Philips 32PFL3404/77 CRT Television User Manual
Contents
1. Use Philips EasyLink Your TV supports Philips EasyLink which uses the HDMI CEC Consumer Electronics Control protocol EasyLink compliant devices that are connected through HDMI connectors can be controlled by a single remote control Note Philips does not guarantee 100 interoperability with all HDMI CEC devices Note The EasyLink compliant device must be switched on and selected as the source EasyLink features One touch play When you connect your TV to devices that support one touch play you can control your TV and the devices with one remote control For example when you press Play on your DVD remote control your TV automatically switches to the correct channel to show the DVD content One touch standby When you connect your TV to devices that support standby you can use your TV remote control to put your TV and all connected HDMI devices in standby mode Tip e Press TV to switch back to the antenna source from EasyLink mode 20 EN Enable or disable EasyLink Note Do not enable Philips EasyLink if you do not intend to use it 1 Press MENU 2 Select Installation gt Preferences gt EasyLink J Select On or Off Use a Kensington lock There is a Kensington security slot at the back of the TV Prevent theft by looping a Kensington lock between the slot and a permanent object such as a heavy table 8 Product infor2. liquids such as vases should not be placed on this apparatus 22 Battery Usage CAUTION To prevent battery leakage that may result in bodily injury property damage or damage to the unit Install all batteries correctly with and alignment as marked on the unit Do not mix batteries old and new or carbon and alkaline etc Remove batteries when the unit is not used for a long time N ANTENNA LEAD IN WIRE ANTENNA DISCHARGE UNIT NEC SECTION 810 20 GROUNDING CONDUCTORS NEC SECTION 810 21 GROUND CLAMPS POWER SERVICE GROUNDING ELECTRODE SYSTEM NEC ART 250 PART H Note to the CATV system installer this reminder is provided to call the CATV system installer s attention to Article 820 40 of the NEC that provides guidelines for proper grounding and in particular specifies that the cable ground shall be connected to the grounding system of the building as close to the point of cable entry as practical Contents 1 Notice 2 2 Important 3 3 Your product 5 Product overview 3 4 Use your product 7 Switch your TV on off or to standby 7 Switch channels 7 Watch connected devices 8 Adjust TV volume 8 5 Use more of your product 9 Access TV menus 9 Change picture and sound settings 9 Create and use lists of favorite channels 12 Use timers 13 Use child control 13 Use the TV clock 14 Update the TV software 14 Change TV preferences 15 Start a TV demo 15 Reset the TV to factory settings 15 6 I
3. Remote control overview 5 technical specifications 21 troubleshooting 23 S Sleep timer 13 Smart settings 9 11 EN 25 English Software update analog 15 version 15 Sound settings 11 Standby troubleshooting 23 T Technical specifcations 21 Timer on timer 13 sleeptimer 13 standby 13 Transmission troubleshooting 23 Troubleshooting 23 TV adjust volume 8 menu 9 software 14 standby 7 switch channels 7 switch off 7 switch on 7 troubleshooting 23 tuner technical specifications 21 wall mount 22 TV lock lock channels 14 lock connected devices 14 PIN code 23 V Video format video format technical specifications 21 Volume adjust 8 26 EN PHILIPS 2009 Koninklijke Philips Electronics N V All rights reserved Document order number 72 CLICK0 X771A
4. be prompted to enter your new code 8 Enter the new code using the Numeric buttons L gt You will be prompted to re enter the new code for confirmation Tip f you forget your code enter 0711 to override any existing codes Lock or unlock the TV Locking the TV prevents your child from accessing all channels and connected devices 1 Press MENU 2 Press AVP to select Features gt TV lock J Press to enter TV lock L A screen prompting you to enter code appears Enter your code Press AY to select Lock or Unlock Press OK L gt All channels and connected devices are locked or unlocked ON U1 A 7 Press MENU to exit Lock or unlock one or more channels When watching TV press OK to display the channel grid Press AY4b to select a channel to lock or unlock Press OPTIONS Press AY to select Lock Unlock chan UAW N For each selection press OK to lock or unlock the channel Use the TV clock You can display a clock on the TV screen The clock displays the current time using time data received from your TV service operator Display the TV clock 1 When watching TV press OPTIONS L gt The TV options menu appears 2 Select Clock 3 Press OK The clock is displayed Note The clock is disabled automatically after ten minutes To disable the clock before that repeat this procedure Set the TV clock 1 Press MENU 2 Sele
5. product Access TV menus Menus help you to install channels change picture and sound settings and access other features 1 Press MENU L gt The menu screen appears Smart picture Contrast Sound Brightness Color Features Sharpness Noise reduction Installation Tint Color Temperature Software update Dig Crystal Clear Li 2 Press the AVP to select and navigate through one of the following menus e Picture Adjusts the picture setting for optimal viewing e Sound Adjusts the sound setting e Features Accesses different features like timer TV lock and demo e Installation Selects channel installation menu adjusts preferences and resets the TV to factory settings e Software update Updates the TV software 3 Press OK to confirm your choice Tip Change picture and sound settings Change picture and sound settings to suit your preferences You can apply pre defined settings or change settings manually Use smart picture Use smart picture to apply pre defined picture settings 1 Press O PICTURE L gt The Smart picture menu appears 2 Press AV to select one of the following smart picture settings e Personal Lists customized personal picture settings e Sports Maximizes picture settings e Standard Adjusts picture settings to suit most environments and types of video e Movie Applies picture settings ideally suited for movie viewing e
6. the cart apparatus combination to avoid injury from tip over Unplug this apparatus during lightning storms or when unused for long periods of time 14 Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as power supply cord or plug is damaged liquid has been spilled or objects have fallen into apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped 15 This product may contain lead or mercury Disposal of these materials may be regulated due to environmental considerations For disposal or recycling information please contact your local authorities or the Electronic Industries Alliance www eiae org 16 Damage Requiring Service The appliance should be serviced by wp qualified service personnel when The power supply cord or the plug has been damaged or Objects have fallen or liquid has been spilled into the appliance or EXAMPLE OF ANTENNA GROUNDING AS PER NATIONAL ELECTRICAL CODE NEC GROUND CLAMP ELECTRIC SERVICE EQUIPMENT C The appliance has been exposed to rain or D The appliance does not appear to operate normally or exhibits a marked change in performance or E The appliance has been dropped or the enclosure damaged 17 Tilt Stability All televisions must comply with recommended international global safety standards for tilt and stability properties of its cabi
7. video input from a computer TV ANTENNA Signal input from an antenna cable or satellite 9 SERV U For use by service personnel only AV OUT VIDEO and AUDIO L R 18 EN Audio and video output to analog devices such as another TV or a recording device 6 AV IN VIDEO and AUDIO L R Analog audio and video input from analog or digital devices such as DVD players satellite receivers and VCRs T CVI 1 2 Y Pb Pr and AUDIO L R Analog audio and video input from analog or digital devices such as DVD players or game consoles Side connectors 1 SERVICE For software update 2 HDMI Digital audio and video input from high definition digital devices such as Blu ray players 3 VIDEO Composite video input from analog devices such as VCRs 4 AUDIO L R Audio input from analog devices connected to VIDEO a Stereo audio output to headphones or earphones Connect a computer Before you connect a computer to the TV e Set the monitor refresh rate on your computer to 60Hz e Press amp 3 FORMAT and change the TV picture format to Unscaled Connect a computer with one of the following connectors Connections via DVI or VGA require an additional audio cable HDMI cable and HDMI DVI adaptor PC AUDIO IN PC IN AUDIO HDMI cable VGA cable e DVI HDMI cable EN 19 English
8. Game Applies picture settings maximized for fast moving games e Energy saving Applies low energy picture settings 3 Press OK to confirm your choice tL The selected smart picture setting is applied When the menu is on CH functions as Page Up Down Press MENU at any time to exit the menu Press lt gt BACK A CH to move back one screen Manually adjust picture settings 1 Press MENU 2 Press OK to select Picture Ly The Picture menu appears 3 Press AVP to select from the following settings and adjust EN 9 English Smart picture Accesses pre defined smart picture settings Contrast Adjusts the intensity of bright areas keeping dark areas unchanged e Brightness Adjusts the intensity and details of dark areas e Color Adjusts color saturation e Hue Compensates color variations in NTSC encoded transmissions e Sharpness Adjusts the level of sharpness in image details e Noise reduction Filters and reduces noise in an image e Color temperature Introduces more orange tones or blue tones to the picture e Dig CrystalClear Digitally adjusts picture quality to optimal contrast color and sharpness e Dynamic contrast Automatically enhances contrast in an image e Dynamic backlight Adjusts the brightness of the TV backlight to match lighting conditions e Color enhancement Makes colors more vivid and improves the re
9. Register your product and get support at www philips com welcome 32PFL3404 77 32PFL3404 78 42PFL3604 77 42PFL3604 78 pHILIPS EN User manual PHILIPS IMPORTANT SAFETY INSTRUCTIONS Read before operating equipment Read these instructions Keep these instructions Heed all warnings Follow all instructions Do not use this apparatus near water Clean only with a dry cloth Do not block any of the ventilation openings Install in accordance with the manufacturers instructions Do not install near any heat sources such as radiators heat registers stoves or other apparatus including amplifiers that produce heat Do not defeat the safety purpose of the polarized or grounding type plug A polarized plug has two blades with one wider than the other A grounding type plug has two blades and third grounding prong The wide blade or third prong are provided for your safety When the provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet 10 Protect the power cord from being walked on or pinched particularly at 11 amp 1 m plugs convenience receptacles and the point where they exit from the apparatus Only use attachments accessories specified by the manufacturer Use only with a cart stand tripod bracket or table specified by the manufacturer or sold with the apparatus When a cart is used use caution when moving
10. Tip e When watching TV press amp OPTIONS gt Mark as favorite to save the current channel into a favorite list Remove a channel from a favorite list Note Select the favorite list to edit before removing a channel When watching TV press OK to display the channel grid 2 Press OPTIONS tL The channel options menu appears Press OK to enter Show favorite ch A GJ Press AY to select a favorite list and press OK to confirm the choice Press AV to choose the channel that you wish to remove from the list Press OPTIONS Press AY to select Unmark as fav Press OK Ls The channel is removed from the favorite list COND UI Use timers You can set timers to switch the TV on or switch to standby at a specified time Automatically switch the TV to standby sleeptimer Sleeptimer switches the TV to standby after a pre defined period of time You can always switch off your TV earlier or reset the sleeptimer during the countdown Press MENU 1 2 Select Features gt Sleep timer L gt The Sleep timer menu appears 3 Press lt P to set the sleep time L gt The sleeptimer can be up to 180 minutes in steps of five minutes If set to zero minutes the sleeptimer is switched off 4 Press OK to activate the sleeptimer L gt The TV switches to standby after the pre defined period of time Automatically switch the TV on on ti
11. ck of the TV Warning Follow all instructions provided with the TV mount Koninklijke Philips Electronics N V bears no responsibility for improper TV mounting that results in accident injury or damage TV VESA compatible wall screen bracket type size 32 37 200 x 200 mm M6 42 47 400 x 400 mm M6 42 M8 47 22 EN 9 Troubleshooting This section describes commonly encountered issues and accompanying solutions General TV issues The TV does not switch on e Disconnect the power cable from the power outlet Wait for one minute then reconnect it e Check that the power cable is securely connected The remote control is not working properly e Check that the remote control batteries are correctly inserted according to the orientation e Replace the remote control batteries if they are flat or weak e Clean the remote control and TV sensor lens The standby light on the TV blinks red e Disconnect the power cable from the power outlet Wait until the T V cools down before reconnecting the power cable If the blinking reoccurs contact Philips Consumer Care You forgot the code to unlock the child lock feature e Enter 0711 The TV menu is in the wrong language e Change the TV menu to your preferred language When turning the TV on off to standby you hear a creaking sound from the TV chassis e No action is required The creaking sound is normal expansion and contraction of
12. ct Features gt Clock Ls The Clock menu appears 1 Press AV or Numeric buttons to enter time 2 Press Done to confirm 3 Press MENU to exit Note The clock is disabled automatically after three seconds Update the TV software Philips continuously tries to improve its products and we recommend that you update the TV software when updates are available Check www philips com support for availability Check the current software version 1 Press MENU 2 Select Software update gt Current software Download the software 1 on your PC open a web browser and go to www philips com support 2 Find information and software related to your TV and download the latest software upgrade file to your PC Decompress the ZIP file A GJ Copy the autorun upg file to the root directory of the USB device Update software analog broadcasts Before performing this procedure be sure to e Set aside some time to complete the entire update Have available a USB storage device with at least 64MB of storage space Have access to a computer with a USB port and internet access Press MENU Select Software update gt Update assistant Select Start Connect the USB storage device to your computer UI AW N Follow the on screen instructions to complete the update Change TV preferences The Preferences menu allows you to customize various features and funct
13. ght To prevent the spread of fire keep candles or other flames away from the T V remote control and batteries at all times e Never insert objects into the ventilation slots or other openings on the TV e When the TV is swiveled ensure that no strain is exerted on the power cord Strain on the power cord can loosen connections and cause arcing Risk of short circuit or fire e Never expose the remote control or batteries to rain water or excessive heat e Avoid force coming onto power plugs Loose power plugs can cause arcing or fire Risk of injury or damage to the T V e Two people are required to lift and carry a TV that weighs more than 25 kg e When stand mounting the TV use only the supplied stand Secure the stand to the TV tightly Place the TV on a flat level surface that can support the combined weight of the TV and the stand e When wall mounting the TV use only a wall mount that can support the weight of the TV Secure the wall mount to a wall that can support the combined weight of the TV and wall mount Koninklijke Philips Electronics N V bears no responsibility for improper wall mounting that results in accident injury or damage Risk of injury to children Follow these precautions to prevent the TV from toppling over and causing injury to children e Never place the TV on a surface covered by a cloth or other material that can be pulled away e Ensure that no part of the TV ha
14. he menus G INFO Displays program information if available iK Mute Mutes or restores audio output CH CHANNEL Switches to the next or previous channel When the TV menu is on this functions as Page Up Down 0 9 Numeric buttons Selects a channel or setting C PICTURE Smart picture Launches the smart picture menu 2 SOUND Smart Sound Launches the smart sound menu EN 5 amp amp A Volume Increases or decreases volume BACKA CH e Returns to a previous screen e Returns to the previously viewed channel BROWSE Switches between channel grid and program list CC Displays closed captions settings TV PC Toggles between PC mode and previously viewed video mode SLEEP Sets a delay after which the TV switches to standby ED FORMAT Toggles through available picture formats Some formats are not available for some picture sources DEMO Toggles the demonstration menu on or off 4 Use your product This section helps you perform basic operations Switch your TV on off or to standby To switch on e Ifthe standby indicator is off press POWER at the side of the TV e If the standby indicator is red press Standby On on the remote control To switch to standby e Press Standby On on the remote control tL The standby indicator switches to red To switch off e P
15. hoice appears whenever the channel is selected 1 When watching TV press OK to display the channel grid 2 Select the channel you want to rename 3 Press OPTIONS Ly The channel options menu appears 4 Press AV to select Rename chan and press OK L gt A text input box appears 5 Press AV to select a character and press gt to add another character 6 Select Done 7 Press OK Rearrange channels After you install channels you can rearrange the order in which they appear 1 NA OO ND uU KRW When watching TV press OK to display the channel grid Press OPTIONS tL The channel options menu appears Press AY to select and enter Reorder Select the channel you want to reorder and press OK Press AY4b to select the new position for the channel Press OK to confirm the new position Press OPTIONS Done reordering appears Press OK to finish reordering EN 17 English 7 Connect devices This section describes how to connect various devices with different connectors and supplements examples provided in the Quick Start Note Different types of connectors may be used to connect a device to your TV depending on availability and your needs Back connectors VGA PC PC AUDIO IN De BQ TV ANTENNA 1 HDMI Digital audio and video input from high definition digital devices such as Blu ray players VGA PC and PC AUDIO IN Audio and
16. ing the TV to the power outlet Screen care e Avoid stationary images as much as possible Stationary images are images that remain on screen for extended periods of time Examples include on screen menus black bars and time displays If you must use stationary images reduce screen contrast and brightness to avoid screen damage e Unplug the TV before cleaning e Clean the TV and frame with a soft damp cloth Never use substances such as alcohol chemicals or household cleaners on the TV e Risk of damage to the TV screen Never touch push rub or strike the screen with any object e To avoid deformations and color fading wipe off water drops as soon as possible Recycling Your product is designed and manufactured with high quality materials and components which can be recycled and reused When you see the crossed out wheel bin symbol attached to a product it means the product is covered by the European Directive 2002 96 EC Never dispose of your product with other household waste Please inform yourself about the local rules on the separate collection of electrical and electronic products The correct disposal of your old product helps prevent potentially negative consequences on the environment and human health Your product contains batteries covered by the European Directive 2006 66 EC which cannot be disposed of with normal household waste Please inform yourself about the local rules on
17. ions 1 Press MENU 2 Select Installation gt Preferences 3 Press to enter Preferences e Location Optimizes TV settings for your location home or shop e Volume bar Displays the volume bar when adjusting the volume e EasyLink Enables one touch play and one touch standby between EasyLink compliant devices e _ E sticker For shop mode only Sets the location of the e sticker Press amp lt 4P to select your preference Press OK Press MENU to exit ON C1 A Start a TV demo You can use demonstrations to better understand the features of your TV Some demos are not available on certain models When a demo is available it is displayed in the menu list iia 1 Press DEMO on the remote control 2 Press AY to select a demo and press OK to view it 3 Press DEMO to exit Reset the TV to factory settings You can restore the default picture and sound settings of your TV Channel installation settings remain the same 1 Press MENU 2 Select Installation gt Factory settings 3 Press to enter the Factory settings menu Ly Reset is highlighted 4 Press OK to reset to factory settings D Press MENU to exit EN 15 English 6 Install channels The first time you setup your TV you are prompted to select a menu language and to install TV and digital radio channels if available This chapter provides instructions on how to reinstall and fine tune chan
18. mation Product information is subject to change without notice For detailed product information go to www philips com support Supported display resolutions Computer formats HDMI Resolution Refresh rate Hz 640x480 60 72 75 85 800x600 60 72 75 85 1024x 68 60 70 75 85 1280x 68 60 1280x1024 60 1360x 68 60 VGA Resolution Refresh rate Hz 640x480 60 72 75 85 800x600 60 72 75 85 1024x 68 60 70 75 85 1280x 68 60 1280x1024 60 1360x 68 60 Video formats Resolution Refresh rate Hz 720 x 480p 60 720 x 480i 60 720 x 5 6p 50 720 x 5761 50 1280 x 720p 60 1280 x 720p 50 1920 x 1080 50 60 1920x 1080p 24 25 30 50 60 Tuner Reception Transmission e Antenna input 5ohm coaxial IEC75 e TV system NTSC PAL M PAL N e Video playback NTSC SECAM PAL Remote control e Batteries 2 x AAA R03 type Connections e Headphone out stereo mini jack e TV antenna e CVBSin e CVBS out e YPbPr Component video CVI in e VGA In HDMI e VGA Audio in e USB for software update only Service connector Power e Mains power AC 110 240 50 60Hz e Standby power lt 0 3W e Ambient temperature 5 to 35 degrees Celsius EN 21 English Supported TV mounts To mount the TV purchase a Philips TV mount or a VESA compatible TV mount To prevent damage to cables and connectors be sure to leave a clearance of at least 5 5 cm from the ba
19. mer You can switch the TV to a specified channel at a specified time from standby 1 Press MENU 2 Select Features gt On timer Press gt to enter the On timer menu Press AY 4b to select Activate and set a day of the week or frequency Press OK to confirm Press AY 4b to select Time and set the starting time Press Done to confirm OO N ON Ui A LW Press AY4b to select Program no and set the channel 9 Press OK to confirm 10 Press MENU to exit El Select Off to switch off On timer When On timer is switched off only Activate option is available Setthe TV clock before you activate On timer feature see Set the TV clock on page 14 Use child control You can prevent your children from watching certain programs or certain channels by locking the TV controls Set or change your PIN code 1 Press MENU Press AY 4b to select Features gt Set code Press to enter the code setup 2 3 4 Enter your code with the Numeric buttons 5 Re enter the same code in the new dialog box for confirmation L gt Ifthe code is set successfully the dialog box will disappear However if the code cannot be set you will be prompted to re enter the code 6 if you want to change the code select Features gt Change code EN 13 English 7 Enter your current code using the Numeric buttons L gt If the code is validated you will
20. mple when switching channels When enabled this produces a more consistent audio volume e Delta volume Levels out volume differences between channels or connected devices Switch to the connected device before you change the delta volume Create and use lists of favorite channels You can create lists of your preferred TV channels and radio stations so that you can find those channels easily Tip You can create and store up to four favorite lists on your TV Select a favorite list BROWSE ronds NO TAN 1 When watching TV press OK to display the channel grid 2 Press OPTIONS tL The channel options menu appears 3 Press OK to select Show favorite ch L The favorite lists appear Press AV to select a favorite list Press OK t gt Only channels in the favorite list appear in the channel grid Un A Add a channel to a favorite list Tip View all channels before adding a channel to a favorite list 1 when watching TV switch to the channel you want to add to a favorite list see Switch channels on page 7 2 Press Av to select a channel to add to a favorite list Press OPTIONS Ly The channel options menu appears QI Press AY to select Mark as favorite Press OK L The favorite lists appear Press AV to select a favorite list to add the channel to Press OK Ls The channel is added to the favorite list N O AAA
21. nels Automatically install channels This section describes how to search and store channels automatically 1 Press MENU Select Installation gt Channel install gt Channel assistant 2 3 Press OK 4 Follow the on screen instructions to install channels Manually install channels This section describes how to search and store analog TV channels manually Step 1 Select your system Note Skip this step if your system settings are correct 1 Press MENU 2 Select Installation gt Channel install gt Analog Manual L gt The Analog Manual menu appears 3 Press AVP to select and enter Color system Press OK to confirm Un A Press AY 4b to select and enter Sound system 16 EN 6 Press OK to confirm 7 Press MENU to exit Step 2 Search and store new TV channels 1 Press MENU 2 Select Installation gt Channel install gt Analog Manual L gt The Analog Manual menu appears Press AY 4b to select and enter Search Press AY or use Numeric buttons to manually enter the three digit frequency Press OK to begin search Press 4 when the new channel is found N O UI A LW Press AY 4b to select Store new channel to store the new channel under a new channel number Press lt P to select Yes and press OK to store new channel 9 Press MENU to exit oo Rename channels Channels can be renamed so that a name of your c
22. nets design Do not compromise these design standards by applying excessive pull force to the front or top of the cabinet which could ultimately overturn the product Also do not endanger yourself or children by placing electronic equipment toys on the top of the cabinet Such items could unsuspectingly fall from the top of the set and cause product damage and or personal injury 18 Wall or Ceiling Mounting The appliance should be mounted to a wall or ceiling only as recommended by the manufacturer 19 Power Lines An outdoor antenna should be located away from power lines 20 Outdoor Antenna Grounding If an outside antenna is connected to the receiver be sure the antenna system is grounded so as to provide some protection against voltage surges and built up static charges Section 810 of the National Electric Code ANSI NFPA No 70 1984 provides information with respect to proper grounding of the mats and supporting structure grounding of the lead in wire to an antenna discharge unit size of grounding connectors location of antenna discharge unit connection to grounding electrodes and requirements for the grounding electrode See Figure below 21 Objects and Liquid Entry Care should be taken so that objects do not fall and liquids are not spilled into the enclosure through openings a Warning To reduce the risk of fire or electric shock this apparatus should not be exposed to rain or moisture and objects filled with
23. ngs over the edge of the surface e Never place the TV on tall furniture such as a bookcase without anchoring both the furniture and TV to the wall or a suitable support e Educate children about the dangers of climbing on furniture to reach the TV Risk of overheating Never install the TV in a confined space Always leave a space of at least 10 cm around the TV for ventilation Ensure curtains or other objects never cover the ventilation slots on the T V Risk of damage to the TV Before you connect the TV to the power outlet ensure that the power voltage matches the value printed on the back of the TV Never connect the TV to the power outlet if the voltage is different EN 3 English e Risk of injury fire or power cord damage Never place the TV or any objects on the power cord e To easily disconnect the TV power cord from the power outlet ensure that you have full access to the power cord at all times e When you disconnect the power cord always pull the plug never the cable e Disconnect the TV from the power outlet and antenna before lightning storms During lightning storms never touch any part of the TV power cord or antenna cable e Risk of hearing damage Avoid using earphones or headphones at high volumes or for prolonged periods of time e Ifthe TV is transported in temperatures below 5 C unpack the TV and wait until the T V temperature matches room temperature before connect
24. nstall channels 16 Automatically install channels 16 Manually install channels 16 Rename channels 16 Rearrange channels 17 7 Connect devices 18 Back connectors 18 Side connectors 18 Connect a computer 19 Use Philips EasyLink 20 Use a Kensington lock 20 8 Product information 21 Supported display resolutions 21 Tuner Reception Transmission Remote control Connections Power Supported TV mounts 9 Troubleshooting General TV issues TV channel issues Picture issues Sound issues HDMI connection issues Computer connection issues Contact us 10 Index EN 21 21 21 21 22 English 1 Notice 2009 Koninklijke Philips Electronics N V All rights reserved Specifications are subject to change without notice Trademarks are the property of Koninklijke Philips Electronics N V or their respective owners Philips reserves the right to change products at any time without being obliged to adjust earlier supplies accordingly The material in this manual is believed adequate for the intended use of the system If the product or its individual modules or procedures are used for purposes other than those specified herein confirmation of their validity and suitability must be obtained Philips warrants that the material itself does not infringe any United States patents No further warranty Is expressed or implied Philips cannot be held responsible neither for any errors in the content of this document nor for any problem
25. ress POWER at the side of the TV L The standby indicator switches off Tip Though your TV consumes very little power when in standby energy continues to be consumed When not in use for an extended period of time disconnect the TV power cable from the power outlet Note f you cannot locate your remote control and want to switch on the TV from standby press P CH at the side of the TV Switch channels POEL Press 9 BACK A CH on the remote control to return to the previously viewed channel e Press CH on the remote control or P CH on the side of the T V e Press OK to use the channel matrix e Enter a channel number using the Numeric buttons Note When you use a favorite list you can only select those channels in the list see Select a favorite list on page 12 EN 7 English Watch connected devices Use the source button Ga FORMAT INCR SURF SOURCE S 1 Press 9 SOURCE L gt The source list appears 2 Press A or Y to select the connected device 3 Press OK to watch the connected device Adjust TV volume SOURCE ae To increase or decrease volume e Press 4 e Press VOLUME on the side of the TV To mute or unmute sound e Press X to mute the sound e Press X again to restore the sound 5 Use more of your
26. s as a result of the content in this document Errors reported to Philips will be adapted and published on the Philips support website as soon as possible Pixel characteristics This LCD product has a high number of color pixels Although it has effective pixels of 99 99976 or more black dots or bright points of light red green or blue may appear constantly on the screen This is a structural property of the display within common industry standards and is not a malfunction Warranty No components are user serviceable Do not open or remove covers to the inside of the product Repairs may only be done by Philips Service Centres and official repair shops Failure to do so shall void any warranty stated or implied Any operation expressly prohibited in this manual any adjustments or assembly procedures not recommended or authorised in this manual shall void the warranty Compliance with EMF Koninklijke Philips Electronics N V manufactures and sells many products targeted at consumers which like any electronic apparatus In general have the ability to emit and receive electromagnetic signals One of Philips leading Business Principles is to take all necessary health and safety measures for our products to comply with all applicable legal requirements and to stay well within the EMF standards applicable at the time of producing the products Philips is committed to develop produce and market products that ca
27. s not fit the screen it is too big or too small e ry using a different picture format The picture position is incorrect e Picture signals from some devices may not fit the screen correctly Check the signal output of the device Sound issues There is picture but no sound from the TV Note f no audio signal is detected the TV automatically switches the audio output off this does not indicate malfunction e Check that all cables are properly connected e Check that the volume is not set to 0 e Check that the sound is not muted There is picture but sound quality is poor e Check that the sound settings are correctly set There is picture but sound comes from one speaker only e Verify that sound balance is set to the center HDMI connection issues There are problems with HDMI devices e Note that HDCP support can delay the time taken for a TV to display content from a HDMI device e Ifthe TV does not recognize the HDMI device and no picture is displayed try switching the source from one device to another and back again e If there are intermittent sound disruptions check that output settings from the HDMI device are correct e faHDMI to DVI adaptor or HDMI to DVI cable is used check that an additional 24 EN audio cable is connected to AUDIO L R or AUDIO IN mini jack only Computer connection issues The computer display on the TV is not stable e Check
28. separate collection of batteries The correct disposal of batteries helps prevent potentially negative consequences on the environment and human health 3 Your product Remote control Congratulations on your purchase and welcome to Philips To fully benefit from the support that Philips offers register your product at www philips com welcome Side controls and indicators 3 5 A POWER Switches the TV on or off The TV is not powered off completely unless it is physically unplugged Q P CH Switches to the next or previous channel G SOURCE Selects connected devices 4 VOLUME Increases or decreases Meet er volume PHILIPS TELEVISION EN English Standby On e Switches the TV to standby if the TV is on e Switches the TV on if the TV is in standby MENU Toggles the main menu on or off t INCR SURR Enables Incredible Surround for stereo sources Enables spatial mode for mono sources SOURCE Selects connected devices SAP Secondary audio program Selects Secondary Audio Program SAP Stereo Mono when SAP and or Stereo is broadcast OPTIONS Accesses options relating to the current activity or selection OK Confirms an entry or selection and displays the channel grid when watching TV AY4b Navigation buttons Navigates through t
29. solution of details in bright colors You can switch this feature on or off e PC mode Adjusts picture settings when a PC is connected to the TV e Picture format Changes the picture format e Horizontal shift Adjusts the picture horizontally for PC VGA or HD input e Vertical shift Adjusts the picture vertically for PC VGA or HD input 10 EN Change picture format m Ca C9 Emm oenen 1 FORMAT INCR SURR SOURCE 1 Press FORMAT L A picture format bar appears 2 Press AV to selecta picture format L gt The selected picture format is activated J Press OK to confirm your choice Summary of picture formats The following picture settings can be configured Note Depending on the format of the picture source some picture settings are not available Hi Super zoom Not for HD and PC mode Removes the black bars on the side of 4 3 broadcasts There is minimal distortion 4 3 Shows the classic 4 3 format Subtitle zoom Displays 4 3 pictures over the full area of the screen with sub titles visible Part of the top of the picture is clipped off Movie exp 14 9 Not for HD and PC mode Scales 4 3 format to 14 9 Movie exp 16 9 Not for HD and PC mode Scales 4 3 format to 16 9 Wide screen Stretches the classic 4 3 format to 16 9 Unscaled For HD and PC mode only and in selected models only Allows maximum sharpness Some dis
30. that a supported resolution and refresh rate is selected on the computer e Set the TV picture format to unscaled Contact us If you cannot resolve your problem refer to the FAQs for this TV at www philips com support If the problem remains unresolved contact Philips Consumer Care in your country as listed in this user manual Warning Do not attempt to repair the TV yourself This may cause severe injury irreparable damage to your TV or void your warranty Note Make a note of your T V model and serial number before you contact Philips These numbers are printed on the back of the TV and on the packaging 10 Index B Batteries 4 24 Bracket 22 C Channel list favorite 12 troubleshooting 23 update 12 Channels favorite list 12 install automatic 16 manual 16 rearrange 17 rename 16 Clock 14 Computer format technical specifications 21 Connections HDMI troubleshooting 24 mains cord 18 technical specifications 21 troubleshooting 24 D Demo 15 Display resolution 21 E EasyLink disable 20 enable 20 Environmental care 4 F Factory settings 15 Favorite list select 12 set up 12 H HDMI cable troubleshooting 24 Home mode 15 Installation automatic 16 manual 16 L Language troubleshooting 23 Location 15 M Menu language 23 main menu 9 troubleshooting 23 P Picture format troubleshooting 23 Picture settings 9 PIN code 23 Power 23 R Reception 23
31. the TV as it cools and warms up This does not impact performance TV channel issues Previously installed channels do not appear in the channel list e Check that the correct channel list is selected No digital channels were found during the installation e Check that the TV supports DVB T or DVB C in your country See the listed countries on the back of the TV Picture issues The TV is on but there is no picture e Check that the antenna is properly connected to the TV e Check that the correct device is selected as the TV source There is sound but no picture e Check that the picture settings are correctly set There is poor TV reception from an antenna connection e Check that the antenna is properly connected to the TV e Loud speakers unearthed audio devices neon lights high buildings and other large objects can influence reception quality If possible try to improve the reception quality by changing the antenna direction or moving devices away from the TV e f reception on only one channel is poor fine tune this channel There is poor picture quality from connected devices e Check that the devices are connected properly e Check that the picture settings are correctly set The TV did not save your picture settings e Check that the TV location is set to the home setting This mode offers you the flexibility to change and save settings EN 23 English The picture doe
32. tortion may be present due to the broadcaster s systems Set your PC resolution to LELU LEE wide screen mode for best results Use smart sound Use smart sound to apply pre defined sound settings H SOUND PICTURE mmm 1 Press SOUND L gt The Smart sound menu appears 2 Press AV to select one of the following smart sound settings e Standard Adjusts sound settings to suit most environments and types of audio e News Applies sound settings ideally suited for spoken audio such as the news e Movie Applies sound settings ideally suited for movies e Personal Applies the settings that were customized in the sound menu J Press OK to confirm your choice L gt The selected smart sound setting is applied Adjust sound settings 1 Press MENU 2 Press AV to select Sound L gt The Sound menu appears 3 Press Av to select and adjust Smart sound Accesses pre defined smart sound settings e Bass Adjusts the bass level e Treble Adjusts the treble level e Volume Adjusts the volume e Balance Adjusts the balance of the right and left speakers to best suit your listening position e Stereo Mono SAP Selects between audio languages if dual sound is broadcast EN 11 English e Mono Stereo Selects between mono or stereo if stereo is broadcast e Surround Enables spatial sound e Auto volume Automatically reduces sudden volume changes for exa
33. use no adverse health effects Philips confirms that if its products are handled properly for their intended use they are safe to use according to scientific evidence available today Philips plays an active role in the development of international EMF and safety standards enabling Philips to anticipate further developments in standardisation for early integration in its products Copyright All other registered and unregistered trademarks are the property of their respective owners Kensington and Micro Saver are registered US trademarks of ACCO World corporation with issued registrations and pending applications in other countries throughout the world VESA FDMI and the VESA Mounting Compliant logo are trademarks of the Video Electronics Standards Association Portions of this software are copyright The Free Type Project www freetype org Important Read and understand all instructions before you use your TV If damage is caused by failure to follow instructions the warranty does not apply Safety Risk of electric shock or fire e Never expose the TV to rain or water Never place liquid containers such as vases near the T V If liquids are spilt on or into the TV disconnect the TV from the power outlet immediately Contact Philips Consumer Care to have the TV checked before use e Never place the T V remote control or batteries near naked flames or other heat sources including direct sunli
Download Pdf Manuals
Related Search