Quatech 2.4GHz Stereo Receiver User Manual
Contents
1. is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Note The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment Such modifications could void the user s authority to operate the equipment2. reception e Change the channel on both transmitter and receiver and make them the same e f there is a microwave oven in use in the path between the transmitter and receiver remove the microwave oven or turn it off e Make sure the transmitter and receiver are within range of each other range of approximately 300 feet 100 meters in a clear line of sight Care and Maintenance e Keep all its parts and accessories out of the reach of young children e Do not attempt to open the case Non expert handling of the device may damage it e Keep dry Precipitation humidity and liquids contain minerals that will corrode electronic circuits e Do not use or store in dusty dirty areas Moving parts may be damaged e Do not store in hot areas High temperatures can shorten the life of electronic devices and warp or melt certain plastics e Do not store in very cold areas When the A V sender warms up to its normal temperature moisture can form inside the case which may damage electronic circuit boards e Do not drop knock or shake it Rough handling can break internal circuit boards e Do not use harsh chemicals cleaning solvents or strong detergents when cleaning e Operate this product using only the power supply included with it e Do not overload electrical outlets or extension cords as this can result in fire or electric shock FCC Label Compliance Statement This device complies with Part 15 of the FCC Rules Operation
3. the unit should light up Wall Outlet Receiver Specifications Transmitter Receiver A V Transmitting Frequency 2 4GHz A V Signal Range 100 meters 300 feet clear line of sight Antenna Built in antenna Channel 4 selectable channels Audio Stereo audio input and output Video Composite input and output Dimensions 12 5 x 8 x 2 5 cm for transmitter receiver Weight 125g for transmitter receiver Power DC6V 500mA Operating Temperature 0C 40 C 32 F 104 F Providing the latest technologies to our customers is our responsibility therefore we reserve the right to change the specifications without prior notice Troubleshooting If you are not getting any signal at all e Check that the transmitter and receiver are properly connected to the A V device from which you want to send receive the A V signal e Make sure the transmitter and the receiver are turned on e Check power switches on the remote TV and video source VCR DVD player satellite receiver etc e Make sure power plugs are pushed all the way in e Check all cable connections e Check the CHANNEL switch on both transmitter and receiver are set to the same number e If you connect the receiver to a TV through an RF modulator check that the TV is tuned to the same channel as the TV Channel switch on the RF modulator 3 or 4 If the signal is poor or there is interference e Adjust the transmitter by rotating orientations until you get the best
4. 2 4GHz Wireless A V Sender User Manual Package Contents e Transmitter x 1 e Receiver x 1 e Base stand x 2 e Audio Video cable x 2 e Power adaptors DC6V x 2 e User manual x 1 Note The transmitter and the receiver look very similar You can find transmitter and receiver labels on the side of the units See Fig 1 Receiver NL Receiver Product Layout Transmitter Transmitter Receiver See Fig 2 and Fig 3 1 Power Channel Indicator N a Transmitter 2 Channel Select Button Select the channel by pressing the tact switch to the channel number you want Select the same channel both on the transmitter and the receiver Audio Jack Red Audio Jack White Video Jack Yellow Power On Off Power Adaptor Plug OF a w i Receiver Transmitter i 5 H ens Vz Transmitter Receiver Setting Up Before you make the connection e Set the channel by pressing the select button on the front of the transmitter and the receiver to the same channel 1 Setting up the Transmitter 1 1 Connect the Transmitter to an A V device Connect the mini plug of the provided A V cables to the A V jack on the rear of the transmitter connect the other end of the cables to the A V jacks of the A V device labeled AUDIO VIDEO OUT See Fig 4 U VIDEO AUDIO Transmitter Satellite receiver DVD VCD Note 1 If the A V equipment has only one output for audio mon
5. o sound only connect the white plug to that single audio output jack 1 2 Power Supply a Plug one end of the provided power adaptor into a wall outlet and the other end into the rear of the transmitter See Fig 5 b Turn on the transmitter The LED on the front of the unit should light up Wall Outlet Transmitter 2 Setting up the Receiver 2 1 Connect the Receiver to a TV A V Connect for TV with A V Input Jacks Connect the mini plug of the provided A V cables to the A V jack on the rear of the receiver connect the other end of the cable to the A V jacks on the TV labeled AUDIO VIDEO IN See Fig 6 A V Cable Receiver RF Connection for TV without A V Input Jacks If there is no A V input jacks on your TV you will need to get an RF modulator available at your local electronics store to make the connection between TV and receiver See Fig 7 Receiver A V Cable Ir R CEE CH 3 4 VIDEO AUDIO IN RF OUT RF Modulator Note 1 Connect the yellow plug to the jack labeled VIDEO the red plug to the jack labeled AUDIO RIGHT and the white plug to the jack labeled AUDIO LEFT Note 2 If the TV has only one input for audio mono sound only connect the white plug to that single audio in jack 2 2 Power Supply a Plug one end of the provided power adaptor into a wall outlet and the other end into the rear of the receiver See Fig 8 b Turn on the receiver The LED on the front of
Download Pdf Manuals
Related Search