Simplicity 1694924 Lawn Mower User Manual
Contents
1. Amputation and thrown objects hazard To avoid injury from rotating blades and thrown debris stay clear of deck edge and discharge Do not mow without deflector or entire grass catcher in place 1700259 Decal Danger Thrown Objects Rotating Blades Part No 1700259 Amputation hazard To avoid injury from rotating pulleys and belts stay clear of pulleys belts and the edge of this cover Do not mow without deflector or entire grass catcher in place Decal Warning Shield Placement Deflector Position Part No 1717291 Safety Icons The alert symbol A is used to identity safety information about hazards that can result in personal injury A signal word DANGER WARNING or CAUTION is used with the alert symbol to indicate the likelihood and the potential severity of the injury In addition a hazard icon may be used to represent the type of hazard An explanation of hazard levels and icons are as follows DANGER This indicates a hazard which if not avoided will result in serial injury or death A WARNING This indicates a hazard which if not avoided could result in serial injury or death A CAUTION This indicates a hazard which if not avoided might result in minor or moderate injury CAUTION or NOTICE These messages presented without the alert symbol indicate a situation where the unit or property could be damaged Amputation Rotating Safety Identificat2. Figure 13 Install Up Stop A Up Stop B Capscrew Taptite 5 16 18 x 5 8 Install Up Stop 38 Mowers 1 Install the up stop A Figure 13 securing with 5 16 18 x 5 8 capscrew B as shown Install Deflector Latch 38 Note The 44 amp 50 deflector latch is typically per assembled and attached to the deflector bracket Check that the deflector latch stack up is correct See Figure 14 If necessary revise stack up as follows 44 and 50 Mowers Insert 5 16 18 x 2 1 2 capscrew H into bracket F Install 5 16 washer C spring latch E 5 16 18 nut D 5 16 washer 5 16 18 wingnut B and 5 16 nylock nut A onto capscrew H as shown 38 Mowers Slide 5 16 washer C spring latch E onto 5 16 18 x 2 1 2 capscrew H Install bracket G 5 16 18 nut D 5 16 washer 5 16 18 wingnut B and 5 16 nylock nut A onto capscrew H as shown to make deflector latch assembly 1 Install the deflector latch assembly A Figure 15 to existing holes C securing with 5 16 18 x 5 8 capscrews B Bracket F mounts to Baffle Bracket on 44 amp 50 Mowers Bracket G mounts to Mower Deck on 38 Mowers Figure 14 Deflector Latch Stack Up A Nut Nylock 5 16 18 Wingnut Special 5 16 18 Washers Flat 5 16 Nut KEPS Lock 5 16 18 Spring Latch Bracket Latch 44 and 50 Mowers Bracket Latch 38 Mowers Capscrew 5 16 18 x 2 1 2 TONMOOW Figure 15 Install De
3. Install Turbo Belt and Roller 1 2 Place the mower deck in the highest cut position Slide the pivot pin A Figure 19 into pivot bracket F Raise the deflector B Rotate the turbo C and latch the slot in the turbo housing over and onto the anchor bracket D Slot in mounting latch A gure 17 amp 18 to be around outside nut If not reposition mounting latch on turbo Tighten the wingnut E and cupwasher to secure turbo C Attach the mower drive pulley to the mower deck drive pulley B Figure 20 Pull back away from deck on belt tension lever C Install the turbo drive belt on pulleys as shown and release the belt tension lever C Models With Rollers Remove and discard the pushnut B Figure 21 and roller A from the right side of mower deck as shown Models With Rollers Install the roller A Figure 22 and 5 8 pushnut B from the right side of mower deck as shown Figure 20 Turbo Belt Routing nmo A Turbo Drive Belt Mower Deck Drive Pulley Belt Tension Lever Idler Pulleys Mower Deck Turbo Drive Pulley Turbo Drive Pulley Figure 21 Remove Right Side Pushnut and Roller A Roller Hollow B Pushnut 5 8 Figure 22 Install Right Side Pushnut and Roller A Roller Solid B Pushnut 5 8 www SimplicityMfg com www MasseyLawn com www AGCOLawn com www Snapper com 50 On
4. Do not tighten hardware at this time 4 Tighten all hardware A 2 2 7 e Figure 3 Install Discharge Baffles 38 Mower iE Qmm tu otu A Discharge Baffle Carriage Bolt 1 4 20 x 3 4 Locknut KEPS 1 4 20 Carriage Bolt 5 16 18 x 1 1 4 Spacer Bracket Locknut KEPS 5 16 18 Stone Guard Figure 4 Install Discharge Baffles 44 and 50 Mower Discharge Baffle Assembly Cover Mower Locknut KEPS 1 4 20 Carriage Bolt 1 4 20 x 3 4 Locknut Whiz 5 16 18 Capscrew 5 16 18 x 7 8 Stone Guard www SimplicityMfg com www MasseyLawn com www AGCOLawn com www Snapper com Install the Deflector Hinge Bracket and Deflector 1 Slide the deflector support rod A Figure 5 into pivot bracket B as shown Secure the front of the pivot bracket B using 5 16 18 x 3 4 carriage bolt and 5 16 18 nut F 38 Mowers Secure the back of pivot bracket B and support G using 5 16 18 x 3 4 carriage bolt and 5 16 18 nut F 44 and 50 Mowers Secure the back of pivot bracket B and support G using 5 16 18 x 7 8 capscrew 5 16 washer E and 5 16 18 nut F Drill four 13 64 holes from the bottom of the deflector A Figure 6 at the pre molded drill hole locations E Attach the deflector A to the rod D using the 1110 24 screws B and 10 24 nuts C Figure 5 Install Deflector Hinge and Bracket
5. Simplicity us AGCO SNAPPER OPERATOR S MANUAL Turbo Vacuum System For 38 44 amp 50 Mower Decks Mfg No Description 1694924 Turbo Vacuum Collection System Manual No 1732839 Revision 02 Revision Date 10 2006 TP 100 4286 02 AT SMAN Table of Contents Safety Rules amp Information 2 Safety RUES sinoni ennenen eei aiii Aa eedd aaa naana 2 Safety Decals sesssssssssssssseeeeennenen nennen 3 Safety Icons 3 Identification Numbers 4 trip Pee t 5 Initial ASSembly i nitrate uet er tbe cte ein ees 5 Normal Removal and Installation 20 Normal Removal and Installation 20 NOTE In this manual left and right are referred to as seen from the operating position Ayayes Ajquiessy o 3 2 J o 3 e 2 go 5 o eh D p O 3 Safety Read these safety rules and follow them closely Failure to obey these rules could result in loss of control of unit severe personal injury or death to you or bystanders or damage to property or equipment This mowing deck is capable of amputating hands and feet and throwing objects The triangle A in text signifies important cautions or warnings which must be followed PREPARATION 1 Do not operate the equipment without wearing adequate outer garments and safety goggles Avoid loose fitting clothes and use protective footwear t
6. Deflector Support Rod Pivot Bracket Carriage Bolts 5 16 18 x 3 4 Capscrew 5 16 18 x 7 8 Washer Flat 5 16 Nut Whizlock 5 16 18 Support Belt Cover onmo Figure 6 Install Deflector Deflector Screws Phillips 10 24 x 3 4 Nuts Nylock 10 24 Rod Deflector 13 64 Hole Locations D gt moo Ajquiessy Assembly Figure 7 Discard Taptite Screws A Taptite Screws Install Idler Assembly and Belt Guide 1 Remove and discard the two taptite screws A Figure 7 from the locations shown 2 Check that the idler assembly stack up is correct for your application See Figure 8 If not follow the descriptions to make the corrections 3 Install 5 16 18 x 7 8 capscrews C Figure 9 through the mower deck and arbor as shown Tighten capscrews 4 Install the idler assembly A to the mower deck using 5 16 18 x 7 8 capscrews C and 5 16 18 nuts The belt guide should be positioned as shown 5 44 and 50 Mowers Remove and discard the taptite screw in existing hole F Figure 10 if unit has roller bars 6 44 and 50 Mowers Install wire belt guide A Figure 10 spacer E washers D washer C and capscrew B as shown 44 and 50 Mowers 38 Mowers Figure 8 Idler Assembly Stack Up A Capscrew 3 8 16 x 2 Washer s 3 8 Pulley Idler 2 3 4 Idler Bracket Nut Whiz Lock 3 8 16 Belt Guide Wire 38 Mowers
7. Figure 34 Install Set Collar A Lift Rod B Set Collar C Set Screw D Hod Tip 6 Slide set collar B Figure 34 onto lift rod A Secure set collar B so that the top of the collar is 4 from the bottom of the rod tip D and that the rod tip and set screw point in opposite directions 7 Install the spring G Figure 35 and special nut D in the same location that was marked in step 5 8 Install the spacer E and locknut B 9 Connect special nut D to lift bar C 10 Reinstall the rod A to lift H and secure with hair pin F 11 Re level mower deck following procedures in the Operator s Manual see MOWER DECK LEVELING Ajquiessy D Figure 35 Install Lift Rod A Lift Rod B Locknut C Lift Bar D Special Nut E Spacer F Hair Pin G Spring H Lift 19 c ud T m o o T o o E O cc E o Z Normal Removal amp Installation Turbo amp Tube Installation Note The grass catcher hitch channel and cover must be installed according to the Catcher Operators Manual before proceeding with the next steps 1 2 Place the mower deck in the highest cut position Slide the pivot pin A Figure 36 into pivot bracket F Raise the deflector B 4 Rotate the turbo C and latch the slot in the turbo housing over and onto the anchor bracket D Tighten the wingnut E to secure turbo C Pull back away from deck
8. Belt Guide Flat 44 and 50 Mowers Spacer Io nm Figure 9 Install Idler Assembly A Idler Assembly B Belt Guide C Capscrew 5 16 18 x 7 8 D Nut Whizlock 5 16 18 10 www SimplicityMfg com www MasseyLawn com www AGCOLawn com www Snapper com Figure 10 Install Wire Belt Guide 44 amp 50 Mower Deck Wire Belt Guide Capscrew 5 16 18 x 1 1 2 Lockwasher 5 16 Washers Flat 5 16 Spacer Existing Hole nmo Install the Turbo Drive Pulley 1 Remove the arbor drive belt from the right side arbor pulley 2 Remove and discard locknut A Figure 11 and spring washers B Retain pulley C and spacer D 3 Install new spacer E Figure 12 turbo drive pulley C 5 for 38 mowers or D 4 5 16 for 44 amp 50 mowers and spring washer B align the notches in the pulleys with the ridges in the spacers Torque the sleeve nut to 55 70 ft Ibs 4 Install the arbor drive belt from the right side arbor pulley Figure 11 Remove Hardware A B Locknut Spring Washers C Pulley D Spacer Torque to 55 70 ft Ibs A 75 95 Nm A Sleeve Nut New Qmm OOD Spring Washer New Turbo Drive Pulley 5 for 38 Mowers New Turbo Drive Pulley 4 5 16 for 44 amp 50 Mowers New Spacer New Pulley Existing Spacer Existing 11 Ajquiessy Assembly
9. 19719 1732801 1705142 1732735A N A 1733077 1732799 1705308A 1960074 1732800 1919438 1930601 720727 1733076 1666294 Description Ref Part No Qty PIVOT amp BRACKET ASSEMBLY 54 1960223 1 NUT Hex Flange Lock 5 16 18 55 1713091 1 SUPPORT Belt Cover 56 1722750A 1 BELT Cover 50 Mower Decks 57 1724372 1 WASHER 5 16 CAPSCREW 5 16 18 x 7 8 58 1667811 1 Carriage Bolt 5 16 18 x 3 4 59 1733580A 1 Carriage Bolt 1 4 20 x 3 4 60 1960404 2 DECAL Warning 61 1933896 2 COVER 62 1733579 1 NUT Hex KEPS Lock 1 4 20 63 1717496 1 BAFFLE 64 1719777 1 CAPSCREW 5 16 18 x 2 1 2 65 1928721 SUPPORT 66 1729277 1 SPRING LATCH 67 1709256 1 WASHER NUT Hex KEPS Lock 5 16 18 BELT Cover 44 Mower Decks ROD NUT Hex 210 24 SCREW Phillips 10 24 x 3 4 CAPSCREW 3 8 16 x 2 WASHER 3 8 PULLEY Idler 2 3 4 O D WASHER L BRACKET Z BRACKET NUT Hex Flange Lock 3 8 16 CAPSCREW 5 16 18 x 1 1 2 LOCKWASHER 5 16 BELT STOP SPACER NUT Sleeve 9 16 18 WASHER Bellville PULLEY 4 5 16 O D HUB PUSH NUT 5 8 ROLLER TUBE amp CLIP ASSEMBLY V BELT 39 5 8 50 Mower Decks V BELT 39 11 16 44 Mower Decks FLANGE Seal DECAL Patent LATCH SEAL L BRACKET CLIP Hair Pin ELBOW NUT Hex Nylock 5 16 18 SCREW Hex Taptite 5 16 18 x 5 8 WINGNUT 5 16 DEFLECTOR SPACER Description CARRIAGE BOLT 5 16 18 x 1 1 4 PULLEY 5 0 O D UP STOP BRACKET V BELT 47 11 16 38 Mower Decks SP
10. ACER DEFLECTOR PLATE SCREW 10 24 x 3 4 NUT Nylock 10 24 SEAL Rubber Thick SEAL Rubber Thin COLLAR SCREW Set SPRING Compression WASHER CUP Ajquiessy Assembly 8 Figure 2 Remove Deflector and Arbor Cover A Carriage Bolts Washers Lockwashers amp Nuts B Deflector C Arbor Cover Right Hand D Taptite Screws Remove Deflector and Arbor Cover All Models 1 Remove the mower deck from the unit see Operator s Manual for Mower Deck Removal Remove and discard the carriage bolts washers lockwashers nuts A Figure 2 and deflector rod Retain the deflector 2 Remove and discard the taptite screws D and arbor cover C Install the Discharge Baffle 38 MOWER DECKS 1 Install discharge baffle A Figure 3 using 1 4 20 x 3 4 carriage bolt B and 1 4 20 locknut C Do not tighten hardware at this time 2 Install 5 16 18 x 1 1 4 carriage bolt D spacer E bracket F and 5 16 18 locknut G as shown 3 Tighten all hardware 44 AND 50 MOWER DECKS 1 Install discharge baffle A Figure 4 to stone guard G using 5 16 18 x 7 8 capscrew F and 5 16 18 locknut E as shown 2 Install discharge baffle assembly A to mower deck over cover B using 1 4 20 x 3 4 carriage bolt D and 1 4 20 locknut C as shown Do not tighten hardware at this time 3 Install front of cover B Figure 4 to front of mower deck using 1 4 20 x 3 4 carriage bolt D and 1 4 20 locknut C
11. ey c Set the parking brake and wait for all moving parts to stop D Remove the foreign object or clear the chute with a piece of wood before restarting the engine NEVER place hands into blower housing to clear jammed object Blower may rotate when object is removed For added tractor stability and to prevent tipping or loss of control a Use reduced speed on uneven ground and when turning corners b Reduce loads on hillsides It is recommended that the collection system be kept only half full when negotiating any slopes Start mowing on slopes when the collection system is empty c Mow up and down the face of slopes never across the face of any slope 12 Never operate the machine without proper guards plates or other safety protective devices in place 13 Use only attachments and accessories approved of by the manufacturer or the machine wo oon o N Oo oO BR 1 i 1 N CHILDREN Tragic accidents can occur if the operator is not alert to the presence of children Children are often attracted to the unit and the operating activity Never assume that children will remain where you last saw them 1 Keep children out of the work area and under the watchful care of another responsible adult 2 Be alert and turn unit off if children enter the area 3 Never allow children to operate the unit SERVICE AND MAINTENANCE 1 Keep machine attachments and accessories in safe working conditi
12. flector Latch Assembly 38 Mower A Defector Latch Assembly B Capscrews Taptite 5 16 18 x 5 8 C Existing Holes in Mower Deck www SimplicityMfg com www MasseyLawn com www AGCOLawn com www Snapper com Install Turbo Belt and Mounting Latch 1 Select the correct belt for the mower deck used See parts listing on page 6 7 Loosen the hardware securing the drive pulley belt guide B Figure 17 or 18 and the idler pulley C 2 Install the belt as shown in Figure 17 or 18 3 Tighten the hardware securing the drive pulley belt guide B Figure 17 or 18 and the idler pulley C so the idler belt guide is within 1 16 1 59mm of the belt 4 Remove and retain hardware D Figure 17 or 18 See Figure 16 for hole location Install the mounting latch A Figure 17 or 18 reusing hardware D Latch may have to be repositioned later 38 Mounting Hole Location 44 amp 50 Mounting Hole Location Figure 16 Mounting Latch Holes Figure 17 Belt Routing 38 Models A Mounting Latch B Drive Pulley Belt Guide Hardware C Idler Pulley D Hardware Figure 18 Belt Routing 44 and 50 Models A Mounting Bracket B Drive Pulley Belt Guide Hardware C Idler Pulley D Hardware Ajquiessy 13 Assembly 14 nmoom s Fig ure 19 Install Turbo Blower Pivot Pin Deflector Turbo Anchor Bracket Wingnut Pivot Bracket
13. hat will improve footing on slippery surfaces san Read the operating and service instructions carefully Be thoroughly familiar with the controls and the proper use of the equipment Know how to stop the unit and disengage the control quickly 2 Keep the area of operation clear of all persons particularly small children and pets GENERAL OPERATION 1 Know the tractor controls and how to stop quickly READ THE TRACTOR OPERATOR S MANUAL 2 Read and obey all safety decals Only allow responsible adults who are familiar with the instructions to operate the unit Disengage the electric clutch PTO Shut off the engine and wait for all moving parts to stop before attaching adjusting or disconnecting any part of the collection system Check the collection system to make sure it is bolted tightly to the tractor DO NOT operate the mower without either the entire grass catcher or the deflector in place Turn off the PTO switch to disengage the blades when not mowing DO NOT mow in reverse Always look down and behind before and while travelling in reverse DO NOT turn sharply when travelling alongside a building or any object Slow down before turning DO NOT carry passengers on the tractor When blower assembly is removed from the mower deck the deflector must be properly installed If the mower stalls or the turbo blower chute plugs a Disengage the electric clutch PTO b Stop the engine and remove the k
14. ion Numbers When contacting your authorized dealer for replacement parts service or information on the chassis or engine you MUST have these i qp icity Manufacturing Inc numbers bi gton WI 53074 0997 USA Record your model name number manufacturer s MODEL X JXXX XXXX XX XXX identification numbers and engine serial numbers in MATT the space provided for easy access These numbers can be found in the locations shown CE Models Place the extra copy of the identification tag in this manual Attachment Identification Data Model Description Name Number Unit PART Number Unit SERIAL Number 4 www SimplicityMfg com www MasseyLawn com www AGCOLawn com www Snapper com Initial Assembly Figure 1 Package Contents Ajquiessy Assembly 6 ATTACH TO TURBO COVER FLANGE SPRING t 38 MOWER LOADED MOWER IDLER ARBOR Figure 1a Package Contents continued www SimplicityMfg com www MasseyLawn com www AGCOLawn com www Snapper com EET Ne pr E EET URP ONT SNNT AJ d O C1 amp 5 no 11 e 9 09 0 01 00 SD Part No 1722546A 1931277 1718304A 1724376A 1919326 1923325 1931333 1931317 1717291 1732591A 1960685 1732592A 1960318 1732619A 1705064 1919381 1960636 1724374A 1718295 1933896 1960404 1923701 1924940 1714817 1910531 1724373A 1704768A 1931211 1921221 1917356 2172845 1710703 1733078 1603592 1709941 1713623 1960520 1713540 17
15. lectors Edging From the inside of grass catcher slide the thin seal A Figure 30 onto the cover edge B starting at the LH side of the hinge edge D so that the inside curl C is toward the inside of the cover From the inside of grass catcher slide the thick seal A Figure 5 on the cover edge as shown starting at the out side end of the thin seal B and continuing around the cover Figure 29 Install Thick Seal A Thick Seal B Corner LH C Hinge Edge Figure 30 Install Thin Edging A Thin Edging B Cover Edge LH C Inside Curl D Hinge Edge 17 Ajquiessy Assembly 18 Figure 31 Install Thick Seal A Thick Seal B Edge of Thin Seal Snapper Models 1 Place several blocks of wood under the mower deck so that there is slack in the mower lift when the mower is in the lowest position 2 Remove the hair pin F Figure 33 from lift rod A 3 Remove the lift rod A Figure 32 amp 33 from lift bar C 4 Remove the locknut B Figure 33 spacer E 5 Mark the location of the special nut D on lift rod A and remove nut Figure 32 Remove Lift Hod A Lift Rod B Lock Nut C Lift Bar D Special Nut Figure 33 Remove Lift Rod A Lift Rod Locknut Lift Bar Special Nut Spacer Hair Pin nmo www SimplicityMfg com www MasseyLawn com www AGCOLawn com www Snapper com
16. ly P 44 Only Belt Latch Belt Cover 5 16 18 x 1 Capscrew 5 16 Washer Support Bracket 5 16 18 Nut Nylock nmo 10 44 and 50 Models Attach the belt cover B Figure 23 to support bracket E securing with 5 16 18 x 1 capscrew C washer D and 5 16 18 nut CAUTION Before you begin operating the unit with the Turbo attached be certain you have read all of the safety information in this Operator s Manual as well as the Operator s Manual for the tractor and any grass catchers or other collection devices used in conjunction with this turbo blower Install Seal Cover tubes and Turbo 1 Use cover plate A Figure 23 as a template to drill six 13 64 holes C on grass catcher cover B as shown 2 Inside grass catcher cover B Figure 25 place seal D and cover plate A Secure using 10 24 x 3 4 screws C and 10 24 locknuts D Ajquiessy Figure 24 Drill Adapter Plate Holes A Cover Plate B Grass Catcher Cover C New13 64 Hole Locations Figure 25 Install Seal and Cover Plate A B C Screw Phillips 10 24 x 3 4 D Cover Plate Grass Catcher Cover Seal Rubber E Locknuts ESNA 10 24 Assembly 3 Slide upper tube B Figure 26 over lower tube A secure with 10 24 x 3 4 screw C washers D and 10 24 locknut E Note The grass catcher hitch channel and cover must be installed according to the Catcher Operator
17. mooumos A WARNING OPERATION WITHOUT TURBO TUBE AND BAGGER For operation without turbo tube and bagger the mower deflector MUST be properly installed in the down position and retained by the spring latch Turbo amp Tube Removal Place the mower deck in the highest cut position Lift clip C Figure 38 over nut and capscrew and disconnect turbo from intake end of tube assembly Slide the intake end of tube assembly E out of seal A and remove tube assembly 4 Place the mower deck in the highest cut position Pull belt tension lever C Figure 37 away from the discharge opening to remove tension from the belt Remove turbo drive belt Loosen wing nut E Figure 38 and lift deflector B Rotate turbo C away from mower deck an remove Follow the Bagger Operator s Manual for removal of catcher components 21 o 3 E J D 3 o go 5 a D O 3 Copyright O 2006 Simplicity Mfg Inc Port Washington WI USA All rights reserved The Simplicity logo is a registered trademark of Simplicity Mfg Inc Port Washington WI USA Contact Information Simplicity Mfg Inc P O Box 997 500 N Spring St Port Washington WI 53074 0997 www SimplicityMfg com amp Simplicity MANUFACTURING INC 500 N Spring Street PO Box 997 Port Washington WI 53074 0997 www SimplicityMfg com F MASSEY FERGUSON LAWN amp GARDEN EQUIPMENT 500 N Spring Street PO B
18. on 2 Clear debris from machine before each use 3 Always refer to the operating instructions for important details if the machine is to be stored for an extended period The collector bag will deteriorate with time and use Inspect it regularly and replace if it becomes worn 2 www SimplicityMfg com www MasseyLawn com www AGCOLawn com www Snapper com Safety Decals This unit has been designed and manufactured to provide you with the safety and reliability you would expect from an industry leader in outdoor power equipment manufacturing Although reading this manual and the safety instructions it contains will provide you with the necessary basic knowledge to operate this equipment safely and effectively we have placed several safety labels on the unit to remind you of this important information while you are operating your unit All DANGER WARNING CAUTION and instructional messages on your unit should be carefully read and obeyed Personal bodily injury can result when these instructions are not followed The information is for your safety and it is important The safety decals below are on your unit If any of these decals are lost or damaged replace them at once See your local dealer for replacements These labels are easily applied and will act as a constant visual reminder to you and others who may use the equipment to follow the safety instructions necessary for safe effective operation DANGER
19. on belt tension lever C Figure 37 Install the turbo drive belt on pulleys as shown and release the belt tension lever C Follow the Bagger Operator s Manual for installation of catcher components Slide the discharge end of tube assembly A Figure 30 through the seal A This may require some rotating or turning of the discharge end of tube assembly Slide the intake end of tube assembly E over the turbo aligning clip C and nut and capscrew D 10 Lift clip C over nut and capscrew D to secure tube to turbo CAUTION Before you begin operating the unit with the Turbo attached be certain you have read all of the safety information in this Operator s Manual as well as the Operator s Manual for the tractor and any grass catchers or other collection devices used in conjunction with this turbo blower 20 Figure 36 Install Turbo Blower mmootm A Pivot Pin Deflector Turbo Anchor Bracket Wingnut Pivot Bracket Figure 37 Turbo Belt Routing nmo A Turbo Drive Belt Mower Deck Drive Pulley Belt Tension Lever Idler Pulleys Mower Deck Turbo Drive Pulley Turbo Drive Pulley www SimplicityMfg com www MasseyLawn com www AGCOLawn com www Snapper com A Figure 38 Connect Tube to Hood and Turbo Seal Discharge end of Tube Assembly Clip Nut and Capscrew Intake end of Tube Assembly
20. ox 997 Port Washington WI 53074 0997 www MasseyLawn com AGCO LAWN amp GARDEN EQUIPMENT 500 N Spring Street PO Box 997 Port Washington WI 53074 0997 AGCOLawn com gt SNAPPER Simplicity Mfg Inc Snapper Products 535 Macon Street McDonough GA 30253 www Snapper com CE
21. s Manual before proceeding with the next steps 4 Slide the discharge end of tube assembly A Figure 27 through the seal A This may require some rotating or turning of the discharge end of tube assembly 5 Slide the intake end of tube assembly E over the turbo aligning clip C and nut and capscrew D 6 Lift clip C over nut and capscrew to secure tube to turbo Figure 26 Install Tubes Lower Tube Upper Tube Screw Phillips 10 24 x 3 4 Washer Flat Locknut ESNA 10 24 moog m Ps A Figure 27 Connect Tube to Hood and Turbo Seal Discharge end of Tube Assembly Clip Nut and Capscrew Intake end of Tube Assembly mO 16 www SimplicityMfg com www MasseyLawn com www AGCOLawn com www Snapper com Figure 28 Install Deflector Plate A Deflector Plate B Cover C New 7 32 Holes D Screws 410 24 x 3 4 E Locknuts 10 24 Triple Collector Plate and Edging 1 Hold deflector plate A Figure 28 in cover B as shown and mark new hole locations using deflector plate holes as a guide Drill two 7 32 holes in the locations marked in the previous step Secure deflector plate A to cover B using 10 24 x 3 4 screws D and 10 24 locknuts E From the inside of grass catcher slide the thick seal A Figure 29 starting at the LH side of the hinge edge C to the corner B on the cover edge as shown Twin Col
Download Pdf Manuals
Related Search