Roper Dishwasher Dishwasher User Manual
Contents
1. Installation Instructions w OO a ROPER O Undercounter IMPORTANT Dishwasher Installer Leave Installation Instructions with the appliance Save Installation Instructions for local electrical inspector s use Before you start Proper installation is your responsibility Make sure you have everything necessary for correct installation It is the responsibility of the customer to Proper electrical drain and water supply lines must be available or must be installed as specified within shaded area See Electrical requirements Water requirements and Drain requirements sections Plumbing and wiring shouid not cross in Check location where dishwasher will be installed The location should provide e Easy access to water electricity and drainage lines e Convenient loading the best position is left or right of kitchen sink Square opening for proper dishwasher operation contact a qualified installer to assure front of the motor or the dishwasher that the plumbing and electrical legs installations are adequate and meet national and local codes and ordinances IMPORTANT Observe all governing codes and ordinances Corner location 2 min door to cabinets orwall Take care not to damage power cord during installation or removal of dishwasher Electrical ground is required See Electrical Grommet eee requirements required A section electrical F2. Numbers correspond to steps 5 The dishwasher is shipped to E be installed in 34 cabinet opening Measure height of cabinet opening from underside of countertop to floor Check chart for that height opening Put the wheels in the required position and turn front levelers the number of times indicated WHEEL NUMBER MIN POSITION OF TURNS CUTOUT See TO PREADJUST HEIGHT Utustration LEVELERS 34 3414 2 3496 4 347 S CAUTION Fioor Damage Tilt dishwasher backwards on wheels when moving across floor Failure to do so may cause damage to floor covering Untape drain hose Close and latch dishwasher door Push dishwasher into place sliding drain hose and power cord if available through holes cut in cabinet wall Align dishwasher door with cabinet front not doors so that spacing is the same on both sides and top to bottom Center dishwasher in cabinet opening Check that front leveling legs are firmly against the floor _A some UU i 10 AV co TEn a b a ce ut hose connector to fit To connect drain hose to an air gap or waste tee cut end of drain hose as shown Do Not cut drain hose when connecting to a disposer Knock out plug from disposer inlet Secure drain hose with hose clamp provided Do Not cut ribbed section to shorten drain hose Coil and tape extra drain hose under kitchen sink ACAUTION Product Damage Do N
3. with a length of No 4 wire securely clamped to bare melal at both ends Temporary grounding method g Grounding assembly attached ar O grounded metal cold water pipe with paint removed Cover plate grounding clamp must be tight on pipe Screw 2 prong a prong type wall grounding Grounding prong receptacle plug Power supply cord Figure 6 If changing and properly grounding the electrical supply is impossible and where local codes permit consult your electrical inspector a temporary adapter may be plugged into the 2 prong wall receptacle to mate with the 3 prong power supply cord See Figure 6 If this is done you must connect a separate copper grounding wire from the external grounding connector screw inside the terminal box to the grounded cold water pipe See Figure 5 Do Not connect to electrical supply until appliance is permanently grounded Do Not ground to a gas supply pipe or hot water pipe If power cord cannot be used When local codes do not permit use of a power cord with an undercounter dishwasher the power cord must be removed and dishwasher wired directly IF THE POWER SUPPLY CORD IS REMOVED THE DISHWASHER MUST BE CONNECTED WITH COPPER WIRE ONLY appliance power supply cable strain T relief Y grounding connector screw Figure 7 4 Disconnect the power supply 2 Remove terminal box cover 3 Remove wire connectors from the po
4. at fasten dishwasher to countertop and shift tub Tighten screws less tension oor spri adjustment notches 0 more tension dishwasher leg 13 Check door for proper operation Door should close easily without slamming and open with its own weight If necessary Close door and adjust door spring with pliers 14 Toke a few minutes to read the Use and Care Guide to fully understand your new dishwasher 15 Check that all parts have been installed and no steps were skipped Check that you have all the tools you started with 16 Turn on electric supply Start dishwasher and allow it to complete a cycle Check that dishwasher is working properly and that there are no water leaks Replace the access panel You have Just finished Installing your new Roper Undercounter Dishwasher Congratulations Keep Installation Instructions avaliable for easy reference To Change Door And Access Panel Color For models so equipped ACAUTION Personal Injury Hazard Handle metal edges of panels carefully Cu metal edges may cause personal Injury or damage to other materials Remove two screws securing one of the side trim pieces Slide trim downward until upper edge is free of console or end cap Lift off trim piece 2 Slide out color panel s and corrugated spacer Select panel color you wish fo have showing and piace on top of panels Slide color panel s and spacer into the l
5. e Figure 3 4 Connect the green grounding wire of the power supply cable to the grounding connection screw located inside the terminal box See Figure 3 5 Replace terminal box cover Alternate grounding method If the recommended grounding method is impossible connect a separate green grounding wire No 16 minimum from grounding connection screw located inside the terminal box to a grounded copper cold water pipe See Figure 5 THIS HOWEVER IS NOT RECOMMENDED Do Not connect to electrical supply until dishwasher is permanently grounded Do Not ground to a gas supply pipe or hot water pipe Grounded cold water pipe must have metal continuity to electrical ground and nol be interrupted by plastic rubber or other insulating connectors such as hoses fittings washers or gaskets including waler meter or pump Any insulating electrical connector should be jumped with a length of No 4 copper wire securely clamped to bare metal at bolh ends See Figure 5 B Power supply cord method connecting dishwasher to outlet Local codes may permit the use of a UL listed flexible three conductor power supply cord terminated with a three prong grounding type plug It is recommended that cord kit Part No 675456 available from your Roper dealer or parts supplier be used If the cord kit is not available locally the flexible cord used must be a UL listed three conductor 16 gauge cord that mee
6. er to prevent personal Injury from exposed wiring Failure to do so could result In fire electrical shock or other personal Injury from exposed wiring ACAUTION Personal Injury Product Damage Avold opening dishwasher door before dishwasher Is installed Dishwasher may tip over when door is opened resulting in personal injury or product Tools needed for installation p S BS sie and 4 pipe wrench socket wrench keyhole saw measuring tape electric drill level Phillips screwdriver pliers 2 adjustable wrenches tubing cutter flat blade screwdriver not shown wire stripper or knife pipe joint compound 2 Run flexible armored or non metallic sheathed copper cable with grounding wire from the fused disconnect circuit breaker or junction box through the or larger cabinet hole to the dishwasher location The cable must extend 24 from the back wall The hole cut through a wood cabinet should be sanded until smooth The hole cut through a metal cabinet must be covered with a grommet Part No 302797 A ULL listed strain relief must be installed at each end of the power supply cable at the dishwasher and at the junction box Wire sizes COPPER WIRE ONLY must conform with the rating of the dishwasher 3 Remove the dishwasher terminal box cover Connect the white and black wires of the power supply cable to the white and black leads in the terminal box with twist on wire connector Se
7. her materials 4 Remove corrugated E spacer and all color panels and save for future use 5 Install custom panel and one E color panel color panel must be used as described in Steps 3 and 4 To change access and front panel color 6 Repeat Steps 1 and m 2 of this section for cutting custom panels for the access panel Use specified dimensions shown 7 Remove top trim E piece from access panel as described in Step 5 To change door and access panel color 8 Remove corrugated E spacer and all color panels and save for future use 9 Install custom panel and one E color panel color panel must be used as described in Steps 6 and 7 To change door and access panel color IF THE DISHWASHER IS NOT OPERATING PROPERLY Check these points e Is the door closed tightly and latched securely e Has the cycle been set correctly to start the dishwasher e Is the water turned on e Has a house fuse blown e Has electrical power been interrupted Note If the motor has stopped because of overload if will automatically reset itself within a few minutes If after checking these points the dishwasher still does not run or complete a cycle call for service ROPER eS aay art No 3369941 31989 Whirlpool Corporation Prepared by Whirlpool Corporation Benton Harbor Michigan 49022 Printed in US A
8. ng grounding type receptacle grounded in accordance with the National Electrical Code ANSI NFPA 70 latest edition and all local codes and ordinances If a mating wall receptacle is not available it is the personal responsibility and obligation of the customer to have a properly grounded 3 prong wall receptacle installed by a qualified electrician See Figure 4 3 prong grounding type wall receptacle 3 prong grounding plug power supply cord Figure 4 1 Have a 3 prong grounding type wall receptacle available or installed by a qualified electrician on the rear wall of one cabinet next to dishwasher opening See Figure 1 Panel A grounded cold waler pipe No 4 wire a _ grounding wire green grounding Py connecior screw Figure 5 2 For added personal safety use clamp and green colored copper grounding wire Connect the grounding wire 16 minimum from the external grounding connector screw inside the terminal box toa grounded cold water pipe See Figure 5 Do Not connect to electrical supply until appliance is permanently grounded Do Not ground to a gas supply pipe or hot water pipe Grounded cold waler pipe must have melal continuity to elecirical ground and not be interrupted by plastic rubber or other electrical insulating connectors such as hoses filings washer or gaskets including water meter or pump Any electrical insulating connector should be jumped as shown
9. or flush hole The unshaded mount depth metal cabinet area must be Den wall receptacle must be at within 36 max free of pipes leas 2442 Do Not install mom right or eee V hole or larger ii i hela i It 8 a rgor ne g dishwasher OVET wuna max drain line 172 hole or larger ee Re carpeted flooring opening electrical line Y hole or larger 77 AN wa cor ers Fe x No min underside counter helght 452 i XR Ir Ninig valve 6 lt 2 leg 24 openin clearance OPAN 9 Read and follow the Electrical requirements Water requirements and Drain requirements connection section before installing the dishwasher Figure 1 Side view Back view electrical Junction box electrical water Junction box Inlet valve Electrical requirements A 120 volt 60 Hz AC only 45 or 20 ampere fused electrical supply is required Time delay fuse or circuit breaker is recommended It is recommended that a separate circuit serving only this appliance be provided AWARNING Electrical Shock Hazard e Electrical ground Is required on this appliance e Check with a qualified electrician If you are In doubt as to whether the appliance Is propery grounded Improper connection of the equipment grounding conductor can result in fire electrical shock or other personal Injury e Disconnect the power supply at the Junction box e Do Not connect appliance to electrical sup
10. ot solder within 6 of piastic water Inlet valve Failure to follow this instructlon could result in product damage a water Iniet valve 8 Connect water pipe or tubing directly to water inlet valve Do Not run pipe or tubing across front of motor or dish washer legs Pierce a 2 diameter hole through the sound shield sound shield is not available on all models for water line See Figure 8 Panel B Turn on water supply and check for leaks PANEL D TF gi itn Make electrical connection or plug power supply cord into the grounded outlet Check electrical requirements Be sure you have correct electrical supply and recommended grounding method top mouniing Phillips head screws No 10 x 2 i i Oo Do Not drop screws into tub Remove all shipping materials Open dishwasher door remove bottom rack Place a newspaper or large sheet of paper over bottom of dishwasher to protect the pump area when securing dishwasher to countertop 11 Secure dishwasher to countertop with two No 10 x 2 Phillips head screws from parts bag You MUST secure dishwasher to keep it from tilting when door is opened or closed Do Not drop screws in dishwasher tub If screws should fall into the pump pump and motor failure may occur Remove paper from bottom of dishwasher Open door approximately 3 and check for equal spacing between inner door and tub sides If necessary loosen screws th
11. ower door trim and the groove on underside of console Gently push on panel surface to fit panel under side trim edge PANEL E Slide the side trim piece against the console or end cap Align side trim and mounting holes in door frame Secure trim to door with screws upper access panel screws 5 Loosen the upper access panel screws and pull access panel outward Remove and save three screws securing the top trim Remove top trim X Pull out desired color panel and place in front of other panels and corrugated spacer with desired color facing out 7 Replace top trim with three screws Move access panel back into position and tighten upper access panel screws Installing Customized Wood Door Panels Dishwasher door panel and access panel can be customized to match wood cabinets L e 23h aeaa F Door panel 4 Cut panels using E specified dimensions 23 6 x 190 x Ya Make sure wood grain matches direction of cabinet wood grain 2 Rout all four sides E of both panels 1 x deep to provide room for installation clearance Dishwasher Is subject fo some humidity Cover both sides and edges of wood panels with moisture resistant sealer 3 Remove side trim E piece as described in Step 1 To change access and door panel color ACAUTION Personal Injury Hazard Handle metal edges of panels carefully Cut metal edges may cause persona Injury of damage to ot
12. ply until appliance Is permanently grounded Do Not use an extension cord with this appliance s This appliance must be connected to a grounded metallic permanent wiring system or a grounding conductor should be connected to the grounding terminal or wire lead on the appllance e Do Not use a fuse in the neutral Fallure to follow these Instructions could result In a fire electrical shock or other personal Injury It is the personal responsibility and obligation of the customer to contact a qualified electrician to assure the electrical installation is adequate and in conformance with the National Electrical Code ANSI NFPA 70 latest edition and local codes and ordinances The dishwasher must be connected with copper wire only Wiring methods Pick one method to follow depending upon your dishwasher and local codes A Direct wire method cable connecting dishwasher to ajunction box Recommended grounding method 1 Disconnect the power supply PANEL A and appearance Cabinet front that is perpendicular to floor e Protection so that water intet valve and drain cannot freeze e 7 minimum clearance between motor and flooring to prevent motor overheating AWARNING Electrical Shock Hazard Electrical wiring and components must Not contact any plumbing material or drain hose Cabinet opening must completely enclose sides top and back of dishwash
13. re 13 Most disposers have 7 connectors or special connectors are available at plumbing supply houses Be sure to remove the disposer plug before connecting the draln hose All parts are available through your Roper dealer PANEL C Insertin Dishwasher in Opening 4 Shut off water line valve Check B that electric supply is off 2 If color of door and access E panel are to be changed or custom panels installed change the panels now See Panel E for detailed instructions ACAUTION Personal Injury Product Damage Avoid opening dishwasher door before dishwasher is installed Dishwasher may tip over when the door is opened resulting in personal injury of product 3 The carton and skid should have been removed from the dishwasher as described in the instructions on the canton If you have removed the carton without removing the skid from the dishwasher a Place two foam shipping pieces behind dishwasher Firmly grasp the body of the dishwasher and gently lay it on its back on the foam shipping pieces D Use a socket wrench or screwdriver to remove the screws holding the skid to the bottom of the dishwasher c Stand dishwasher upright Loosen 4 screws Do Not remove I LLLMeRIEEE PD rece as yA pe i eS QS 4 Loosen do not remove the 4 screws attaching access panel to dishwasher using a socket wrench or Phillips screwdriver Remove access panel and set aside
14. ts the National Electrical Code ANSI NFPA 70 latest edition and all local codes and ordinances The length of the cord must not exceed six feet It must be routed so that it does not touch the dishwasher motor or the lower portion of the dishwasher tub A grommet Part No 302797 must cover the hole cut In a metal cabinet for the flexible cord The flexible cord must be plugged Into a mating three prong grounding type wall receptacle grounded in accordance with the National Electrical Code ANSI NFPA 70 latest edition and all local codes and ordinances Follow instructions packaged with the flexible cord Recommended grounding method AWARNING Electrical Shock Hazard e Electrical ground Is required on this appliance e Improper connection of the equipment grounding conductor can result in a risk of electrical shock e Check with a qualified electrician you are In doubt as to whether the appliance Is properly grounded Do Not modify or remove the power supply cord plug Hf plug does not fit the outlet have a proper outlet Installed by a qualified electrician Do Not use an extension cord with this appliance e Do Not have a fuse In the neutral Failure to follow these Instructions could result in a fire electrical shock or other personal injury PANEL B Dishwashers equipped with a power supply cord have a 3 prong grounding plug The power supply cord must be plugged into a mating 3 pro
15. wail for drain hose Additional drain line a minimum of D and no longer than 20 feet can be used if needed Pick one method Recommended rubber connector Part No 674384 Cut hose connecior to fit clearance FI totoot Entry must be gure 10 t above trap install air gap Part No 300096 according to kit instructions in the drain line before line connects to household plumbing if other brands of air gaps are used they should be checked to make sure they allow for the same water flow Connect the air gap to a waste tes Part No 675149 or disposer using a rubber connector Part No 674381 Most disposers have 7 connectors or special connectors are available ot plumbing supply houses Be sure fo remove the disposer plug before connecting the drain hose Cut hose connector rubber connector 3 to fit Part No 674381 Remove disposer 20 min clearance to floor Entry must be above trap Figure 11 Cut hose connector to fit Alternate methods If local plumbing codes permit the dishwasher may 20 min be connected to clearance the drain through a waste tee Part No 675149 or directly to a waste disposer Figure 12 Entry must be above trap The waste tee connection MUST be made ahead of the trap and a minimum of 20 inches above the floor connector Remove disposer Inlet plug 20 min cleatance to floor Figu
16. wer cord wires and grounding wire screw See Figure 7 4 Disconnect the strain relief behind the terminal box from the dishwasher leg 5 Remove power cord and strain relief from terminal box hole 6 See A Direct wire method Panel A for further instructions Water requirements A LES cabinei wall P d sound shield y4 pipe thread Figure 8 The hot water line to the dishwasher must provide between 15 120 PSI water pressure The hot water heater should be set to deliver 140 F water temperature to the dishwasher for best results Use Ya O D copper tubing or 2 plastic tubing minimum inlet line Dishwasher intet valve has internal pipe thread 4 Rough In water line before installing dishwasher using one of the routing methods shown In Figure 8 Cut a Y or larger hole In cabinet rear wall or floor for pipe 2 Install a shutoff valve in the water line where it can be easy to access 3 Flush water line into a bucket fo get rid of any particles that may clog inlet valve Drain requirements Some models are not equipped with a drain hose A drain hose that meets AHAM DW test standards must be securely clamped to the pump s drain outlet Drain hoses are available through your Roper dealer Drain hose when supplled meets AHAM DW test standards Drain line connection to house plumbing must be minimum 20 above floor to prevent siphoning Cut 1 hole in cabinet
Download Pdf Manuals
Related Search