Schumacher 200.71990 Power Supply User Manual
Contents
1. Failure to follow instructions may cause damage or an explo sion Read the entire instruction manual before use Always shield your eyes during use and wear safety glasses 2 3 1 3 2 3 3 3 4 3 5 3 6 3 7 3 8 3 9 JUMP STARTER DC POWER SOURCE FEATURES 12V DC Power Outlet ON OFF Power Switch Digital Display Per Display Select Push Button Switch DFAT 5 Replaceable Jaw Battery Clamps 6 Rubber Base 7 Internal Battery Charger Outlet not shown DieHard JUMP STARTING A VEHICLE Warning Failure to follow instructions may cause damage or an explosion Read the entire instruction manual before use Turn the ignition OFF before making cable connections Use in a well ventilated area Keep clear of fan blades belts pulleys and other parts that may cause injury Place the Jump Starter on a flat stable surface near the vehicle battery and away from moving engine parts Make sure the rotary power switch on the front panel is in the O OFF position until clamps are connected to the vehicle battery If plugged into a 110V AC wall outlet disconnect To prevent sparking NEVER allow clamps to touch together or to contact the same piece of metal Clamp the red clamp to the positive terminal of the battery For a negative grounded system Clamp the black clamp to an unpainted and unmoving part of the chas sis or engine block The 3 digit display will show the voltage of the bat2. PURCHASE 1 1 1 2 1 3 1 4 1 5 1 6 1 7 1 8 1 9 1 10 IMPORTANT READ AND SAVE THIS SAFETY AND INSTRUCTION MANUAL IMPORTANT SAFETY INSTRUCTIONS Charge the internal battery immediately upon purchase every 30 days and after every use Use in a well ventilated space Contains a sealed non spillable lead acid battery Must be disposed of properly Someone should be within range of your voice or close enough to come to your aid when you are working near a lead acid battery Have plenty of fresh water and soap nearby in case battery acid contacts your skin clothing or eyes If acid enters the eye area rinse with cold water for at least 10 minutes and get medical help immediately Do not smoke or use matches or cigarette lighters or allow any spark or flame near the battery or engine Never operate the power source unit if it has a damaged lead wire or clamps Have the lead wire replaced by a qualified technician Wear complete eye and clothing protection when working with lead acid batteries Do not permit the internal battery in the jump starter to freeze Never charge a frozen battery WARNING Possible explosion hazard Contact with battery acid may cause severe burns and blindness Keep out of reach of children WARNING Pursuant to California Proposition 65 this product contains chemicals known to the State of California to cause cancer and birth de fects or other reproductive harm WARNING
3. DieHard Jump Starter DC Power Source pe Model No 200 71990 220S CAUTION Read all Safety Rules and Operating Instructions and follow them with each use of this product Sears Roebuck and Co Hoffman Estates IL 60179 U S A 00 99 000867 0109 TABLE OF CONTENTS SECTION PAGE IMPORTANT SAFETY INSTRUCTIONS 1 JUMP STARTER DC POWER SOURCE FEATURES JUMP STARTING A VEHICLE Oo N N DIGITAL DISPLAY CHARGING OF INTERNAL BATTERY WITH BUILT IN 3 AMP CHARGER POWERING A 12V DC DEVICE SPECIFICATIONS TO ORDER AND REPLACE JAWS STORAGE AND MAINTENANCE O aa A O DieHard One Year Full Warranty When operated and maintained according to all supplied instructions if this DieHard product fails due to a defect in material or workmanship within one year from the date of purchase return it to any Sears store or other DieHard outlet in the United States for free replacement This warranty gives you specific legal rights and you may also have other rights which vary from state to state Sears Roebuck and Co Hoffman Estates IL 60179 FOR CUSTOMER ASSISTANCE OR REPLACEMENT PARTS CALL TOLL FREE FROM 7 AM TO 5 00 PM CT MONDAY THROUGH FRIDAY 1 800 SEARS 64 1 800 732 7764 CONTAINS SEALED NON SPILLABLE LEAD ACID BATTERY MUST BE DISPOSED OF PROPERLY WARNING Possible explosion hazard Contact with battery acid may cause severe burns and blindness Keep out of reach of children IMPORTANT CHARGE IMMEDIATELY AFTER
4. d into the charger plug on the left side of the jump starter Extension cord not included must be purchased separately Plug the extension cord into a 120V AC electrical wall outlet CAUTION Operating the Jump Starter while the internal battery is being charged may cause permanent damage to the unit Charging of the internal battery could take up to 48 hours due to the age and condition of the battery At full charge the charger will automatically drop into a float mode and maintain the battery at full charge without dam aging the battery The jump starter can be left plugged into the 120V wall outlet indefinitely to maintain full power NOTE A fully charged battery will read 100 Recharge the jump starter after every use and every month 30 days to extend the battery life If the charger is plugged in for over 48 hours and the battery does not fully charge in this time CHG ERR is shown on the Display The batteries may be getting old and will no longer accept a charge POWERING A 12V DC DEVICE This Jump Starter is a power source for all 12 volt DC accessories that are equipped with a 12V accessory plug The DC accessory outlet has a 15 amp automatic overload protection circuit breaker The breaker will automatically reset after an overload occurs To Operate a 12V DC Device e Open the protective cover of the DC power outlet on the front panel of the Jump Starter e Plug the 12V DC device into the DC power outlet and t
5. gged into a 120V AC electrical wall outlet e Unscrew the fastener securing the cables to the rear of the top jaw e Unscrew the fasteners 2 securing the Copper Jaws to the plastic clamp Remove the jaws and braided cable e Reverse for assembly 9 STORAGE AND MAINTENANCE IMPORTANT e CHARGE IMMEDIATELY AFTER PURCHASE e KEEP FULLY CHARGED Charge the internal battery immediately upon purchase every 30 days and after every use All batteries are affected by temperature The ideal storage temperature is between 40 and 70 degrees Fahrenheit The internal battery will gradually self discharge lose power over time especially in warm environments Leaving the battery in a discharged state may result in permanent battery damage To ensure satisfactory performance and avoid permanent dam age charge the internal battery every month When the jump starter is ON the clamps are live and will produce arcing or sparking if they come in contact with each other To prevent accidental arcing always keep the clamps on the storage holders and the JUMP START ON OFF switch in the O OFF position when not using it to jump start a vehicle
6. isplay can be used to indicate a battery s voltage when connected to a battery or the percentage of charge in the jump starter s internal battery With the switch in the O OFF position connect the clamps to the ve hicle s battery and its voltage is displayed Turn the jump starter s rotary switch to 12V and the combination of both internal and external batteries are shown To read the internal battery s charge status disconnect the clamps from the vehicle s battery with the switch in the O OFF position press the display button to read the percentage of charge left in the internal battery or turn the switch to the 12V position and the voltage level of the internal battery is displayed A fully charged battery will read 100 or 12 8 volts CHARGING OF INTERNAL BATTERY WITH BUILT IN 3 AMP CHARGER IMPORTANT e CHARGE IMMEDIATELY AFTER PURCHASE e KEEP FULLY CHARGED This Jump Starter comes with a sealed non spillable DieHard mainte nance free lead acid battery This internal battery is specifically designed to deliver high power jump starting as well as repetitive deep cycling performance After removing the jump starter from the package for the first time charge it for a minimum of 8 hours before using To charge the Jump Starter internal battery Make sure the rotary power switch on the front panel is in the O OFF position ax 5 2 5 3 5 4 5 5 6 1 Plug at least an 18 gauge AWG extension cor
7. tery Do not connect the clamp to the carburetor fuel lines or sheet metal body parts Connect to a heavy gauge metal part of the frame or engine block If you have connected the clamps backwards an audio alarm will sound DO NOT turn your jump starter on This could cause serious damage Reverse the connections and the audio alarm will stop a2 3 10 3 11 3 12 5 1 If no audio alarm sounds turn the rotary switch to the 12V position The clamps are now powered Crank the engine If the engine does not start within 5 8 seconds stop cranking and wait at least 1 minute before at tempting to start the vehicle again This permits the battery to cool down After the engine starts turn the rotary switch to the O OFF position Then disconnect the black clamp and then the red clamp in that order Store the clamps in the compartments located on the sides of the case Recharge the jump starter as soon as possible after use NOTE In the rare case of jump starting a vehicle that has a positive grounded vehicle electrical system connect the NEGATIVE black clamp to the negative terminal of the vehicle battery Then connect the POSITIVE red clamp to an unpainted and unmoving part of the vehicle chassis or engine block If you are unsure of the nature of the vehicle s electrical grounding system check the owner s manual of the vehicle To disconnect the clamps reverse the order DIGITAL DISPLAY The d
8. urn the 12V DC device ON if required e If the 12V DC device draws more than 15A the internal circuit breaker of the Jump Starter will stop powering the device If this occurs unplug the device and the circuit breaker will automatically reset after several seconds e The DC power outlet is wired directly to the internal battery Extended operation of a 12V DC device may result in excessive battery drain Re charge immediately after unplugging the device 12V DC Electrical Device Example Run Time Chart Appliance Type Estimated Power Estimated Time Fluorescent Lights Cellular Phones 4 Watts Radios Depth Finders Fans 9 Watts NOTE Estimated run times Actual time may vary Times are based on the internal battery being new fully charged and operating at room tem perature 7 SPECIFICATIONS Internal Battery Type DieHard Maintenance Free AGM Lead Acid Nominal Voltage 12V DC Capacity 22Ah DC Power Outlet Max Continuous 15A Load Jumper Cables 4 Gauge 50 Inches Long Battery Clamps Replaceable Jaw Dimensions H x W x D 16 x 14 x 5 Weight 22 Ibs 8 TO ORDER AND REPLACE JAWS Part Number 2299001580 Description Kit Battery Clamp Rebuild QTY Per Clamp 1 8 1 Battery Clamp Jaw Replacement e Secure the clamp in an open position using a vise or equivalent clamping device IMPORTANT Make sure the rotary switch on the front panel is in the O OFF position and the jump starter is not plu
Download Pdf Manuals
Related Search