Snapper Clean Sweep Triple Catcher Lawn Mower User Manual
Contents
1. 15 NOTE In these instructions left and right are referred to as seen from the operating position Safety Rules amp Information unit severe personal injury or death to you or bystanders or damage to property or equipment The trian Head these safety rules and follow them closely Failure to obey these rules could result in loss of control of gle in text signifies important cautions or warnings which must be followed GENERAL WARNINGS Know the unit s controls and how to stop quickly HEAD THE OPERATOR S MANUALS Head and obey all safety decals Only allow responsible adults who are familiar with the instructions to operate the unit Disengage the PTO Shut off the engine and wait for all moving parts to stop before attaching adjusting or disconnecting any part of the collection system Check the collection system to make sure it is bolted tightly to the unit DO NOT operate the unit without either the entire grass catcher or the deflector in place Turn off the PTO to disengage the blades when not mowing DO NOT mow in reverse Always look down and behind before and while travelling in reverse DO NOT turn sharply when travelling alongside a building or any object Slow down before turning DO NOT carry passengers When collection system is removed from the mower deck the deflector must be properly installed Collector bags are subject to deterioration and wear during normal use I2. Note The belt stop D Figures 7 amp 8 is located and ori ented differently in 44 and 50 applications For all applications when turbo is installed belt stop D should Spacer D Belt Stop be outside the belt 1 8 away from the backside of the B 5 16 Washers E Lockwasher C Capscrew 5 16 18 x 1 1 2 5 16 belt 44 Models A Spacer D Belt Stop B 5 16 Washers E Lockwasher C Capscrew 5 16 18 x 1 1 2 5 16 Figure 9 Install Idler Assembly A Idler Assembly B Belt Guide C Capscrew 5 16 18 x 7 8 D Locknuts 5 16 18 E Taptite Screws Install Idler Assembly amp Belt Guide 1 See Figure 9 Remove and discard the two taptite screws from locations E 2 Insert two 5 16 18 x 7 8 capscrews C through the mower deck and arbor Tighten the capscrews 3 Mount the idler pulley assembly A to the deck using the two 5 16 18x 7 8 capscrews C and 5 16 18 whi Zlock nuts D Install Turbo Drive Pulley 1 See Figure 10 Remove the arbor drive belt from the right side arbor pulley 2 Remove and discard the flange nut and spring wash ers securing the arbor pulley and spacer A Retain the pulley and spacer A 3 Install the new spacers B amp F turbo drive pulley C spring washer D and sleeve nut E Be sure the notches in the pulleys and spacers are aligned Install the spring washer concave side down Torque the sleeve nut to 55 70 ft 16 74 95 N m 4 Reinstall th
3. 10 32 x 1 2 capscrews washer J and 10 32 n nut Insert middle tube Secure the elbow to the turbo using clip M Clip M may need to be relocat 2 If not already done insert the upper tube G Figure ed to a different set of holes N to ensure secure fit 5 into the socket D Insert the tube from the front This will require some effort 1 Some 50 models covered by this manual require upper tube G Figure 6 to be shortened Shorten Note Use correct hole locations to maintain proper tube connections and prevent lower tube from disconnecting 3 Mount the socket D and deflector A to the back from the turbo 2 plate B using the four 5 16 18 x 1 capscrews C Initial Collector Assembly Figure 2 Install the Bags A Bags Figure 1 Assemble Catcher Bags B Back Plate A Clip E Clamp B Cloth Bag F Nut C 5 16 18 x 3 4 Carriage Bolt G Lockwasher D Hanger Bracket H Wire Hoop COLLECTOR ASSEMBLY Assemble Catcher Bags 1 See Figure 1 Insert the wire hoop H through the cloth bag B 2 Install the clamp E and hanger bracket D Secure with two 5 16 18 x 3 4 carriage bolts C lockwashers G and nuts F Install Cover 1 See Figure 2 Hook the bags A on the back plate B Note If desired the bags can be lined with 30 Figure 3 Install Cover gallon trash bags for easy disposal S sae C Hinges 2 See Figure 3 Set the cover A on
4. C Simplicity SNAPPER OO Nasser ATTACHMENT OPERATOR S MANUAL Clean Sweep Triple Catcher Clean Sweep Triple Catcher Mfg No Description Rev 00 THIS PAGE INTENTIONALLY BLANK FOR PLACEMENT ONLY DO NOT PRINT Safety Rules amp Information General Warnings eese eee 2 Safety Decals 2 General Operating Information Mowing with the Triple Catcher 3 Required 01 3 After Operation 3 Initial Turbo Installation Contents Turbo Installation Group 4 TUDO RR 5 Initial Counter Balance amp Front Weight Carrier Installation Counter Balance Installation 10 Install Front Weight Carrier 10 Initial Hitch amp Tube Installation Install Hitch Plate amp Back Plate 11 Install Tubes amp 12 Table of Contents Initial Collector Assembly Assemble Catcher Bags 13 Install COVES cccccecececececececececececececeteneaeaeass 13 Removing amp Re attaching the Triple Catcher Removing the Grass Catcher 14 Reattaching the Grass Catcher
5. top of the bags B and align the hinges C 3 See Figure 4 Install the hinge pins B through the the hinges C and secure with a hair pin clip D NOTE Push the hair pin clips all the way on or they will be bent by the hinge when the cover is opened CAUTION Before you begin operating the unit be certain you have read all of the safety and operational information of this instruction sheet as well as the Operator s Manual for the tractor and any other attachments Figure 4 Install Hinge Pins A Cover C Hinge B Hinge Pin D Hair Pin Clip 13 Removing amp Re attaching Grass Catcher Figure 1 Remove the Cover A Cover C Hinge B Hinge Pin D Hair Pin Clip Figure 3 Install Back Plate Flat Style Bumper shown A Back Plate amp Support C Hitch Plate B Hair Pin D Rod Figure 2 Remove the Bags A Bags REMOVING amp RE ATTACHING THE GRASS CATCHER Removing the Grass Catcher amp Tubes 1 Remove the hair pin clips D Figure 1 and hinge pins B and remove the cover A To Turbo 2 Remove the bags A Figure 2 by lifting them off their Blower hooks Empty any grass out the bags 3 Unclip middle and lower tube assembly B Figure 4 Figure 4 Assemble Tubes and remove from turbo and upper tube A Upper Tube C Clip B Middle amp Lower Tube 4 Warning Back plate A will fall when rod D is removed Remove the hair pin B Figure 3 and rod A WARNING D whi
6. Inc All Rights Reserved Printed in USA MASSEY FERGUSON LAWN amp GARDEN EQUIPMENT Simplicity Mfg Inc 500 N Spring Street PO Box 997 Port Washington WI 53074 0997 www MasseyLawn com
7. d e For added stability and to prevent tipping or loss of control a Use reduced speed on uneven ground and when turning corners b Reduce loads on hillsides It is recommended that the collection system be kept only half full when negotiating any slopes Start mowing on slopes when the collection system is empty c Mow up and down the face of slopes never across the face of any slope When operating on slopes use front counter weights Never operate on slopes greater than 17 6 10 These labels are easily applied and will act as a constant visual reminder to you and others who may use the equipment to follow the safety instructions necessary for safe effective operation ATTACHMENT DECALS This shield must be in place at all times during operation Do not open cover with engine running MT Do not operate mower without the complete catcher in place When operating on slopes refer to operator s manual for counterweights e Mower deflector must be in down position when blower is removed L a Decal WARNING Do Not Open Cover Part Number 1704405 Decal WARNING Part Number 1717291 Read and obey all operation and warning decals x Q LS 67 e 23 Al 22525222 ROLLI 22522223 02222 oe KY DO Q 232 25222 MOWING WITH THE CATCHER Always operate with throttle at full speed when mowing Grass should be cut often and not too short If grass is too lon
8. e arbor drive belt on the lower pulley Install Anchor Bracket 1 See Figure 12 If not already done assemble the anchor bracket and related components as shown in Figure 11 2 Attach the anchor bracket assembly B Figure 12 to the mower deck using 5 16 18 x 1 capscrews A and 5 16 18 locknuts C NOTE The deflector latch MUST secure the deflector in a down position as shown in Figure 7 Initial Turbo Installation Torque to 55 70 ft Ibs gt Original Pulley and Spacer Figure 10 Install Turbo Drive Pulley A Original Pulley amp Spacer D Spring Washer B Spacer W Notches New E Sleeve Nut C Pulley New F Spacer New Figure 11 Anchor Bracket Assembly A Anchor Bracket E Nut Hex 5 16 B Lockwasher 5 16 Large F Wing Nut 5 16 C Latch Spring G Locknut 5 16 D Lockwasher 5 16 Small H Capscrew 5 16 18 x 2 1 2 Figure 12 Anchor Bracket Installation A Capscrews 5 16 18 1 B Anchor Bracket C Locknut 5 16 18 Initial Turbo Installation Figure 13 Belt Cover Plates A Belt Cover Plate for 50 Mower B Belt Cover Plate for 44 Mower A WARNING When the turbo blower assembly is removed from the mower deck the deflector MUST be properly installed Install Belt Cover Plate 1 Attach the belt cover plate B Figure 14 to the sup port bracket E using a 5 16 18 x 1 capscrew C washer D and nylock nut F NOTE This cover plate must be able to piv
9. g or lush it may be necessary to keep ground speed to a minimum or to cut only half the width of the mower to prevent clogging If grass is long operate with mower in high cutting position for first pass cutting again in a lower position on a second pass Do not open the cover with mower engaged If a large amount of cut grass is spilling out from under deck the tube may be plugged or the bags may be full discontinue mowing stop the unit disengage the PTO shut off the engine and then empty the catcher or clear the tube WARNING ALWAYS shut off the tractor Disengage the PTO and allow all moving parts to stop BEFORE disconnecting or clearing tube or emptying catcher Before leaving the operator s position for any reason engage the parking brake disengage the PTO stop the engine and remove the key To reduce fire hazard keep the engine rider and mower free of grass leaves and excess grease Do not stop or park rider over dry leaves grass or combustible materials CAUTION Before you begin operating the unit be certain you have read all of the safety and operational information of this instruction sheet as well as the Operator s Manual for the tractor and any other attachments General Operating Instructions BEFORE OPERATION Clear the lawn of all sticks stones wire and other debris which may be caught or thrown by the mower blades Check grass condition If wet wait until later in the day If
10. grass is wet the grass catcher is likely to become plugged For efficient bagging air circulation under the mower deck through the chute and into the bag is very important For this reason BEFORE YOU BEGIN MOWING you should make certain the underside of the mower and the underside of the catcher lid are free from grass and debris Make sure that there is a snug fit between mower deck blower housing tubes and grass catcher cover REQUIRED ACCESSORIES A front mounted factory approved weight carrier and 66 Ibs worth of weights are required when using this rear mounted grass catcher Never operate on slopes greater than 17 6 10 AFTER OPERATION CAUTION Do not leave grass in bagger containers Empty containers after each use and before storing Failure to do so may result in spontaneous combustion which could develop into a fire Remove any debris from the the screen on the underside of the lid Note The lid screen can be partially removed for easier cleaning and should be cleaned regularly The blower housing and tube should be removed for cleaning Inspect the grass bags for wear or damage Make sure that there is a snug fit between mower deck blower housing tubes and grass catcher cover STORING THE GRASS CATCHER Clean the grass catcher thoroughly using a mild deter gent other products may damage the tube Remove any debris from the the screen on the underside of the lid If paint has been
11. he deck Discard the cover and bolts A 2 Remove and discard the plastic plugs from the deck at the locations used by bolts F amp B Figure 5 3 Slide the deflector rod D through the pivot bracket E 4 Secure the front of the pivot bracket with a 5 16 18 x 3 4 carriage bolt F and flange whizlock nut C Figure 5 Install Deflector Hinge 5 Secure the back of the pivot bracket E and belt Belt Cover Support F 5 16 18 x 3 4 cover support A with a 5 16 18 x 1 capscrew B 5 16 18 x 1 Capscrew Carriage Bolt 5 16 washer G and flange whizlock nut C 5 16 18 Whizlock Nuts G 5 16 Washer Deflector Support Rod Pivot Bracket Initial Turbo Installation Install Deflector 1 See Figure 6 Drill four 13 64 holes from the bottom of the deflector at the pre molded drill points A bot tom of deflector 2 Attach the deflector to the support rod wire form using four 10 14 x 3 4 truss head screws and nylock nuts Figure 6 Install Deflector A 13 64 Hole Locations C Screws 10 24 x 3 4 B Nylock Nuts Install Belt Guide 1 See Figure 7 amp 8 Locate the taptite screw that will 50 Models Ee be replaced by capscrew C Remove and discard XS the taptite screw 2 Assemble the 5 16 18 x 1 1 2 capscrew C lock Mad B washer E washers B belt stop D and spacer A 47 SN A 2 3 Secure the belt stop assembly to the deck in the loca tion shown
12. le holding back plate A 5 Lift the back plate and support assembly A Figure 3 OPERATION WITHOUT TURBO amp CATCHER en alten For operation without turbo the mower deflector MUST be properly installed in the down position and retained by the spring latch see turbo operator s manual 14 Removing and Re attaching Grass Catcher Figure 6 Bags A Bags B Back Plate Figure 5 Install Back Plate Flat Style Bumper shown A Back Plate amp Support C Hitch Plate B Hair Pin D Rod Re attaching the Grass Catcher 1 Set the back plate and support A Figure 5 onto pins of hitch plate C Secure with rod D and hair pin B 3 Hook the bags A Figure 6 on the back plate B 4 Install the catcher cover A Figure 7 amp 8 and secure with the hinge pins B and hair pin clips D NOTE Push the hair pin clips all the way on or they will be bent by the hinge when the cover is opened 5 Insert middle amp lower tube B Figure 4 into upper 23 7 Install Cover C Hi tube A and clip C onto turbo Bags Hinges Figure 8 Install Hinge Pins A Cover C Hinge B Hinge Pin D Hair Pin Clip 15 lt Simplicity MANUFACTURING INC 500 N Spring Street PO Box 997 Port Washington WI 53074 0997 www SimplicityMfg com SNAPPER Simplicity Mfg Inc Snapper Products 535 Macon Street McDonough GA 30253 www Snapper com Copyright 2006 Simplicity Manufacturing
13. n Existing Spacer Spring New Spring New Washer New Plate Spring Support New Spacer Existing Eyebolt Existing Washer Existing Capscrew Existing Nut Existing Mower Deck Figure 2 Front Weight Carrier Installation A Holes D Rod B Capscrews E Clips Safety 1 2 13 x 1 1 4 F Carrier Weight C Locknut 1 2 13 Front Weight Carrier Installation 1 Install carrier F as shown securing with 1 2 13 x 1 1 4 capscrews B and 1 2 13 locknuts C 2 Rod D and safety clip E are used to secure required weights Figure 1 Install Hitch Plate Flat Style Bumper A Hitch Plate D Locknuts 1 2 13 B Heat Shield E Upper amp Lower C Capscrews Hex Bumper 1 2 13 x 1 1 4 F existing Holes HITCH amp TUBE INSTALLATION Install Hitch Plate and Back Plate Flat Style Bumper 1 Remove and discard hardware holding heat shield B Figure 1 to upper and lower bumper E Open existing holes F in heat shield B and upper amp lower bumper E to 17 32 Install hitch plate A to upper and lower bumper E keeping heat shield B in between as shown Secure with 1 2 13 x 1 1 4 capscrews C and 1 2 13 locknuts Tube Style Bumper 1 Center the and secure hitch plate A Figure 2 to the bumper B with u bolts C and 3 8 16 locknuts D as shown All Style Bumpers 1 Install the cover plate F Figure 3 on the back plate A Sec
14. nspect the bag periodically for tears holes or weak spots and replace with a new bag that meets manufacturer s durability standards SAFETY DECALS This unit has been designed and manufactured to pro vide you with the safety and reliability you would expect from an industry leader in outdoor power equipment manufacturing Although reading this manual and the safety instructions it contains will provide you with the necessary basic knowledge to operate this equipment safely and effec tively we have placed several safety labels on the unit to remind you of this important information while you are operating your unit All DANGER WARNING CAUTION and instructional messages on your rider attachments and mower should be carefully read and obeyed Personal bodily injury can result when these instructions are not followed The information is for your safety and it is important The safety decals below are on your product If any decals are lost or damaged replace them at once See your local dealer for replacements TP 600 2562 01 AT SMA e f the mower stalls or the collector chute plugs 1 Disengage the PTO 2 Stop the engine and remove the key 3 Set the parking brake and wait for all moving parts to stop 4 Remove the foreign object or clear the chute with a piece of wood before restarting the engine NEVER place hands into COLLECTOR OR MOWER housing to clear jammed objects Blower OR MOWER may rotate when object is remove
15. ot on the support bracket Different belt covers are required for different applications Refer to Figure 13 2 Rotate the belt cover until the notch catches the idler assembly belt cover latch A Figure 14 Cover latch A may need to be rotated for proper alignment Install Turbo Belt 1 Locate the correct drive belt for your installation 44 models require drive belt 1705142 50 models require drive belt 1707956 the part number is stamped on the belt 2 Loosen the hardware securing the drive pulley belt guide B Figure 15 amp 16 and the idler pulley C 3 Install the drive belt as shown in Figures 15 amp 16 4 Tighten the hardware securing the drive pulley belt guide B and idler pulley C The idler belt guide should be within 1 16 of the belt Install Mounting Bracket 1 See Figures 15 amp 16 Locate and remove the two longer capscrews used to secure the rear of the turbo housing and idler spring anchor 2 Install the turbo mounting bracket A using the removed hardware Note that the bracket is mounted in two different positions depending on the applica tion Figure 14 Install Belt Cover Plate A Belt Cover Latch E Support Bracket B Belt Cover Plate F Nylock Nut 5 16 C Capscrew 5 16 18 x 1 D Washer 5 16 Figure 15 Belt Routing 44 Models A Mounting Bracket B Drive Pulley Belt Guide Hardware C Idler Pulley Hardware D Mounting Bracket Hardware Figure 16 Belt Rou
16. rs or other collection devices used in conjunction with this turbo blower Initial Turbo Installation Figure 17 Install Turbo Blower A Pivot Bracket B Deflector C Turbo D Anchor Bracket E Wing Nut Mower Deck Turbo Drive Pulley Mower Deck Arbor Pulley To Slacken FRONT Belt Turbo Drive Pulley Figure 19 Belt Cover A Belt Cover Plate B Belt Cover Latch Initial Counter Balance amp Weight Carrier Installation Figure 1 Counter Balance Installation COUNTER BALANCE amp WEIGHT CARRIER INSTALLATION Counter Balance Installation 1 Remove hair pin C Figure 1 from trunnion B Remove trunnion B from rear deck lift lever A Mark or measure trunnion position on rear deck lift lever Remove trunnion B from eyebolt 1 Remove capscrew K washer J eyebolt I spacer H and nut L from mower deck M Thread eyebolt I through plate G as shown Attach capscrew washer J eyebolt 1 spacer H to mower deck M securing with nut L Slide washer F spring E and spacer D onto eyebolt I as shown Install trunnion B onto eyebolt 1 to position of mea surement or mark from step 1 Install trunnion B into rear deck lift lever A secure with hair pin C Check deck leveling as described in Operators Manual and make necessary adjustments 10 Rear Deck Lift Lever Trunnion Existing Hair Pi
17. scratched on metal parts touch up with paint or apply a thin film of oil to prevent corrosion otore in a dry area Dry thoroughly before storing for a long period of time Always store away from moisture Setup Initial Turbo Installation Torque to 55 70 ft Ibs 24 49 Nube 39 sion 25 29 uL 20 8J 21 O Existing Pulley amp Spacer 48 2 26 36 ge vA 37 99 38 6 gt Existing 2 Hardware gt A of m j ds 7 Existing Hardware Bolt Washer Lockwasher amp Nut 40 Existing Hardware Ref Qty Description 17 2 WASHER Flat 3 8 34 1 WASHER 3 8 1 2 CAPSCREW Hex Head 5 16 18 x 1 18 1 CAPSCREW Hex Head 3 8 16 x 2 35 1 V BELT 50 Turbo 2 06 WASHER 5 16 19 1 PULLEY ASSEMBLY Idler 36 1 NUT Hex Lock 5 16 18 3 1 SUPPORT Belt Cover 20 1 BELTSTOP 37 1 NUT Wing Special 5 16 4 4 Nylon Lock 10 24 21 1 CAPSCREW 5 16 18 x 1 1 2 38 2 Hex 5 16 18 5 1 ROD Deflector 22 LOCKWASHER 5 16 39 1 BRACKET Anchor 6 4 SCREW Truss Head 710 24 x 3 4 23 1 SPACER 40 1 CARRIAGE BOLT 5 16 18 7 1 PIVOT ASSEMBLY 24 1 NUT Sleeve 41 1 BRACKET ASSEMBLY Cutoff 8 4 Hex Whizlock 5 16 18 25 1 WASHER Belleville 42 1 SPACER 9 1 NUT Nylock Hex 5 16 18 26 1 PULLEY 43 1 BRACKET 10 1 COVER BELT 50 2 1 44 2 CAPSCREW Hex Head 5 16 18 x 7 8 11 1 DECAL Warning 28 1 PLATE Spring Support 45 1 CARRIAGE BOLT 5 16 18
18. ting 50 Models A Mounting Bracket B Drive Pulley Belt Guide Hardware C Idler Pulley Hardware D Mounting Bracket Hardware Install Turbo Blower 1 Install the turbo unit by sliding the turbo pivot rod into the pivot bracket at the front edge of the mower deck A Figure 17 2 Tilt the deflector B UP 3 Rotate the turbo unit C into position on the dis charge of the mower deck and latch the slot in the turbo housing over and onto the anchor bracket at D Tighten the wing nut E to secure Install Turbo Drive Belt 1 See Figure 18 Attach the turbo belt to the top RH pulley on the mower deck Pull back on the belt ten sioning lever to slacken the belt A view from right front of mower of the belt routing is shown at right NOTE While attaching it may be necessary to unlatch the turbo and realign the belt on the pulleys inside the turbo housing 2 After the belt is installed adjust the belt stop D Flgure 7 amp 8 so that it is 1 8 away from the backside of the belt Secure Belt Cover 1 The belt cover plate A Figure 19 is a safety shield after attaching or detaching the turbo unit it MUST BE rotated onto the belt cover latch B CAUTION Before you begin operating the unit with the Turbo attached be certain you have read all of the safety and operational information on the last page of this instruction sheet as well as the Operator s Manual for the tractor and any grass catche
19. ure with four 5 16 18 x 3 4 capscrews 1 washers E and 5 16 18 locknuts H Attach the back plate A to the support assembly B using 5 16 18 x 1 carriage bolts G 5 16 lockwash ers C and 5 16 nuts D Set the back plate and support A Figure 4 onto pins of hitch plate C Secure with rod D and hair pin B 11 Initial Hitch amp Tube Installation Figure 2 Install Hitch Plate Tube Style Bumper A Hitch Plate B Bumper Tube C U Bolts D Locknuts 3 8 16 Figure 3 Install Hitch Assembly A Back Plate G Carriage Bolts B Support Assembly 5 16 18 x 1 C Lockwashers 5 16 H Nylock Nut 5 16 18 D Nut 5 16 18 l Capscrews E Washers 5 16 5 16 18 x 3 4 F Cover Plate Initial Hitch amp Tube Installation Figure 7 Mount Deflector and Tube Pivot Figure 4 Install Back Plate Flat Style Bumper shown i Back Plate and Support Hitch Plate A Tube Pivot C 5 16 Mounting Hardware B Hair Pin D Rod B Deflector Deflector Locknut 5 16 18 Capscrew Back Plate Upper Tube 10 32 x 1 2 Capscrew Middle Tube Nut 10 32 5 16 18 x 1 Lower Tube Clip Socket Washer 10 Holes Washer 5 16 Figure 5 Assemble Tubes amp Deflector eight flat washers E and four nylock nuts F as Install Tubes amp Deflector 4 Insert the lower tube 1 Figure 5 into the middle tube H Secure the tubes as shown in Figure 5 using
20. x 3 4 12 1 COVER BELT 44 29 1 SPACER Pulley 46 1 SPRING Compression 13 1 3 8 16 30 1 CAPSCREW Head 5 16 18 47 1 SPACER Spring Holder 14 1 LOCKWASHER 3 8 31 1 WASHER 5 16 48 1 BRACKET Mounting 15 1 BRACKET Idler 32 1 LATCH Spring 49 1 V BELT 44 Turbo 16 1 LATCH Belt Cover 33 1 SPACER Figure 1 Contents of Turbo Installation Kit Initial Turbo Installation TURBO INSTALLATION Remove Mower Deck Remove the mower deck from the unit see Operator s Manual for instructions Deflector Removal 1 Remove and retain the carriage bolts washers lock washers and nuts A Figure 3 holding the deflector rod to the deck Remove and discard the deflector rod Retain the deflector Figure 3 Remove Deflector A Carriage Bolts Washers Lockwashers amp Nuts Install Discharge Baffle 1 Attach the baffle bracket A Figure 4 under the mower housing as shown and insert the carriage bolt from step 1 through the bracket amp deck hole at B 2 Attach the L bracket C to the baffle A and over the stone guard D Attach with carriage bolt spacer lockwasher and nut as shown Figure 4 Install Discharge Baffle A Baffle Bracket C L Bracket B Mounting Hole D Stone Guard Figure 2 Install Discharge Baffle A Cover and Bolts Install Deflector Hinge Assembly 1 Remove the bolts A Figure 2 securing the RH arbor cover then remove the cover from t
Download Pdf Manuals
Related Search