Home

Quatech DSE-410D Network Card User Manual

image

Contents

1. DSE 410D DATA A pl F DATA DATA A Gn 2 Wire RS 485 Connections One Twisted Wire Pair plus Ground RS 485 Devices Some RS 485 devices are marked opposite from the RS 485 standard that defines the Data B line as positive relative to Data A during a Mark state before enabling the transmitter and after transmitting before tri stating Ifthe RS 485 devices don t respond try swapping the Data B and Data A lines on to remaining If you want to connect 4 Wire RS 485 devices you can use the RS 422 Mode provided that the DSE 410D will be connected as a Master in a single master system If you have multiple masters you cannot use this device because it does not tri state the transmitter in RS 422 mode Document Number 940 0186 100 DSE 410D Owner s Manual Ouatech Inc 5675 Hudson Industrial Parkway Hudson OH 44236 330 655 9000 http www quatech com 13 14 DSE 410D Owner s Manual Document Number 940 0186 100 Ouatech Inc 5675 Hudson Industrial Parkway Hudson OH 44236 330 655 9000 http www quatech com 3 Install Ouatech DSE 410D Software The Windows based DSE 410D Manager and Virtual COM port software makes configuration fast and easy We recommend installing the Software to configure the DSE 410D unless you are not using Windows To install the DSE 410D Manager Install Virtual Com Uninstall Virtual COM programs Inserting the Quatech CD in the CD ROM will a
2. GND 5 GND GND Data Set Ready In DSR 6 CTSA Reguest To Send Out RTS 7 CTSB Clear To Send In CTS 8 RTSB Ring Indicator In RI 9 RTSA 7 Table 2 3 Serial Connection Pin outs for RS 232 RS 422 RS 485 10 DSE 410D Owner s Manual Document Number 940 0186 100 Quatech Inc 5675 Hudson Industrial Parkway Hudson OH 44236 330 655 9000 http www guatech com The DSE 410D has two DB 9 male connectors gt DSE 410D Port 1 Multi Interface dip switch selectable RS 232 RS 422 or RS 485 gt DSE 410D Port 2 RS 232 only RS 232 Connections In the RS 232 mode the ports are configured as DTE Data Terminal Equipment like a computer Modem Cable Straight Through Cable DB9 to DB9 DTE Device Computer or DSE 410D DTE to DCE Carrier Detector DCD CD 1 pa Receive Data Rx RD 2 pi Data Terminal Ready DIR 74 4 Data Set Ready osa 46 6 DSR Requestto Send Rts ar porr RTS CleartoSend crs rs por crs Rna indicator Ri P CM Signal Ground Common SG GND 45 p 15 enD AAA Null Modem Cable Crossover Cable DB9 to DB9 DTE Device Computer DTE to DTE DES Pint Pint DB When connecting to a PC or another DTE device use a null modem crossover cable When connecting to a DCE device that can normally be plugged into a PC use a straight through cable Set Flow Control to None for 3 wire RS 232 Refer to Appendix B for
3. 410D can be attached to your network using a standard Cat 5 Ethernet cable or to the Ethernet port of your computer using a crossover cable If a network connection is not available the DSE 410D can be configured in Console Mode from an RS 232 port using a VT100 Terminal Emulation program and an RS 232 crossover cable HyperTerminal is included with Windows and is recommended The DSE 410D Virtual COM Driver installs a virtual COM port which is viewable in the Windows Device Manager under Ports COM amp LPT This virtual COM port provides access to one of the ports on the DSE 410D the same as any other serial port legacy PCI USB or PCMCIA on the computer Any program running on the computer and using Windows based COM ports can access the serial devices attached to the DSE 410D The LAN becomes transparent to the serial device and the software running on the PC Document Number 940 0186 100 DSE 410D Owner s Manual 1 Ouatech Inc 5675 Hudson Industrial Parkway Hudson OH 44236 330 655 9000 http www quatech com Communication Modes The DSE 410D enables communication with serial devices over a LAN or WAN Serial devices are no longer limited to a physical connection to the PC COM port They can be installed anywhere on the LAN using TCP IP or UDP IP communications This will allow traditional Windows PC software access to serial devices anywhere on the LAN WAN network Direct IP Mode Direct IP connections allow
4. DATA A s GND DATA B F DATA A on to remaining 2 Wire RS 485 Connections One Twisted Wire Pair plus Ground RS 485 Devices Refer to Chapter 2 for more information Document Number 940 0186 100 DSE 410D Owner s Manual Quatech Inc 5675 Hudson Industrial Parkway Hudson OH 44236 330 655 9000 http www quatech com DSE 410D Owner s Manual Document Number 940 0186 100 Ouatech Inc 5675 Hudson Industrial Parkway Hudson OH 44236 330 655 9000 http www quatech com 14 Appendix E Warranty Quatech Inc warrants the Serial Device Server to be free of defects in materials and workmanship for a period of five 5 years from the date of purchase Quatech Inc will repair or replace any board that fails to perform under normal operating conditions and in accordance with the procedures outlined in this document during the warranty period Any damage caused by external causes including problems with electrical power servicing not authorized by Quatech negligent installation or operation failure to follow documented procedures abuse or general misuse of the product is not covered by the warranty Custom configured products are non refundable Quatech makes no express warranties except those stated in this paragraph and in the applicable warranty statements for specific products in effect on the date of invoice No representation is made regarding the suitability of this product for any
5. DB9 to DB25 Conversion Cables Document Number 940 0186 100 DSE 410D Owner s Manual 11 Quatech Inc 5675 Hudson Industrial Parkway Hudson OH 44236 330 655 9000 http www quatech com RS 422 Connections DSE 410D RS 422 Mode RS 422 Device RS 422 Connections w Flow Control In the RS 422 mode TXD lines are outputs and RXD lines are inputs Connect the TXDB line to the RXDB line of your device and the TXDA line to the RXDA line of your device If Flow Control is set for RTS CTS connect the RTSB line to the CTSB line of your device and RTSA to CTSA of your device Connect from CTSB to RTSB of your device and from CTSA to RTSB of your device If connecting to Receive Only RS 422 devices connect from TXDB and TXDA to the receive pairs on all your devices Ground is signal ground and provides a common mode reference for the RS 422 Receiver and Transmitters The RS 422 mode can be used for full duplex 4 wire RS 485 operation provided that the DSE 410D is acting as a sole master connecting to all the slave devices and all slave devices share the Receive signal lines to the master Set Flow Control for none and omit connections to RTS CTS line pairs 12 DSE 410D Owner s Manual Document Number 940 0186 100 Quatech Inc 5675 Hudson Industrial Parkway Hudson OH 44236 330 655 9000 http www quatech com RS 485 Connections Device 1 Device 2 Device 3
6. DC IN jack and then plug the supply into the local power outlet When power is applied the Red power light will illuminate The tip of the power plug is positive the sleeve is negative The standard 12VDC 500mA power supply for North America shipment is 120VAC 60Hz for Europe Pacific or UK it will be 230VAC or 240VAC 50Hz Reset Button This button soft resets the DSE 410D similar to removing re applying power The Reset Button is recessed to avoid accidental operation To reset the DSE 410D insert a small plastic tool press lightly and hold for 3 seconds The Link and Ready lights will go out and come back on If you change the Mode Switch settings you can press Reset to reboot and read the new settings Mode Switches DSE 410D Server Port 1 Set the switches for the mode desired then apply or cycle the power Mode SW1 SW2 SW3 RS 485 Operation OFF OFF OFF RS 422 Operation ON OFF OFF RS 232 Operation OFF ON OFF Default ON OFF ON Upgrade Firmware OFF ON ON Console Menu ON ON ON Table 2 2 Mode Switches The switches set the Multi Interface serial port to RS 485 RS 422 or RS 232 operation They also select the Server Console mode for Configuration Upgrade mode for new firmware downloading or Default to reset the DSE 410D to the original default settings 8 DSE 410D Owner s Manual Document Number 940 0186 100 Quatech Inc 5675 Hudson Industr
7. a COM port or to use standard Windows API calls for COM port access Running the Install Virtual COM port software adds a DSE 410D COM port to the computer that shows up in the Device Manager The COM number can be selected from a list of available numbers For example in a computer already having a COM1 and COM2 COM3 to COM 254 are available for the DSE 410D The virtual COM port looks like a standard COM port to most Windows based applications which allows the software to open a connection with the serial port located anywhere on the LAN When using the virtual COM port the DSE 410D is configured as a TCP or UDP Server 1 Select Install Virtual COM from your Programs list next to the DSE 410D Manager Start Programs Quatech SDS DSE 410D Install Virtual Com a meme L My Doce d E mall E arre Ci El roo Esp arran Linde E me E iker z a mea BA lt 0 Harare El Ena i a ii lona 0 Samp 3 ieri beter A Matia P a Wo Ere ib ono rt fires ji a Atar Benes so RET ERINE H Tar vanas P EJ intra LSB Araier arie Haja Pies Jh iiim Bese Document Number 940 0186 100 DSE 410D Owner s Manual 29 Quatech Inc 5675 Hudson Industrial Parkway Hudson OH 44236 330 655 9000 http www quatech com 2 The program searches the LAN for all available DSE 410D Servers when it starts then displays a list of those found in the Found Server window Highlight the Server at the IP Address you wish to use and then select OK
8. a password and make no changes Reset to end before Disconnect N Teina 12 32 149 230 44 DSE 410D Owner s Manual Document Number 940 0186 100 Quatech Inc 5675 Hudson Industrial Parkway Hudson OH 44236 330 655 9000 http www quatech com 10 Appendix A RS 232 RS 422 Loopback Connections RS 232 Loopback DTE DBS connections Receive Data 2 PRO 21 Data Terminal Ready RE CA Signal GroundiCommon SG Data Set Ready DSR 6 Request to Send RTS 7 P gt CleartoSend cts 484 Ring Indicator RI 494 For Transmit and Receive loopback connect only those lines When Flow Control setting on the Serial device server is set for RTS CTS those lines must be looped Usually DTR and DSR must also be looped The Flow Control setting for the program must match the Server settings The CD connection is needed by some terminal programs to simulate Carrier RS 422 Mode 1 DBS Male Outside RS 422 Loopback Connections tT The RS 485 Connections are half duplex either Receive or Transmit so another half duplex device must be used to check operation Document Number 940 0186 100 DSE 410D Owner s Manual A 1 Quatech Inc 5675 Hudson Industrial Parkway Hudson OH 44236 330 655 9000 http www quatech com DSE 410D Owner s Manual Document Number 940 0186 100 Ouatech Inc 5675 Hudson Industrial Parkway Hudson OH 44236 330 655 9000 http www quatech com 11 Appendix B R
9. and property damage of any kind direct incidental or consequential in regard to or arising out of the performance or form of the materials presented herein or in any software program s that may accompany this document Changes or modifications to this device not explicitly approved by Quatech will void the user s authority to operate this device Quatech Inc encourages and appreciates feedback concerning this document Please send any written comments to the Technical Support department at the address listed on the title page of this manual Table of Contents 1 ANG OMUCTHION AAA 1 A ET 1 Communication Modes a ean es 2 Direct IP Mode seten avi kk ernie rd 2 Virtual COM Mods ds 2 Heart Beat Feature MEA a E E EE tecaes 3 PP Arena dee ow aes KEETA decane ee A eee MNT E eee 3 Default DSE 410D Settings ccsccsssscsssscsssccssssssssscsssscssssssssessssseseees 4 Si O 5 PEOLOGONS 41243504 A II A O 5 ICAO ASS E A A A 5 O A A EN E AE A E EE 5 Serial Signals kord mums E A E a sad 5 Power amp Environment iereeenerseeeeeeeeeeenneeeeneneeeeeeeeenenneeeen enne 5 PIHASASIONS 2 42 28 LS A LS eh dbase osal MOE odes 6 Hardware and Included Accessories ccccccccceesssceceesseeeesssceceesseeecessseceessseeenes 6 Optional AEGESSOTIES 11414444 A dorian hashes 6 Configuration Options errerrrenneennennnenneenneenneennenenenenenenneneeennenneenaeennee 6 2 MHALAWAKE SS isast
10. connection or power is removed The host client communication software requests a connection to the specific IP address of the DSE 410D If the 24 DSE 410D Owner s Manual Document Number 940 0186 100 Quatech Inc 5675 Hudson Industrial Parkway Hudson OH 44236 330 655 9000 http www guatech com DHCP reassigns a different IP address the software will not be able to communicate with the hardware We recommend using a static IP address Net Mask The default LAN net mask is configured for a Class C address The user can change this if desired Default is 255 255 255 0 Gateway The Gateway IP address allows users to access the DSE 410D from outside the LAN MAC Address The MAC address is fixed not adjustable It is assigned in the factory Every Ethernet device manufactured has it own unique MAC address Link Status Shown in Telnet or Console mode only Link status automatically displays the type of Ethernet connection It will either display 10 BaseT or 100 BaseTX in full duplex or half duplex This will depend on the LAN switches and hubs used in the LAN topology Server Serial Port Select 1 or 2 One port is shown Make selections for Port 1 Multi Interface then select Port 2 RS 232 and make selections Using the DSE 410D Manager you must click Update to store settings for that port before changing to the other port Only the settings for the port shown are stored Using Telnet or Console mode Save stores s
11. date listed at the bottom of the menu will reflect the new firmware version Document Number 940 0186 100 DSE 410D Owner s Manual 41 Quatech Inc 5675 Hudson Industrial Parkway Hudson OH 44236 330 655 9000 http www quatech com 42 DSE 410D Owner s Manual Document Number 940 0186 100 Ouatech Inc 5675 Hudson Industrial Parkway Hudson OH 44236 330 655 9000 http www quatech com 9 Chapter 9 Console Mode Setup Before the DSE 410D is installed on a LAN the Console Mode can be used to change the settings from the Defaults Set the three DSE 410D switches to the ON position Connect a null modem cable between the Multi Interface serial port DSE 410D Port 1 on the Server and the COM port on the Computer See Chapter 5 for details of each Server Property Setting Apply power to the DSE 410D The power and ready LED will light Using your VT100 Terminal emulation program HyperTerminal can be used with Windows Set Connect Direct to connected COM port open the COM port to which your cable is attached at a baud rate of 9600 Data bits 8 Parity None Stop bits 1 and Flow control None To view the menu hit the space bar Use the arrow keys to select the desired field The following fields have a selection list to choose from DHCP UART Port Baud Rate Data Parity Stop Flow control TCP UDP port and Connection mode To view the options arrow to the field and select enter Quatech Inc Serv
12. particular purpose To request warranty service you must call Quatech at 800 553 1170 or submit the on line form at http www quatech com support support php within the warranty period with a description of the problem If warranty service is required Quatech will issue a Return Material Authorization RMA Number You must ship the defective product back to Quatech during the warranty period in its original or equivalent packaging prepay shipping charges and insure the shipment or accept the risk of loss or damage during shipment Quatech will ship the repaired or replacement products to you Quatech reserves the right to modify its warranty at any time in its sole discretion All software is provided subject to the license agreement that is part of the package Customer agrees that it will be bound by the license agreement once the package is opened or its seal is broken Quatech does not warrant any software under this Agreement Warranties if any for software are contained in the license agreement that governs its purchase and use THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE QUATECH S SOLE OBLIGATION AND CUSTOMER S SOLE REMEDY WITH RESPECT TO THE FOREGOING LIMITED WARRANTY SHALL BE TO AT ITS OPTION REFUND THE PURCHASE PRICE OR REPAIR REPLACE ANY DEFECTIVE PRODUCTS PROVIDED THAT QUATECH RECEIVES WRITTEN NOTICE OF SUCH DEFECTS DURING THE APPLICABLE WARRANTY PERIO
13. serial number of the product 3 Repair or upgrade instructions relative to the product E 2 DSE 410D Owner s Manual Document Number 940 0186 100 Ouatech Inc 5675 Hudson Industrial Parkway Hudson OH 44236 330 655 9000 http www quatech com
14. the Virtual COM port It will not change the settings stored in the DSE 410D Use the DSE 410D Manager to change Server Settings Document Number 940 0186 100 DSE 410D Owner s Manual 31 Quatech Inc 5675 Hudson Industrial Parkway Hudson OH 44236 330 655 9000 http www quatech com Use Device Manager to View New Ports 32 1 2 3 Confirm the Virtual COM port in the Device Manager Double click Ports to view the list of COM port numbers The installed Virtual COM port will be displayed as Ouatech DSE 410D COM D Device Manager Fie icion Wiee Help ME MY Cagney aisi lol CoM cies m Floppy k comiro era fh Floppy ciel dr oa B E aaa rari corral T apli T Mice and other point dera M Minne MA Meter siais Gh Crher devices 3 F Ports JOOKS LPT JT Port done F Conecte Port OOM A rmi Port LPT jt Gourd wire andi gare cores a Y Speen device a Leora Sora bus control lo Select the DSE 410D COM Double click it to bring up the Properties Select the Configuration or Port Settings tab This screen lets you change the Settings if needed DSE 410D Owner s Manual Document Number 940 0186 100 Quatech Inc 5675 Hudson Industrial Parkway Hudson OH 44236 330 655 9000 http www quatech com D5E 410D COM Properties Genesal Comfiguesion Drive Hap Ta CORKS 4 Use Cancel if you don t want to change any settings Use OK to change the settings Use Refresh in th
15. use HyperTerminal with Windows Quatech DSE 410D Manager using Windows 98 ME NT 2000 XP DSE 410D Manager software includes Search for Quatech DSE 410D on network Configure Server Properties Add Remove Virtual COM port in Windows and Firmware download for future revisions 6 DSE 410D Owner s Manual Document Number 940 0186 100 Quatech Inc 5675 Hudson Industrial Parkway Hudson OH 44236 330 655 9000 http www quatech com 2 Hardware This section covers indicators switch settings and connections Side View when vertically mounted 100M S Rassi DCN DSE 4 100 Serial Device Server Prya a Lini m Ready QUATECH R5 333 ES 2204155 Serial Serial Light Indication Power Red Power is applied Yellow 10 BaseT Ethernet or Green 100 BaseTX Ethernet connection established Ready Flashing Green system is ready Link Ethernet Connection A straight through RJ45 male Ethernet cable can be used to connect the serial server to an Ethernet hub switch or wall plate A crossover Ethernet cable can be used to make a connection directly to the RJ45 Ethernet port on a PC or laptop Document Number 940 0186 100 DSE 410D Owner s Manual 7 Quatech Inc 5675 Hudson Industrial Parkway Hudson OH 44236 330 655 9000 http www quatech com Top View ON RJ 45 female DC IN Reset SW 10 100M Power Connection Connect the included power supply to the
16. 1 is switch selectable as RS 232 422 485 DSE 410D Port 2 is always RS 232 DC ultra miniature phone jack 2 5mm Tip Sleeve Serial Signals RS 232 DTE TXD RXD RTS CTS DTR DSR DCD and GND RS 422 TXDB TXDA RXDB RXDA RTS RTS CTS 4 CTS and GND RS 485 Data B Data A and GND Baud Rate 110 bps to 230 4 kbps Parity none even odd Data Bits 7 8 Stop Bits 1 2 Power amp Environment Power Requirements 12 VDC 300 mA Operating Temperature 0 to 50 C 32 to 122 F Storage Temperature 20 to 60 C 4 to 140 F Humidity 0 90 Non Condensing Approvals CE FCC Document Number 940 0186 100 DSE 410D Owner s Manual Quatech Inc 5675 Hudson Industrial Parkway Hudson OH 44236 330 655 9000 http www quatech com Dimensions 3 35 x 4 5 x 0 90 in 8 5 x 11 5 x 2 3 cm Hardware and Included Accessories DSE 410D Ethernet Serial Device Server Power Supply 12VDC 500mA tip positive sleeve negative Area Dependent US power plug 120VAC 60Hz or International AC plug 220 240VAC 50Hz Manual paper copy of this manual CD ROM disc with software for Windows 98 ME NT 2000 XP and Quatech DSE 410D Manager Virtual COM Driver software Optional Accessories DSE 410D DIN Mounting clips for 35mm DIN Rail Configuration Options Console Mode using RS 232 with VT100 emulation Telnet using VT100 emulation Software for Console Mode or Telnet not included can
17. Control Protocol and UDP is User Datagram Protocol TCP UDP Port Set for each port This sets the port number for connection The default port numbers are 4000 and 4001 In all modes of operation Direct IP or Virtual Com the port number set in the DSE 410D menu must match the Virtual COM and socket software port settings As an example the Virtual COM default setting is TCP UDP Port 4000 If the port property is changed to 4001 then the Virtual COM TCP UDP Port will have to be changed to 4001 The DSE 410D Manager or Telnet Console configuration can change the setting for the hardware The Virtual COM port setting can be changed within the Device Manager of the computer in which it is installed Remote IP Address Set for each port This is a security feature activated by entering the IP address of the desired client The DSE 410D will only communicate with the listed IP address and all other requests for connection will be filtered out The DSE 410D is set to TCP or UDP Server in Connection Mode to use this feature 26 DSE 410D Owner s Manual Document Number 940 0186 100 Quatech Inc 5675 Hudson Industrial Parkway Hudson OH 44236 330 655 9000 http www quatech com The default setting is 255 255 255 255 If you are not using the Paired Mode we recommend not changing this setting until the application has been tested and is communicating properly Then you can activate the address filtering feature Update If using
18. D CUSTOMER MAY NOT BRING AN ACTION TO ENFORCE ITS REMEDIES UNDER THE FOREGOING LIMITED WARRANTY MORE THAN ONE 1 YEAR AFTER THE ACCRUAL OF SUCH CAUSE OF ACTION ALL EXPRESS AND IMPLIED WARRANTIES FOR THE PRODUCTS INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED IN DURATION TO THE WARRANTY PERIOD SET FORTH ABOVE AND NO WARRANTIES WHETHER EXPRESS OR IMPLIED WILL APPLY AFTER SUCH PERIOD SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU Document Number 940 0186 100 DSE 410D Owner s Manual E 1 Quatech Inc 5675 Hudson Industrial Parkway Hudson OH 44236 330 655 9000 http www quatech com OUATECH ITS LICENSORS DISTRIBUTORS AND SUPPLIERS INCLUDING ITS AND THEIR DIRECTORS OFFICERS EMPLOYEES AND AGENTS SHALL NOT BE LIABLE FOR ANY SPECIAL INDIRECT INCIDENTAL EXEMPLARY OR CONSEQUENTIAL DAMAGES INCLUDING WITHOUT LIMITATION LOST PROFITS BUSINESS INTERRUPTION LOST OR CORRUPTED DATA OR SOFTWARE OR ANY OTHER DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE PRODUCTS EVEN IF QUATECH OR ITS LICENSORS DISTRIBUTORS AND SUPPLIERS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES CUSTOMER AGREES THAT FOR ANY LIABILITY RELATED TO THE PURCHASE OF PRODUCTS OR SERVICES BUNDLED WITH THE PRODUCTS QUATECH IS NOT LIABLE OR RESPONSIBLE FOR ANY AMOUNT OF DAMAGES ABOVE THE AGGREGATE DOLLAR AM
19. Dual Port Multi Interface RS 232 422 485 Ethernet Serial Device Server Model DSE 410D Documentation Number 940 0186 100 TE CALMA ARES A Y CONNECT WITH RELIABILITY World Headquarters Quatech Inc 5675 Hudson Industrial Parkway Hudson OH 44236 Telephone 330 655 9000 Fax 330 655 9010 Home Page http www Quatech com Sales e Mail sales Quatech com Fax 330 655 9070 Technical Support http www Quatech com support support php Quatech Inc August 2003 Copyright Trademarks Disclaimer Feedback Copyright 2003 Quatech Inc All rights are reserved The information contained in this document cannot be reproduced in any form without the written consent of Ouatech Inc Any software programs that might accompany this document can be used only in accordance with any license agreement s between the purchaser and Quatech Inc Quatech Inc reserves the right to change this documentation or the product to which it refers at any time and without notice QUATECH is a registered trademark of Quatech Inc Other product and brand names listed in this manual may be trademarks of their respective owners The information in this manual is believed to be accurate and reliable at the time of posting Notwithstanding the foregoing Quatech assumes no responsibility for any damage or loss resulting from the use of this manual and expressly disclaims any liability or damages for loss of data loss of use
20. Found Server 3 After the COMInst window opens select the desired COM in the Map To options 4 Windows XP may provide a notice concerning Windows Logo testing for XP This XP feature simply indicates that these drivers have not yet undergone the Microsoft testing procedures required to use the Windows XP Logo on the packaging Driver compatibility is not affected Select Continue anyway to proceed with the installation 30 DSE 410D Owner s Manual Document Number 940 0186 100 Quatech Inc 5675 Hudson Industrial Parkway Hudson OH 44236 330 655 9000 http www quatech com Lomma 5 The Protocol TCP UDP IP Address and Port Number will mirror the settings of the selected serial server After setting both DSE 410D Serial Ports as Virtual COM ports Select Cancel on the Found Server form Note Your PC may have hardware COM ports and devices such as a Modem IR port or USB based COM ports that are not currently connected You may want to select a COM number above COM4 if problems occur The default Flow Control setting is None RTS CTS can be selected if used by the application program and serial hardware The DSE 410D Server must be set to match The settings of the Virtual COM port in the Device Manager and the DSE 410D Configuration menu must match If the settings do not match the Virtual COM port will not work If these settings are changed in the Device Manager it will only affect the operation of
21. O 27 ii DSE 410D Owner s Manual Document Number 940 0186 100 Quatech Inc 5675 Hudson Industrial Parkway Hudson OH 44236 330 655 9000 http www quatech com 6 Installing Virtual Com Port cccccsccccssscssssecssssccssnsscssssccessssssssceees 29 Use Device Manager to View New Ports e eeeseooseoosnoeonoooosoeosonooene 32 7 Removing a Virtual Com Port meimeeemeeenneonneonnnao enne nne nneee 35 Removing the Virtual COM port with the DSE 410D Management SOLCWALE oseiisnisecscessnssdsosneddesnsoccsosoonadacsnsscaases tendsnas daneassoseed esdsenesioosnsdsesnsocess 35 Removing the Virtual COM Port using Device Managet sccss0 36 Bo Vpgrade Modenast ie pans hess ae AR 39 Using Virtual COM or Serial Connections ssccssscssssscssssscssssssseee 39 9 Chapter 9 Console Mode Setup s ccsscccssscssrssssssccsssscssssscesssces 43 10 Appendix A RS 232 RS 422 Loopback Connections A 1 11 Appendix B RS 232 Connections sscccsscccesssessssccsssscesesccseees B 1 12 Appendix C RS 422 Connections sscccsssccesssccsssccssssccessscseees C 1 13 Appendix D RS 485 Connections wwwevsenneoonnnnoonneeo enne D 1 14 Appendix E Warranty csscccsssccssrsccssrsccssssccssssccsssccssssssssscesees E 1 Document Number 940 0186 100 DSE 410D Owner s Manual ii Quatech Inc 5675 Hudson Industrial Parkway Hudson OH 44236 330 655 9000 http www quate
22. OUNT PAID BY CUSTOMER FOR THE PURCHASE OF PRODUCTS UNDER THIS AGREEMENT SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU Please complete the following information and retain for your records DATE OF PURCHASE MODEL NUMBER DSE 410D PRODUCT DESCRIPTION Dual Port Serial Device Server SERIAL NUMBER All products returned to Quatech for either warranty or non warranty repair MUST be assigned a Returned Material Authorization RMA number prior to shipment This RMA number must be clearly marked on the exterior of the product s return packaging and in any correspondence to ensure proper routing and prompt attention To obtain an RMA number contact Quatech Technical Support Department at 1 800 553 1170 In order to prevent damage to returned merchandise during shipment please package electronic components in anti static shock proof materials For warranty repair returns please have the following information available when contacting the Technical Support department 1 Model number and serial number of the product under warranty 2 Repair instructions and or specific description of the problem For non warranty repairs or upgrades contact the Technical Support department for current repair charges and please have the following information available 1 Purchase order number to cover the cost of the service 2 Model number and
23. S 232 Connections RS 232 DTE RS 232 DB9M Signal Name Pin Carrier Detect In DCD 1 Receive Rx Data In RXD 2 Transmit Tx Data Out TXD 3 Data Terminal Ready Out DTR 4 Signal Ground GND 5 Data Set Ready In DSR 6 Reguest To Send Out RTS 7 Clear To Send In CTS 8 Ring Indicator In RI 9 Modem Cable Straight Through Cable DB9 to DB9 DTE Device Computer or DSE 410D DTE to DCE Carrier Detector DCD co Ai AM co Receive Data Rd RD 2 per RD Transmit Data T9 10 43 p 10 i Data Terminal Ready DTR 44 peti DIR Data Set Ready psr 6 Pd DSR Reauestto Send RTS fer porr RS earto Send crs 8 Eng indicator Ri fe Null Modem Cable Crossover Cable DB9 to DB9 DTE Device Computer DTE to DTE Data Terminal Ready 7 Ring Indicator COR Document Number 940 0186 100 DSE 410D Owner s Manual Quatech Inc 5675 Hudson Industrial Parkway Hudson OH 44236 330 655 9000 http www quatech com RS 232 Connections cont d Modem Cable Straight Conversion DB9 to DB25 DB9 DTEtoDCE DB25 RS 232Signalllames Pint Connections Pint TD Signal Ground Common SG GN Soldered to DB9 Metal Shield Null Modem Cable Crossover Cable DB9 to DB25 DB9 DTEtoDTE DB25 RS 232 Signal Names ___Pin Connections Pint Carrier Detector OCD co B 000 GH Fonn Receive Data Rx RD 2 py GND Ring ind
24. Step 7 When found Double Click the DSE 410D to bring up the Server Properties Configuration Screen If more than one DSE 410D shows up select the one that matches the Default IP Address shown on the bottom of the DSE 410D usually 192 168 0 1 Step 8 Refer to the Server Properties section Chapter 5 for details on the Configuration parameters for each field Configure and then Save Update Step 9 If you want to use Virtual COM ports with Windows install the Virtual COM port or ports on each computer requiring access to the DSE 410D Default DSE 410D Settings Server Name Quatech Serial Number Password Blank DHCP Disable IP Address 192 168 0 1 Net Mask 255 255 255 0 Gateway 192 168 0 254 MAC Address Fixed see bottom label Baud Rate 9600 Data Parity Stop 8 N 1 Flow Control None TCP UDP Ports TCP Port 1 4000 Port 2 4001 Connection Mode Server Remote IP Address 255 255 255 255 4 DSE 410D Owner s Manual Document Number 940 0186 100 Quatech Inc 5675 Hudson Industrial Parkway Hudson OH 44236 330 655 9000 http www quatech com Specifications Serial Memory 8K bytes per port LAN 10 100 Mbps Auto detecting 10 BaseT or 100 BaseTX Protocols TCP IP ARP DHCP Telnet HTTP UDP ICMP Indicators Power Red LED Link Yellow or Green 10 BaseT or 100 BaseTX Ready Flashing Green Connectors Ethernet single RJ 45 female Serial two 9 pin D type male DB9M DSE 410D Port
25. an be configured on your network using a standard Cat 5 Ethernet cable or to the Ethernet port on your computer using a crossover cable Use the DSE 410D Manager utility with Windows or use Telnet for configuration without Windows With Console configuration an RS 232 Crossover null modem DTE DTE cable is usually needed as the DSE 410D ports are configured DTE for RS 232 Set the mode switches to Console mode SW 1 ON SW 2 ON SW 3 ON before configuration Step 1 Decide which method to use for configuration and operation If using the Console mode for setup refer to the Console mode section Chapter 9 and Chapter 5 then power up the DSE 410D Document Number 940 0186 100 DSE 410D Owner s Manual 3 Quatech Inc 5675 Hudson Industrial Parkway Hudson OH 44236 330 655 9000 http www quatech com Step 2 Attach the DSE 410D to your network s switch or hub using a standard Cat 5 Ethernet cable or directly to the LAN port on your computer using a crossover cable You can connect your serial devices now if needed If using Telnet for setup refer to the Console mode section Chapter 9 and Chapter 5 then power up the DSE 410D Step 3 Ifusing Windows install the Ouatech DSE 410D Manager software on the configuring Computer Step 4 Power on the DSE 410D and check the status lights Step 5 Start the Ouatech DSE 410D Manager from your program menu Step 6 Select Search to find the DSE 410D on your network
26. applications using TCP IP or UDP IP socket programs to communicate with the asynchronous serial ports on the DSE 410D In this type of application the DSE 410D is configured as a TCP or UDP server The socket program running on the PC establishes a communication connection with the DSE 410D The data is sent directly to and from the serial port on the server Virtual COM Mode Use Install Virtual COM to add a driver that provides a Virtual COM port on the computer The new COM port shows up in the Device Manager Windows programs using standard Windows API calls are able to interface such Virtual ports When a program on the PC opens the new COM port it connects to the remote serial device connected to one of the ports on the DSE 410D OT E E Serial Device After connection the LAN is transparent to the program and serial device Applications are able to work just as if the serial device is connected directly to a physical COM port on the computer The Virtual COM port software converts the application s data into an IP packet sends it across the network to the DSE 410D which converts the IP packet back to serial data and sends the data out the serial port To use this mode the DSE 410D must be set to either TCP server or UDP server in the menu with a designated communication port number The virtual COM driver is the TCP or UDP client 2 DSE 410D Owner s Manual Document Number 940 0186 100 Quatech Inc 5675 Hu
27. cceessececeessececnsececeesaeeeceessecessseeeeeseeeesessess 20 SEVEN AM it E 20 TPA ddr Lt A talitas A A LE EL oss 20 SE A A A AA 21 COM NIG ni di id TT oes 21 A O O RAN 21 5 Server Properties Configuration ccccsscccssrsecesscccessccsssccssseceeees 23 Server Names s ssecovssisecsisescsetscesvocesdscocesecssescdsssescetseascousesssocessossesesbeedsesdeases 24 SO nei EEA EEA ENEA ESTEEN 24 DHCP icai aai aai aiaa ari ia 24 IP Address Netmask and Gateway Properti s mooo 24 TRPA Gress ut estes toler vitt e eet 24 NetMasiosirr tati ae aa lo es ar e a o oe in elated 25 CAN e Aid e 25 MAC AdGEESS iii ii A s 25 Link Status Shown in Telnet or Console mode only eeseessnnsooenee 25 Server Serial Port Select 1 or 2 eweveeeoneonoooooooooooonnonooooooooneonooooe oe 000 25 Baud Rate Set for each Pport ccsssccsssscssssssssscssssscssscssssssssessssssssssces 25 Data Parity Stop Set for each port ccssccsssscssssccssssccssssessssssssescsscee 25 Flow Control Set for each port cccsccsssscssscssssccssscssssssesssscsssecsssees 26 Connection Mode Set for each port sccssscssssscesssccssscesssscssseccssseees 26 TCP UDP Protocol Set for each port cccsssccsssccsssscsssssssssscssseccssess 26 TCP UDP Port Set for each port ccscccsssssssscssssscssccsssscsssssssssessseess 26 Remote IP Address Set for each port sccssscssssccsssscsssscessecsssecssces 26 AA
28. ch com iv DSE 410D Owner s Manual Document Number 940 0186 100 Quatech Inc 5675 Hudson Industrial Parkway Hudson OH 44236 330 655 9000 http www quatech com 1 Introduction The Quatech DSE 410D Dual Port Ethernet Serial device server provides Ethernet to Serial connections for RS 232 RS 422 or RS 485 devices The serial ports can be accessed over a LAN WAN using Direct IP Mode Virtual COM Port or Paired Mode connection The 10 100 Mbps Ethernet connection auto selects 10 BaseT or 100 BaseTX and indicates the type of connection with a bi color link light Features gt Dual Serial Ports One Multi Interface Selectable RS 232 RS 422 or RS 485 and One RS 232 10 100 Mbps Ethernet with Auto Selection LAN and WAN Communications Configurable as TCP or UDP Client or Server Device Driver Support Windows 98 ME NT 2000 XP Includes Quatech DSE 410D Manager Software for Windows Includes Virtual COM Driver Software for Windows Selectable Heart Beat Connection Firmware Download for Future Revisions Upgrades VVVVV VVV The Heart Beat Connection ensures reliable communications in Virtual COM port mode or with paired connections This feature restores the connections if communications are temporarily lost at either end due to loss of power or the Ethernet connection The Quatech DSE 410D Manager Software provides easy configuration of Ethernet and Serial port settings For configuration the DSE
29. dson Industrial Parkway Hudson OH 44236 330 655 9000 http www quatech com Heart Beat Connection The Heart Beat Connection provides an extra measure of reliable communications assurance in Virtual COM Port Mode or Paired Tunneling Mode This feature restores the TCP connection if communication is temporarily lost at either end due to loss of power or Ethernet connection Without this feature a device that loses a connection and stops communicating would not be able to reconnect without human attention to correct the problem A TCP data connection can be lost when there is a power failure or temporary loss of an Ethernet connection on either the client or server Ifa loss occurs the Heart Beat feature will try to reconnect the TCP data connection every 5 seconds until communications is established again The Heart Beat feature is not available when running in UDP Mode Ouick Start This section lists the steps needed to start using the DSE 410D Please familiarize yourself with the connections indicators and switches before beginning See chart and diagram on page 7 There are three ways to configure the DSE 410D for your network and serial devices We recommend the first method ifusing a Windows operating system 1 Ethernet connection using the Quatech DSE 410D Manager under Windows 2 Ethernet connection using the Telnet VT100 Terminal software 3 RS 232 connection in Console mode using VT100 Terminal software The DSE 410D c
30. e Device Manager if your version of Windows doesn t auto refresh Document Number 940 0186 100 DSE 410D Owner s Manual 33 Quatech Inc 5675 Hudson Industrial Parkway Hudson OH 44236 330 655 9000 http www quatech com 34 DSE 410D Owner s Manual Document Number 940 0186 100 Ouatech Inc 5675 Hudson Industrial Parkway Hudson OH 44236 330 655 9000 http www quatech com 7 Removing a Virtual Com Port The DSE 410D Management software s Uninstall Virtual COM port feature will remove the mapped COM port in the Device Manager of Windows 2000 and XP operating systems It may also be removed in the Device Manager of Windows 98 Me NT 2000 and XP Windows 98 users will also find a Remove Virtual COM feature in the programs file Removing the Virtual COM port with the DSE 410D Management software 1 At the Desk Top select Start Programs Ouatech SDS DSE 410D DSE 410D Manager 2 In the Manager window select Virtual COM Configuration Highlight the mapped COM port number to be removed SE 10D Manager Freeware Upgrade virtual COM List Banal Server Li 3 Select Uninstall Virtual COM button The Manager will ask for confirmation Select OK to complete the uninstall procedure Document Number 940 0186 100 DSE 410D Owner s Manual 35 Quatech Inc 5675 Hudson Industrial Parkway Hudson OH 44236 330 655 9000 http www quatech com OSE 4 100 Maniga Removing the Virtual COM Por
31. eco 7 Ethernet Connection sscccssssscccsssssccssssscccssssccccesssccccesssccccssssccccsssceecess 7 Power Comme tones sicsscscsssssscceresonovcssscntdosecevsecteseuccosecceuowsessutecessuccosesseuectsssee 8 AO sees 8 Mode Switches DSE 410D Server Port 1 ssssccssssssscesssscccssssceeeees 8 RS 483 MOde 20051000 it dl nasal tasud evel eu E aS thes tt eu 9 Selecting Internal RS 485 Bias Resistors rereerenneenneeneeeneeenenene 9 RS E422Mode ol lll Dobla TUUS 9 RS 232 Mode sitiada ao Dahlak iaa coa e 9 Default Sete o oo resideerus eed nes EE 9 Upsrade Mode tC ah ile else ne e So 10 Console MOE A ss sock cadet bide es M A eds 10 Serial ConneetilonS 3s 4issive A A 10 RS 232 COfinectloNS 15154 5 10 ee ins iia 11 RS 422 Connect ONS 13 is seoseid td cee cue n aia 12 RS 485 Connect Ons iii ii 13 Document Number 940 0186 100 DSE 410D Owner s Manual 1 Quatech Inc 5675 Hudson Industrial Parkway Hudson OH 44236 330 655 9000 http www quatech com 3 Install Ouatech DSE 410D Software wwnreeonnnvoonneeo onne 15 4 Using DSE 410D Manager eveevvevvooonnnneeo on nenoooonnnnooo on enne 19 Searching LAN for DSE 410D cssssccsssscsssscsssscssssscsssscssesssssescssseees 19 Firmware Doea raTa eA E E A E 20 Virtual COM Configuration weeeeeeeeeneererrenrenne ennem 20 Searching Vit adi 20 Uninstall Virtual COM uu cece ccccccccccec
32. er name Serial number Password DHCP IP address Netmask Gateway MAC address Link Status UART port Baud rate Data Parity Stop Flow control TC P UDP port Connection mode Remote IP address DSE 410D 0305000003 Disable 192 168 0 255 255 255 0 192 168 0 254 00 0b b4 11 05 68 10 Half Duplex 1 9600 8 N 1 None TCP 4000 Server 255 255 255 255 Status Save Default Running Reset Version 1 5 built date 8 18 03 Enter to select value Once all the changes have been made move to the Save field and select enter Document Number 940 0186 100 DSE 410D Owner s Manual 43 Quatech Inc 5675 Hudson Industrial Parkway Hudson OH 44236 330 655 9000 http www quatech com Quatech Inc Server name DSE 4100 Serial number 0305 Password Disable 12 32 143 16 Vou must restart the device before the new setting will take effect Restart now No TCP UDP port Connection mode Remote IP address Default Running version 1 4 built date 1 27 03 Enter to save configuration J IConmected 0123137 koera Bereni aou ars jam Ee Pea The restart message will appear Select Yes to save changes This is necessary to write the settings to the server To view the changes press the Space bar The screen will reappear If you assign a password to the server you will need to supply it before you can view the Configuration screen When you access the server with
33. ettings for both ports Baud Rate Set for each port The serial port baud rate on the DSE 410D must match the serial baud rate of the connected device unless using Virtual COM mode In Virtual COM mode the software program will establish serial settings Use the arrow keys to change the setting to the desired baud rate Data Parity Stop Set for each port Set this to match the data format used by the device connected when the Virtual COM mode is not being used Telnet Console Tab to the Data Parity Stop field and arrow to the desired selection Document Number 940 0186 100 DSE 410D Owner s Manual 25 Quatech Inc 5675 Hudson Industrial Parkway Hudson OH 44236 330 655 9000 http www quatech com Flow Control Set for each port The Flow Control setting must match the reguirements of the device connected Tab to the Flow Control field and arrow to None or RTS CTS Select None when setting DSE 410D Port 1 as RS 485 or 4 wire RS 422 Connection Mode Set for each port The Connection mode has two options Client and Server Select the Server mode to use a Virtual COM port or to usea TCP or UDP Socket program When set as Client the console mode or DSE 410D Manager software must be used to access the menu TCP UDP Protocol Set for each port Select TCP or UDP protocol If the application does not require a UDP connection select TCP TCP guarantees reliable communication with error checking TCP is Transmission
34. g directly to a Computer serial port connect a null modem cable Appendix B between the Computer RS 232 port and the DSE 410D Multi Interface DSE 410D Port 1 serial port Continued next page Document Number 940 0186 100 DSE 410D Owner s Manual 39 Quatech Inc 5675 Hudson Industrial Parkway Hudson OH 44236 330 655 9000 http www quatech com Lipar aie wrea Cod par Bored Saor tid 6 Select Browse locate the folder where you placed the firmware hex file select it Open and then select the Upgrade button 7 In the Serial Port selection options select the COM port number used to connect to the DSE 410D Ifusing the Virtual COM port select that number P rt Settings 40 DSE 410D Owner s Manual Document Number 940 0186 100 Ouatech Inc 5675 Hudson Industrial Parkway Hudson OH 44236 330 655 9000 http www quatech com 8 Next a serial menu is shown so you can match the Upgrade mode settings to DSE 410D Server serial settings which you noted in Server Properties The settings must match or the upgrade will fail B5E 410B Manager t Fitriana Upgrade 9 Upgrade progress will be shown until the Upgrade was successful message is shown Select and exit from the Manager software 10 When the upgrade is complete reset server Use Telnet Hyper Terminal Winsock or Console mode to access the menu Once the menu is open select the reset button When the DSE 410D is reset the build
35. ial Parkway Hudson OH 44236 330 655 9000 http www quatech com RS 485 Mode The RS 485 mode supports the Transmit and Receive Channels using 2 wire half duplex operation The data lines are differential with the Data B line positive relative to Data A in the Mark state Ground provides a common mode reference Refer to the Pin out table for connections Selecting Internal RS 485 Bias Resistors GEEL o m WH aa RS 485 Bias Do EEA a a You can select RS 485 Receiver Biasing from the DSE 410D if your network doesn t supply any Remove the two side cover screws slide the cover off then set the two bias jumpers shown open to enable biasing shorting RS 422 Mode The RS 422 mode supports 4 channels with full duplex operation for Receive Transmit RTS Request To Send and CTS Clear To Send The data lines are in differential pairs with the B lines positive relative to the A lines Ground provides a common mode reference To use handshaking Flow Control must be set to RTS CTS during configuration Refer to the Pin out table for connections RS 232 Mode The RS 232 mode supports eight channels plus Signal Ground and is configured as DTE like a computer Signals are single ended and referenced to Ground To use handshaking Flow Control must be set to RTS CTS during Configuration Refer to the Pin out table for connections Default Setting Use this mode to reset the original factory default settings when po
36. icator Rt Refer to Chapter 2 for more information B 2 DSE 410D Owner s Manual Document Number 940 0186 100 Quatech Inc 5675 Hudson Industrial Parkway Hudson OH 44236 330 655 9000 http www quatech com 12 Appendix C RS 422 Connections RS 422 Connections RS 422 RS 422 DB9M Signal Name Direction Pin Receive Data A In RXDA 1 Receive Data B In RXDB 2 Transmit Data B Out TXDB 3 Transmit Data A Out TXDA 4 Signal Ground GND 5 Clear to Send A In CTSA 6 Clear to Send B In CTSB 7 Reguest to Send B Out RTSB 8 Request to Send A Out RTSA 9 RS 422 Mode RS422 Device RS 422 Connections w Flow Control Document Number 940 0186 100 DSE 410D Owner s Manual C 1 Ouatech Inc 5675 Hudson Industrial Parkway Hudson OH 44236 330 655 9000 http www quatech com RS 422 Connections cont d RS 422 Mode RS 422 Device RS 422 Connections No Flow Control Refer to Chapter 2 for more information C 2 DSE 410D Owner s Manual Document Number 940 0186 100 Ouatech Inc 5675 Hudson Industrial Parkway Hudson OH 44236 330 655 9000 http www quatech com 13 Appendix D RS 485 Connections RS 485 RS 485 DB9M Signal Name Direction Pin Data B In Out DATAB 3 Data A In Out DATA A 4 Signal Ground GND 5 Device 2 Device 3 Device 1
37. ion Can be used to change the Virtual COM Settings IP address Port Flow Control Searching Server Can be used to find DSE 410D Servers on the network Uninstall Virtual COM Shown in Windows 2000 and XP Device Manager only Uninstall utility for Windows 98 and Me is located in Start Programs Quatech SDS DSE 410D folder These items are shown in the right side DSE 410D Manager Window Server Name The DSE 410D Servers are listed twice once for each port IP Address The IP address for both DSE 410D ports is the same for each port by design 20 DSE 410D Owner s Manual Document Number 940 0186 100 Quatech Inc 5675 Hudson Industrial Parkway Hudson OH 44236 330 655 9000 http www quatech com Protocol The TCP or UDP mode is shown COM Name The mapped COM number is shown Status The Status indicates the Mapped Virtual COM port condition Not Connected is shown when a program does not have the port Open Connected is shown when that mapped port is Open foruse Server Properties Screen Highlight the DSE 410D Server in the Manager Server window double click to open Servier Properties Karv serial port Baari rada Doi Piarika S bape ad 7 Fira conici BEE 83 Coresi rene EE TCPAUDP protocol EE 28 51 TEFJUDF port m Harzi F adder The Server Properties screen is used to Configure and store the Server settings Details for setting Properties are shown in the next chap
38. l y CSEE CMT sara Vos abou to uaaal ihe deena lors pour yar 4 The DSE 410D COM will be removed and the Device Manager window will refresh and display the remaining COM ports Document Number 940 0186 100 DSE 410D Owner s Manual 37 Quatech Inc 5675 Hudson Industrial Parkway Hudson OH 44236 330 655 9000 http www quatech com 38 DSE 410D Owner s Manual Document Number 940 0186 100 Ouatech Inc 5675 Hudson Industrial Parkway Hudson OH 44236 330 655 9000 http www quatech com 8 Upgrade Mode New DSE 410D firmware may become available through our Web site for installation into the DSE 410D The software can be downloaded to the DSE 410D using either the Virtual COM or hardware COM port Using Virtual COM or Serial Connections 1 Make a folder to receive the firmware file Download the compressed software file from our website to your folder Unzip or expand the file into the hex format so it will be ready to download to the DSE 410D Before Setting the DSE 410D to Upgrade mode we recommend setting the DSE 410D Server baud rate to 115 2K if using a hardware COM port This will provide the fastest download Set DSE 410D Dip Switches to Upgrade Switch 1 OFF Switch 2 ON and Switch 3 ON As shown here RJ 45 female DC IN Reset SW 10 100M If using a Virtual COM port to upgrade identify the virtual COM number and address used for the Multi Interface port If connectin
39. ntering a password activates a security feature on the DSE 410D Once a password is entered it will be reguired to access the menu and make changes DHCP DHCP servers are a part of numerous LAN management systems The DHCP field has two selections Disable or Enable Select then Tab to another property Telnet Console Arrow to the desired selection and select enter Disable is the normal default setting When enabled DSE 410D will send a DHCP reguest to the DHCP server which will assign a dynamic IP address net mask and gateway to the DSE 410D Ifa DHCP server is not available on the network the DSE 410D will time out after 10 seconds and the default values will remain IP Address Netmask and Gateway Properties The Network Administrator can provide IP Address Netmask and Gateway address information All three fields will have to conform to your LAN for proper operation IP Address Assign a static IP address using this property A static IP address is retained and used each time the Server is powered up or starts restarts Software or hardware attempting to access the Server will need to use the static address to access the Server The Network Administrator will assign establish the static address or group of addresses to be used The default IP address such as IP 192 168 0 1 is shown on a label affixed to the bottom cover A dynamic address assigned by the DHCP server may change if the DSE 410D looses the Ethernet
40. p www quatech com 5 The Setup Status window displays the progress of the installation 05E 4100 Setup DST VEO Saw eon de ee Ge loading C Prepa eN DBE allt DO doo ei 6 Select Finish when the Install Shield Wizard Complete appears DSE 4100 Setup Drea kastid mand Loira mup han ie el er DEA ee ee When the installation is complete the Install window closes You can now start the DSE 410D Manager software If the Management software is loaded in the default location use Start Programs Quatech SDS DSE 410D Select DSE 410D Manager to open Document Number 940 0186 100 DSE 410D Owner s Manual 17 Quatech Inc 5675 Hudson Industrial Parkway Hudson OH 44236 330 655 9000 http www quatech com If you have not already done so connect the DSE 410D to your network using a Cat 5 Ethernet cable or to the LAN port on your computer using a crossover cable and then apply power The Power indicator should light Red the Link light should indicate which type of Ethernet connection has been made and the Ready LED will flash indicating that you can begin configuration 18 DSE 410D Owner s Manual Document Number 940 0186 100 Ouatech Inc 5675 Hudson Industrial Parkway Hudson OH 44236 330 655 9000 http www quatech com 4 Using DSE 410D Manager The DSE 410D Manager software performs several functions Searches the LAN for installed DSE 410D Servers Configures the DSE 410D Server for operation Unins
41. r current property Enter Select Update or Cancel The Keyboard keys can be used as listed below for Telnet or Console The default Telnet port for Configuration is 23 There are a few pre defined keys to move around the menu and to save changes Space Bar To refresh the configuration page Tab To move the cursor to next field Back Space To move the cursor to previous field Arrow Keys To move the cursor around the configuration page Enter Telnet only To open 2 window of selections confirm a selected change or to activate the save default reset and status Note Using Ping after before Configuration will check communications with the selected IP address At run prompt enter Command Next enter Ping xxx xxx xxx xxx using the IP address on Command line To check your computer IP address gateway enter IPCONFIG at prompt When done enter EXIT to return to Windows and close DOS window VVVV Document Number 940 0186 100 DSE 410D Owner s Manual 23 Quatech Inc 5675 Hudson Industrial Parkway Hudson OH 44236 330 655 9000 http www quatech com Server Name You can enter a new Server Name of up to 16 characters If you have more than one DSE 410D Server on the LAN we recommend that you assign a new name to each When the DSE 410D Manager finds DSE 410D Servers on the LAN it displays the Server name and IP Address allowing the user to distinguish between several DSE 410D Servers Password E
42. t using Device Manager The screen shots were taken from a Windows XP operating system 1 On the Desktop select Start Settings Control Panel Select the system icon when the manager window opens E Control Panel G O pam pum A Ebbw e Corra Farai pea Peta nore l A Gee TN ira Lae Bi is bn Spars Tha Adi Mc Leo ie pa a Pe sac rae wn eed Wt ee Pe he ds deca cad A hee Be men of one ce Tie bing Dieii Hinge leili JU Hala Paddel de cl bi pride ful ni pad ce Md ira H ahi ds Piihi La JC 36 DSE 410D Owner s Manual Document Number 940 0186 100 Quatech Inc 5675 Hudson Industrial Parkway Hudson OH 44236 330 655 9000 http www quatech com 2 Select Device Manager in the Systems Properties window In the Device Manger window select the next to Ports COM amp LPT to expand Device Meneser Fae irm W Help 0905 ATAN EE Mpi kri ae FAA dba ih Popper disk morireiieri fh Poppy dih oe e EA DE ATAATA orein iori i ends y eho ard other poring devo 4 E tonne i BE rari AADA Sh ther davices F Pos OMS LIFT F Qomerarecanore Pon P hta F Communicators Por DMT if Pov Por PTI a li und accord gene conde Gyre aera Mt Universal Su tel Bum comia 3 Highlight DSE 410D COM to be removed go the Action tab at the top of window and select uninstall A confirm Device Removal window will appear Select OK to procedure Confirm Device Remova
43. talls Virtual COM ports Configures Virtual COM ports Upgrades Firmware VVVVV Connect the DSE 410D to the LAN using a standard Cat 5 Ethernet cable or to the LAN port on your computer using an Ethernet crossover cable 2 Apply power The Red Power indicator will light the Link indicator lights when an Ethernet connection is made and the Ready indicator will flash See the Hardware chapter for more information The DSE 410D Manager software can now be started and used to Search for all connected DSE 410D Server Each Server will be found and displayed by name and IP address in the Server Window Searching LAN for DSE 410D 1 Select the DSE 410D Manager from your Programs menu Use Start Programs Ouatech SDS DSE 410D DSE 410D Manager E oi i a El vances Verda Paar a t rke Mere Document Number 940 0186 100 DSE 410D Owner s Manual 19 Quatech Inc 5675 Hudson Industrial Parkway Hudson OH 44236 330 655 9000 http www quatech com 2 Inthe sidebar icon window select the icon labeled Searching Server The Searching window is shown until all active DSE 410D Servers on the LAN are listed in the main DSE 410D Manager Window EBE 4100 ela age Es ori mi rue COM Configures am id Cel Lie rial red L These items are shown in the sidebar icon window of the DSE 410D Manager Firmware Upgrade This is used when downloading new firmware to the DSE 410D Server See Chapter 8 Virtual COM Configurat
44. ter The DSE 410D Server Serial Port 1 is the Multi Interface port Server Serial Port 2 is the RS 232 port Document Number 940 0186 100 DSE 410D Owner s Manual 21 Ouatech Inc 5675 Hudson Industrial Parkway Hudson OH 44236 330 655 9000 http www quatech com After Configuring as needed click Update to Store the Configuration in the Server After storing the configuration and answering Yes to Restart the Server is automatically reset Repeat Search to verify changes Continued in next chapter 22 DSE 410D Owner s Manual Document Number 940 0186 100 Quatech Inc 5675 Hudson Industrial Parkway Hudson OH 44236 330 655 9000 http www quatech com 5 Server Properties Configuration The Ouatech DSE 410D can be configured in one of three ways gt DSE 410D Manager Software gt Telnet Mode gt Console mode The Server Properties Configuration screen shown in the previous chapter displays a box for each property Telnet or Console configuration will show similar configuration items In the DSE 410D Manager you can use the mouse to select the property and parameters for each property Keyboard keys can be used as listed Tab Move to next configuration property Tab Shift Move back to previous property Left Arrow Change values or contents of current property or Move up the list of items for current property Right Arrow Change values or contents of current property or Move down the list of items fo
45. the Server Properties screen for Configuration click the Update button to store the configuration settings This also resets the Server Search to locate the Server with new settings If using the Telnet or Console mode Tab to Save then press Enter There are five options shown at the bottom of the menu Save Default Running Reset and Status Use Tab Backspace or arrow keys to move the cursor to the option position and then press Enter Save stores the configuration data to DSE 410D flash memory and resets it Default restores the editing configuration data to factory default settings Running restores the editing configuration data to the values stored in the flash Reset re boots the DSE 410D saving the change menu settings Status displays how many Ethernet packets and serial bytes are transmitted and received A refresh button is available to update the displayed figures Refresh Space Bar Press to refresh the configuration page Document Number 940 0186 100 DSE 410D Owner s Manual 27 Quatech Inc 5675 Hudson Industrial Parkway Hudson OH 44236 330 655 9000 http www quatech com 28 DSE 410D Owner s Manual Document Number 940 0186 100 Ouatech Inc 5675 Hudson Industrial Parkway Hudson OH 44236 330 655 9000 http www quatech com 6 Installing Virtual Com Port The Virtual COM Port software enables Windows based applications to use the serial port on the DSE 410D Server as
46. utomatically launch the Install Shield Wizard 1 To manually start the software installation select the Start button on the desktop At the Run command line type D start exe and then select OK D is the drive letter for the CD ROM TC ij Type the sere of a pogan folder derert e Imemetresurce and Windows eal apes it for pre Spee esses ene cues mmm 2 The Install Shield Wizard window automatically displays to begin the setup procedure Install5hicid Mira Setup it piping Pa ral Wired hidalgo pou lhecugh the rec of he cebup promece Please rad A 725 Document Number 940 0186 100 DSE 410D Owner s Manual 15 Quatech Inc 5675 Hudson Industrial Parkway Hudson OH 44236 330 655 9000 http www quatech com 3 Click Next when the Quatech DSE 410D Setup window appears D5E 4100 Setup wh a Hs raid od bea DEE ae Ti abarh h lic rl art E CD aa paa copa To cora cki Hasi 4 In the Choose Destination Location window click Next to install the manager software in the default location recommended Select Browse to install into a user selected directory 0546 4100 Setup Chata Nailin Locas Sed Haller do E ll rial Via Tapal gonial DEL gt 000 a log biia Ed a rental Sc ho A AR athe kolima iPega ecc LSE A 16 DSE 410D Owner s Manual Document Number 940 0186 100 Quatech Inc 5675 Hudson Industrial Parkway Hudson OH 44236 330 655 9000 htt
47. wered on Document Number 940 0186 100 DSE 410D Owner s Manual Quatech Inc 5675 Hudson Industrial Parkway Hudson OH 44236 330 655 9000 http www quatech com Upgrade Mode You can install newly revised firmware for the DSE 410D using RS 232 connections from a PC through either the DSE 410D Manager or through the Virtual COM port See Chapter 8 for details Console Mode The Console mode provides access to the configuration menu using RS 232 connections Connect a null modem crossover cable between the Multi Interface port and one of the computer s RS 232 serial ports The DSE 410D Serial ports are wired as DTE like a computer using DB9M connectors so a crossover cable must be used to connect to another DTE port In Console mode the default serial port settings are 9600 baud 8 data bits No parity and 1 stop bit With Windows you can use HyperTerminal with VT100 terminal emulation for Console mode configuration Use the default settings only if they have not been changed during a prior installation configuration See Chapter 7 for details Bottom View DBSM DBSM male male Port 2 4 40 Hex threads cert Serial Connections RS 232 DTE RS 232 DBIM RS 422 RS 485 Signal Name Pin Carrier Detect In DCD 1 RXDA 7 Receive Rx Data In RXD 2 RXDB Transmit Tx Data Out TXD 3 TXDB Data B DataTerminal Ready Out DTR 4 TXDA Data A Signal Ground

Download Pdf Manuals

image

Related Search

Related Contents

Velleman SOL5N battery charger  

Copyright © All rights reserved.
DMCA: DMCA_mwitty#outlook.com.