. nd handle when engine motor is running 10 DO NOT leave the machine with the engine running STOP BLADE and STOP ENGINE before leaving the operators position for any reason 11 Before cleaning repairing or inspecting make certain engine blade and all moving parts have STOPPED Disconnect and secure spark plug wire away from plug to prevent accidental starting 12 STOP engine and wait until the blade comes to complete STOP before removing grass bag and or clearing grass 13 DO NOT operate mower without the entire grass catcher or guards in place discharge guard rear guard or other safety devices in place and working DO NOT point discharge at people passing cars windows or doors S OPERATION 5 Continued From Previous Column S 14 DO NOT discharge material against a wall or obstruction Material may ricochet back towards the operator 15 Slow down before turning ae 16 Watch out for traffic when near or crossing roadways 17 DO NOT operate engine in enclosed areas Engine exhaust gases contain carbon monoxide a deadly poison 18 Only use accessories approved by the manufacturer See manufacturer s instructions for proper operation and installation of accessories MAINTENANCE AND STORAGE 1 DO NOT store mower or fuel container inside where fumes may reach an open flame spark or pilot light such as in a water heater furnace clothes dryer or other gas appliance Allow engine to cool before sto
28. ne Manual for Instructions Spark plug wire disconnected Place spark plug wire onto spark plug Wiring harness disconnected Connect wiring harness Battery dead Charge or replace battery Engine Stalls or Stops After Running 1 2 1 2 Engine needs priming 4 5 1 Blade control is released or is not being held Blade control should be held securely against andle at all times during operation of mower against handle Fuel tank empty Fill with fuel to proper level Engine air pre cleaner and or air cleaner dirty Clean free of all debris Spark plug defective or gap set improperly Service spark plug Water debris or stale fuel in fuel system Drain and clean fuel system Engine Loses Power Engine air pre cleaner or air cleaner dirty Clean or replace filters Spark plug faulty Service spark plug Drain and clean fuel system Excessive Vibration Damaged out of balance or bent mower blade Service mower blade Loose blade components Service and tighten loose parts Loose or missing air lift if equipped Replace air lifts Tighten to proper torque B 4 b 1 2 Water debris or stale fuel in fuel system 1 2 B 4 Lumpy or frayed belt 1 Replace belt GM OJ R3 San O1 Sans BJ 09 B3 Mower Will Not Move Loss Of Traction
29. nty sic eb sce a BE See eee ea 18 Slope Guides verges bloke be hed bee oA E 19 WARNING WARNING A Battery posts terminals and related accessories contain Engine exhaust some of its constituents and certain lead and lead compounds chemicals known to the State of vehicle components contain or emit chemicals known to California to cause cancer and birth defects or other the State of California to cause cancer or other reproductive reproductive harm Wash hands after handling harm pue saJnjeaJ Ayayes 10 0 funoousa qnoJ 39ueua ule A uone1ado uenem Operator Safety IMPORTANT OPERATOR SAFETY INSTRUCTIONS WARNING This powerful cutting machine is capable of amputating hands and feet and can throw objects that can cause injury and damage Failure to comply with the following SAFETY instructions could result in serious injury or death to the operator or other persons The owner of the machine must understand these instructions and must allow only persons who understand these instructions to operate machine Each person operating the machine must be of sound mind and body and must not be under the influence of any substance which might impair vision dexterity or judgment If you have any questions pertaining to your machine which your dealer cannot answer to your satisfaction call or write the Customer Service Department
30. ring machine in an enclosure Store fuel container out of reach of children in a well ventilated unoccupied building 2 Keep mower and engine free of grass leaves or excess grease to reduce fire hazard and engine overheating 3 When draining fuel tank drain fuel into an approved container outdoors and away from open flame 4 Keep all bolts especially blade bolts nuts and screws properly tight Check that all cotter pins are in proper position 5 Always provide adequate ventilation when running engine Engine exhaust gases contain carbon monoxide a deadly poison 6 Service engine and make adjustments only when engine is stopped Removed spark plug wire from spark plug and secure wire away from spark plug to prevent accidental starting 7 DO NOT change engine governor speed settings or overspeed engine 8 Check grass bag assembly frequently for wear or deterioration to avoid thrown objects and exposure to moving parts Replace with new bag if loose seams or tears are evident Replace slider or bag adapter if broken or cracked 9 Mower blades are sharp and can cut Wrap the blades or wear heavy leather gloves and use CAUTION when handling them 10 DO NOT test for spark by grounding spark plug next to spark plug hole spark plug could ignite gas exiting engine 11 Have machine serviced by an authorized SNAPPER dealer at least once a year and have the dealer install any new safety devices 12 Use only genuine SNAPPER replacement par
31. transmission spring tension IMPORTANT INCORRECT ADJUSTMENT CAN CAUSE PREMATURE WEAR AND OR DAMAGE TO THE WHEEL DRIVE COMPONENTS www snapper com WARNING A A DO NOT attempt any maintenance adjustments or service with engine and blade running STOP engine and blade Disconnect spark plug wire and secure away from spark plug Engine and components are HOT Avoid serious burns allow sufficient time for all components to cool Belt Service On self propelled mowers the engine belt transmits power from the engine to the transmission that powers the rear wheels Should the belt become worn it could cause slip page which would impair mower performance The condi tion of the engine belt should be checked after every 25 hours of mower operation Engine Drive Belt Replacement 1 Empty the fuel tank 2 Remove the blade A Figure 21 Refer to the Section entitled Blade Sharpening 3 Remove the hardware B securing the two piece belt cover beneath the deck Remove the cover 4 Remove the rear cover of the mower Refer to the Section entitled Rear Cover Removal amp Installation 5 To replace the belt a Remove the hardware B Figure 22 securing the belt guide A to the transmission assembly Remove the belt guide b Remove the belt from the transmission and engine pulleys noting the belt routing c Replace the belt d Replace the belt guide onto the transmission 6 Replace the covers and b
32. ts to assure that original standards are maintained Features and Controls IMPORTANT The figures and illustrations in this manual are provided for reference only and may differ from your specific model Contact your Snapper dealer if you have questions Features and Controls Oil Fill Cap Dipstick Fuel Filler Cap Recycling Cover Battery Box Height Adjustment Lever Blade Control Rope Start Handle Drive Wheel Control Rear Discharge Door Grass Bag gt www snapper com Pre Start Check List Starting and Operation Make the following checks and perform the service required Engine and Blade before each start up 1 Pull the blade control A Figure 3 against the handle 1 Check the guards deflectors grass bag and covers to 2 Start the mower make sure all are in place and securely tightened Manual Start Models Pull the rope start handle B 2 Check the blade control A Figure 1 and wheel drive to crank the engine control B to insure they work freely Electric Start Models Insert the key C into the ignition switch D located on the right side of the handle above the rope guide Turn the key to crank the engine 3 After the engine starts allow a brief warm up until the engine runs smooth before beginning mower operation NOTE To stop the engine and blade release the blade control C Figure 1 Mower controls 3 Check the
33. y releasing the wheel drive control 2 Stop the engine and blade by releasing the blade control Handle Height Adjustment The height of the mower handle can be adjusted as follows 1 Turn the two locking cams A Figure 5 a quarter turn to unlock the handle assembly B 2 Align the handle assembly with one of the three handle height adjustment holes C in the mounting brackets 3 Return the locking cams to their original position to lock the handle Figure 5 Adjusting the handle height A WARNING A DO NOT attempt any maintenance adjustments or service with engine and blade running STOP engine and blade Disconnect spark plug wire and secure away from spark plug Engine and components are HOT Avoid serious burns allow sufficient time for all components to cool www snapper com WARNING A DO NOT attempt any maintenance adjustments or service with engine and blade running STOP engine and blade Disconnect spark plug wire and secure away from spark plug Engine and components are HOT Avoid serious burns allow sufficient time for all components to cool Cutting Height Adjustment 1 Pull the height adjusting lever A Figure 6 outward and move to the desired cutting height The highest cutting position is Notch 9 B also see Figure 7 The lowest cutting position is Notch 1 C Note The lever will set all wheels to the same cutting height A WARNING A Stop engin
Download Pdf Manuals
Related Search