Skyworth SLTV-2063A Flat Panel Television User Manual
Contents
1. SLTV 1963A Skyworth SLTV 2063A WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The lighting flash with arrow head within a triangle is intended to tell the user that parts inside the product are a risk of electric shock to persons The exclamation point within a triangle is intended to tell the user that important operating and servicing instructions are in the papers with the appliance WARNING To reduce the risk of electric shock do not expose this apparatus to rain or moisture and objects filled with liquids such as vases should not be placed on this apparatus WARNING According to theindustrial standards thereare a certainnumber of defective pixels both bright and dark that are acceptable Although we produce panel with more than 99 99 percent active cells there still may be somecells that donot produce lightor remain lit For more information please contact salesor the technicalsupport WARNING Do not leave any stationary images patterns PIP box or letterbox images2. Tune You can modify settings on TVinput in thismenu All settings in this menu are effective for ATVonly Press CH CH buttons to select available items in this menuand perform correspondingoperation Note You can enterthis menu onlyin TV mode Color System Three color systems including NTSC PAL Mand PAL Nare supported by this TVset You can select AUTO to allow the TV set to detect and set color system automatically or force the TV set to display the chosen color system by pressing VOL VOL buttons when this itemis highlighted Once AUTO is selected system will detect the color system and force to display according to the detection result and this item will show which color system is forced by system while it takes a little time to finish the automatic detection Due to the complicated situation it isnot guaranteed that color system can be detected correctly by the TV set Please select proper colorsystem if necessary Function Menu Operation e TV Source Press VOL buttonto enter TVSource menu TV Source In TV Source menu you can switch TV source among Antenna Cable STD Cable IRC and Cable HRC by pressing VOL 4 button Please make it sure that proper TV Source is selected before auto scan is started otherwise programs may notbe found and stored Skip Press VOL VOL buttons to switch on or switch off the skipfunction If skipfunction is on you can not watch thecorresponding program b
3. Mute the sound DTV DIV Enter DTV Setting menu P M Select desired picture mode I II Select sound mode CC Enter CC setting menu TV AV TV AV Switch to desired input source Select channel or enter password Se G 9 4 9 2 o O 69 9 9 9 9 Select channel digits Q VIEW Back to previous viewed channel SLEEP Set the sleep timer Display information of current input Display menu function gt Q Channels Up Down 49 Volume Up Down 13 12 10 REMOTE CONTROL OPERATION TV MODE 1 POWER Button Press this button toturn the TV onor off 2 Mute Button cx Press once tomute the sound press again torecover previously set sound level This button willnot work if CC display isswitched on DTV Press this buttonto enter DTVsetting menu 3 Picture Mode Button P M Press this buttonto select desired picture mode Four picture modes areavailable including Custom Rich Standard and Softmode CUSTOM RICH 4 Y SOFT STANDARD 4 Sound Mode Button I II When stereo programis received p
4. OIC O amp 9 9 O O a O LO DOE e m EU lorxIgigloleolsi amp lol8lo 9 giejereisiojolsioislozl u c c 9 ISIOP HSImISISIgIgicigi5iE f H a e O S H El E B F 2 S a E hejm 9lolol amp ElziS9Sigsislit o c9ojojoil iciczeijol loj9 U o V G g F Q oj 0 Q 2 Els s S slalalalslalslsl s lI SS ss s EE symptoms amp f O O a a amp amp amp O lt O O O No picture no sound oo0 e Poor sound picture OK Poor picture sound OK eee ee 0000 c e Weak picture Blurred picture Double image OCCO Lines in picture AED CXC Distorted picture Weak reception on some channels Horizontal bars Picture rolls vertically Poor colour No colour Misoperation of Remote control C Hemote control unit no operation e On Screen Display Control outside the screen C 17 18 LIMITED WARRANTY SKYWORTH will repair this product free of charge in the USA in the event of defect in materials or workmanship as follows DURATION PARTS SKYWORTH will provide parts to replace defective parts without charge for one 1 year from the date of original retail purchase Certain parts are excluded from this warranty LABOR SKYWORTH will provide the labor without charge for a period of ninety 90 days from the date of original retail purchase LIMITS AND EXCLUSIONS This warranty is extended only to the original retail purchase A purchase receipt or ot
5. 0VERLOADING Do notoverload wall outlets and extension cords as this can result in a risk of fire or electric shock 16 0BJECT AND LIQUID ENTRY Do not push objects through any openings in this unit as they may touch dangerous voltage points orshort out parts that could result in fire or electric shock Never spill orspray any typeof liquid intothe unit 17 0UTDOOR ANTENNA GROUNDING If an outside antenna or cable system is connected to the unit be sure the antenna or cable system is grounded to provide some protection against voltage surges and built up static charges Section 810 of the National Electrical Code ANSI NFPA 70 provides information with respect to proper grounding of the mast and supporting structure grounding of the lead in wire to an antenna discharge unit size of grounding conductors location of antenna discharge unit connection to grounding electrodes and requirements for the grounding electrode 18 SERVICING Do not attempt to service this unit yourself as opening or removing covers may expose you to dangerous voltage or other hazards Refer all servicing to qualified service personnel 2e 19 DAMAGE REQUIRING SERVICE Unplug this unit from the wall outlet andrefer servicing to qualified service personnelunder the following conditions A Whenthe power supply cord or plugis damaged B If liquidhas been spilled or objects havefallen into the unit C If theunit has beenexposed to rainor water D
6. R L 00 00 6 O 8 9 do 0 0 Antenna or cable In Video S Video Audio Right In Video S Video Audio Left In Video In S Video In Component In Component PC Audio Right In Component PC Audio Left In PC In 10 Headphone Jack 11 Audio Right Out 12 Audio Left Out Rear Panel Connectors OoonNrOoOBR WD gt DC 12V D 1 DC 12V In Procedure e Connect equipment as shown to Audio Video input jacks Select the Video mode by pressing TV AV button Operate optional equipment as instructed in equipment manual Headphone jack Plug an earphone or monaural headphones into this jack for private listening Note BASIC CONTROLS AND CONNECTIONS Front Control Panel The front control panel can be used to access menus and switch video mode when the remote control is not available 2 N prera VOL Button VOL Button CH Button CH Button Menu Button TV AV Button Power Button Power Indicator Remote Sensor CON DOOR Co gt The ON OFF indicator LED red will light up when you insert the AC cord into the AC outlet je REMOTE CONTROL OPERATION Remote Control Operation POWER Turn on off MUTE
7. cabinet only 6 ATTACHMENTS The manufacturer of this unit does not make any recommendations for attachments as they may cause hazards 7 WATER AND MOISTURE Do not use this unit near water For example near a bathtub washbowl kitchen sink laundry tub in a wet basement or near a swimming pool 8 ACCESSORIES Do not place this unit on an unstable cart stand tripod bracket or table The unit may fall causing serious injury and serious damage to the unit An appliance and cart combination should be moved with care Quick stops excessive force and uneven surfaces may cause the appliance and cart combination to overturn PORTABLE CARTWARNING LA e 3126A 9 VENTILATION Slots and openings in the cabinet back or bottom are provided for ventilation to ensure reliable operation of the unit and to protect it from overheating These openings should never be blocked by placing the unit on a bed sofa rug or other similar surface This unit should never be placed near or over a radiator or heat source This unit should not be placed in a built in installation such as a bookcase or rack unless proper ventilation is provided or the manufacture s instructions have been adhered to 10 POWER SOURCE This unit should be operated only from the type of power source indicated on the rating plate If you are not sure of the type of power supply to your home consult your appliance dealer or local power company For u
8. on the screen foran extended period oftime Also do not displaythe same stationary patterns frequently This may resultin permanent ghost images on the display unit This type of damage is notcovered under warranty Examples of this type ofsituation can be but notlimited to thefollowing sidebar images stock market reportbars video game patterns closed captioning shopping channellogo price display and letterbox black bars To prevent thistype of damage display constant moving images thatfill the screen as often as possible CAUTION Changes or modifications not expressly approved by the party responsible for compliance with the FCC Rules could void the use s authority to operate this equipment TV CATV MODE SELECTION When shipped from the factory the TV CATV menu option is set to the TV mode If using CATV set the menu option to CATV Cable Television IMPORTANT SAFETY INSTRUCTIONS 1 READ INSTRUCTIONS All the safety and operating instructions should be read before the unit is operated 2 RETAIN INSTRUCTIONS The safety and operating instructions should be retained for future reference 3 HEED WARNINGS All warnings on the unit and in the operating instructions should be adhered to 4 FOLLOW INSTRUCTIONS All operating and use instructions should be followed 5 CLEANING Unplug this unit from the wall outlet before cleaning Do not use liquid cleaners or aerosol cleaners Use a damp cloth for cleaning the exterior
9. view 12 Function Menu Operation MPAA Rating Press VOL buttonto enter MPAA Rating menu V Chip gt MPAA Rating In this menu you can setMPAA rating Press CH CH buttons to select desired rating block or unblock theselected rating by pressing CH CH buttons Canada English Rating Press VOL buttonto enter CanadaEnglish rating menu when CAEng Rating itemis selected V Chip gt CA Eng Rating In this menuyou can setCanada English rating Press CH CH buttonsto select desiredrating block or unblockthe selected rating by pressing VOL VOL buttons Canada French Rating Press VOL buttonto enter CanadaFrench rating menu when CAFr Rating itemis selected V Chip gt CA Fr Rating In this menuyou can setCanada French rating Press CH CH buttonsto select desiredrating block or unblockthe selected rating by pressing VOL VOL buttons V Chip Block If the programis set tobe blocked blackscreen will be displayed and volume is muted Following dialog indicates V Chip works and allows adults to enter password Function Menu Operation Input your password press VOL to confirm If the password is correct image and volume will recover Otherwiseimage and volume will still be blocked andabove dialog willnot disappear Setup menu You can changesome basic settings of the TV set in this menu Press CH toenter this menu Press CH CH buttons to select available items in this menuand perf
10. wish to use a two set signal splitter sometimes called a two set coupler and an A B switch box from the cable installer or an electronics supply store Follow the connections shown left With the switch in the B position you can directly tune any nonscrambled channels on your TV With the switch in the A position tune your TV to the output of the converter descrambler box usually channel 3 or 4 and usethe box to tunescrambled channels This television has an extended tuning range and can tune most cable channels without using a cable company y Converter Descrambler C m supplied converter box Some cable companies offer premium pay channels in which the signal is scrambled Converter Deserarnbiet Descrambling these signals for normal viewing requires the use of a descrambler device which is generally provided by KC Spltter A B Switch 8 C DI the cable company Ge Optional Equipment Connections Side Panel Connectors Pr R AUDIO IN 1 COMPONENT Pb ANTIN j VIDEO SMDEO APON Be TE PORT
11. If the unitdoes notoperate normally by following the operatinginstructions Adjust only those controlsthat are coveredby the operating instructions asan improper adjustment of other controls may resultin damage and will often require extensive work by a qualifiedtechnician to restorethe unit to Its normal operation E If theunit has beendropped or thecabinet has been damaged F Whenthe unitexhibits a distinct change in performance this indicatesa need forservice 20 REPLACEMENT PARTS When replacement parts are required be sure the service technician uses replacement parts specified by the manufacturer or those that have the same characteristics as the original part Unauthorized substitutions may result in fire electric shock or other hazards 21 SAFETY CHECK Upon completion of any service or repairs to this unit ask the service technician to perform safety checks to determine that the unitis in properoperating condition 22 HEAT The product should be situated away from heat sources such as radiators heat registers stoves or other products including amplifiers that produceheat 23 NOTE TO CATV SYSTEM INSTALLER This reminder is provided to call the CATV system installer s attention to Article 820 40 of the NEC that provides guidelines for proper grounding and In particular specifies that the cable ground shall be connected to the grounding system of the building as close to the point of cable entry as practical E
12. RIGINAL PURCHASER AND DOES NOT EXTEND TO SUBSEQUENT OWNERS OF THE PRODUCT ANY APPLICABLE IMPLIED WARRANTIES INCLUDING THE WARRANTY OF MERCHANTABILITY ARE LIMITED IN DURATION TO A PERIOD OF THE EXPRESS WARRANTY AS PROVIDED HEREIN BEGINNING WITH THE DATE OF ORIGINAL PURCHASE AT RETAIL AND NO WARRANTIES WHETHER EXPRESS OR IMPLIED SHALL APPLY TO THIS PRODUCT THEREAFTER SKYWORTH MAKES NO WARRANTY AS TO THE FITNESS OF THE PRODUCT FOR ANY PARTICULAR PURPOSE AND USE UNDER NO CIRCUMSTANCES SHALL SKYWORTH BE LIABLE FOR ANY LOSS DIRECT INDIRECT INCIDENTAL SPECIAL OR CONSEQUENTIAL DAMAGE ARISING OUT OF OR IN CONNECTION WITH THE USE OF THIS PRODUCT THIS WARRANTY IS VALID ONLY IN THE UNITED STATES OF AMERICA THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS HOWEVER YOU MAY HAVE OTHER RIGHTS WHICH MAY VARY FROM STATE TO STATE SOME STATES DO NOT ALLOW LIMITATION ON IMPLIED WARRANTIES OR EXCLUSION OF CONSEQUENTIAL DAMAGE THEREFORE THESE RESTRICTIONS MAY NOT APPLY TO YOU ATTENTION SKYWORTH reserves the right to modify any design of this product without prior notice Skyworth Electronics Inc 1312 John Reed Court City of Industry CA91745 Phone 626 336 3698 Fax 626 336 3238 Email service skyworth com hk Http www skyworth com hk 19
13. V NATIVE RESOLUTION 1366 x 768 BRIGHTNESS 450 cd m CONTRAST RATIO 600 1 n MTS stereo optional SAP On Off PARENTAL CONTROL V Chip SLEEP TIMER Off only OTHER FEATURES MULTI LANGUAGE OSD yes WALL MOUNTING VESA Compliant 100 x 100 mm Bracket not included VIDEO 4 Preset Video Modes Custom Rich Soft Standard STAND Swivel Stand AUDIO OUTPUT 2W x 2 MAX INPUTS Component x 1 Y Cb Cr Y Pb Pr VIDEO Progressive Interlaced Scan S Video x 1 4 pin DIN Composite Video x 1 RCA D Sub 15 x 4 RGB AUDIO L R RCAx2 OUTPUT HEADPHONE AUDIO L RX1 POWER POWER REQUIREMENT DC 12V 5 Amps Use the AC DC adaptor supplied 45W pee DS User s Manual AC DC Adapter Remote Control 2 AAA Batteries DC Car Cord optional DIMENSIONS WHD 21 7 16 x 7 1 16 x 16 1 4 inches with stand 24 44 x 9 7 16 x 18 1 2 in UNIT ONLY Note Specification are subject to change without prior notice Installation Television Location Follow these recommendations before deciding the location of your television e Avoid excessive sunlight or bright lights including reflections Keep away from excessive heat or moisture Inadequate ventilation may cause internal component failure Fluorescent lighting may reduce remote control transmitting range Keep away from magnetic equipment including motors fans and external speakers WARNING Use this televisio
14. XAMPLE OF ANTENNA GROUNDING AS PER NATIONAL ELECTRICAL CODE 2898A ANTENNA LEAD IN WIRE ANTENNA DISCHARGE UNIT NEC SECTION 810 20 N Z XK ELECTRIC L WS A e NEC NATIONAL ELECTRIC CODE GROUNDING CONDUCTORS NEC SECTION 810 21 GROUND CLAMPS POWER SERVICE GROUNDING ELECTRODE SYSTEM NEC ART 250 PART H Table of Contents Congratulations 4 Specifications 4 SISTA OD Hessen 5 Television Location aa 5 Remote Control Battery Installation 5 Power Source 5 Combination VHF UHF Antenna aaa 6 Optional Equipment Connections 7 Rear Panel Connectors 7 Pront Contool Pane eee 7 Remote Control Operation 8 11 TA FV a ee 8 11 TABLE OF CONTENTS Function Menu Operation 12 16 PICTURE 7 7 7 12 V CHIP 42 Setup MENU esee 13 Special Message 16 SONCE TPS AAAA 17 Limited Warranty 18 19 3e CONGRATULATIONS Congratulations Your new TV Monitor Receiver features a solid state chassis that is designed to give you many years of enjoyment It was thoroughly tested and tuned at the factory for best performance SPECIFICATIONS PANEL 19 BRIGHTNESS 300 cd m CONTRAST RATIO 700 1 20 ACTUAL VIEWING AREA 433 61 x 249 41 mm H x
15. eceived signal strength levelis 60 or higher e Audio Setting Press VOL buttonto enter DIVAndio Setting menu Audio Setting menu AUDIO SERVICE English Stereo Main complete Digital audio parameterscan be setin this menu e Audio Service Press VOL buttonto enter Audio Service menu in which you canselect preferred audioservice Totall six digital audioservices are possibly available to be selected Whileactually selectable audioservice depend on whatkind of audioservice is contained in current program e Audio preference Press VOL buttonto enter Audio Preference menu in which youcan select preferred audio language Three kinds of audio language areselectable including English Spanishand French While one kind of language can notbe chosen as primary language and secondary language at thesame time e CC Setting Press VOL buttonto enter DIVCC Setting menu e Factory Reset Press VOL buttonto reset DTVsettings with default value Note It is strongly recommended that you should scan DTV programs right after reset DTV settings Otherwise you can not watch all DTV programs e Aspect Only DTV display aspect ratio canbe selected between model and mode2 using thisitem Please choose preferred one e Auto Scan Press VOL buttonto start DTV auto scan Ittakes a few minutes During the autoscan process please do notterminate it by turning off the TV set Otherwise the programinformation may notbe stored Tune menu
16. gh following functions e HPos and VPos Adjust the position of the PCimage through these items by pressing VOL VOL buttons Adjust the position of PC image horizontally through HPos item and adjustthe position of PC image vertically through VPos item e Phase Adjust the phase of the PCimage by pressing VOL VOL buttons Itwill make theimage sharp or blurry e Clock Adjust the clockof the PCimage by pressing VOL VOL buttons It will change the width of the active imageof the PCinput e Note Supported PC inputformat includes Vertical MODE Resolution Frequency VGA 640X480 60Hz SVGA 800X600 60Hz XGA 1024X768 ai Other formats maybe supported bythe TV set 15 Function Menu Operation Function Menu Operation Special Message e No Signal This message indicates there is no signal for PC input If there isno signal for PC input blackscreen will be displayed and above dialog mentions you to plug PC signal For all inputs other than PC input blue screen will be displayedif there isno valid input e Out Of Range Because ofthe limitation of the LCD panel some picture format cannot be displayed normally This message indicates that current inputexceeds the display ability of the panel e Invalid Mode Due to thelimitation of microchipsused by the TV set somepicture format cannot be supported by the TV set This message indicates thatthe TV set can notperform normal image managemen
17. he Car Cord provided for operation on 12V DC NOTE 1 AC DC adaptor provided can be connected to the specified voltage AC 110 volts 60HZ 2 lf the polarized AC cord does not fit into a non polarized AC outlet do not attempt to file or cut the blade It is the user s responsibility to have an electrician replace the obsolete outlet 3 f you cause a static discharge when touching the unit and the unit fails to function simply unplug the unit from the AC outlet wait a few minutes and plug it back in The unit should return to normal operation He INSTALLATION Combination VHF UHF Antenna Combination VHF UHF Antenna Single 75 ohm cable or 300 ohm twin lead wire Connect the 75 ohm cable from a combination VHF UHF antenna to the antenna jack Combination VHF UHF Antenna Separate VHF and UHF 300 ohm twin lead Connect the UHF twin lead wire to a combiner not supplied Connect the VHF twin lead to the 300 75 ohm matching transformer notsupplied Attach the transformer to the combiner Attach the combiner to the antenna jack Separate VHF UHF Antenna Connect the 75 ohm cable from the VHF antenna and the UHF antenna twin lead to a combiner not supplied Attach the combinerto the antenna jack NOTE If your VHF antenna has a twin lead wire use the 300 75 ohm matchingtransformer not supplied then connect the transformerto the combiner For Subscribers to Basic Cable TV Service For basic cable service not requir
18. her proof of original retail purchase will be required together with the product to obtain service under this warranty This product is eligible for CARRY IN service only SKYWORTH will not be liable for damages incurred in shipment of the unit If there are no SKYWORTH authorized Independent Service Centers in your area please call 1 877 336 3698 or 626 336 3698 for assistance Note This warranty is void if the product is a Damaged through negligence misuse abuse or accident b Used in a commercial application or rentals c Modified or repaired by anyone other than an Independent Service Center authorized by SKYWORTH to effect warranty repairs to the class of product or by the SKYWORTH Factory Service Center d Damaged because it is improperly connected to the equipment of other manufacturers This warranty does not cover a Damage to equipment not properly connected to the product b Cost incurred in the shipping of the product to a SKYWORTH authorized Independent Service Center or SKYWORTH Factory Service Center c Damage or improper operating of unit caused by customer abuse misuse negligence or failure to follow operating instructions provided with the product d Ordinary adjustments to the product which can be performed by customer as outlined in the owner s manual e Signal reception problems caused by external antenna or cable systems THIS WARRANTY IS NON TRANSFERABLE AND APPLIES ONLY TO THE O
19. ing a converter descrambler box connect the CATV 75 ohm coaxial cable directly to the antenna jack on the back of the television Combination VHF UHF Antenna hm Single 75 ohm cable 300 ohm twin lead wire e _ gt amp Splitter ETET 300 75 OHM MATCHING aa ue Antenna Take off the Splitter TRANSFORMER not supplied 300 ohm twin lead wire E 5 VHF Antenna Single 75 ohm cable p gt p 300 ohm twin lead wire lt COMBINER 300 75 OHM MATCHING TRANSFORMER Incoming CATV not supplied F C Du not supplied For Subscribers to Scrambled Cable TV service If you subscribe toa cable service which requires the use of a converter descrambler box connect the incoming cable to the converter descrambler box and connect the output of the box to the antenna jack on the back of the television Follow the connections shown left Set the television to the output of the converter descrambler box usually channel 3 or 4 and use the converter descrambler box to select channels For Subscribers to Unscrambled Basic Cable with Scrambled Premium Channels If you subscribe to a cable service in which basic cable channels are unscrambled and premium channels require the use of a converter descrambler box you may
20. itched to automatically after two seconds 7 Number 0 9 Button Press these buttonsto enter digits These buttons fordirect access touse a channelto enter channel number forboth ATV and DTV or enter password for V Chip 8 Digit Button For ATV press this button to select one digit two digit and three digit channelaccess For example selecting channel 8 youcan press 8in mode press 08 in mode press 008 in mode It can switch channel digit accordingto user inputs automatically For example currentsetting is three digit option If two numbers are entered and switch to this channel two digit option is setautomatically If an invalid channel number isentered it willkeep displaying current channel For DTV Pressingthis button completes physical number inputfor channel number anda dot will be displayed 9 Quick View Button Q VIEW Press this buttonto watch the previously viewed channel for both ATVand DTV 10 Sleep Timer Button G _ ma nae a e n a a mee Press this buttonto set sleeptime You can adjustsleep time in minutes by pressingthe VOL buttons in the order shown below 0 10 20 30 120 13 12 10 REMOTE CONTROL OPERATION 11 Recall Button Press this buttonto display information on current input 12 Menu Button Press this button to enter Picture menu orquit from current menu 13 Channel Up CH Down CH Button Press these bu
21. n receiver only with the cart stand tripod bracket or table specified by the manufacturer or sold with the apparatus When a cart is used use caution when moving the Cart apparatus combination to avoid injury from tip over In order to avoid injury to children never place your television receiver on a piece of furniture that is capable of being tilted by a child leaning on it pulling on it standing o it or climbing on it A falling television can cause serious injury or even death Remote Control Battery Installation Requires two AAA batteries supplied INSTALLATION Procedure 1 Turn the remote control face down Remove battery cover by pressing down on the marking on the cover and sliding it off in the direction indicated 2 Install batteries matching and polarity signs 3 Replace the battery cover by sliding in reverse until the lock snaps Note Incorrect installation can cause battery leakage and corrosion that will damage the Remote control Precautions e Replace batteries in pair e Do not mix battery types zinc carbon with alkaline e Do not recharge heat short circuit disassemble or burn batteries POWER SOURCE TO USE AC POWER SOURCE Use the AC DV adaptor provided for operation on AC Insert the AC cord plug into a standard 110 120V 60HZ polarized AC outlet AC outlet Wider Hole and Blade Polarized AC Cord Plug One blade is widerthan the other To use Car cord Use t
22. nits intended to operate from battery power or other sources refer to the operating instructions 11 POLARIZATION This unitis equipped with a polarized alternating current line plug a plug having one blade wider than the other This plug will fit into the power outlet only one way This is a safety feature If you are unable to insert the plug fully into the outlet try reversing the plug If the plug stillfails to fit contact your electrician to replace your obsolete outlet Do not defeat the safety purpose ofthe polarized plug 12 POWER CORD PROTECTION Power supply cords should berouted so that they are not likely to be walked on or pinched by items placed upon or against them paying particular attention to cords at plugs convenience receptacles and the point where theyexit from theappliance 13 LIGHTNING To protect your unit during a lightning storm or when it is left unattended and unused for long periods of time unplug it from the wall outlet and disconnect the antenna or cable system This will prevent damage to theunit due to lightningand power linesurges 14 POWER LINES An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits or whereit can fallinto such power lines or circuits When installing an outside antenna system extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal 15
23. orm correspondingoperation OSD Language Multi Language OSD aresupported by this TV set You canselect desired OSD language by pressing VOL VOL buttons Factory Reset Select this item press VOL to startFactory Reset function Ittakes a fewseconds to recover back almost all settings with default value except for the DTV settings You cantry thisfunction wheneverthere is something wrong with the TV set and you can not fix it DTV Setting Select this item and press VOL toenter DTV setting menu OSD HPos and OSD VPos You can adjustthe position ofthe main menu includes Picture menu V Chip menu etc Adjust the position of main menu horizontally through OSD HPos item and adjust the position of main menu vertically through OSD VPos item Aspect This function works for all available sources Select display aspectratio between 16 10 and 4 3mode by pressing VOL VOL buttons 13 Function Menu Operation Function Menu Operation Audio Setting CC Setting Factory Reset Aspect Auto Scan DTV related functionscan be reachedin this menu e Antenna level Press VOL buttonto enter DTV Antenna level menu Antenna level menu ANTENNA SETUP DIGITAL SIGNAL STRENGTH CHANNEL STRENGTH Adjust the antenna until the level is 60 or hige Signal strength Current VERS This menu assists you to adjustthe position and direction of the antenna so that best signal can be received Adjust the antenna until ther
24. p function video and audio will notbe blocked Picture menu e Change Password Press VOL buttonto enter Password Change Brightness menu tore set V Chip password Contrast Hue Color Sharpness New Password A Confirm Password After enter new password which consists of only digitals and spaces press VOL to confirm Enter the new password again then press VOL button to confirm again If the same password is entered twice Successful will be In Picture menu you can press CH CH buttons to select available itemsand adjust brightness contrast hue colorand sharpness by pressing VOL VOL buttons displayed to indicatethat you havechanged the password successfully lf the passwordsare Note different Unmatched isdisplayed to indicate e Hue isonly availablefor NTSC system that new passwordis invalid andallow you to e Both Hueand Sharpness settings are not re enter the new password Press MENU button available for PCinput to return to V Chip menu V Chip menu S TY nating Press VOL buttonto enter TV Rating menu Lock Change Password TV Rating MPAA Rating CA Eng Rating CA Fr Rating You can set parameters on V Chip In this menu you can set TV rating Press parental control inthis menu Allsettings are CH CH and VOL VOL buttons to select effective for both ATV and DTV desired rating blockor unblock theselected The default V Chip Password is setas 1111 rating Bmeans block and V means
25. ressthis button to switch sound system between mono andstereo When sap program is received press this button to switch sound system between mono and sap When stereo and sap programis received pressthis button to switch among mono sap and stereo 5 Closed Captioning Button CC CC Status CC Mode Press this button to enter CC setting menu for analog input whichis shown above if any source except for DTV is watched In this menu you can switch on and off the CC displayand select desired CC mode including CC1 CC2 CC3 CC4 Text1 Text2 Text3 and Text4 mode CC modecan be set only when CC display is switched on DTV CC Setup menu CLOSED CAPTION CLOSED CAPTION SERVICE CLOSED CAPTION PREFERENCE Press this buttonto enter CC setting menu for DTV ATSC if DTVis watched In this menu DTV CC service and preferencecan be set Note Only the DTV CC serviceavailabce from theDTV broadcasting can be selected Ilf there is no signal for DTV CC serviceitem is notselectable Oe REMOTE CONTROL OPERATION 10 13 12 10 To quitthis menu please press CC button again or MENU button orit will disappearautomatically after 10 second display 6 TV AV Button TV AV n Press this button to select the desired inputsource among TV DTV Video S Video Componentand PC You can press this button to switch among all available inputs inthis menu continuously until desired input is displayed Selected input willbe sw
26. t for current inputformat Note For TV input only NTSC systemis supported For Component input following formats are supported 480i 060Hz 480p 60Hz 5761 050Hz 576p 50Hz 720p 50Hz 720p 60Hz 1080i 50Hz 1080i 60Hz 16 Auto Configuration This message indicates that PC automatic configuration isin process After finish PC image adjustment this message will disappear Image Shrink This message indicatessystem is shrinkingthe input signal soas it canbe displayed although part of theimage will belost For someinput formats which cannot be displayednormally due to the limitationof the panelor microchips used by the TV set software system will automatically calculate and delete part of the image and allow primary part ofthe imageto bedisplayed Note Sometimes for somesupported input format system will alsoautomatically calculate and decide whether or notshould shrink theinput image During this process Image Shrinking message is also displayed Whileif system findsthat input format should be supported by the TV set this message will disappearand the wholepicture will be displayed Service Tips indicated e on the chart for the remedies Service Tips Please make these simple checks as respective symptoms and their possible O o J O O C 5 Es z fs S Sig ae G 3 E o a Ofa oO Q ee Pm id O Ig O C 4 4 Sl amp le via E A 5 fo 2 gl a SV EI Xilol lo O Guo I p O J
27. ttons to select channelsin ascending or descending order for both ATV and DTV or select available items ina menu 14 Volume Up VOL Down VOL Button Press these buttonsto increase ordecrease volume and also toadjust the settingssuch as brightness in thePicture menu LockOn Off in the V chip menu etc Volume Increase VOL button is also used toconfirm your selectionor enter nextmenu 15 DTV Setting MenuButton DTV Press this buttonto enter DTV Setting menu 11 Function Menu Operation Function Menu Operation Press CH button to enter V Chip menu ifthere is no password orenter Password Checkmenu Brightness Contrast Check Password eus Enter Password Color Sharpness After input password which consists of only digitals and spaces press VOL buttonto confirm If the password is correct return to SS V Chip menu Otherwise Check Password menu Press MENU buttonto display Picturemenu You can keep displayed andallow you tore enter the browse Picture V Chip Setup Tune andPC Setup password Press MENU button to quit from this menu by pressing VOL VOL buttons Press CH menu forcedly button to enterthe selected menuand adjust available settings by pressing VOL VOL buttons e Lock or confirm youselection or enternext menu by Press VOL VOL buttons to select On which pressing VOL button switches on V Chip function or Off which switches off V Chipfunction If switch off V Chi
28. ypressing CH CH buttons While you can watch this program by entering the channel number directly Fine Tune Try this function if TVimage is not good The adjustable frequency range is 625KHz Note AFT Automatic frequency tune functionis also available TV set will adjust the frequency of TV signal automatically to obtain the best effect unless you adjustfrequency through FineTune function manually Auto Scan Press VOL buttonto search and store all available programs automatically Note TV set willstore programs ofcable and antenna systems separately Connectcable to yourTV set switch to cablesystem through TV Source item Available programs willbe stored through channel No 1 to channel No 125 Then Connect antenna to your TV set switch to antennasystem through TV Source item Available programs will be stored through channel No 2to channel No 69 Function Menu Operation PC Setup menu PC Setup You can modify settings on PCinput in this menu Press CH CH buttons to select available items in this menuand perform correspondingoperation Note You can enterthis menu onlyin PC inputand there is validsignal for the PC input e Auto Adjust Press VOL buttonto start adjustPC settings automatically It will take a few seconds to finish the adjustment includinghorizontal and vertical position phase and clock ofthe PC image If you are not satisfied with the effect you can adjust these settings manuallythrou
Download Pdf Manuals
Related Search