Home

Samsung 512N Computer Monitor User Manual

1. Caution Use a recommended detergent only as other Surfactants containing large amounts of alcohol solvent or other strong substances can discolor or crack the monitor or damage the coated CDT 6 li the connector between the plug and the pin is dusty or dirty clean it properly with a dry cloth A dirty connector can cause an electric shock or fire 6 Do not set a glass of water chemicals or any small metal objects on the monitor This may cause damage electric shock or a fire If a foreign substance gets into the monitor disconnect the plug and then contact a service center SAMSUNG DIGITal everyone s invitedm User s Manual 8 Safety Instructions Do not remove cover or back No user serviceable parts inside This may cause an electric shock or a fire Refer servicing to qualified service personnel 6 If your monitor does not operate normally in particular if there are any unusual sounds or smells coming from it unplug it immediately and contact an authorized dealer or service This may cause an electric shock or a fire 5 Do not place any heavy objects on the monitor WA cU This may cause an electric shock or a fire D For each hour of looking at the monitor you should let your eyes rest for 5 minutes This will reduce eye fatigue Do not use
2. Dot Pitch 0 24mm Horizontal Screen type Aluminized tri color phosphor dot trio with black matrix Anti doming invar shadow mask Maximum Resolution 1024 Dots 768 Lines 68Hz Active Display Horizontal 267 4 mm Vertical 200 4 mm Horizontal 30 55 kHz Vertical 50 120 Hz Video Signal RGB Analog 0 7 Vpp positive at 75 ohms Sync Signal separate H V sync TTL level positive or negative Unlimited 65 MHz 90 264VAC rms 60 50 Hz 3Hz Power Consumption 80W Maximum 7OW Nominal Dimensions WxDxH 356x 380 x 369 5mm with stand Weight 11 5 kg Environmental Considerations Operating Temperature 32 F 104 F 0 C 40 C Humidity 10 80 non a Storage Temperature 4 F 113 F 20 C 45 C Humidit 5 95 non condensing Plug and Play Capabilit This monitor can be installed on any Plug amp Play compatible system Interaction of the monitor and computer systems will provide the best operating conditions and monitor settings In most cases monitor installation will proceed automatically unless the user wishes to select alternate settings Design and specifications are subject to change without prior notice SAMSUNG DIGITal everyone s invitedw User s Manual 44 Specifications Preset Display Modes If the signal transferred from the computer is the same as the following Preset Display Modes the screen will be adjusted automatically However if the sig
3. Do not drop the monitor when moving it This may cause damage to the product or human body Place the monitor on a flat and stable surface The monitor can cause injury by falling Set down the monitor carefully li could be damaged or broken Do not place the monitor face down The CRT surface may be damaged Do not use the monitor without the monitor stand t could break down or cause a fire due to bad ventilation f the monitor must be used without the supplied stand take steps to insure proper ventilation SAMSUNG DIGITal everyone s invitedm User s Manual Safety Instructions When cleaning the monitor case or the surface of the CDT wipe with a slightly moistened soft fabric Do not clean Flat monitor with water Use a water diluted mild detergent Some detergents contain significant amounts of alcohol based solvents which can damage color change or crack the monitor case The antiglare anti static surface coating on the CDT may also be affected Dilute the detergent 1 10 ratio with water before using 6 Do not spray detergent directly on the monitor Use the recommended detergent with a smooth cloth You can prevent the coated CDT from being damaged or the monitor cabinet from being dissolved cracked or discolored You can buy a recommended detergent at any Samsung Service Center
4. vitedm u Sa wN SAMSUNG DIGITAL everyone s invi SyncMaster 551v 551s Sync Master Monitor Sync Master Monitor Sync Master Monitor Sync Master Monitor Sync Master Monitor SAMSUNG DIGITal everyone s invited Index I Main Page A Safety Instructions gt Power gt Installation gt Cleaning gt Other E introduction G Unpacking Front gt Rear gt Bottom A Setup Connecting Your Monitor gt Installing the Video Driver Windows 2000 Other Operating System Tilt Swivel Base Installation User s Manual LE On Screen Display ey Troubleshooting gt Check List gt Q amp A gt Self Test Feature Check Bl Specifications gt General Specifications Preset Display Modes gt PowerSaver A Information gt Service gt Terms gt Regulatory gt Authority 2 SAMSUNG DIGITal everyone s invitedm User s Manual 3 Safety Instructions Warning Caution Failure to follow directions noted by this symbol could result in bodily harm or damage to equipment Notational Conventions Prohibited Do not disassemble Important to read and understand at all times Disconnect the plug from the outlet Do not touch Grounding to prevent an electric shock 9 SAMSUNG DIGITal everyone s invitedm User s Manual 4 Safety Instructions When not used for extended periods of time set your PC to DPMS If using a scre
5. Pinbalance Adjust the pinbalance setting when the sides of the display are bowed towards the left or right With the menu off push the menu button Push the button or button until the Geometry screen is displayed Push the menu button again and then press the or button until the Pinbalance screen appears Push the menu button to open the Pinbalance adjustment screen Use the button or button to adjust the pinbalance setting V Linearity Adjust the linearity setting when the display image is compressed at the left right or top bottom With the menu off push the menu e button Push the button or button until the Geometry screen is displayed Push the menu button Push the button or button until the V Linearity screen is displayed Push the menu button to open the V Linearity adjustment screen Use the button or button to adjust the vertical linearity SAMSUNG DIGITal everyone s invitedm User s Manual 29 On Screen Display OSD Menu System Menu How to adjust Follow these steps to change the language used in the menu You can choose one of ten languages English German French Italian Portuguese Spanish Swedish Russian Polish or Magyar Some OSD languages may not appear in some areas MD Previous Menu 40 With the menu off push the menu button mM Push the button or button until the Language zn screen is displayed MD Previou
6. button to adjust the pincushion setting Adjust the trapezoid setting when the top or bottom of the display is too large or small With the menu off push the menu button Push the button or button until the Geometry screen is displayed Push the menu button again and then press the or button until the Trapezoid screen appears Push the menu button to open the Trapezoid adjustment screen Use the button or button to adjust the trapezoid setting SAMSUNG DIGITal everyone s invitedm User s Manual 27 On Screen Display OSD Menu System Menu How to adjust Parallelogram Adjust the parallelogram setting when the display is leaning left or right J With the menu off push the menu button HO Exit Menu 7 Push the button or button until the Geometry 4 90 0 screen is displayed o Al 3 Push the menu button again and then press the or button until the Parallelogram screen appears Push the menu button to open the Parallelogram adjustment screen 90 Previous Menu 4 Use the button or button to adjust the parallel setting U Previous Menu SAMSUNG DIGITal everyone s invitedm Users Manual 28 On Screen Display OSD Menu System Menu U Exit Menu or 90 COO 2 agoa g 49D Previous Menu U Previous Menu U Exit Menu 40 BH JD CEC U Previous Menu lt 90 D O B Oe ea S U Previous Menu How to adjust
7. Bio accumulative SAMSUNG DIGITal everyone s invitedm User s Manual 54 Information Authority Information in this document is subject to change without notice 2001 Samsung Electronics Co Ltd All rights reserved Reproduction in any manner whatsoever without the written permission of Samsung Electronics Co Ltd is strictly forbidden Samsung Electronics Co Ltd shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing performance or use of this material Samsung is the registered trademark of Samsung Electronics Co Ltd Microfoft Windows and Windows NT are registered trademark of Microsoft Corporation VESA DPMS and DDC are registered trademarks of Video Electronics Standard Association the ENERGY STAR name and logo are registered trademarks of the U S Environmental Protection Agency EPA As an Energy Star Partner Samsung Electronics Co Ltd has determined that this product meets the ENERGY STAR guidelines for energy efficiency All other product names mentioned herein may be the tradmarks or registered trademarks of their respective owners ELECTRONICS http www samsung monitor com http www samsungmonitor com USA only
8. Daane Aierozolt un recommends that pou stop thit instalation mow and contact the hardware vendor for software that has passed Windows Logo testing Continue Arge _STOP Installation This monitor driver is under certifying MS logo and this installation don t damage your system The certified driver will be posted on Samsung Monitor Homepage http www samsung monitor com 6 Monitor driver installation is completed SAMSUNG DIGITal everyone s invitedw Setup When prompted by the operating system for the monitor driver insert the CD ROM Note included with this monitor Driver installation is slightly different from one operating system to another Follow the directions as appropriate for the operating system you have Prepare a blank disk and download the driver program file at the Internet web site shown here e Internet web site http www samsung monitor com Europe http www samsungmonitor com USA http www sec co kr Korea http www samsungmonitor com cn China Microsoft Windows XP Operating System 1 Insert CD into the CD ROM driver Click Start gt Control Panel then click the Appearance and Themes Icon ir Felge Dear ar an Ly Fig Eee Deere ai k gt Fete FSi bee a HET 155 gt Poe Passe r nn er ic Piako pod os Pie cpa TE er y ee A Ur eg WwW Pairt Prine ann Bae eee pe aa a gt Ye ndoren Modis Mayor 7 ka Mh Fagor Le iets and Lai x
9. This monitor is EPA ENERGY STAR compliant and ENERGY2000 compliant when used with a computer equipped with VESA DPMS functionality As an ENERGY STAR Partner SAMSUNG has determined that this product meets the ENERGY STAR guidelines for energy efficiency SAMSUNG DIGITal everyone s invitedm Information Service U S A Samsung Computer Products Customer Service 400 Valley Road Suite 201 Mt Arlington NJ 07856 Tel 973 601 6000 1 800 SAMSUNG 1 800 726 7864 Fax 973 601 6001 http samsungmonitor com 6 BRAZIL Samsung Eletronica da Amazonia Ltda R Prof Manoelito de Ornellas 303 Terro B Chacara Sto Antonio CEP 04719 040 Sao Paulo SP SAC 0800 124 421 http www samsung com br CANADA Samsung Electronics Canada Inc 7037 Financial Drive Mississauga Ontario L5N 6R3 Tel 1 800 SAMSUNG 1 800 726 7864 Fax 905 542 1199 http www samsung ca 6 COLOMBIA Samsung Electronics Colombia Cra 9 No 99A 02 Of 106 Bogota Colombia Tel 9 800 112 112 Fax 571 618 2068 http www samsung latin com e mail soporte samsung latin com PANAMA Samsung Electronics Latinoamerica Z L S A Calle 50 Edificio Plaza Credicorp Planta Baja Panama Tel 507 210 1122 210 1133 Tel 800 3278 FAST http www samsung latin com PERU Servicio Integral Samsung Av Argentina 1790 Limat Peru Tel 51 1 336 8686 Fax 51 1 336 8551 http www samsungperu com GERMANY TELEPLA
10. cord for your monitor to the power port on the back of the monitor 3 Tilt Swivel Base You can separate the base from the monitor SAMSUNG DIGITal everyone s invited User s Manual 13 Setup Connecting Your Monitor Rear of Monitor ee s Rear of Computer LEITET NANA me rT neni M jimi MO Fb a g F nm 5 i g m 5 p E a E Em a b b g q m 7 5 P 2 g Lie PER pi a ee ee E bo Rear of Macintosh Not included Adapter for Macintosh 1 Connect the power cord for your monitor to the power port on the back of the monitor Plug the power cord for the monitor into a nearby outlet 2 Connect the end of the signal cable to your computer s video port video board video card or graphics card 3 If you are using a Macintosh computer connect the cable to a Macintosh adapter and set the pins on your adapter Adapter not included A PC compatible computer does not need an adapter DAA Turn on your computer and monitor lf your monitor displays an image installation is complete SAMSUNG DIGITal everyone s invitedm Setup Note When prompted by the operating system for the monitor driver insert the CD ROM included with this monitor Driver installation is slightly different from one operating system to another Follow the directions as appropriate for the operating system you have Prepare a blank disk and download the driver program file at the Inter
11. i ele peer ed ee Bra Limhi pija J Sanh Vek Vidoes Fierce Palace sii D ET kun m retna ad u N Wr eran nm 2 tee HP e BR u E E Dies MEK a Control Fanel Icon Peg ar Poy bras ces IO Pepe ll Br See en Crea past DE sii 1 EF iiir iara Hipa 32 Ext w eee jaan a E E EE D EJ D EE ne m Bis ba gpm Eu Sc Dose 4 Click the Properties button on the Monitor tab and select Driver tab Plug and Play Monitor and 30 Prophet iii Properties ma Plug and Play Monitor Properties 2 Gefoced Device Selection I Color Comection Gen Civer Gormal Adapter boria Treubtiechose Color Mans gesrant Moriko tyme oa Phag arki Play Monto m Plug and Play Monitor Data ees ee Maradiacines E ibaan mentor huge dire Loc on 30 Pange IN Jonen naka ara hi mate Bath Hauts En Deine drin The en it arab imag puces TI Hide medes that this re carre deploy Cheating Ms check b aikani pou la dalasi display machen ihai this li pou ane having problems weh thee device click Troubleshoot ba raad ar cannot display ecke This may lesd bo an Lana agih din pasa last us Areale oo an damage ha chwars Dewce usage Lima thee emana rarahan En SAMSUNG DIGITal everyone s invitedm Setup 5 Click Update Driver and select Install from a list or then click Next button Plug and Play Monitor Pioper ies 7 foe Hardware Update Wizard SS ESS Densa Comer ran Welcome to Ihe Hardware Update ee Play araf Flap Mo
12. monitor Do not bend the snap 3 Press the base onto the monitor until the tabs 4 Push the base toward the front of the monitor are fully engaged in the slots until the release latch clicks into the locked position SAMSUNG DIGITal everyone s invitedm User s Manual 21 Setup 3 Removing the Base 5 Squeeze and pull up on the release latch on the base 6 Push the base toward the back of the monitor and lift up to remove the base DAA The Base will align with the monitor slots in only one position SAMSUNG DIGITall User s Manual 22 On Screen Display OSD Menu System 1 Use this button to open the OSD and activate a highlighted menu item 2 3 Use these buttons to highlight and adjust items using the On Screen Display These buttons are also direct access buttons for the contrast and brightness feature 4 Use this button to Exit the active menu or the OSD SAMSUNG DIGITal everyone s invitedm User s Manual 23 On Screen Display OSD Menu System Menu U Exit Menu O0 O B con eo ial 0 O U Previous Menu U Exit Menu 40 QO U Previous Menu How to adjust Brightness Adjust the Brightness J With the menu off push the menu button 2 Push the button or button until the Brightness screen is displayed 3 Push the menu button to open the Brightness adjustment screen 4 Use the button to increase the brightness or button to decrease th
13. or store inflammable substances near the monitor This may cause an explosion or fire Do not try to move the monitor by pulling on the wire or the signal cable This may cause a breakdown electric shock or a fire due to damage to the cable SAMSUNG DIGITal everyone s invitedm User s Manual 9 Safety Instructions Do not move the monitor right or left by pulling only the wire or the signal cable This may cause a breakdown electric shock or a fire due to damage to the cable Never insert anything metallic into the monitor openings This may cause an electric shock fire or injury Keep the monitor away from any magnetic substances This may cause discoloring or distortion of the image SAMSUNG DIGITal everyone s invitedm Introduction W Monitor and Stand Some models include a stand attached Please make sure the following items are included with your monitor If any items are missing contact your dealer Users Manual 10 W Power Cord 7 D W Quick Setup Guide 7 arena card Not available in all locations KA a User s Guide and Driver Installation CD le E USB Option SAMSUNG DIGITal everyone s invitedw User s Manual 11 Introduction 1 Exit button Use this button to Exit the active menu or the OSD 2 3 Adjust buttons These buttons allow you to highlight and
14. D Toa Na Click Start Setting Control Panel Double click Display icon Select the Settings tab and click Advanced Properties button Select the Monitor tab Click the Change button in the Monitor Type area then click Next button Choose Display a list of all the driver then click Next button Click the Have Disk button then click browse button Specify A D driver then click OK button The Select Device dialogue box will appear Select Show all devices then choose the monitor that corresponds to the one you connected to your computer and click OK Continue choosing Close button and O K button until you close the Display Properties dialogue box Microsoft Windows 95 Operating System First determine the Windows 95 version installed on your computer by right clicking the My Computer icon on PC and selecting Properties The version number is listed under System Perform the steps for the appropriate version Version 4 00 950A 1 Click Start Settings Control Panel and then double click Display icon 2 Inthe Display Properties window click the Settings tab and click Change Display Type 3 In the Change Display Type window click Change and then click Have Disk 4 Click browse button and specify A D driver and click OK 5 In the Select Device window click the appropriate monitor model and then click OK 6 Continue choosing Close butto
15. D and perform a Degauss e Keep the monitor away from any magnetic products e Adjust the frequency properly by referring to the video card manual and the Preset Display Modes The maximum frequency per resolution may differ from product to product e For Windows 98 95 Set the colors properly at the Control Panel Display Settings e For Windows 3 1 Adjust the colors of the screen using the VGA utility provided by the video card Set the video card by referring to the video card manual e Install the monitor driver according to the Driver Installation Instructions e Install the monitor driver according to the Driver Installation Instructions SAMSUNG DIGITal everyone s invitedw User s Manual 38 Troubleshooting Check the following items if there is trouble with the monitor 1 Check if the power cord and the cable are properly connected to the computer 2 Check if the computer beeps more than 3 times when booting If it does request an after service for the main board of the computer 3 If you installed a new video card or if you assembled the PC check if the installed the adapter video driver and the monitor driver 4 Check if the scanning ratio of the video screen is set at 75Hz or 85Hz Do not exceed 60Hz when using the maximum resolution 5 If you have problems in installing the adapter video driver boot the computer in Safe Mode remove the Display Adapter at the Control Pan
16. Gustavo A Madero C P 07700 Mexico D F Tel 01 57 47 51 00 Fax 01 57 47 52 02 RFC SEM950215598 http www samsung com mx IMPORTADO POR SAMSUNG ELECTRONICS MEXICO S A DE C V SATURNO 44 COL NVA INDUSTRIAL VALLEJO DEL GUSTAVO A MADERO C P 07700 MEXICO D F TEL 5747 5100 RFC SEM950215598 SAMSUNG ELECTRONICS CO LTD JOONG ANG DAILY NEWS BLDG 7 SOON WHA DONG CHUNG KU C P O BOX 2775 1144 SEOUL KOREA EXPORTADO POR SAMSUNG DIGITal everyone s invitedm User s Manual 4f Information Terms Dot Pitch The image on a monitor is composed of red green and blue dots The closer the dots the higher the resolution The distance between two dots of the same color is called the Dot Pitch Unit mm 6 Vertical Frequency The screen must be redrawn several times per second in order to create and display an image for the user The frequency of this repetition per second is called Vertical Frequency or Refresh Rate Unit Hz Example Ifthe same light repeats itself 60 times per second this is regarded as 60 Hz In this case flickering of the screen can be detected To avoid this problem there is a Flicker free Mode using a vertical frequency over 70 Hz 6 Horizontal Frequency The time to scan one line connecting the right edge to the left edge of the screen horizontally is called Horizontal Cycle The inverse number of the Horizontal Cycle is called Horizontal Frequency Unit kHz 6 Interlace and Non I
17. N Rhein Main GmbH Feldstr 16 64331 Weiterstadt T 06151 957 1306 F 06151 957 1732 http www samsung de AUSTRALIA Samsung Electronics Australia Pty Ltd Customer Response Centre 7 Parkview Drive Homebush Bay NSW 2127 Tel 1300 362 603 http www samsung com au 6 ITALY Samsung Electronics Italia SpA Via C Donat Cattin 5 20063 Cernusco sul Naviglio Mi Tel 167 010740 http www samsung italia com ESPANA Samsung Electronics Comercial Iberica S A Ciencies 55 65 Poligono Pedrosa 08908 Hospitalet de Llobregat Barcelona Tel 93 261 67 00 Fax 93 261 67 50 http samsung es 6 United Kingdom Samsung Electronics UK Ltd Samsung House 225 Hook Rise South Surbiton Surrey KT6 7LD Tel 0208 391 0168 Fax 0208 397 9949 lt European Service Center amp National Service gt Stafford Park 12 Telford Shropshire TF3 3BJ Tel 0870 242 0303 Fax 01952 292 033 http samsungservice co uk 6 THAILAND HAI SAMSUNG SERVICE CENTER MPA COMPLEX BUILDING 1st 2nd Floor 175 SOI SUEKSA VIDHAYA SATHON SOI 12 SILOM ROAD SILOM BANGRAK BANGKOK 10500 TEL 0 2635 2567 FAX 0 2635 2556 Users Manual 46 SOUTH AFRICA Samsung Electronics 5 Libertas Road Somerset Office Park Bryanston Ext 16 Po Box 70006 Bryanston 2021 South Africa Tel 0027 11 549 1621 Fax 0027 11 549 1629 http www samsung co za UKRAINE SAMSUNG ELECTRONICS REPRESENTATIVE OFFICE IN UKRAINE 4 Glybochitska str Kiev Ukra
18. a Gnchiantes 1 TUA TPS NS Hager aptes je if CE Feet te diria ir act cl SenchMasioer 17157 1 7557 1 705 MagiciwnchMacter CH Flug and Play Monitor and Mr Prophet NM Proportion Gene ol Dura Saroblari 17154179554 1705 Hager a 1753 Dias Pros Gare ines Dates AUTANT Dre es paca 10 00 Digia 5 ipri Hot feg pigre Drea Dolai To vima dead about the cree films Tr IF hem daston Pose atar ngekang Han ire roll L HA Back Drive kra kalika caver back io Ihe ge ce Uriba To Lewat all the crea care Chore Monitor driver installation is completed ann Ou See N Microsoft Windows 2000 Operating System When you can see Digital Signature Not Found on your monitor follow these steps Choose OK button on the Insert disk window Click the Browse button on the File Needed window Choose A D Driver then click the Open button and then click OK button How to install Click Start Setting Control Panel Double click the Display Icon Choose the Settings tab and then click Advanced Choose Monitor Case1 If the Properties button is inactive it means your monitor is properly configured Please stop installation Case2 If the Properties button is active click the Properties button then follow next steps continually Click Driver and then click on Update Driver then click on the Next button Choose Display a list of the know
19. able Deflection angle 90 Dot Pitch 0 24mm Horizontal Screen type Aluminized tri color phosphor dot trio with black matrix Anti doming invar shadow mask Glare ESF Maximum Resolution 1024 Dots 768 Lines 68Hz Active Display Horizontal 267 4 mm Vertical 200 4 mm Horizontal 30 55 kHz Vertical 50 120 Hz Video Signal RGB Analog 0 7 Vpp positive at 75 ohms Sync Signal separate H V sync TTL level positive or negative Unlimited 65MHz 90 264VAC rms 60 50 Hz 3Hz Power Consumption 80 W Max 70 W Nom Dimensions WxDxH 356x 380 x 369 5mm with stand Weight 11 5 kg Environmental Considerations Operating Temperature 32 F 104 F 0 C 40 C Humidity 10 80 non a Storage Temperature 4 F 113 F 20 C 45 C Humidit 5 95 non condensing Plug and Play Capabilit This monitor can be installed on any Plug amp Play compatible system Interaction of the monitor and computer systems will provide the best operating conditions and monitor settings In most cases monitor installation will proceed automatically unless the user wishes to select alternate settings Design and specifications are subject to change without prior notice SAMSUNG DIGITal everyone s invitedm User s Manual 43 Specifications General Specifications General Model Name SyncMaster 551s Picture Tube Type 15 38cm Full square type 35cm viewable Deflection angle 90
20. adjust items in the menu 4 Menu button Use this button to open the OSD and activate a highlighted menu item 5 Power indicator This light glows green during normal operation and grows green when you are making adjustments 6 Power button Use this button to turn the monitor on and off Note See PowerSaver described in the manual for further information regarding power saving functions For energy conservation turn your monitor OFF when it is not needed or when leaving it unattended for long periods SAMSUNG DIGITal everyone s invitedm User s Manual 12 Introduction 1 Power port Connect the power cord for your monitor to the power port on the back MINDED Coes MAH of the monitor aa 2 Signal cable Connect the end of the signal cable BEE Ser to your computer s video port tn AN video board video card or graphics ian nana AA card See Connecting Your Monitor for further information regarding cable connections The configuration at the back of the moniter may vary from product to product 2 TH AP a N ww TTT MT AIR LUI Iii i Ill IE II iIi TUWIN ll Wii ili IK ill 1E iil li nun ae 7T i li rte i li dE il ie Wa 9 10 Si ESS ee ss ss Anne Hn My In fai TET NAK NANA JI JE fo sity 1 Signal cable Connect the end of the signal cable to your computer s video port video board video card or graphics card 2 Power port Connect the power
21. atteries relays and switches It damages the nervous system and is toxic in high doses The relevant TCO 99 requirement states that batteries may not contain any mercury It also demands that mercury is not present in any of the electrical or electronics components associated with the labelled unit There is however one exception Mercury is for the time being permitted in the back light system of flat panel monitors as today there is no commercially available alternative TCO aims on removing this exception when a Mercury free alternative is available SAMSUNG DIGITal everyone s invitedw User s Manual 53 Information CFCs freons The relevant TCO 99 requirement states that neither CFCs nor HCFCs may be used during the manufacture and assembly of the product CFCs freons are sometimes used for washing printed circuit boards CFCs break down ozone and thereby damage the ozone layer in the stratosphere causing increased reception on earth of ultraviolet light with e g increased risks of skin cancer malignant melanoma as a consequence Lead Lead can be found in picture tubes display screens solders and capacitors Lead damages the nervous system and in higher doses causes lead poisoning The relevant TCO 99 requirement permits the inclusion of lead since no replacement has yet been developed Bio accumulative is defined as substances which accumulate within living organisms Lead Cadmium and Mercury are heavy metals which are
22. d How to Identify and Resolve Radio TV Interference Problems helpful This booklet was prepared by the Federal Communications Commission It is available from the U S Government Printing Office Washington DC 20402 Stock Number 004 000 00345 4 Warning User must use shielded signal interface cables to maintain FCC compliance for the product Declaration of conformity for products Marked with FCC Logo This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesire operation The party responsible for product compliance SAMSUNG ELECTRONICS CO LTD America QA Lab of Samsung 85 West Tasman Drive San Jose CA 95134 USA Tel 408 544 5124 Fax 408 544 5191 SAMSUNG DIGITal everyone s invitedm User s Manual 49 Information Provided with this monitor is a detachable power supply cord with IEC320 style terminations It may be suitable for connection to any UL Listed personal computer with similar configuration Before making the connection make sure the voltage rating of the computer convenience outlet is the same as the monitor and that the ampere rating of the computer convenience outlet is equal to or exceeds the monitor voltage rating For 120 Volt applications use only UL Listed detachable power cord with NEMA configuration 5 15P type pa
23. d gt DES 3 Push the menu button again and then press the or button until the Video Input Level screen appears Push the menu button to open the Video Input Level selection screen a sere vious iene ZL Use the button or button to select 0 7 V or 1 0 V U Previous Menu Color Temperature Color temperature is a measure of the warmth of the image colors The available range is between 6500 to 9300K MD Exit Menu J With the menu off push the menu button lt o 090 Push the button or button until the Advanced d OS screen is displayed 3 Push the menu button again and then press the or button until the Color Temperature screen appears Push the menu button to open the Color Temperature selection screen D Previous Menu ao 9 0 E MERS 0 Previous Menu Press the or button to select 9300K Bluish colors or 6500K Reddish colors SAMSUNG DIGITal en een Users Manual 32 On Screen Display OSD Menu System Menu How to adjust Follow these instructions to get a close up or a longshot view of the monitor s viewing area J With the menu off push the menu e button Push the button or button until the Zoom screen is displayed U Exit Menu 2 lt 7 0G Push the menu button to open the Zoom adjustment screen Sem 3 p j 4 Use the button to decrease the screen viewing area Use the button to enlarge the screen viewing a
24. dapted electronics products This product meets the requirements for the TCO 99 scheme which provides for an international environmental and quality labelling labelling of personal computers The labelling scheme was developed as a joint effort by the TCO The Swedish Confederation of Professional Employees Svenska Naturskyddsforeningen The Swedish Society for Nature Conservation Statens Energimyndighet The Swedish National Energy Administration and SEMKO AB SAMSUNG DIGITal everyone s invitedw User s Manual 52 Information The requirements cover a wide range of issuse environment ergonomics usability reduction of electric and magnetic fields energy consumption and electrical safet Why do we have environmentally labelled computers In many countries environmental labelling has become an established method for encouraging the adaptation of goods and services to the environment The main problem as far as computers and other electronics equipment are concerned is that environmentally harmful substances are used both in the products and during their manufacture Since it is not so far possible to satisfactorily recycle the majority of electronics equipment most of these potentially damaging substances sooner or later enter nature There are also other characteristics of a computer such as energy consumption levels that are important from the viewpoints of both the work internal and natural external environments Since all method
25. e brightness Adjust the Contrast J With the menu off push the menu button 2 Push the button or button until the Contrast screen is displayed 3 Push the menu button to open the Contrast adjustment screen 4 Use the button to increase the contrast or button to decrease the contrast SAMSUNG DIGITal everyone s invitedm User s Manual DA On Screen Display OSD Menu System Menu 49D Exit Menu lt 0 2 u eo Previous Menu 99D Exit Menu cr 90 0 De El 49D Previous Menu How to adjust Follow these instructions to change the Position of the monitor s entire display I FH amp N With the menu off push the menu e button Push the button or button until the H Position screen is displayed Push the menu e button to open the H Position adjustment screen Use the and buttons to change the Horizontal position of the monitor s viewing area Follow these instructions to change the Position of the monitor s entire display I 2 3 4 With the menu off push the menu e button Push the button or button until the V Position screen is displayed Push the menu button to open the V Position adjustment screen Use the and buttons to change the vertical position of the monitor s viewing area SAMSUNG DIGITal everyone s invitedm User s Manual 25 On Screen Display OSD Menu System Menu How to adj
26. e the monitor and restore the image on the screen e Unlock the OSD by pressing the MENU button for at least 10 seconds SAMSUNG DIGITal everyone s invitedw User s Manual 36 Troubleshooting Chek List Solution Check the monitor configuration to see if it is in Interlace Mode Interlace Mode Vertical frequency 43Hz 87Hz i etc The image on the screen is shaking The signal from the video card exceeds the maximum resolution and frequency of the monitor Move the monitor away from anything that can create a strong magnetic field Are there any magnetic products such as a high voltage wire near by The screen image can appear to Is the voltage stable shake or vibrate at a particular time of day due to low supply voltage The screen image can also appear to shake or vibrate if there is a problem with the video card or the computer s main board The screen Shows js the screen displaying only one e Check the signal cable connection strange colors or color as if looking at the screen just black and through a cellophane paper white Make sure the video card is fully inserted in it s slot Have the screen colors become e Reboot the computer Strange after running a program or due to a crash between applications Has the video card been set properly Set the video card by referring to the video card manual The screen Have you changed the video card or e Adju
27. el System Device Administrator and then reboot the computer to reinstall the adapter video driver DES If problems repeatedly occur contact an authorized service center SAMSUNG DIGITal everyone s invitedw Troubleshooting Q amp A Question How can change the frequency How can adjust the resolution How can set the Power Saving function The monitor makes a sound when it is turned on How can clean the outer case Picture tube Users Manual 39 Frequency can be changed by reconfiguring the video card Note that video card support can vary depending on the version of the driver used Refer to the computer or the video card manual for details Windows 95 98 Set the resolution at the Control Panel Display Settings Windows 3 1 Change the resolution and the colors using the VGA Utility provided by the video card Contact the video card manufacturer for details Windows 95 98 Set the function at BIOS SETUP of the computer or the screen saver Refer to Windows Computer Manual Windows 3 1 Set the function using the VGA Utility provided by the video card This is normal as some sound may be generated when the metal case and the electromagnet which are installed to block any electromagnetic waves interact with each other Disconnect the power cord and then clean the monitor with a soft cloth using either a plain water Do not leave any remains of the detergent nor scratch t
28. en saver set it to the active screen mode lf the size of your monitor is small or if the same image is present for long periods of time you may see afterimages due to damage to the flourescent substance on the inside of the CDT Do not use a damaged or loose plug This may cause an electric shock or fire 6 Do not pull the plug out by the wire nor touch the plug with wet hands This may cause an electric shock or fire Use only a properly grounded plug and recepticle An improper ground may cause electric shock or equipment damage Do not excessively bend the plug and wire nor place heavy objects upon them which could cause damage Failure to do so may cause an electric shock or fire SAMSUNG DIGITal everyone s invitedm User s Manual 5 Safety Instructions Disconnect the plug from the outlet during storms or lightening or if it is not used for a long period of time Failure to do so may cause an electric shock or fire Do not connect too many extension cords or plugs to an outlet This may cause a fire SAMSUNG DIGITal everyone s invitedm User s Manual 6 Safety Instructions Installation Do not cover the vents on the monitor cabinet Bad ventilation may cause a breakdown or fire Put your monitor in a location with low humidity and a minimum of dust An electric shock or fire could result inside the monitor
29. eset All other settings will remain the same 07 181 7 e E This operation resets all of the data in the user memory area for the current timing signal SAMSUNG DIGITal everyone s invitedm Users Manual 34 On Screen Display OSD Menu System Menu U Exit Menu 4 0 D E 909 U Previous Menu 47 D OO 2 ABS HM Previous Menu Control Lock Control Lock How to adjust Display Timing The information on this screen shows Display Timing User Timing and Factory Timing J With the menu off push the menu button 2 Push the button or button until the Display Timing screen is displayed 3 Push the menu button to open the Display Timing adjustment screen 4 Use the button to see user control mode and thedefault mode MA You can see the frequency user control mode used by the user the polarity of the operational signals the default frequency default mode set when you buy the monitor and the resolution level OSD Lock Unlock J Push and hold in the menu button for 10 seconds or more to Lock the OSD In this case even if you click the menu button the control screen will not be printed 7 Push and hold in the menu J button for 10 seconds or more to Unlock the OSD SAMSUNG DIGITal everyone s invitedm Troubleshooting Users Manual 35 Before calling for service check the information in this section to see if you can solve the problem
30. he case Do not allow any water to go inside the monitor everyone s invitedm SAMSUNG DIGITal e Users Manual 40 Troubleshooting A self test feature is provided that allows you to check for proper monitor function If your monitor and computer are properly connected but the monitor screen remains dark and the power indicator is blinking run the monitor self test by performing the following steps Self Test Feature Check 1 Turn off both your computer and the monitor 2 Unplug the video cable from the back of the computer 3 Turn on the monitor If the monitor is functioning properly you will see a cyan box with a red border and black text inside as shown in the following illustration The three boxes inside the border are red green and blue No Connection Failure of any of the boxes to appear indicates a problem with your monitor This box also appears during normal operation if the video cable becomes disconnected or damaged 4 Turn off your monitor and reconnect the video cable then turn on both your computer and the monitor lf your monitor screen remains blank after using the previous procedure check your video controller and computer system your monitor is functioning properly SAMSUNG DIGITal everyone s invitedm User s Manual 4 1 Troubleshooting Warning Messages lf there is something wrong with the input signal a message appears on the screen or the screen goes blank although the power indica
31. ine Tel 8 044 4906878 Fax 8 044 4906887 Toll free 8 800 502 0000 www samsung com ua 6 SWEDEN DENMARK NORWAY FINLAND Samsung Electronics AB Box 713 S 194 27 UPPLANDS VASBY SVERIGE Bes ksadress Johanneslundsvagen 4 Samsung support Sverige 020 46 46 46 Samsung support Danmark 8088 4646 Samsung support Norge 8001 1800 Samsung support Finland 0800 118001 Tel 46 8 590 966 00 Fax 46 8 590 966 50 http www samsung se HUNGARY Samsung Electronics Magyar Rt 1039 Budapest Lehel u 15 17 Tel 36 1 453 1100 Fax 36 1 453 1101 http www samsung hu FRANCE SAMSUNG ELECTRONICS FRANCE Service Paris Nord 2 66 rue des Vanesses BP 50116 Villepinte 95950 Roissy CDG Cedex Tel 08 25 08 65 65 Fax 01 48 63 06 38 http www samsungservices com PORTUGAL SAMSUNG ELECTRONICA PORTUGUESA S A Rua Mario Dioniso N 2 1 Dri 2795 140 LINDA A VELHA Tel 214 148 114 100 Fax 214 148 133 128 Free Line 800 220 120 http www samsung pt NETHERLANDS BELGIUM LUXEMBOURG Samsung Electronics Benelux B V Fleminglaan 12 2289 CP Rijiswijk NEDERLANDS Service and informatielijn Belgium 0800 95214 http www samsung be Netherlands 0800 2295214 http www samsung nl CHILE SONDA S A Teatinos 550 Santiago Centro Santiago Chile Fono 56 2 5605000 Fax 56 2 5605353 56 2 80020021 1 http www sonda com http www samsung cl 6 MEXICO Samsung Electronics Mexico S A de C V Saturno 44 Col Nueva Industrial Vallejo Del
32. ing System To execute X Window you need to make the X86Config file which is a type of system setting file Press Enter at the first and the second screen after executing the X86Config file The third screen is for setting your mouse Set a mouse for your computer The next screen is for selecting a keyboard Set a Keyboard for your computer The next screen is for setting your monitor First of all set a horizontal frequency for your monitor You can enter the frequency directly Set a vertical frequency for your monitor You can enter the frequency directly Enter the model name of your monitor This information will not affect the actual execution of X Window 10 You have finished setting up your monitor Execute X Window after setting other requested hardware SoS oye Oo SAMSUNG DIGITal everyone s invited User s Manual 19 Setup Tilt Swivel Base Installation 1 Tilt Swivel Base With the built in pedestal you can tilt and or swivel the monitor for the most comfortable viewing angle DAA The base is detachable SAMSUNG DIGITal everyone s invitedm Users Manual 20 Setup 2 Attaching the Base lf your monitor was supplied with the base detached attach the base as follows Remove the twist tie before attaching the base to the monitor 1 Place the monitor upside down on a flat 2 Align the tabs on the base with the corresponding work surface slots on the bottom of the
33. lm Sweden Fax 46 8 782 92 07 E mail Internet development tco se Current information regarding TCO 95 approved and labelled products may also be obtained via the Internet using the address http www tco info com TCO 95 is a co operative project between 3 logos SAMSUNG DIGITal everyone s invitedw User s Manual 51 Information Environmental Requirements Brominated flame retardants are present in printed circuit boards cables wires casings and housings In turn they delay the spread of fire Up to thirty percent of the plastic in a computer casing can consist of flame retardant substances These are related to another group of environmental toxins PCBs which are suspected to give rise to similar harm including reproductive damage in fish eating birds and mammals due to the bioaccumulative processes Flame retardants have been found in human blood and researchers fear that disturbances in foetus development may occur 6 1C0 95 demand requires that plastic components weighing more than 25 grams must not contain organically bound chlorine and bromine Lead Lead can be found in picture tubes display screens solders and capacitors Lead damages the nervous system and in higher doses causes lead poisoning 6 TCO 95 requirement Permits the inclusion of lead since no replacement has yet been developed Cadmium Cadmium is present in rechargeable batteries and in the colour generating layers of certain computer displa
34. n and OK button until you close the Display Properties dialogue box Version 4 00 950B 1 Click Start Settings Control Panel and then double click Display icon 2 Inthe Display Properties window click the Settings tab and then click Advanced Properties button 3 In the Advanced Display Properties window click the Monitor tab and then click Change button 4 Inthe Select Device window click Have Disk button 5 Click browse button and specify A D driver and click OK 6 In the Select Device window click the appropriate monitor model and then click OK SAMSUNG DIGITal everyone s invitedm Setup 7 Continue choosing Close button and OK button until you close the Display Properties dialogue box 4 Microsoft Windows NT Operating System 1 Click Start Settings Control Panel and then double click Display icon 2 In Display Registration Information window click Settings Tab and then click All Display Modes 3 Select a mode that you wish to use Resolution Number of colors and Vertical frequency and then click OK 4 Click Apply button if you see the screen working normally after clicking Test Ifthe screen is not normal change to a different mode lower mode of resolution colors or frequency Note If there is no Mode at All Display Modes select the level of resolution and vertical frequency by referring to the Preset Display Modes in the user guide Linux Operat
35. n drivers for this device so that can choose a specific driver then click Next and then click Have disk Click the Browse button then choose A D Driver Click the Open button then click OK button Choose your monitor model and click the Next button then click Next button Click the Finish button then the Close button If you can see the Digital Signature Not Found window then click the Yes button And click the Finish button then the Close button SAMSUNG DIGITal everyone s invitedm Setup 4 Microsoft Windows Millennium Operating System DO ASS ef _ Click Start Setting Control Panel Double click Display icon Select the Settings tab and click Advanced Properties button Select the Monitor tab Click the Change button in the Monitor Type area Choose Specify the location of the driver Choose Display a list of all the driver in a specific location then click Next button Click the Have Disk button Specify A D driver then click OK button Select Show all devices and choose the monitor that corresponds to the one you connected to your computer and click OK Continue choosing Close button and OK button until you close the Display Properties dialogue box You can get some other screen for warning message or others then click the appreciate option for your monitor a Microsoft Windows 98 Operating System D
36. nal differs the screen may go blank while the power LED is on Refer to the video card manual and adjust the screen as follows Display Mode Horizontal Frequency Vertical Frequency Pixel Clock sync Polarity Horizontal Frequency The time to scan one line connecting the right edge to the left edge of the screen horizontally is called Horizontal Cycle and the inverse number of the Horizontal Cycle is called Horizontal Frequency Unit KHz Vertical Frequency Like a fluorescent lamp the screen has to repeat the same image many times per second to display an image to the user The frequency of this repetition is called Vertical Frequency or Refresh Rate Unit Hz DD a q SAMSUNG DIGITal everyone s invitedm User s Manual 45 Specifications PowerSaver This monitor has a built in power management system called PowerSaver This system saves energy by switching your monitor into a low power mode when it has not been used for a certain amount of time The monitor automatically returns to normal operation when you move the computer s mouse or press a key on the keyboard For energy conservation turn your monitor OFF when it is not needed or when leaving it unattended for long periods The PowerSaver system operates with a VESA DPMS compliant video card installed in your computer Use a software utility installed on your computer to set up this feature Normal Operation Poweer off mode EPA ENERGY 2000
37. ndor a wizard This Chives Prowicd N han vd eig pou nat ee bor Chirres Date Ao Pius dre Plage Moraer Duram Wes pene 6 1 00 0 e keked Sipru WA kerak ad Windia LS adhahar a If pow hasdesen come wilh an metalstion LO w lloppp disk iment ii now Fo wine ajah ai ala ehren flow wa i 2 5 To ignia thee vea Buja lhis dayon la al Kap Az i Ei al the rare automatically Farnar i 1 lies aboa a after apte ne drives ro ay f 7 Beach Dre back ber ins previous miele Cm natal bom a KA of pecie locaton Kadar Liramakadl Fours den are Behr ich Newt io continue CE Cote ter ce 6 Select Don t search I will then click Next and then click Have disk Hardware Update Wizard Hardware Update Wizard Pisaro choco pma coach and inzlallation opkimne ae Teken the deine dive pou wani ia install Tas this hard Search ia the beat driver in these locair i Sobel the re are Free off our hache dee ane then chek Meet you a hyss a ak that conne dus dene ara an lo retail ook Have Dink RE RER E En qui gear whech ne local path aed Bere meets Thee bert drei lond wall be wai akeni e Free gompantis Ferara Mosd SR Pag and Pap Hontai Eon mearch val choose the driver ta rata Choose thia option bo select the devane drea homa B Windows does mot quavantes thak des et poss choco veal bee thes bert match for pour harama SS That chee in gay signed Lese me 7 Click the Browse butt
38. net web site shown here e Internet web site http www samsung monitor com Europe http www samsungmonitor com USA http www sec co kr Korea http www samsungmonitor com cn China Windows ME 98 95 1 Insert CD into the CD ROM driver 2 Click Windows ME 98 95 Driver Windows MERS Driver Windows KRONO Driver ram SAMBUNG Eu 3 Choose your monitor model in the model list then click the OK button Samsung Monitor Setup for Windows MEETS Pick the display adapter which you want to install the monitor 53 Inc Savage Pick the monitor which you want to install SyncMaster F03DF ey S4DFx SyncMaster 630 FLN TOIOF EF aIOF ES Magichynchaster SyncMaster fS5DF 4 zu 4 Click the Install button in the Warning window Warning Select the monitor name that exactly m tches the name printed on the front of your monitor or on the back label If you select the wrong monitor restart Windows in the Safe Mode and use this CD ROM again to select the correct monitor SAMSUNG DIGITal everyone s invitedm Setup Windows XP 2000 1 Insert CD into the CD ROM driver 2 Click Windows XP 2000 Driver Windows MENASI Driver Windows KRING Driya Fi SARSUME CREED 3 Choose your monitor model in the model list then click the OK button Su Hontlor Setup Por Verde SI Pick thee cinplay harter om eich yo re te rrela tha tor NTT CaP cerca KA Pee So Car
39. nterlace Methods Showing the horizontal lines of the screen from the top to the bottom in order is called the Non Interlace method while showing odd lines and then even lines in turn is called the Interlace method The Non Interlace method is used for the majority of monitors to ensure a clear image The Interlace method is the same as that used in TVs 6 Plug amp Play This is a function that provides the best quality screen for the user by allowing the computer and the monitor to exchange information automatically This monitor follows the international standard VESA DDC for the Plug amp Play function 6 Resolution The number of horizontal and vertical dots used to compose the screen image is called resolution This number shows the accuracy of the display High resolution is good for performing multiple tasks as more image information can be shown on the screen Example If the resolution is 1024 X 768 this means the screen is composed of 1024 horizontal dots horizontal resolution and 768 vertical lines vertical resolution SAMSUNG DIGITal everyone s invitedm User s Manual 48 Information Regulatory FCC Information IC Compliance Notice MPR II Compliance European Notice Europe only PCT Notice TCO 95 Ecological requirements for personal computers TCO applied model only TCO 99 Ecological requirements for personal computers TCO applied model only FCC Information User Instructions The Federal Comm
40. on then choose A D Driver and choose your monitor model in the model list and click the Next button Install From Disk A Insert tha manulschune s installation dik ard ther i 3 Die rer aed madal of pout are rn re cle Alec D po make sure that the correct drive ts selected below 4 Fun ih dik that Cain the ver yeu meurt bo rt bc Have Da Model pnois 1 154 17567 UMTS Ma barak salar CH 735 Copy manulschuer s fies bom By Tin driwer ie rot digitally signed Tel te web dre marina ji roland 8 If you can see following Message window then click the Continue Anyway button Then click OK button Hardware Installation The software you are installing for this hen ceeane Synch ache 171517557 1705 Mages ypnchlaster 41753 has na puted indes Lage being to wany is Gompahkahly wath inos P Tell ree weh thee testing is ngabari Continuing your installation of this software map impir or destabilize the corect oper contact the hardware vendor for software that has passed Windows Loge testing SAMSUNG DIGITal everyone s invitedm Setup 9 This monitor driver is under certifying MS logo and this installation don t damage your system The certified driver will be posted on Samsung Monitor Homepage http www samsung monitor com Click the Close button then click OK button continually Hardware Update Wizard Completing the Hardware Update Wizard Tike vase Kart Frocthosclicttalng the setter ki
41. rallel blades plug cap For 240 Volt applications use only UL Listed Detachable power supply cord with NEMA configuration 6 15P type tandem blades plug cap 6 IC Compliance Notice This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations of ICES 003 Cet appareil Num rique de classe B respecte toutes les exigences du Reglemont ICES 003 sur les quipements produisant des interferences au Canada 6 MPR II Compliance This monitor complies with SWEDAC MPR recommendations for reduced electric and magnetic fields 6 European Notice Europe only Products with the CE Marking comply with both the EMC Directive 89 336 EEC 92 31 EEC 93 68 EEC and the Low Voltage Directive 73 23 EEC issued by the Commission of the European Community Compliance with these directives implies conformity to the following European Norms e EN55022 1998 Radio Frequency Interference e EN55024 1998 Electromagnetic Immunity e EN61000 3 2 1995 A1 A2 Power Line Harmonics e EN61000 3 3 1995 Voltage Fluctuations e EN60950 Product Safety PCT Notice SAMSUNG DIGITal everyone s invitedw User s Manual 50 Information 6 TCO 95 Ecological requirements for personal computers TCO applied model only AB general requirements AB2 Written Eco document acompanying the products Congratulations You have just purchased a TCO 95 approved and labelled product Your choice has provided
42. rea U Previous Menu SAMSUNG DIGITal everyone s invitedm User s Manual 33 On Screen Display OSD Menu System Menu How to adjust The Degauss feature will remove color impurities caused by magnetic fields You can use this function to turn on the power of the monitor or change the power saving mode to the normal mode Do not use the Degauss feature more than once within a 30 minute period lt D D J With the menu off push the menu button amp D E 3 D Exit Menu 2 Push the button or button until the Degauss screen is displayed 3 Push the menu button to execute the degauss function The degaussing screen will appear U Exit Menu Note The monitor may buzz momentarily the image colors may change and the image will jiggle for a few seconds These effects are normal Use the recall feature to reset these monitor settings to their original levels Position Size Pincushion Trapezoid Parallelogram Pinbalance Rotation H Moire and V Moire J With the menu off push the menu button WU Exit M i D Exit Menu Push the button or button until the Recall Ze 2 screen is displayed 4 0 0 CI 3 Push the menu button to open the Recall adjustment screen 4 Push the button to select Yes If you don t want to reset the monitor use the button to select No U Previous Menu Note If you have selected Yes all settings listed above will be r
43. s Menu Use the button or button to select the language you would like to use 3 Push the menu button to open the Language selection screen 4 Note The language chosen affects only the language of the OSD It has no effect on any software running on the computer SAMSUNG DIGITal everyone s invitedm User s Manual 30 On Screen Display OSD Menu System Menu How to adjust V Moire A Moire pattern can appear on your screen looking like a series of concentric circles or arcs To eliminate this pattern use the clear moire adjustments J With the menu off push the menu e button U Exit Menu lt 90 COO B CVA MERS 2 Push the button or button until the Advanced screen is displayed 3 Push the menu button again and then press the or button until the V Moire screen appears Push the menu button to open the V Moire adjustment screen ID Previous Menu Use the button or button to adjust vertical moir 7 Previous Menu SAMSUNG DIGITal everyone s invitedm User s Manual 31 On Screen Display OSD Menu System Menu How to adjust Video Input Level Some video cards use video signals higher than 1 0V which causes the display to be very bright For those video cards use this feature to select the 1 0V Level J With the menu off push the menu button 99D Exit Menu 2 Push the button or button until the Advanced lt o 90 screen is displayed
44. s of electricity generation have a negative effect on the environment e g acidic and climate influencing emissions radioactive waste it is vital to save energy Electronics equipment in offices is often left running continuously and thereby consumes a lot of energy What does labelling involve The environmental demands has been developed by Svenska Naturskyddsforeningen The Swedish Society for Nature Conservation These demands impose restrictions on the presence and use of heavy metals brominated and chlorinated flame retardants CFCs freons and chlorinated solvents among other things The product must be prepared for recycling and the manufacturer is obliged to have an environmental policy which must be adhered to in each country where the company implements its operational policy The energy requirements include a demand that the computer and or display after a certain period of inactivity shall reduce its power consumption to a lower level in one or more stages The length of time to reactivate the computer shall be reasonable for the user Below you will find a brief summary of the environmental requirements met by this product The complete environmental criteria document may be ordered from TCO Development SE 114 94 Stockholm Sweden Fax 46 8 782 92 07 Email Internet develooment tco se Current information regarding TCO 99 approved and labelled products may also be obtained via the Internet using the address http www
45. st screen image position and suddenly has the driver size using the OSD become unbalanced Have you adjusted the resolution or Adjust the resolution and frequency er at the video card frequency to the monitor Refer to the Preset Display Modes The screen can be unbalanced due to the cycle of the video card signals Readjust Position by referring to the OSD Have you adjusted the resolution or frequency on the monitor The screen is out of focus or OSD cannot be adjusted e Adjust the resolution and frequency of the video card Refer to the Preset Display Modes SAMSUNG DIGITal everyone s invitedm Troubleshooting Symptom The screen is partially distorted LED is blinking but no images on the screen There are only 16 colors shown on the screen The screen colors have changed after changing the video card There is a message that reads Unrecognized monitor Plug amp Play VESA DDC monitor found Chek List Are there any magnetic products such as an adapter speaker or a high voltage wire near the monitor Is the frequency properly adjusted when checking the Display Timing on the menu Have the Windows colors been set properly Has the video card been set properly Have you installed the monitor driver See the video card manual to see if the Plug amp Play VESA DDC function can be supported 3 User s Manual Solution e Enter the OS
46. t by the TCO The Swedish Confederation of Professional Employees Naturskyddsforeningen The Swedish Society for Nature Conservation and NUTEK The National Board for Industrial and Technical Development in Sweden The requirements cover a wide range of issues environment ergonomics usability emission of electrical and magnetic fields energy consumption and electrical and fire safety The environmental demands concern among other things restrictions on the presence and use of heavy metals brominated and chlorinated flame retardants CFCs freons and chlorinated solvents The product must be prepared for recycling and the manufacturer is obliged to have an environmental plan which must be adhered to in each country where the company conducts its operations policy The energy requirements include a demand that the monitor after a certain period of inactivity shall reduce its power consumption to a lower level in one or more stages The length of time to reactivate the monitor shall be reasonable for the user Labelled products must meet strict environmental demands for example in respect of the reduction of electric and magnetic fields along with physical and visual ergonomics and good usability TCO Development Unit 1996 11 29 On the page this folder you will find a brief summary of the environmental requirements met by this product The complere environmental criteria document may be ordered from TCO Development Unit S 11494 Stockho
47. tco info com Environmental requirements Flame retardants Flame retardants are present in printed circuit boards cables wires casings and housings Their purpose is to prevent or at least to delay the spread of fire Up to 30 of the plastic in a computer casing can consist of flame retardant substances Most flame retardants contain bromine or chloride and those flame retardants are chemically related to another group of environmental toxins PCBs Both the flame retardants containing bromine or chloride and the PCBs are suspected of giving rise to severe health effects including reproductive damage in fish eating birds and mammals due to the bio accumulative processes Flame retardants have been found in human blood and researchers fear that disturbances in foetus development may occur The relevant TCO 99 demand requires that plastic components weighing more than 25 grams must not contain flame retardants with organically bound bromine or chlorine Flame retardants are allowed in the printed circuit boards since no substitutes are available Cadmium Cadmium is present in rechargeable batteries and in the colour generating layers of certain computer displays Cadmium damages the nervous system and is toxic in high doses The relevant TCO 99 requirement states that batteries the colour generating layers of display screens and the electrical or electronics components must not contain any cadmium Mercury Mercury is sometimes found in b
48. te irr aed re ia Waster 17157 17557 1705 Magicovechaster CE Pick them Mac TONT which you want Tas install SRH 1511 1551 LANG Aero IS LE ai lue Swrchaster 151 T1557 1507 MBOK SATIA Katan CLS LEONE S rchiaster DSL I FO Met ee Ce Loo S rcMarter Feat Sree Mani FA ister Or Ls Li m ia 17 HAR ip kk E Dunchlsster TITI Er TOT Kisgkfiyrefdacher Z SIE Ca EM LOT Mack tyre am CHI FIDEL Masten hee CL TE rec lire LiDE 10107 den 1000 PA daja Tg E TEKA b Sur cHaster 1Gi7 i057 LOOT Magik SyncMaster Cx LEE arn SyrcHzter 1817 LOST LOT Mack oyicMaeter Cx LSS Col Greene oh TS PoP ito Sanur Seiad LATE na Be ee bad Cu ox 4 Click the Install button in the Warning window Warning Select the monitor name that exactly matches the name printed on the front of your monitor or on the back label If you select the wrong monitor restart Windows in the Safe Mode and use this CD ROM or Diskette again to select the correct monitor Cancel 5 If you can see following Message window then click the Continue Anyway button Then click OK button Hardware Installation AN The software you are installing for this hademe Synch saben 17154 17554 1705 Magie ynchlaster CH 765 has rai pasta hiret Loge bating lo venly li compat ah einher SP sell ine ehe Eu bare ii Wr Lonlimurg your insballal orn of the software map impair ce destiabal re tv an ern pour Eli ter immediately or in the
49. tor LED is still on The message may indicate that the monitor is out of scan range or that you need to check the signal cable Environment The location and the position of the monitor may influence the quality and other features of the monitor 1 If there are any woofer speakers near the monitor unplug and relocate the woofer to another room 2 Remove all electronic devices such as radios fans clocks and telephones that are within 3 feet one meter of the monitor 3 Degauss the monitor if any devices were removed from the area Userful Tip A monitor recreates visual signals received from the PC Therefore if there is trouble with the PC or the video card this can cause the monitor to become blank have poor coloring noise Sync Out of Range etc In this case first check the source of the problem and then contact a service center or your dealer Judging the monitor s working condition lf there is no image on the screen or an Sync Out of Range message comes up disconnect the cable from the computer while the monitor is still powered on f there is a message coming up on the screen or if the screen goes white this means the monitor is in working condition In this case check the computer for trouble SAMSUNG DIGITal everyone s invitedm User s Manual 4 Specifications General Specifications General Model Name SyncMaster 551v Picture Tube Type 15 38cm Full square type 35cm view
50. unications Commission Radio Frequency Interference Statement includes the following warning Note This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television receptions which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help User Information Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment If necessary consult your dealer or an experienced radio television technician for additional suggestions You may find the booklet calle
51. ust Follow these instructions to change the Size of the monitor s entire display J With the menu off push the menu button D Exit Menu Push the button or button until the H Size screen is displayed 2 F Push the menu lt button to open the H Size adjustment screen 006 3 p QO IRS 4 Use the and buttons to change the Horizontal Size of the monitor s viewing area 49D Previous Menu Follow these instructions to change the Size of the monitor s entire display J With the menu off push the menu button D Exit Menu Push the button or button until the V Size screen is displayed 420 LT 2 Push the menu button to open the V Size adjustment screen DIE a Use the and buttons to change the Vertical Size of the monitor s viewing area I Previous Menu SAMSUNG DIGITal everyone s invitedm Users Manual 26 On Screen Display OSD Menu System Menu ID Exit Menu co 9 D DO 2 PP TI gt Previous Menu U Exit Menu or 0 COO G aao g D Previous Menu lt oa D 2 wo ago g WU Previous Menu How to adjust Adjust the pincushion setting when the sides of the display are bowed in or bowed out With the menu off push the menu button Push the button or button until the Pincushion screen is displayed Push the menu button to open the Pincushion adjustment screen Use the button or
52. you with a product developed for professional use Your purchase has also contributed to reducing the burden on the environment and to the further development of environmentally adapted electronic products Why do we have environmentally labelled monitors In many countries environmental labelling has become an established method for encouraging the adaptation of goods and services to the environment The main problem as far as monitors and other electronic equipment are concerned is that environmentally harmful substances are used both in the products and during their manufacture Since it has not been possible so far for the majority of electronic equipment to be recycled in a satisfactory way most of these potentially damaging substances sooner or later enter Nature There are also other characteristics of a monitor such as energy consumption levels that are important from both the working and natural environment viewpoints Since all types of conventional electricity generation have a negative effect on the environment acidic and climate influencing emissions radioactive waste etc it is vital to conserve energy Electronic equipment in offices consumes an enormous amount of energy since it is often routinely left running continuously What does labelling involve This product meets the requirements for the TCO 95 scheme which provides for international environmental labelling of monitors The labelling scheme was developed as a joint effor
53. yourself If you do need assistance please call the phone number on the warranty card the phone number on the Information section or contact your dealer Symptom No images on the screen cannot turn on the monitor cannot see the On Screen Display Chek List Is the power cord connected properly Can you see No Connection Check Signal Cable on the screen lf the power is on reboot the computer to see the initial screen the login screen which can be seen Can you see Sync Out of Range on the screen There is no image on the screen s the power indicator on the monitor blinking at 1 second intervals Have you locked the On Screen Display OSD Menu to prevent changes Solution Check the power cord connection and supply Check the signal cable connection e f the initial screen the login screen appears boot the computer in the applicable mode the safe mode for Windows 98 95 and then change the frequency of the video card Refer to the Preset Display Modes e Note If the initial screen the login screen does not appear contact a service center or your dealer You can see this message when the signal from the video card exceeds the maximum resolution and frequency that the monitor can properly handle e Adjust the maximum resolution and frequency applicable to the monitor e The monitor is in PowerSave mode Press a key on the keyboard or move the mouse to activat
54. ys Cadmium damages the nervous system and is toxic in high doses 6 TCO 95 requirement states that batteries may not contain more than 25 ppm parts per million of cadmium The colour generating layers of display screens must not contain any cadmium Mercury Mercury is sometimes found in batteries relays and switches Mercury damages the nervous system and is toxic in high doses 6 1CO 95 requirement states that batteries may not contain more than 25 ppm parts per million of mercury It also demands that no mercury is present in any of the electrical or electronics components concerned with the display unit CFCs freons CFCs freons are sometimes used for washing printed circuit boards and in the manufacturing of expanded foam for packaging CFCs break down ozone and thereby damage the ozone layer in the stratosphere causing increased reception on Earth of ultraviolet light with consequent increased risks of skin cancer malignant melanoma 6 The relevant TCO 95 requirement Neither CFCs nor HCFCs may be used during the manufacturing of the product or its packaging 6 TCO 99 Ecological requirements for personal computers TCO applied model only Congratulations You have just purchased a TCO 99 approved and labelled product Your choice has provided you with a product developed for professional use Your purchase has also contributed to reducing the burden on the environment and also to the further development of environmentally a

Samsung 512N Computer Monitor User Manual

Contents

Download Pdf Manuals

Related Search

Related Contents