Philips 32HF7543 Flat Panel Television User Manual
Contents
1. No Setting PSIP to Yes means that the PSIP Virtual Channel Tables will be processed and used when tuning digital signals Setting PSIP to No means PSIP Virtual Channel Tables will not be processed and digital channels will be tuned using the RF channel location and MPEG program number as defined in PAT PMT 2005 Series User s Manual 112505 0959 CHANNEL INSTALL gt The CHANNEL INSTALL menu allows the user to configure the channels that can be accessed When installing the channels different inputs can be mapped to channels to allow seamless integration into the channel map The two sections below explain how to install analog channels and AV inputs and how to install digital channels Installing Analog channels When selected CHANNEL INSTALL menu appears as follows Configure the inputs and channels as described CHANNEL INSTALL CHANNEL Select the channel you wish to configure SOURCE Select the input source that you wish to associate with the specified CHANNEL This feature enables you to map re assign a numeric channel number to a video input rather than to its normal RF TV channel 1 0 ANALOG In other words TV channel 2 could be used to select the AV 1 video input instead of RF ANALOG channel 2 Special instructions for mapping digital channels are included below e RING Specify whether the current channel or input 15 to be SAVED to or DELETED from the channel ring 1 list of channels a2. the TV was tuned at last power down If specified e g 2 AVI etc then that will always be the channel input at power on until SWITCH ON CHANNEL is changed SWITCH ON VOLUME STANDARD 0 99 Specify the volume setting that takes effect when the TV is powered on If STANDARD the volume at power on will be the volume at which the TV was prior to last power down If specified as 0 99 that will always be the volume at power on until SWITCH ON VOLUME is changed POWER ON STANDBY FORCED ON STANDBY The TV will be in standby mode when AC mains power 15 first applied after having been disconnected FORCED ON The TV will turn ON whenever AC mains power is applied This feature allows the TV s power status to be controlled for example from an AC mains breaker In addition the set cannot be put into standby with a guest remote or using the front panel power key e VOLUME INDICATOR NO YES When VOLUME INDICATOR is set to YES an OSD graphic appears that provides visual verification e g VOLUME 15 during volume adjustment by means of either the remote control or the front panel if it is not locked out e CHANNEL DISPLAY NONE NUMBER LABEL ALL Specifies which of the respective channel properties are displayed by the TV s OSD when a channel or input is first selected e 3 DIGIT ENTRY NO YES o YES The TV upon receiving a remote control digit command expects to receive up to two more successiv
3. 2005 Series User s Manual 112505 0959 32HF7543 37 7543 42 7543 User s Manual PHILIPS 2005 Series User s Manual 112505 0959 SAFETY INFORMATION Disconnect mains plug when gt the red light below the TV screen is flashing continuously gt abright white line is displayed across the screen gt cleaning the TV screen Never use abrasive cleaning agents Use a slightly damp chamois leather or soft cloth gt there is a lightning storm gt the set is left unattended for a prolonged period of time No open flame sources such as lighted candles should be placed on or near the TV Do not place your TV set under direct sunlight or heat Leave at least 1 4 around each side of set for sufficient ventilation to avoid over heating Avoid placing set where it is likely to be exposed to rain or water e g near the window No objects filled with liquids should be placed top the order to avoid dripping or splashing of liquids into the set USEFUL TIPS Do not leave the television off in standby mode for a prolonged period of time Do not re position the television while it is switched on Nom uniformity in screen color may result Never attempt to repair a defective TV yourself Always consult skilled service personnel 2005 Series User s Manual 112505 0959 Before Calling Service A list of common symptoms is presented as follows Before you call for service perfor
4. 73GR setup remote control TV Setup Menu and Sub Menus LANGUAGE English Espanol Francais When you first enter the TV SETUP menu LANGUAGE is highlighted You can scroll to the LANGUAGE item Select the desired language with cursor left or cursor right COMMUNICATION COMMUNICATION COMMERCIAL MODE COMMERCIAL MODE is normally YES during typical operation in BDS Television applications When Commercial Mode is NO the television s Hotel Mode Menu may be accessed The user sends the sequence 3 1 9 7 5 3 MUTE to invoke the hotel mode sub menu 2005 Series User s Manual 112505 0959 The specific steps for entering Hotel Mode Menu setting Hotel Mode to No making changes to the consumer set and then reversing the process are as follows Using RC2573GR setup remote enter setup menu Go to Communication item and right arrow to select Set Commercial Mode to No Exit setup menu press twice Press sequence 3 1 9 7 5 3 mute to enter Hotel Mode Menu Set Hotel Mode to No Scroll down to Store press right arrow to go to Store on the right side of screen Press F button to get Store Completed Remove AC power from set for at least 5 seconds 9 Power on set Set is now in consumer mode and changes can be made to the non commercial settings 10 When finished with consumer settings press sequence 3 1 9 7 5 3 mute to enter Hotel Mode Menu 11 Set Hotel Mode to yes scroll down and ensu
5. Mode Menu This item indicates the RF channel number if PSIP is set to NO e MINOR This item indicates the Minor channel of two part ATSC channel number if PSIP is YES in the Hotel Mode Menu This item indicates the Program number as defined by PMT if PSIP is set to NO LABEL Input a maximum of 8 characters for the channel s label Cursor to the Right to start the first character Cursor left or right to navigate between character positions within the label field Cursor up or down to select characters from the list A to Z to 9 2 lt gt or space To edit re input the character at its position To exit press to navigate out of the label editing field 11 2005 Series User s Manual 112505 0959 SWITCH ON OSD SWITCH ON OSD WELCOME MESSAGE A welcome message two lines 20 characters can appear on screen when the set 15 powered on The message remains on screen until the TV receives a command from the remote or front panelor times out in 25 seconds When the WELCOME MESSAGE setup menu item is highlighted cursor right or left to invoke the MESSAGE sub menu Cursor up or down to select the desired MESSAGE sub menu item Press MENU to return to the SETUP main menu e SWITCH ON CHANNEL TV 1 125 HDMI 1 HDMI 2 SIDE AV AV 2 STANDARD Specify the channel input to which the TV will be tuned when it 1s powered on If STANDARD the channel at power on will be that to which
6. Optional 2005 Series User s Manual 112505 0959 A Guest Remote may be used to access a limited menu and to perform the basic control functions of the television Remote control RC2573GR 15 an optional remote control specifically for configuring Institutional TV Business Display Solutions features and SmartCard settings Refer to the documentation for the RC2573GR for detailed information Remote controls are optional accessories for all HF series products and must be purchased separately When the RC2573GR in is setup mode and RECALL is pressed information similar to below will appear on the TV screen This information describes the TV chassis firmware version diagnostic codes setup information and other service and technical data regarding the television configuration Line 1 shows the SmartPort Processor part number Line 2 shows the software version number Line 5 shows the model number of the set no distinction is made on screen size Lines 3 4 6 are blank Line 7 shows the communication mode always SP SPI for these models and the status of the SmartPort either online or offline Line 8 shows the source or channel that has been selected and if a signal 1s detected on that source Tuned or Not Tuned Below is an example screen 01 3104 337 01381 02 IJ5UI 1 0 05 MODEL xxHF7543 37 07 COMMUNICATION SP SPI ONLINE 08 TV 3 TUNED 2005 Series User s Manual 112505 0959 CH Guide GUEST REMOTE CONTROL KEYS To activ
7. ailable on analog channels 16 2005 Series User s Manual 112505 0959 32 7543 Rear and Side Jack Panel Connections swa DATA i UR DUM or 1 sag j EDET i sea Cable CARD INTERFACE ANTENNA 17 2005 Series User s Manual 112505 0959 37 42HF7543 Rear Jack Panel Connections VGA PC via RGB VH S VIDEO 37 42HF7543 Bottom Jack Panel Connections MAINS Cable CARD INTERFACE HDMI ANTENNA DATA 1 i 1 HIHHHHHHHIHIE 751 l o i EX m t L 18
8. ate Channel Source Select Standby To toggle between Press to s witch available video sources the TV off DVD PAUSE DVD PLAY To Pause DVD playback To Start DVD playback if applicable if annlicahle DVD Rewind Rewind DVD playbac Close Caption if applicable To activate Close Caption functionality DVD FAST FORWARD DVD STOP To Fast Forward DVD To Stop DVD playback if applicable playback if applicable Smart Keys To select predefined picture Menu and sound settings To call up or exit the menus Sleep Activates the sleep timer Press repeatedly to Vol increment the countdown To adjust the volume time with 15 minutes Interrupt the sound or a restore 1f 5 CH Channel Selection To move up or down a TV To select a TV channel ACH FORMAT For a two digit program number enter the second 0 C digit before the dash appears Alternate Channg PHILIPS Formats To toggle between To adjust TV alternating channels screen formats 2005 Series User s Manual 112505 0959 TV Setup Main Menu SETUP e To enter press on the RC2573GR setup remote control To scroll through the menu press tanet cursor up down on the remote control A highlight indicates that the respective menu item s setting is selected for modification e To modify the setting of the selected menu item press 4 71 ce gt cursor left right e To exit press M on RC25
9. connections and antenna cable e Possible electrical interference from appliances or other sources Double images ghost images Television does not respond to remote control e Check batteries e Aim remote control handset directly at remote control sensor lens on the TV Channel Change to digital channels is slow The first time a digital channel is tuned the tuning time will be slow as information embedded in the signal is processed After that digital channel tuning will be faster Note These televisions are shipped in commercial mode with the processing of PSIP Virtual Channel Table VCT disabled To enable PSIP VCT processing see the Hotel Mode Menu section 2005 Series User s Manual 112505 0959 Basic Television Connection 117 VAG 60 HZ I Ba Di Ti JAM me le bul ars Cal A A r s vl a 5 Kk r m gh a i ie iw a m ct 2005 Series User s Manual 112505 0959 Use And Care of Remote Control REMOTE CONTROLS The following remote controls are applicable to the Philips HF series television products These can be used for guest control functions and setup and configuration purposes 1 e lt ae a gt Oo p 0060 f0 0 0 e D RC2888 01 RC2573GR Guest Remote Setup Remote
10. e remote control digit commands e g 123 012 etc before tuning the intended channel The television will display in 12 2005 Series User s Manual 112505 0959 the upper left hand corner of the screen each digit as it is received followed by a hyphen indicating that the TV is waiting for the next digit see Note NO The TV upon receiving a remote control digit command expects to receive one more successive remote control digit command before tuning the intended channel see Note Note Successive digit commands must occur within two seconds or the TV will interpret the previously received digit s as constituting the intended channel and tune accordingly e SWITCH ON PIC FMT AUTO 4 3 ZOOM 14 9 ZOOM 16 9 SUBTITLE ZOOM WIDESCREEN SUPERZOOM Set the default screen format of the television at Power On The pictures you receive may be transmitted in 16 9 format wide screen or 4 3 format conventional screen 16 9 pictures sometimes have a black band at the top and bottom of the screen letterbox format This function allows you to optimize the picture display on screen 13 2005 Series User s Manual 112505 0959 Using the different formats Select the preferred format from the SWITCH ON PIC FMT menu item in the setup screen or if applicable use the Format button on the Remote Control to select the different modes 4 3 Zoom 14 9 Zoom 16 9 Subtitle zoom Super Zoom a
11. m these simple checks Some of these symptoms can be readily corrected Note Please become familiar with the commercial features as described in Installation Setup because the effects of several of these features if they are not thoroughly understood might appear as faulty operation Symptom Possible Corrective Action TV does not respond to commands volume Check commercial TV setup TV installation channel power or cannot be turned on if it is off setup menu settings including power forced on or cannot be turned off if it 15 on front keypad lockout channel ring volume maximum features TV turns off by itself e TV automatically turns off after when no RF signal is present e Check Energy Saving Programmability setting see ESP in TV installation setup Verify that the TV s AC power cord is plugged into the mains socket If there 1s still no power disconnect plug Wait for 60 seconds and re insert plug Switch on the TV again No picture Check antenna connection at rear of the TV Possible TV station problem Try another channel Picture ok no sound Try increasing the volume Check that the sound is not muted If it is muted press the Mute button on the remote control to restore sound Check the MAX VOLUME settings in the setup menu Sound ok but poor color or no picture Check picture adjustments brightness contrast color tint Snowy noisy picture e Check antenna cable and or set top box
12. nd Widescreen 4 3 The picture is reproduced in 4 3 format and a black band is displayed on either side of the picture Zoom 14 9 The picture is enlarged to 14 9 format a thin black band remains on both sides of the picture Zoom 16 9 The picture is enlarged to 16 9 format This mode is recommended when displaying pictures that have black bands at the top and bottom letterbox format Subtitle Zoom This mode is used to display 4 3 pictures using the full surface of the screen leaving the subtitles visible Super Zoom This mode is used to display 4 3 pictures using the full surface of the screen by enlarging the sides of the picture Widescreen This mode restores the correct proportions of pictures transmitted in 16 9 using the full screen display 14 2005 Series User s Manual 112505 0959 SECURITY e SECURITY STANDARD HIGH Special feature for commercial use only KEYBOARD LOCK NO YES NO The TV s keyboard is operational YES The TV s keyboard 15 disabled CONTROL CONTROL e ESP OFF 1 HR 2 99 HR Energy Saving Programmability This feature enables the TV to automatically power down after a specified period of time if during any such period it receives no commands from the front panel or remote control This is an energy saving feature that assumes that the TV after the specified period of inactivity is no longer being viewed SOURCE MENU ITEM NO YES This feature
13. provides the option to display or delete the source option from the guest menu PIC FMT MENU ITEM NO YES This feature provides the option to display or delete the picture format option from the guest menu CHANNEL GUIDE NO YES The channel guide feature provides an or screen summary listing of the RF tuner channels that are currently in the channel ring see CHANNEL INSTALL gt CHANNEL RING and have been assigned labels see CHANNEL INSTALL gt LABEL MAX VOLUME 0 99 Specify the highest volume setting possible by means of either the remote control or the front panel if it is not locked out Note The MAX VOLUME setting is effective whether the volume command is issued from the front panel if it 1s not locked out a standard guest mode remote control or an RC2573GR setup remote in setup mode 2005 Series User s Manual 112505 0959 CLOSED CAPTION CLOSED CAPTION e SAVE CC If yes saves the state of the closed caption settings chosen in the guest menu when the TV is put into standby or powered off If no the settings are restored to their default condition when the is put into standby or powered off e CC Allows Closed captions to be enabled disabled or enabled only while the volume is muted e DIGITAL CC MODE The settings displayed represent the Closed Caption services available on digital channels e ANALOG CC MODE The settings displayed represent the Closed Caption services av
14. re PSIP is set to desired setting Scroll down to Store press right arrow to go to Store on the right side of screen Press F button to get Store Completed 12 Remove AC power from set for at least 5 seconds and then restore AC power to set Set is now back in Hotel mode 13 Wait about 10 seconds you will hear a click around that time then press power button on setup remote in setup mode 14 Wait a few seconds and press M to invoke menu 15 Go to Communication item and right arrow to select 16 Set Commercial Mode to Yes 17 Exit setup menu press M twice 18 Press power button on setup remote to turn set off and then turn back on to ensure settings are saved 19 Set should now work as a commercial set 2 ATSC digital terrestrial broadcast channels send information along with the television signal that is known as PSIP information PSIP information contains data such as the channel numbers that will normally be seen by the viewer of the channel These channels are virtual channels meaning the channel numbers displayed may not represent the channel numbers where the signals are physically located In normal viewing of ATSC signals by consumers these virtual channels are used when tuning However in some commercial applications there is a desire not to use virtual channels and instead use the physical channel numbers when tuning The Hotel Mode Menu allows the selection of PSIP to either Yes or
15. vailable for selection by means of a standard guest remote control LABEL Input a maximum of 8 characters for the channel s label Cursor to the right to start the first character Cursor left or right to navigate between character positions within the label field Cursor up or down to select characters from the list A to Z to 9 1 2 3 lt gt or space To edit re input the character at its position To exit press M to navigate out of the label editing field AUTOINSTALL When AUTO INSTALL is selected the performs an automatic search for the presence of viable RF analog signals at its tuner input Channels 1 through 125 will be checked When a viable signal is detected on a given channel that channel 1s added to the channel ring Any command from a remote control terminates the AUTO PROGRAM session 10 2005 Series User s Manual 112505 0959 Installing Digital Channels CHANNEL INSTALL CHANNEL Select the channel or input you wish to configure SOURCE When DIGITAL is selected two additional entries are added to the menu to allow for mapping the digital channels e RING Specify whether the current channel or input is to be SAVED to or DELETED from the channel ring 1 list of channels available for selection by means of a standard guest remote control e MAJOR This item indicates the Major channel of two part ATSC channel number if PSIP 15 YES the Hotel
Download Pdf Manuals
Related Search