Sanyo ECD-T1137S CD Player User Manual
Contents
1. Screw Factory radio mounting bracket Dashboard or Console Hook Remove this part Note The mounting box outer trim ring and half sleeve are not used for method B installation HOW TO REMOVE AND INSTALL THE FRONT PANEL OPTIONAL Press the release button and pull off the front panel Store front panel in the case N To install the front panel insert the panel into the housing and make sure the panel is properly installed otherwise abnormalities may occur on the display or some keys may not function properly REMOVING THE FRONT PANEL Front Panel Release Button IR INSTALLING THE FRONT PANEL WIRING CONNECTION GREY MAIN UNIT ANTENNACONNECTOR IGNITION RED SWITCH B MEMORY YELLOW BACK UP RCA CABLE BLACK GROUND B POWER BLUE ANTENNA FRONTLch ME a SPEAKER E WHITE BLACK GREY BLACK GREEN VIOLET REAR Lch a GREEN BLACK VIOLET BLACK Rch RED Lch WHITE FRONT Rch SPEAKER REAR Rch SPEAKER OPERATION GENERAL OPERATION e ON OFF Switch on the unit by pressing any button except 4 button 7 and eject 4 button 4 When system is on press PWR button 9 to turn off the unit e FACEPLATE RELEASE2. Press a button 7 to detach the removable faceplate 6 The adjustment mode will change in the following order r Volume Bass Treble Balance Fader By pressing VOL button 11 or VOL button 12 it is possible to adjust the desired sound level LOUDNESS Press BND LOU button 13 for several seconds to reinforce the bass output and display will show LOUD Press it for several seconds again to release this function SET THE CLOCK Press the DSP button 15 the clock is shown on the LCD display Then hold down the button until the clock flashes Then press the MANU SKIP pbi button 17 to change hours or MANU SKIP button i 16 to change minutes SELECT MODE Press MOD button 6 shortly to choose desired listening mode e g radio mode to CD mode to AUX mode MUTE Press MUT button 3 to mute the sound instantly If any button is pressed in the mute state the mute mode is released LIQUID CRYSTAL DISPLAY Exhibit current frequency and activated functions on the display 8 EQUALIZATION Press EQ button 19 to turn on equalization function and to select desired audio mode There are five kinds of mode as below r FLAT gt CLASSICS gt POP M gt ROCK M gt DSP OFF AUXILIARY INPUT The unit can be connected to a portable audio player through the AUX IN jack 24 To hear the input signal press MOD 6 button several times until the display shows
3. Frequency Coverage Sensitivity S N 20 dB DC 12 Volts Negative Ground 178 W x 165 D x 50 H 10 dB 10 dB 10 dB 10 dB 40W x 4 ch 15 Ampere max More than 55 dB More than 50 dB 40Hz 18 KHz FM 87 5 to 107 9 MHz 10 7 MHz 4uV gt 25dB AM 530 to 1710 KHz 450 KHz 36 dBu TROUBLE SHOOTING Before going through the check list check wiring connection If any of the problems persist after check list has been made consult your near est service dealer Symptom No power Cause The car ignition switch is not on The fuse is blown Solution If the power supply is properly connected to the car accessory circuits but the engine is not running switch the ignition key to ACC Replace the fuse Disc cannot be loaded or ejected Presence of CD disc inside the player Remove the disc in the player then put a new one Disc is upside down Insert the compact disc with the label facing upward Compact disc is extremely dirty or defective disc Clean the disc or try to play a new one Temperature inside the car is too high Cool off or until the ambient temperature returns to normal Condensation Leave the player off for an hour or So then try again more than 30 degrees No sound Volume is in minimum Adjust volume to a desired level Wiring is not properly Check wiring connection connecte
4. AXU FLASHING LED If the front panel is not installed in the main unit the LED 25 will be flashing RESET RESET button 26 can be activated with either a ball point pen or thin metal object RESET button 26 is to be activated for the following reasons Initial installation of the unit when all wiring is completed All the function buttons do not operate Error symbol on the display RADIO OPERATION e BAND SELECTION At tuner mode press BND LOU button 13 to select the desired band The reception band will change in the following order FM1 gt FM2 FM3 AM e STATION SELECTION Press MANU SKIP 44 button 16 or MANU SKIP Pi button 17 to activate automatic seek function To select manual tuning mode press for several seconds until MANUAL appears on the display If both buttons are not pressed for several seconds the tuner will return to seek tuning mode and AUTO will appear on the display e LOCAL DISTANCE Press LOC button 2 to select between local and distant stations Local setting for reception of strong station and a distant setting for reception of weaker stations This function is in effect during AUTO SEEK operation e AUTOMATIC MEMORY STORING amp PROGRAM SCANNING Automatic Memory Storing Press ATP button 18 for several seconds the radio will search from the current station and check the signal strength until one cycle search is finished The 6 strongest stati
5. OWNER S MANUAL SANYO ECD T1137S PLL Synthesized Stereo Radio with Digital Compact Disc Player e 1pair of RCA output e CD R CD R W Compatibility e 4 preset Equalization e Auxiliary Input INSTALLATION Notes e Choose the mounting location where the unit will not interfere with the normal driving function of the driver e Before finally installing the unit connect the wiring temporarily and make sur e it is all connected up properly and the unit and the system works properly e Use only the parts included with the unit to ensure proper installation The use of unauthorized parts can cause malfunctions e Consult with your nearest dealer if installation requires the drilling of holes or other modifications of the vehicle e Install the unit where it does not get in the driver s way and cannot injure the passenger if there is a sudden stop like an emergency stop e If installation angle exceeds 30 from horizontal the unit might not give its optimum performance A 30 e Avoidinstalling the unit where it would be subject to high temperature such as from direct sunlight or from hot air from the heater or where it would be subject to dust dirt or excessive vibration DIN FRONT REAR MOUNT This unit can be properly installed either from Front conventional DIN Front mount or Rear DIN Rear mount installation utilizing threaded screw holes at the sides of the unit chassis For details refer
6. SSIONAL OR COMMERCIAL PURPOSE THE ORIGINAL DATED BILL OF SALE OR SALES SLIP MUST BE SUBMITTED TO THE AUTHORIZED SANYO SERVICE CENTER AT THE TIME WARRANTY SERVICE IS REQUESTED Subject to the OBLIGATIONS above and EXCLUSIONS below SANYO FISHER COMPANY SFC warrants this SANYO product against defects in materials and workmanship for the periods specified below SFC will repair or replace atits option the product and any of its parts which fail to conform to this warranty with new or reconditioned products or parts The warranty period commences on the date the product was first purchased at retail LABOR PARTS 1 YEAR 1 YEAR EXCLUSIONS This warranty does not cover A the adjustment of customer operated controls as explained in the appropriate model instruction manual or B the repair of any product whose serial number has been altered defaced or removed This warranty does not apply to the cabinet or cosmetic parts knobs or routine maintenance This warranty does not apply to the elimination of car static or motor noise correction of antenna problems or damage to compact discs speakers accessories or vehicle electrical systems This warranty does not apply to repairs or replacements necessitated by any cause beyond the control of SFC including but not limited to any malfunction defect or failure caused by or resulting from unauthorized service or parts improper maintenance operation contrary to furnished i
7. d Sound skips The installation angle is Adjust the installation angle less than 30 degrees The disc is extremely dirty or defective disc Clean the compact disc or try to play a new one The operation keys do not work The built in microcomputer is not operating properly due to noise Press the RESET button Make Sure the Front panel is properly fixed into its place The radio does not work The radio station automatic selection does not work The antenna cable is not connected Insert the antenna cable firmly The signals are too weak Select a station manually SANYO MOBILE AUDIO MODEL ECD T1137S LIMITED WARRANTY OBLIGATIONS In order to obtain warranty service the product must be delivered to and picked up from an Authorized Sanyo Factory Service Center at the user s expense unless specifically stated otherwise in this warranty The names and addresses of Authorized Sanyo Service Centers may be obtained by calling the toll free number listed below For product operation authorized service center referral service assistance or problem resolution call CUSTOMER INFORMATION 1 800 421 6382 Weekdays 8 00 AM 5 00 PM Pacific Time THIS WARRANTY IS VALID ONLY ON SANYO PRODUCTS PURCHASED AND USED IN THE UNITED STATES OF AMERICA THIS WARRANTY APPLIES ONLY TO THE ORIGINAL RETAIL USER AND DOES NOT APPLY TO PRODUCTS USED FOR ANY INDUSTRIAL PROFE
8. g to use non standar d shape discs e g square start heart may damage the unit Be sure to use round shape CD discs only for this unit Do not stick paper or tape etc onto the label side or the recording side of any discs as it may cause a malfunction Dirt dust scratches and warping discs will cause misoperation Notes on CD Rs recordable CDs CD RWs rewritable CDs q Be sure to use discs with following marks only for the unit to play COMBAT COMPACT COMPACT de che oise DIGITAL AUDIO DIGITAL AUDIO DIGITAL AUDIO The unit can only play a CD R and CD RW that is finalized Please refer to the manual of your CD R CD RW recorder or CD R CD RW software for more information on finalization process Depending on the recording status conditions of the disc and the equipment used for the recording some CD Rs CD RWs may not play on this unit See 1 To have more reliable play back please see following recommendations Use CD RWs with speed 1x to 4x and write with speed 1x to 2x Use CD Rs with speed 1x to 8x and write with speed 1x to 2x Do not play a CD RW which has been written for mor e than 5 times SPECIFICATION GENERAL Power Supply Requirements Chassis Dimensions Tone Controls Bass at 100 Hz Treble at 10 KHz Maximum Output P ower Current Drain CD PLAYER Signal to Noise Ratio Channel Separation Frequency Response RADIO Frequency Coverage Sensitivity S N 30 dB Stereo Separation
9. nstructions shipping or transit accidents modification or repair by the user abuse misuse neglect accident incorrect power line voltage fire flood or other Acts of God or normal wear and tear The foregoing is in lieu of all other express warranties and SFC does not assume or authorize any party to assume for it any other obligation or liability THE DURATION OF ANY WARRANTIES WHICH MAY BE IMPLIED BY LAW INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS IS LIMITED TO THE TERM OF THIS WARRANTY IN NO EVENT SHALL SFC BE LIABLE FOR SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING FROM OWNERSHIP OR USE OF THIS PRODUCT OR FOR ANY DELAY IN THE PERFORMANCE OF ITS OBLIGATIONS UNDER THIS WARRANTY DUE TO CAUSES BEYOND ITS CONTROL SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS AND OR DO NOT ALLOW THE EXCLUSION OR LIMITATION OF CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATIONS AND EXCLUSIONS MAY NOT APPLY TO YOU THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS YOU MAY HAVE OTHERRIGHTS WHICH VARY FROM STATE TO STATE For your protection in the event of theft or loss of this product please fill in the information below for your own personal records Model No _ Serial No Located on back or bottom side of unit Date of Purchase Purchase Price Where Purchased SANYO 21605 Plummer Street Chatsworth CA91311 ECD T1137S Issue Number 1 Printed in Hong Kong 88 C1007 11
10. ons detected will be stored into the corresponding preset button Program Scanning Press ATP button 18 shortly to scan preset station e STATION STORING Press any one of the preset buttons 14 M1 to M6 to select a station which had been stored in the memory Press this button for several seconds to store the current station into that preset button e SEEK FUNCTION Press SEEK button 1 to scan and hear all tunable stations for a few seconds Press SEEK again to stop at current station CD OPERATION e SELECT TRACKS Press MANU SKIP 144 button 16 or MANU SKIP Pi button 17 to move to the previous track or the following track Track number shows on display Hold MANU SKIP 4 button 16 or MANU SKIP Pi button 17 to fast reverse or fast forward CD play starts from when you release the button e PAUSE PLAYING Press PAU button 20 to pause CD player Press it again to resume play e REPEAT THE SAME TRACK Press RPT button 22 to continuously repeat the same track Press again to stop repeat e PREVIEW ALL TRACKS Press SCN button 21 to play first several seconds of each track on the current disc Press again to stop intro and listen to track e PLAYALL TRACKS IN RANDOM Press SHF button 23 to play all tracks on CD in random order Press again to cancel the function e EJECT Press a eject button 4 to stop CD playing and eject the disc from the disc slot 5 Note A Notes on discs 1 2 Attemptin
11. to the following illustrated installation methods DIN FRONT MOUNT Method A Installation of the unit 1 Dashboard 2 Holder After inserting the holder into the dashboard select the appropriate tab according to the thickness of the dashboard material and bend them inwards to secure the holder in place 3 Screw o o eb Oo NN gt Dashboard Nut 5mm Spring washer Screw 5 x 14mm Screw Strap Be sure to use the strap to secure the back of the unit in place The strap can be bent by hand to the desired angle 1 Frame DIN REAR MOUNT Method B Insert fingers into the groove in the front of frame and pull out to remove the frame When reattaching the frame point the side with a groove downwards and attach it Lever Insert the levers supplied with the unit into the grooves at both sides of the unit as shown in figure until they click Pulling the levers makes it possible to remove the unit from the dashboard Installation using the screw holes on the sides of the unit ou A OO N Fastening the unit to the factory radio mounting bracket 1 Select a position where the screw holes of the bracket and the screw holes of the main unit become aligned are fitted and tighten the screws at 2 places on each side Use either truss screws 5 x 5mm or flush surface screws 4 x 5mm depending on the shape of the screw holes in the bracket
Download Pdf Manuals
Related Search