Sears 580.75133 Washer User Manual
Contents
1. HIGH PRESSURE HOSE FIG 5 GUN AND WAND ASSEMBLY Controls the application of water onto cleaning surface with trigger device Includes safety latch UTILITY BRUSH Used to apply detergent and scrub surface DETERGENT PICKUP TUBE AND FILTER Mixes water and detergent in outlet water flow HIGH PRESSURE OUTLET Connection for high pres sure hose QUICK CONNECT Easy connection for intake water supply HOW TO USE YOUR WASHER IF YOU HAVE ANY PROBLEMS OPERATING YOUR PRESSURE WASHER PLEASE CALL THE PRESSURE WASHER HELPLINE AT 1 800 222 3136 STOPPING YOUR PRESSURE WASHER FIG 6 o ifthe pressure washer is running press the ON OFF switch Fig 6 e Simply shutting OFF washer will not release pres sure in the system Pull the trigger on the spray wand assembly to relieve the pressure in the hose NOTE A small amount of water will squirt out when you release the pressure WAND EXTENSIONS Your high pressure washer comes equipped with a choice of three wand extensions one with an adjustable nozzle Fig 7 one with a utility brush Fig 8 and turbo nozzle Not shown Remove the adjustable nozzle extension if you wish to use the utility brush Attach the Brush Adaptor to the utility brush and then insert the threaded end into the spray gun and hand tighten NOZZLE IN HIGH PUSH NOZZLE FORWARD FOR TWIST NOZZLE TO UTILITY ADAPTOR FIG 7 FIG2. 8 se Llar Cleaning Tips 10 ME Custorner Responsibilities 3 10 0 Utility brush 7 8 Check washer components 10 Operation re Detergent Application 9 W Know Your Pressure Washer 7 Electrical supply 9 Stopping NE 8 Warranty 202212 3 Extension cords 9 To Turn on Washer 9 Extensions wand 8 OrderParts back page a e pat Ground Fault Gun and Wand Assembly 6 8 CONTENTS OF HAR DWARE PACK Parts packed separately in carton Utility Brush and Adaptor High Pressure Hose Quick Connect Cleaning Kit ACCESSORIES AND ATTACHMENTS These accessories and attachments were available when the high pressure washer was purchased They are also available at most Sears retail outlets and service centers Most Sears stores can order these items for you when you provide the model number of your high pressure washer Some of these accessories may not apply to your pressure washer GARDEN HOSE QUICK CONNECT WITH 2 ADAPTORS 71 75187 MULTI PUR ROTATING FLOOR SIDING UTILITY BRUSH KIT POSE HOUSE DECK WASH VEHICLE BOAT DEGREASER BRUSH KIT BRUSH KIT WASH 71 75101 WASH 71 75103 71 75102 71 75199 71 75190 71 75189 71 75100 ASSEMBLY Read these instructions and Operators Manual in its en tirety before you attempt to assemble or operate your new high pressure washer Your high pressure washer has
3. MODEL NO 580 751330 bi i E i i 1100 PSI AT 1 6 GPM CUSTOMER HELPLINE 4 1 800 222 3136 7 ELECTRIC HIGH PRESSURE WASHER DOUBLE INSULATED m HOURS Mon Fri 8 a m to 5 p m CST Assembly e Operation e Customer Responsibilities CAUTION Read and Follow all Safety Rules and Instructions Before Operating This Equipment e Service and Adjustment e Repair Parts SEARS ROEBUCK and CO Hoffman Estates IL 60179 U S A Part No 97068 Revision 1 12 15 95 IMPORTANT SAFETY INSTRUCTIONS Save these instructions A WARNING RISK OF ELECTROCUTION inspect cord before every use Do not use if cord is damaged Keep ail connections dry and off the ground e Do not touch plug with wet hands e Double insulated When servicing use only identical replace ment paris This product shall only be connected to a power supply recap tacle protected by a Ground Fault Circuit Interruptor GFCI Read instruction manual before using A WARNING When using this product basic precautions should al ways be foflowed including the following Read ail instructions before using the product WARNING To reduce the risk of injury close supervision is neces sary when product is used near children e Know how to stop the product and bleed the pressure quickly Be thoroughly familiar with controls Stay alert Watch what you are doing Do not operate
4. 8 HOW TO USE ADJUSTABLE NOZZLE WARNING NEVER ADJUST SPRAY PATTERN WHEN SPRAYING NEVER PUT HANDS IN FRONT OF SPRAY NOZZLE TO ADJUST SPRAY PAT TERN With the adjustable nozzle you can adjust the spray pattern to be either high pressure or low pressure You can also adjust the spray so it is concentrated in a stream pattern or expanded into a fan pattern Use this nozzle to apply detergent e Push the nozzle attachment forward when you wish to adjust the spray to low pressure mode Fig 9 Pull the nozzle backward to achieve high pressure e Twisting the nozzle adjusts the spray pattern from a narrow stream to an expanded stream 4 TWIST NOZZLE TO NARROW PRESSURE MODE LOW PRESSURE MODE AND EXPAND SPRAY STREAM SPRAY STREAM DETERGENT APPLICATION FIG 9 OPERATION APPLYING DETERGENT WITH ADJUSTABLE NOZZLE IMPORTANT USE SOAPS DESIGNED SPECIFICALLY FOR PRESSURE WASHERS HOUSEHOLD DETER GENTS ARE NOT RECOMMENDED IMPORTANT YOU MUST ATTACH ALL HOSES BE FORE YOU START THE PRESSURE WASHER START ING THE PRESSURE WASHER WITHOUT ALL THE HOSES CONNECTED WILL DAMAGE THE PUMP Pressure washers are useful cleaning tools designed to clean almost any surface in two easy steps e The first step involves applying an appropriate deter PM solution to penetrate and loosen grime he detergent is applied at low pressure to avoid splashing overspraying and waste Leave the solution on surface for 3 to 5 min
5. Part No 97068 Revision 1 12 15 95 1100 PSI AT 1 6 GPM ELECTRIC HIGH PRESSURE WASHER DOUBLE INSULATED l Each High Pressure Washer has its own model number The model number for your pressure washer will be found on a decal attached to the unit All parts listed herein may be ordered through Sears Roebuck and Co Service Centers and most Retail Stores WHEN ORDERING REPAIR PARTS ALWAYS GIVE THE FOL LOWING INFORMATION e PRODUCT HIGH PRESSURE WASHER MODEL NUMBER 580 751330 PART NUMBER PART DESCRIPTION Your Sears merchandise has added value when you consider that Sears has service units nationwide staffed with Sears trained technicians pro fessional technicians specifically trained on Sears products having the parts tools and the equipment to ensure that we meet our pledge to you we service what we sell and CO Hoffman Estates IL 60179 U S A Printed in U S A
6. for the most part been assembled at the factory except those parts left unassembled Before you can operate your new high pressure washer you must properly connect the high pressure hose IF YOU HAVE ANY PROBLEMS WITH THE ASSEMBLY OF YOUR PRESSURE WASHER PLEASE CALL THE PRESSURE WASHER HELPLINE AT 1 800 222 3136 TO REMOVE PRESSURE WASHER FROM CARTON o Remove gun and wand assembly from cardboard holder e Remove all other packing material from box before removing your high pressure washer Refer to Page 5 Contents of Hardware Pack for an illustrated listing of all the items included with your pressure washer Become familiar with each piece before assem bling pressure washer Check all contents against illustra tions on Page 5 If any parts are missing or damaged call the Pressure Washer Helpline at 1 800 222 3136 HOW TO SET UP YOUR PRESSURE WASHER e Included with this unit is a quick connect fitting that you attach to the water inlet It can separate into two parts a male connector and a female connector that contains an inlet screen Make sure this screen as well as the intake supply filter is clean Attach the male connector of the quick connect to the intake supply opening on the front of the pump Fig 1 The water supply will be attached to the female connector INTAKE SUPPLY OPENIN MALE CONNECTOR INTAKE SUPPLY FILTER FEMALE CONNECTOR FIG 1 o Unravel high pressure hose and attach to s
7. 580 751330 SERIAL NUMBER DATE OF PURCHASE THE MODEL AND SERIAL NUMBERS WILL BE FOUND ON A DECAL ATTACHED TO THE PRES SURE WASHER YOU SHOULD RECORD BOTH SERIAL NUMBER AND DATE OF PURCHASE AND KEEP IN A SAFE PLACE FOR FUTURE REFERENCE OUTLET PRESSURE 1100 psi FLOW RATE 1 6 gpm DETERGENT MIX Use undiluted detergent DETERGENT RATIO WATER SUPPLY TEMPERATURE Not to exceed 104 F MOTOR Brush type universal RATED VOLTAGE 120 volts CURRENT 13 amperes MAINTENANCE AGREEMENT A Sears Maintenance Agreement is available on this prod uct Contact your nearest Sears store for details CUSTOMER RESPONSIBILITIES o Read and observe the safety rules e Follow regular schedule in maintaining caring for and using your high pressure washer e Follow the instructions under Customer Responsibili ties and Storage sections of this Owners Manual FULL ONE YEAR WARRANTY ON CRAFTSMAN HIGH PRESSURE WASHER For one year from the date of purchase when this Crafisman High Pressure Washer is maintained and operated according to the instructions in the owners manual Sears will repair free of charge any defect in material and workmanship if this washer is used for commercial purposes this warranty applies for only 90 days from the date of purchase If this high pressure washer is used for rental purposes this warranty applies for only 30 days after date of purchase This warranty does not cover Expendable items
8. gent hose and clean if clogged Hose should fit tightly on barbed fitting Examine hose for leaks or tears Replace the filter or hose if either is damaged Check Gun and Wand Examine hose connection and make sure it is secure Test trigger by pressing it and making sure it springs back into place when released Put safety latch in ON position and test trigger You should not be able to press trigger STORAGE PRESSURE WASHER PUMP Water should not remain in the unit for long periods of time Sediments of minerals can deposit on pump parts and freeze pump action After each time you are finished using your pressure washer follow this procedure Flush detergent hose by placing the injector filter into a pail of clear water while running Pressure Washer with nozzle in low pressure mode Flush until you can see clear water flowing through hose Shut off the pressure washer unplug it and let it cool THEN REMOVE ALL HOSES Store the pressure washer and its components in such a way as to protect it from freezing Store in a clean dry area Ideally the unit should be stored in a frost free room Coil the high pressure hose and inspect it for damage Cuts in the hose or fraying of it could result in leaks and loss of pressure Should any damage be found replace the hose DO NOT attempt to repair a damaged hose and use it Replace the hose with the genuine Crafts man part Drain water from hose and properly store it io
9. such as spark plugs and air filters which become wom during normal use epairs necessary because of operator abuse or negligence Including damage resulting from no water being supplied to pump or failure o maintain the equipment according to the instructions contained in the owners manual WARRANTY SERVICE IS AVAILABLE BY RETURNING THE HIGH PRESSURE WASHER TO THE NEAREST SEARS SERVICE CENTER DEPARTMENT THROUGHOUT THE UNITED STATES This warranty gives you specific legal rights and you may also have other righis which vary from state to state SEARS ROEBUCK AND CO D 817 WA Hofiman Estates IL 60179 SAFETY RULES aia canti inicias 2 CUSTOMER RESPONSIBILITIES uu coun zu 10 PRODUCT SPECIFICATIONS Sei STORAGE een 11 CONTENTS OF HARDWARE PACK 5 TROUBLESHOOTING o oo cece entree vente oraranoss 12 ACCESSORIES AND ATTACHEMENTS 0 5 REPLACEMENT PARTS cee cueeeeeun 19717 ASSEMBLY no see anal 6 OPERATION nes 7 10 INDEX A R Accessories 5 a Replacement Parts 13 17 Assembly Checidist EN 6 Hardware Pack 5 ot See Removing from Carton 6 High Pressure Hose 6 7 Set Up een 6 Safety Rules 2 M Siphoning 10 Specifications aa Maintenance Agreement 3 SORGE naeh 11 Nozzle 0 ee eee etd Before starting 9 ee Before each use 10 N oe Troubleshooting 12 C Nozzle adjustable
10. OPERATION e Do not spray flammable liquids Never aim the gun at people animals or plants o For household use For indoor or outdoor use o High pressure stream of fluid that this equipment can produce can pierce skin and its underlying tissues leading to serious injury and possible amputation High pressure spray can cause paint chips or other particles to become airborne and fly at high speeds Always wear eye protection when you use this equipment or when you are in vicinity where the equipment is In use Operate the pressure at no more than the PSI fluid pressure tated for your pressure washer Never move the machine by pulling on high pressure hose Use the handle provided on the top of the unit Use a respirator or mask whenever there is a chance that vapors may be inhaled Read all instructions with the mask so you are certain the mask will provide the necessary protection against inhaling harmful vapors High pressure spray may damage fragile items including glass Do not point spray gun at glass when in the high pressure mode Keep the hose connected to machine or the spray gun while the system is pressurized Disconnecting the hose while the unit is pressurized is dangerous Hold the spray gun firmly in your hand before you start the unit Failure to do so could result in an injury from a whipping spray gun Do not leave the spray gun unattended while the machine is running e Cleaning area shoul
11. T HANDS IN FRONT OF SPRAY NOZZLE TO ADJUST SPRAY PATTERN ALWAYS KEEP HANDS IN THE POSE TION SHOWN IN FIG 9 CAUTION Gun kicks back Use both hands WARNING Risk of injury or injection to persons Do not discharge stream at persons A Check that high pressure hose is attached to pump outlet and that water supply is attached to pump inlet female connector of quick connect Turn ON water Water supply should not exceed 104 F Press trigger on gun and wand assembly to force air from high pressure hose Fig 12 Maintain trigger as shown in Fig 12 and press ON OFF switch FIG 13 CUSTOMER RESPONSIBILITIES GENERAL RECOMMENDATIONS The warranty of the high pressure washer does not cover items that have been subjected to operator abuse or neg ligence To receive full value from the warranty operator must maintain high pressure washer as instructed in this manual BEFORE EACH USE DANGER WATER SPRAYING FROM A LEAK IS CAPABLE OF INJECTING MATERIAL INTO SKIN INSPECT HOSE EACH TIME BEFORE USING iT NEVER REPAIR HIGH PRESSURE HOSE RE PLACE IT WITH ANOTHER HOSE THAT MEETS MINIMUM PRESSURE RATING OF YOUR PRES SURE WASHER 10 IMPORTANT DO NOT RUN PUMP WITHOUT THE WATER SUPPLY CONNECTED AND TURNED ON OR THE PUMP WILL BE DAMAGED SIPHONING We do not recommend that you siphon your water supply from sources other than from connecting to househoid water supply TIPS Init
12. TURN OFF THE UNIT AND COMPLETELY DISCONNECT THE POWER SUPPLY PROBLEM Pressure Washer will not start Pressure Washer does not come up to pressure High pressure spray is irregular No intake of cleaning agent CAUSE No electrical power is available Motor overheats Low voltage Trigger not open Electrical defect Spray gun is in low pressure mode Pump is sucking air Water filter clogged Pump not bled to remove air Pump is defective Nozzle or water supply is restricted Water supply inadequate Wrong nozzle setting Nozzle clogged Detergent hose filter clogged 12 CORRECTION 1 2 Check cable plug power socket and fuse Press trigger of wand to reliave pressure on the unit Allow unit to cool for about 2 min It should run when you tum it ON again Length of extension cord is well beyond 66 feet Contact Sears Service Department Open trigger Contact Sears Sevice Department Adjust nozzie to high pressure mode Water hose must be 1 2 diameter Make sure water supply is ON Make sure water supply is clean Check all connections for leaks or blockage Tum OFF the unit hold trigger in OPEN position to relieve pressure and allow air in line to escape With trigger still in OPEN position tum ON the unit Repeat if necessary Clean filter Switch OFF washer press trigger switch ON washer while pressing trigger R
13. d have adequate slopes and drainage to reduce possibility of a fall due to slippery surfaces e Keep water spray away from electric wiring or fatal electric shock may result Do not by pass any safety device on this machine Do not leave gun in closed position for more than 5 minutes with pressure washer running This could damage pump MAINTENANCE AND STORAGE e Operate and store this unit on a stable surface e Inspect hose each time before using it Check all hoses for cuts leaks abrasions or buiging of cover or damage or movement of couplings if any of these conditions exist replace hose imme diately Never repair high pressure hose Replace it with another hose that meets minimum pressure tating of your pressure washer Storeina clean dry area ideally the unit should be stored in a frost free room SERVICING OF A DOUBLE INSULATED PRODUCT In a double insulated product two systems of insulation are provided instead of grounding No means of grounding is provided on a EUER AAN product nor should a means for grounding be adde Servicing a double Insulated product requires extreme care and knowledge of the system and should be done only by qualified service personnel Replacement parts for a double insulated product must be identical to the parts they replace use only genuine replacement parts A double insulated product Is marked with the words DOUBLE INSULATION or DOUBLE INSULATED The symbol may al
14. epeat if necessary Contact Sears Service Depariment Clean nozzie check hose and screens Tum ON water to full position Operate washer in suction operation with open container Adjust nozzle to low pressure mode Clean nozzle Clean filter in detergent hose CRAFSTMAN ELECTRIC HIGH PRESSURE WASHER 580 751330 ITEM 2 O OO NO U RW PARTNO DESCRIPTION 96154 96155 94313 94314 94315 96156 94316 94317 96157 SCREW 4 REQ MOTOR HOUSING 1 REQ GEAR WHEEL 1 REQ GASKET 1 REQ O RING 1 REQ ROTARY SHAFT SEAL 1 REQ BEARING 1 REQ SWASH PLATE 1 REQ SCREW 1 REQ ITEM 11 12 13 14 15 16 17 18 13 REPAIR PARTS PART NO DESCRIPTION 96158 94307 94308 94309 96159 94310 94312 94311 MOTOR HOUSING 1 REQ CABLE 2 REQ SEAL 1 REQ CELLULAR RUBBER CORD 1 REQ HOUSING COVER 1 REQ INSULATING MAT 1 REQ MOTOR 1 REQ INSULATING MAT 1 REQ CRAFSTMAN ELECTRIC HIGH PRESSURE WASHER 580 751330 REPAIR PARTS CRAFSTMAN ELECTRIC HIGH PRESSURE WASHER 580 751330 REPAIR PARTS ITEM O ON OU PWD MD ND PD m aes h N 20 4 GG A IW DESCRIPTION HOUSING 1 REQ SPILL VALVE 1 REQ SLEEVE 1 REQ SELF TAPPING SCREW 2 REQ SPARE PARTS KIT 1 REQ PUMP COVER 1 REQ 19 3 x 2 4mm O RING 1 REQ NOZZLE INSERT 1 REQ OVAL HEAD SCREW 4 REQ 10 x 2 5mm O RING 3 REQ VALVE 3 REQ 76 x 2m
15. ially clean an area and then check the surface for damage if no damage is found you can assume it is okay to continue cleaning Detergents work best when applied to dry surface For most effective cleaning keep spray nozzle be tween 8 to 24 inches of cleaning surface Allow the detergent to soak in between 3 5 minutes before washing and rinsing For cleaning start at lower portion of area to be washed and work upward using long even overlapping strokes For rinsing push the nozzle sieeve to high pressure and wait for detergent to clear Start at the top of area to be rinsed working down with the same action as for cleaning Never use the garden hose inlet to siphon detergent or wax If you get the spray nozzie too close especially using nie pressure mode you may damage the cleaning surface If you have the spray nozzle too far away the cleaning will not be as effective Do not get closer than 6 inches when cleaning automo bile tires o Check and Clean Quick Connect Screen Remove quick connect and examine the inlet screen on the female connector Clean if clogged or replace the quick connect inlet screen Check High Pressure Hose High pressure hose can develop leaks from wear kinking abuse Check ail hoses for cuts leaks abrasions or bulging of cover or damage or movement of couplings If any of these conditions exist replace hose immediately Check Detergent Hose Examine the filter on the deter
16. m O RING 1 REQ CYLINDER HEAD 1 REQ PISTON 3 REQ HELICAL SPRING 3 REQ HOUSING 1 REQ GROOVED RING 3 REO WASHER 3 REQ GROOVED RING 3 REQ O RING 3 REQ PRESSURE VALVE 3 REQ GASKET 1 REQ Part is included with Pump Repair Kit Part No 94301 15 REPAIR PARTS CRAFSTMAN ELECTRIC HIGH PRESSURE WASHER 580 751330 16 CRAFSTMAN ELECTRIC HIGH PRESSURE WASHER 580 751330 REPAIR PARTS ITEM PARTNO DESCRIPTION 1 94293 COVER 1 REQ 2 94294 FILTER 1 REQ 3 94295 HOSE 1 REQ 4 96150 SCREW 7 REQ 5 94296 ELECTRIC CORD 1 REQ 6 94297 CORD BUSHING 1 REQ 7 94298 SWITCH 1 REQ 8 96151 BRACKET 1 REQ 9 94299 PROTECTING CAP 1 REQ 10 96152 SWITCH FRAME 1 REQ 11 96153 RUBBER BUFFER 4 REQ 12 96016 QUICK DISCONNECT ADAPTOR 1 REQ 13 94300 WATER INLET FILTER 1 REQ 14 95602 WAND EXTENSION 1 REQ 15 95563 SPRAY GUN 1 REQ 16 95604 HIGH PRESSURE HOSE 25 FT 1 REQ 17 88185 UTILITY BRUSH 1 REQ 18 95577 ATTACHMENT ADAPTOR 1 REQ 19 97068 OWNER S MANUAL 1 REQ not shown 20 95566 TURBO WAND 1 REQ 21 96017 QUICK DISCONNECT ADAPTOR MALE 1 REQ 17 OWNER S MANUAL MODEL NO 580 751330 IF YOU NEED REPAIR SERVICE OR PARTS FOR REPAIR SERVICE CALL THIS TOLL FREE NUMBER 1 800 4eREPAIR 1 800 473 7247 FOR REPLACEMENT PARTS INFORMATION AND ORDER ING CALL THIS TOLL FREE NUMBER 1 800 FON PART 1 800 366 7278 SEARS ROEBUCK
17. ok up water supply Fig 12 HIGH PRESSURE HOSE GARDEN HOSE FIG 12 e Adjust nozzle to select high pressure mode see Fig 9 NOTE Detergent will not flow when in the high pressure mode Start washer and work from the top of the surface to the bottom NOTE The high pressure mode is most effective when the tip of the wand is held between 8 to 24 inches from the surface being cleaned BEFORE STARTING PRESSURE WASHER To operate the unit you will need the following e Electrical supply rated for 120 volts at 15 amps e fusing an extension cord observe the following speci fications CABLELENGTH WIREGAUGE Up to 33 ft 10m 14 3 AWG 33t0 66 ft 10m to 20m 12 3 AWG e Use only extension cords that are intended for outside use These extension cords are identified by a marking ACCEPTABLE FOR USE WITH OUTDOOR APPLI ANCES STORE INDOORS WHILE NOT IN USE Use only extension cords having an electrical rating not less than the rating of the product Do not use damaged extension cords Examine extension cord before using and replace if damaged Do not abuse extension cord and do not yank on any cord to disconnect it Keep cord away from heat and sharp edges Always discon nect the extension cord from the receptacle before disconnecting the pressure washer from the extension cord OPERATION TO TURN ON WASHER WARNING NEVER ADJUST SPRAY PATTERN WHEN WATER IS SPRAYING NEVER PU
18. pray gun Fig 2 Tighten with two adjustable wrenches as illus trated Do not try to tighten without holding second nut e Toattach the high pressure hose to the unit Fig 3 push the O ring connector of the hose into the high pressure outlet and then hand tighten until secure e Attach adjustable nozzle extension to spray gun by inserting threaded end of extension into end of spray gun and tightening the extension by hand until it locks in place Fig 4 HIGH PRESSURE N HIGH PRESSURE HOSE FIG 3 FIG 4 CHECKLIST e Check for proper hose connections high pressure and water supply and for tight connections and that there an no kinks cuts or damage to the high pressure ose e Provide proper water supply not to exceed 104 F o Be sure to read Safety Rules and Operation sec tions before using the pressure washer OPERATION KNOW YOUR HIGH PRESSURE WASHER READ THIS OWNER S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR HIGH PRESSURE WASHER Compare the illustrations with your high pressure washer to familiarize yourself with the locations of various controls and adjustments Save this manual for future reference INTAKE SUPPLY OPENING MALE CONNECTOR amp INTAKE SUPPLY FILTER QUICK CONNECT WAND EXTENSION UTILITY BRUSH AND ADAPTOR TURBO NOZZLE DETERGENT PICKUP TUBE AND FILTER B WATER INLET male connector see also Fig A
19. prevent cuts and general wear NOZZLE MAINTENANCE If the nozzle becomes restricted or clogged with foreign materials such as dirt excessive pump pressure may develop A partially clogged nozzle can cause a pulsing sensation during use This generally is not a pump related problem but rather a clogged or partially restricted nozzle if the nozzle becomes clogged or partially restricted imme diately clean the nozzle Disconnect the power supply and tum off the water supply Separate the wand from the gun Remove the nozzle from the end of the wand using a 2mm or 5 64 allen wrench Use apiece of wire or small paper clip to free the foreign ras Fig 14 from clogging or restricting the noz zle Use your water supply to back flush the wand removing additional debris Back flush for 30 seconds to 1 minute Fig 15 Turn wand to stream spray position and move from low to high pressure while flushing Reinstall the nozzle into the wand do not over tighten Reconnect wand to the gun Reconnect the water supply and tum on the water Reconnect the electrical power supply 11 Test the pressure washer by operating in the high and low osition FIG 14 insert wire into nozzle and turn back and forth to clear obstruction FIG 15 TROUBLESHOOTING WARNING MANY OF THE ACTIONS YOU ARE ASKED TO CORRECT ARE PROBLEMS THAT INVOLVE CLEANING A COMPONENT OF THE PRESSURE WASHER WHEN CLEANING ANY PART OF THIS UNIT
20. so be marked on the product EXTENSION CORDS Use only extension cords that are intended for outside use These extension cords are identified by a marking ACCEPTABLE FOR USE WITH OUTDOOR APPLIANCES STORE iNDOORS WHILE NOT IN USE Use only extension cords having an electrical rating not less than the rating of the product Do not use damaged extension cords Examine extension cord before using and replace if damaged Do not abuse extension cord and do not yank on any cord to disconnect it Keep cord away from heat and sharp edges Always disconnect the extension cord from the receptacie bafore disconnecting the pressure washer from the extension cord LOOK FOR THIS SYMBOL TO POINT OUT IMPORTANT SAFETY PRECAUTIONS IT MEANS ATTENTION BECOME ALERT YOUR SAFETY IS INVOLVED CONGRATULATIONS on your purchase of a Sears Crafts man high pressure washer It has been designed engi neered and manufactured to give you the best possible dependability and performance Should you experience any problem you cannot easily remedy please contact your nearest Sears Service Cen ter Department or call the 1 800 number listed on the front of this manual We have competent well trained techni cians and the proper tools to service or repair this unit Please read and retain this manual The instructions will enable you to assemble and maintain your high pressure washer properly Always observe the SAFETY RULES MODEL NUMBER
21. the product when fatigued or under the influence of alcoho or drugs Keep operating area clear of all persons WARNING Risk of injury or injection to persons Do not discharge stream at persons High pressure hose can develop ieaks from wear kinking abuse etc Water spraying from a leak is capable of injecting material into skin Do not point the pressure washer spray at people or animals Do not overreach or stand on unstable support Keep good footing and balance at all times Follow the maintenance instructions specified in the manual e This product shall only be connected to a power supply recep tacle protected by a Ground Fault Circuit Interruptor GFCI This is done to comply with National Electrical Code NFPA 70 and to provide additional protection from risk of electrical shock Save these instructions TRAINING e Locate this pressure washer in areas away from combustible materials combustible fumes or dust Some chemicals or detergents may be harmful if inhaled or ingested causing severe nausea fainting or poisoning The harmful elements may cause property damage or severe Injury e Bo not allow CHILDREN to operate the Pressure Washer at any time PREPARATION Before starting the Pressure Washer in cold weather check all parts of the equipment and be sure ice has not formed there Units with broken or missing parts or without protective housing or cavers should NEVER be operated
22. utes to allow solution to work o The second step involves cleaning the surface you have prepared with the pressure washer and then rinsing it clean To apply detergent follow these steps o Prepare your detergent solution as required by your job e Place small filter of the clear detergent syphon ing tube into the deter gent container Fig 10 Set nozzle to low pres sure mode Detergent cannot be siphoned with nozzle in high pressure mode see Fig 9 e Start washer and apply detergent to a dry surface starting from the bottom and working up e Remove siphon from bottle to stop detergent in low pressure mode NOTE Detergents are most effective applied to a dry surface HOW TO USE UTILITY BRUSH e You can apply detergent with this nozzle As you are applying detergent to surface you want to clean you can also combine the liquid spray with scrubbing to clean very dirty areas e You cannot adjust the spray pattern with this nozzle e Store utility brush on top of handle Fig 11 PRESSURE WASHING RINSING WARNING BE EXTREMELY CAREFUL IF YOU MUST USE PRESSURE WASHER FROM LADDER SCAFFOLDING OR ANY OTHER RELATIVELY UN STABLE LOCATION PRESSURE IN A RUNNING WASHER BUILDS IN THE WAND AS YOU CLIMB WHEN YOU PRESS THE TRIGGER THE RECOIL FROM THE INITIAL SPRAY COULD FORCE YOU TO FALL OR IF YOU ARE TOO CLOSE TO THE CLEANING SURFACE HIGH PRESSURE COULD FORCE YOU OFF CLIMBING APPARATUS e Ho
Download Pdf Manuals
Related Search