Philips 26HF5443 Flat Panel Television User Manual
Contents
1. The TV goes to standby now and will start up automatically Your TV is now installed and ready for use 18 Problems and Solutions The message WRONG VERSION is displayed on the screen gt The program stored into the Wireless Smart Loader has a software code incompatible with the actual TV Reprogram the Wireless Smart Loader from a master TV whose software code is compatible with the actual TV 1 The message I2C ERROR is displayed on the screen gt Bad connection of RJ11 wire or wrong data transmission occurred Please check the RJ11 connection and try again 2 TV doesn t respond to the Wireless Smart Loader gt check if the LED on the Wireless Smart Loader is green when pressing any button and check if the batteries are in a good condition Replace batteries if necessary gt try to bring the Wireless Smart Loader more closer to the TV infra red receiver and try again Tips 1 Do not forget to write the software code and the type of relevant master TV on the sticker used on the back of the Wireless Smart Loader 2 In case of empty or no batteries available it remains possible to install TVs using the wired method of the Wireless Smart Loader 3 The Wireless Smart Loader can retain without batteries the stored information for ten years if required NOTE Before putting the Wireless Smart Loader into store for a long time make sure that the batteries are all taken out to prevent the b2. Left key to select the desired format Power On The Power On menu function defines the behavior of the television whenever AC Power is applied The available options are FORCED ON LAST STATUS STANDBY and ON O FORCED ON TV will be automatically switched to ON mode whenever the mains power is turned ON or resumed after a power interruption Note that the remote control STANDBY key will no longer function when TV is set in this mode TV can only be switched OFF by means of the main switch or a set up remote control or by ESP function Energy Saving Programmability controls the maximum continuous viewing time allowed LAST STATUS TV will be automatically switched to the last status either STANDBY or ON whenever the mains power is turned ON or resumed after a power interruption STANDBY TV will be automatically switched to STANDBY mode even if the last status was ON whenever the mains power is turned ON or resumed after a power interruption ON available only on TV with Iboard sw version ICAXA1_1 6 onwards Similar function as FORCED ON but the remote control STANDBY key function is enabled when TV is set to this mode Volume Indicator To display volume indicator when adjusting volume select YES Select NO to hide the volume indicator Channel Display Channel Display values can be Number Label All None Picture and Sound settings _ In this sub menu the Picture and Sound settings o
3. TY number followed by Up Down key Protection No Program number O or OO are not allowed Input The Input menu item selects the desired input source that will be assigned to the program Possible values are Tuner AV2 S Video Side AV Side S Video CVI 1 PC A PC D CVI 2 and HD D Note that some input sources may not be available on certain models System NTSC 3 58 BG I DK M NTSC 4 43 BG I DK PAL 4 43 BG I DK SECAM 4 43 BG I DK and AUTO Frequency Digits can be entered for a frequency in MHz Press the Right key to start the auto search during frequency entry the digits not yet entered are displayed as dashes Enter first digit as 0 for frequencies below 100 MHz Label This menu item will be used to add a label name for each program o Press the Left Right key to select the label digit press the Up Down key to insert alphanumeric characters Oo Press the Menu button to exit the Label menu item Store The Channel information is stored after pressing the Left Right key Press the Menu key to exit without storing Fine Tune Press the Left Right key for fine tuning Mute This item enables disables picture and sound for the particular channel o NONE normal picture and sound enabled o VIDEO picture is blanked for this channel e g radio channel o AUDIO sound is muted for this channel e g information channel Auto Install TV This sub menu allows the TV channels to be scanned and set aut
4. companies Please find out about local regulations on the disposal of your old television set Pay particular attention to the disposal of exhausted batteries Your television consumes energy in the stand by mode Energy consumption contributes to air and water pollution We advise you to switch off your television overnight instead of leaving it in stand by mode Preparation reparation Wall mounting instructions Table stand According to the type of TV you ve purchased a wall mount bracket and or stand may be supplied To mount the supplied stand and or wall mount bracket please refer to attached separate instructions Make sure that the wall mount is fixed securely so that it meets safety standards Make sure that air can circulate freely through the ventilation slots To prevent any unsafe situations no naked flame sources such as lighted candles should be placed on or in the vicinity Avoid heat direct sunlight and exposure to rain or water The equipment should not be exposed to dripping or splashing and no objects filled with liquids such as vases should be placed on it Insert the aerial plug firmly into the aerial socket at the bottom rear of the TV Connecting the Mains Insert the mains plug into the wall socket and switch on Please refer to the label on the back of the television fo the correct operating voltage Installing the remote control e Remove the cover at the back of the remote control e In
5. the maximum volume allowed for the television set Use Right Left key to adjust dida GuestMenultems Guest Menu Items u Menu Brightness S8 Colour 55 Contrast 65 Sharpness 50 Sleeptimer Off Picture Format Fullscreen Language English Brightness Colour Contrast Sharpness Use the remote control Right Left key to change the picture setting Sleeptimer This item is to select an automatic period for the TV to switch to Standby when the TV does not receive any commands from the user This is a useful feature for energy saving if hotel guests have left the room with the TV still in the On mode Available periods are 15 mins 30 mins 45 mins 60 mins 90 mins 120 mins 180 mins 240 mins and OFF Use the remote control Right Left key to select the required period Note Sleeptimer option is not available when Power On is set to the Forced On mode Picture Format Use the remote control Right Left key to select the desired picture format The following options are available 4 3 Zoom 14 9 Zoom 16 9 Subtitle zoom Widescreen Super Wide or Fullscreen Language option not available in 32HF7443 with earlier software version For selecting Guest Menu language English Chinese Malay 13 Alarm On for sets with Clock display Activates the wake up alarm After a valid time 0 00 to 23 59 is entered the Wake up Alarm icon on the clock display will be visible Pay TV To move up or down a Pay T
6. up down and RADIO up down are active in Setup menu mode and the television reacts the same way as in TV mode Setup menu items a Setup u Language English Communication gt No of Channels Channel Install Configuration Yow Y Language Select the language of the installation menu Options are ENGLISH MELAYU and CHINESE Note The Chinese Language is for the Guest Menu only Communication The Communication options SP SPI SP IC2 HM Link and Multi RC SP SPI SP I2C and HM Link are for enabling interactive applications Multt RC available only on TV with Iboard sw version IC4XA1_1 6 onwards is a feature to program the TV and RC for a one to one matching in a multi TV environment Multi RC allows up to four unique groups of TV RC matching For normal stand alone applications select OFF option under the Communication sub menu Multi RC Set up procedure 1 Press the RC Menu key together with one of the coloured keys Red Green Yellow Blue for at least 4 seconds 2 Access the TV Set Up Menu and select Multi RC option 3 Under Multi RC sub menu select the corresponding colour to match the colour selected in Step 1 Notes 1 SP SPI and SP IC2 refers to the Philips communication protocols that are used in conjunction with the Data 1 RJ12 or and Data 2 RJ45 connectivity to an external STB or Smart Card Xpress Box 2 HM Link is mainly used in conjunction with Data 1 RJ12 connecti
7. 26HF5443 32HF7443 Instruction for Use PHILIPS Care of the screen Do not touch push rub or strike the screen with anything hard as this may scratch or damage the screen permanently Do not rub with chemically treated cloth Do not touch the surface with bare hands or greasy cloth Unplug the TV before cleaning the screen When the surface becomes dusty please wipe gently with absorbent cotton or other soft materials like chamois Do not use acetone toluene and alcohol because they cause chemical damage Do not use liquid cleaners or aerosol cleaners Wipe off saliva or water drops from the screen as soon as possible as their long time contact with the screen may cause deformations and colour fading over time Warning concerning stationary images on the TV screen For Plasma TV only A characteristic of Plasma Display Panels is that displaying the same image for a long time can cause a permanent after image to remain on the screen This is called phosphor burn in Normal use of the Plasma TV should involve the showing of pictures that contain constantly moving and changing images that fill the screen Warning concerning VGA DVI display mode As this product processes in VGA DVI mode some diagonal lines may be seen due to environmental interference This will not affect the computer signal performance that displays in VGA DVI mode Environmental Your television contains material that can be recycled and reused by specialized
8. V channel Alarm Off for sets with Clock display Deactivates the wake up alarm The Wake up Alarm icon on the clock display will disappear Menu To call up or exit the TV menus Vol To adjust the volume Mute Press once to suppress the TV sound Press once more to restore the TV sound 0 9 Digit keys To select a TV channel For a two digit programme number enter the second digit before the dash appears PHILIPS TV Teletext See p 13 for details _14 Remote control keys Standby Press to switch the TV to standby mode Info To move up or down an Info channel Radio To move up or down a Radio channel Smart Keys To select predefined picture and sound settings I II To select 1 or 299 language Language availability depends on the transmission TV Channel Selection To move up or down a TV channel AV To select the desired source Loop through Tuner and all the available external source eg AV S Video CVI VGA HDMI and etc Teletext Teletext Teletext is an information system broadcast available in certain channels In some countries it also offers access to subtitles for viewers with hearing problems or who are not familiar with the transmission language cable networks satellite channels etc 9 Press ALARM a E if To switch Teletext On Off if PAY TY INFO RADIO 9 00 SAMLAR I SAE i In Teletext mo
9. Wireless Smart Loader Smart Loader The Philips Wireless Smart Loader 22AV1120 00 is an installation tool especially designed for easy and fast installation of Philips Institutional TV s Preparation Make sure that the 3 R6 AA sized batteries are placed correctly in the battery compartment of the Wireless Smart Loader Turn the power switch on at the left side of the product A green LED at the top casing should light up when pressing any button indicating operational batteries When the LED light is red it indicates that the batteries need to be replaced The installation procedure consists of three steps 1 Choosing the master TV 2 Programming the Wireless Smart Loader 3 Installing a TV with the Wireless Smart Loader gt Step 3 can be repeated on as many TV sets as required 1 Choosing a Master TV The master TV is the TV whose installation set up has to be copied into other T V s of the same type 2 Programming the Wireless Smart Loader This step has to be done only once or any time the program of the Wireless Smart Loader has to be changed Point the Wireless Smart Loader to the T V s infra red receiver distance around 5 to 30cm Press the MENU Key on the Wireless Smart Loader TV shows the following menu SMARTLOADER TO TV gt TV TO SMARTLOADER gt Highlight TV TO SMARTLOADER Press the right cursor key on the Wireless Smart Loader for wireless method or on the TV Remote Control for
10. atteries corroding the contacts D Wired Smart Loading works with CRT TVs only Wireless Smart Loading works with both Flat TVs and CRT TVs Low battery check battery check Press the key for approximately 5 seconds The following text then appears SERVICE 1 REMOTE BATTERY OK If the word LOW appears instead of OK the remote control batteries are low and must be replaced _19 CZD Should your remote be lost or broken you can still change some of the basic settings with the keys on top side of your TV Keys on top of TV Keys on side of TV Press The Volume key to adjust the volume The Program key to select the TV channels or source Press the MENU key to summon the main menu not available on all TVs Use The Program key to scroll up and down the menu to select item The Volume key to change the value of the selected item The MENU key once more to remove the menu 20 Connecting the television set This section provides information on the connectivity available for the respective TV models Refer to the screen size that is relevant to your TV set 32 26 LCD TV Mili PE D 0 0 S Video al o d amp x n TS 80 Connectors on the TV set External Bathroom Speaker Connector 3 Ohm 1 Watt Video Audio In Connector Side AV mini jack S Video In Connector Side S Video Data 2 RJ45 jack for interactive connec
11. de press MENU DR To enter a 3 digit page number lt gt For previous next page TY 4 For previous next page E no Direct access to coloured page numbers as indicated at the bottom of screen PHILIPS TV _15 16 9 Formats The pictures you recetve may be transmitted in 16 9 format wide screen or 4 3 format conventional screen 16 9 pictures sometimes have a black band at the top and bottom of the screen letterbox format This function allows you to optimize the picture display on screen Using the different formats The Picture Format can be set via the Guest Menu or Set Up Menu 4 3 The picture is reproduced in 4 3 format and a black band is displayed on either side of the picture Zoom 14 9 The picture is enlarged to 14 9 format a thin black band remains on both sides of the picture Zoom 16 9 The picture is enlarged to 16 9 format This mode is recommended when displaying pictures that have black bands at the top and bottom letterbox format Subtitle Zoom This mode is used to display 4 3 pictures using the full surface of the screen leaving the subtitles visible Super Wide This mode is used to display 4 3 pictures using the full surface of the screen by enlarging the sides of the picture Widescreen This mode restores the correct proportions of pictures transmitted in 16 9 using the full screen display 16 Fullscreen This mode displays images in full screen
12. f the TV can be selected Brightness This changes picture i Picture Sound brilliance Colour This changes the intensity Brightness of the colour Colour Contrast This changes the difference between the light and dark tones Sharpness This changes the Tint picture definition Active Control Tint This allows adjustment of Treble colour hue to obtain natural skin Bass tones Balance Active Control menu option AVL only available in certain models Active Control function optimises the quality of the picture according to the quality of reception Contrast Sharpness Treble Bass This adjusts the level of treble and bass effects on the TV s sound output Balance This balances the sound on the left and right speakers AVL Automatic Volume Leveller This option is used to limit the increase in sound level especially during programme change or advertising slots 10 Security settings In this sub menu the Security settings of the TV can be configured Security Security Level Standard Keyboard Lock No Video Out Mute No Security Level The SECURITY function allows the user to select one of two states HIGH or STANDARD The default is STANDARD Oo When the set is in the Security High Mode the setup menu can only be accessed by a Institutional Set up Remote Control Oo When the set is in the Security Standard Mode the Set up Menu can be accessed with a guest remote control by a seq
13. omatically Protection This function is to protect a selected program for Pay TV purpose Press the Left Right key to toggle the protection between YES and NO Switch On OSD In this sub menu the Switch On characteristics and On Screen Display settings of the TV upon switched On can be configured Switch OnfOSD di Picture Sound In this sub menu Picture Sound the Picture and Sound settings of Security w the TV can be set Security In this sub menu the CONO g SG of the TV can be configured Ne Control In this sub menu the Control settings of the TV can be configured Switch On OSD In this sub menu the behavior of the TV after switching on and the behavior of the On Screen Display can be selected A _ e Welcome Message Press Cursor mer N Left Right to display Welcome Switch On OSD N message entry menu o Welcome Message Welcome Message gt o Display Yes No Switch On Channel AVI o inel o Line 2 Switch On Yolume 20 GIA Switch On Pic Fmt Fullscreen With the Up Down key you can Power On Last Status set the message characters Switch On Channel This item Volume Indicator Yes sets the television s channel at Channel Display All switch on Ne sets the television s volume at switch on Use the Right Left key to adjust I Switch On Volume This item Switch On Pic Fmt This item sets the television s Picture Format at switch on Use the Right
14. sert the correct battery type and size into the compartment making sure that the polarity orientation is correct e You can secure your batteries by fastening an appropriate screw into the hole of the battery cover Switch the TV on Press the power switch O on the TV An indicator on the front of the TV lights up and the screen comes on If the TV is in standby mode red indicator press the TV keys or the key on the remote control to switch on the TV To use the menus use the menus Accessing the Set up Menu When the set is in the High Security Mode the Setup menu can be accessed only by the Institutional Set up Remote Control RG4172BK or RC2573 by pressing the M key The Institutional Set Up Remote Control is available as an option When the set is in the Standard Security Mode the Set up Menu may be accessed with the standard guest remote control RC2887 by a sequence of commands 3 19 75 3 MUTE a 90 O GEO PHILIPS STV RC2887 RG4172BK RC 2573 Optional Optional Navigation The current menu item can be selected by means of the Up Down keys Submenus can be accessed from menu items indicated with a gt symbol by pressing the Right key Language Communication No of Channels Channel Install Configuration To exit any menu press Menu button Selec YES to activate enable a setting NO to deactivate disable TELEVISION up down INFO up down PAY TV
15. tivity purposes Data 1 RJ12 jack for interactive connectivity purposes TV aerial socket CVI 1 YPbPr and Audio In Connectors Video Audio Monitor Out Connectors Video Audio and S Video In Connectors AV2 VGA and CVI 2 Connector for connecting a computer to the TV HDMI Connector for digital input dl 2 O 4 5 6 T 8 I 1 1 sA i Mounting the Television Stand This section provides information on the connectivity available for the respective TV models Refer to the screen size that is relevant to your TV set 32 26 LCD TV _22 Di ED ILC04 SD2 APAC English DFU v7 2 070706 Dda
16. uence of commands 3 19753 MUTE Keyboard Lock The Keyboard Lockout function disables the television s local keyboard for volume and program control Video Out Mute menu option only available in certain models This option allows the user to mute the AV output to prevent unauthorized copying of AV content ma p Control settings In this sub menu the Control settings of the TV can be configured A Control ESP Off Audio Video Mute No Step Tuning No Digit Timeout 3 0 Min Volume 0 Max Yolume 99 ESP Energy Saving Programmability Mode ESP function controls the maximum continuous viewing time allowed and its valid values are 00 99 in hours 00 value means that the ESP function is OFF Note that if the TV is switched off the ESP timer countdown will be reset Audio Video Mute The Audio Video Mute menu function determines whether the video should be blanked and the audio should be muted if the currently tuned channel has no sional Step Tuning If YES is selected TV programs 1 to 9 are tuned immediately when a digit is pressed If NO is selected tuning is performed only after the dash second digit disappears Digit Timeout This is the time out to enter the second digit of program number eg for program number 10 and above Min Volume This item sets the minimum volume level allowed for the television set Use Right Left key to adjust Max Volume This item sets the limit for
17. vity to an external STB 3 Multi RC feature requires specific remote control models RC2887 RC2886 4 The Multi RC default colour code is BLUE for TV and RC The RC colour code will be automatically reset to default BLUE colour when the RC batteries are changed To check the colour code status of TV and RC just press the OK button on the RC for at least 4 seconds No of Channels This sub menu allows setting the number of TV PAY TV Info and Radio channels Channel Install In the Channel Install sub menu various channel settings can be set Please refer to the section on Channel Installation for further details Configuration In the Configuration menu various settings and features of the TV can be adjusted Please refer to the section on Configuration for further details Channel Installation Installation In the Channel Installation sub menu channel settings can be set When this menu is open all the protections are inactive 7 Channel Install e Channel The Channel type can be selected with the cursor Left Right key The available Channel TWO options are TV INFO Input Tuner PAYTV and RADIO System Auto Note Frequency 175 7500 gt Use the numeric keys to enter the Label gt program number For program number below 10 enter the first digit Store as O followed by the program Fine tune 0 number Eg 01 for TV 1 Mute None Alternatively enter the program Auto Install
18. wired method 4107 gt A number display shows from 1 100 the percentage of memory storage progress from the TV to the Wireless Smart Loader 100 fully loaded TV TO SMARTLOADER ie HH gt When the data transfer is completed is 100 the following menu appears for 3 seconds SMARTLOADER READY gt gt Now the Wireless Smart Loader is programmed and can be used to install other TV sets 3 Installing a TV with the Wireless Smart Loader Use a Wireless Smart Loader programmed with the settings from a master TV of the same type Be sure to use the same method of programming the Wireless Smart Loader It means that if you program the Wireless Smart Loader using the wireless method you have to use the same method to install the TV Turn on the TV and point the Wireless Smart Loader to the T V s infra red receiver distance around 30cm Press the MENU Key on the Wireless Smart Loader A Highlight SMARTLOADER TO TV 2 Press the right arrow key on the Wireless Smart Loader for wireless method or on the TV Remote Control for wired method gt A number display shows from 1 100 the percentage of memory storage progress from the Wireless Smart Loader to the TV 100 fully loaded SMARTLOADER TO TV HH gt When data transfer is completed is 100 the following menu appears for 3 seconds TV READY gt gt After that the following menu comes up GOODBYE gt gt
Download Pdf Manuals
Related Search