Pelco CM9740-UPG-8312 Frozen Dessert Maker User Manual
Contents
1. U10 RAM CHIP Figure 4 U10 RAM Chip Reinstall the video output card into slot 17 of the matrix bay refer to Figure 2 Align the top and bottom edges of the card with the top and bottom card guides of the matrix bay b Slide the card toward the rear of the matrix bay until the card is seated firmly with the connectors on the backplane and with the associated rear panel card connector The audible alarm on the power supply should stop beeping the Frame Fault power supply LED light emitting diode should turn off and the LEDs on the video output card should indicate proper operation of the matrix bay To ensure proper operation of the matrix bay reset the video output card by pressing the Reset button on the card refer to Figure 2 For about five seconds the audible alarm on the power supply beeps and the Frame Fault LED flashes red Normal operation is established when the audible alarm stops beeping the Frame Fault LED turns off and the LEDs on the video output card indicate proper operation of the matrix bay Reattach the front panel of the matrix bay by tightening the eight captive panel screws 1547 7 03 APPENDIX B CONNECTING AN ASCII COMMUNICATIONS DEVICE TO THE CM9740 CC1 As stated previously in this manual version 8 03 012 of CM9740 CC1 software is not compatible with version 3 20 or earlier of CM9760 DT CM9760 DT4 software If you wish to replace the existing DT DT4 device external2. click the System Manager 9760 program and then click the Add Remove button A dialog box appears indicating the progress of the removal of the System Manager program When removal of the System Manager program completes click the OK button For a PC running Windows 2000 or XP Click Change or Remove Programs In the Currently installed programs box click the System Manager 9760 program and then click the Remove button At the system prompt asking you whether you are sure you want to remove the System Manager program click Yes The System Manager program is removed NOTE If during the removal of the System Manager program Confirm File Deletion boxes appear asking you to remove shared dll files click Yes Then continue with the removal of the System Manager program Install version 8 03 012 of the System Manager program Using the READ utility of the System Manager program load the current configuration files using the floppy disk from step 4c into the System Manager database The configuration files are upgraded to version 8 03 012 in the System Manager database For information about the READ utility refer to the CM9760 MGR System Management Software Installation Operation manual Using the WRITE utility of the System Manager program copy the new version of configuration files to a floppy disk To prevent overwriting the old version of configuration files do not use the same floppy disk that was used in step 4c Copy the new versi
3. 03 2 3 4 b Verify that the 9760NIU EXE or NET9760 EXE file was renamed to 9760NIU OLD or 9760 010 respectively by entering dir w Insert the System 9760 Network Disk version 8 03 012 into the disk drive of the NW1 Copy the executable file 9760NIU EXE from the Network Disk to the C NETWORK directory on the hard drive of the NW1 At the C NETWORK prompt enter copy a 9760niu exe If the earlier version of your executable file was named NET9760 EXE edit the batch file net bat to point to 9760NIU EXE rather than to NET9760 EXE a At the C prompt change to the NETWORK directory by entering cd network b Edit the net bat file i Enter the following edit net bat il Locate the line that reads as follows NET9760 xNODES where x is the number of nodes in the network iii Edit the line by changing NET9760 to 9760NIU so that the line reads as follows 9760NIU xNODES where x is the number of nodes in the network iv Press Alt F and then type the letter s to save the file v and then type the letter x to exit the file Press Ctrl Alt Del to reboot the CM9760 NW1 Note that you must press the Del key located under the number key on the numeric keypad of your keyboard in order to reboot the system Pressing the other Delete key that is provided on the keyboard will not reboot the system 13 Verify that the multi node system is operating properly APPENDIX A UPGRADING CM9740 MXB
4. FIRMWARE CAUTION Only qualified personnel observing electrostatic discharge ESD precautions should perform the proce dure below Always wear a grounding strap connected to an approved grounding source when working on or near exposed electronic components Handle circuit boards by their edges NOTE You do not need to turn off power to the 9740 in order to upgrade matrix bay firmware To upgrade 9740 firmware to version 8 04 do the following 1 Remove the front panel of the matrix bay by loosening the eight captive panel screws indicated in Figure 1 2 the video output card from slot 17 of the matrix bay refer to Figure 2 To remove the card grasp the two card handles and firmly pull the card out of the connectors on the backplane and associated rear panel card The video output card slides out of the slot Note that unless the audible alarm on the power supply has been disabled the alarm beeps when the video output card 15 removed CAPTIVE PANEL SCREW 4 CAPTIVE PANEL SCREW 4 Figure 1 9740 Front Panel VIDEO OUTPUT CARD SLOT 17 CARD HANDLE FRAME LED HANDLE Figure 2 Video Output Card Slot 17 10 C1547M 7 03 1547 7 03 3 Replace the existing 012 PROM chip on the video output card with the chip supplied in the upgrade kit Locate the existing U12 PROM chip on the video output card refer to Figure 3 Using the pr
5. USA USA amp Canada Tel 800 289 9100 Fax 800 289 9150 International Tel 1 559 292 1981 Fax 1 559 348 1120 www pelco com 1509001 Orangeburg New York Las Vegas Nevada Eindhoven The Netherlands Wokingham United Kingdom Montreal Canada
6. cable to the COM 1 port b For each 9740 in your system upgrade firmware to version 8 04 by replacing the U12 PROM chip located on the video output card with one of the chips supplied in the System 9740 software upgrade kit Refer to Appendix A for detailed instructions to upgrade 9740 firmware to version 8 04 If your 9740 system contains CM9760 DT CM9760 DT4 running software version 3 20 or earlier you must do either of the following e Replace the DT DT4 device in your system with a DT DT4 device that is running version 8 01 e Remove the DT DT4 device in your system and use the internal DT software of the CM9740 CC1 version 8 03 012 To use the internal DT you must connect your ASCII communications device ACD directly to the CM9740 CC1 thereby eliminating connection to the existing DT DT4 device external DT in your system Note that when you replace an external DT with the internal DT you may need to reprogram operator related data using System Manager version 8 03 012 To replace an external DT with the internal DT refer to Appendix B for additional information d Using the AT compatible keyboard attached to the CM9740 CC1 do the following 1 Press Alt N to view your current configuration file name 2 Press Ctrl Q to stop the System 9740 program and to enter DOS mode The C 9740 prompt appears 3 Copy all current configuration files also referred to as flat files from
7. repair or replace without charge any merchandise proved defective in material or workmanship for a period of one year after the date of shipment Exceptions to this warranty are as noted below e Five years on Pelco manufactured cameras CC3500 CC3600 CC3700 and MC3500 MC3600 Series two years on all other cameras hree years on Genex Series multiplexers server and keyboard and 090 Series Camclosure Camera System wo years 100 150 200 and 300 Series Camclosure Camera Systems wo years on all standard motorized or fixed focal length lenses wo years on Legacy 6700 6800 8500 9500 9740 9760 Matrix DF5 and DF8 Series Fixed Dome products wo years on Spectra Esprit and PS20 Scanners including when used in continuous motion applications wo years on Esprit and WW5700 series window wiper excluding wiper blades Eighteen months on DX Series digital video recorders One year except video heads on video cassette recorders VCRs Video heads will be covered for a period of six months Six months on all pan and tilts scanners or preset lenses used in continuous motion applications that is preset scan tour and auto scan modes Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco shipment All goods requiring warranty repair shall be sent freight prepaid to Pelco Clovis California Repairs made necessary by reason of misuse alteration normal wear or
8. the C 9740 directory to a floppy disk At the C 9740 prompt enter the following copy c filename a where filename is your current configuration file name displayed in step 1d 1 For example if your file name is 5 enter the following copy c node5 a 2 Upgrade System Manager software which is located on the external PC connected to the CM9760 NW1 _ If you wish to maintain an archive of event messages recorded in the current System Manager database save the database before it is removed in step 2b below The default location of the System Manager database file sys32db mdb is as follows C Program Files Pelco System Manager 9760 DB sys32db mdb To store the current database file move the database file to a different directory on the hard drive of the System Manager PC or store the database file on a floppy disk and label the disk using a unique name 6 1547 7 03 1547 7 03 b Remove the current System Manager program 1 In the Windows taskbar click the Start button 2 Highlight Settings and then click Control Panel 3 Double click the Add Remove Programs icon 4 running Windows 95 98 NT On the Install Uninstall tab click the System Manager 9760 program and then click the Add Remove button A dialog box appears indicating the progress of the removal of the System Manager program When removal of the System Manager program completes click the OK button For a PC runnin
9. 40 Setup Disk version 3 74 System 9740 Operation Disk version 8 03 012 System 9740 Utility Disk version 8 03 012 CM9740 9760 Resource CD ROM version 8 03 012 2 U12 PROM programmable read only memory chips version 8 04 part number IC53 0042 0804 1 Chip extraction tool part number ICPULLERTOOL CM9740 CC1 System 9740 Controller Installation Operation Manual C1508M A CM9760 MGR System Management Software Installation Operation Manual C547M D This manual provides an overview of the System 9740 software upgrade process and instructions for upgrading the software in single node and multi node systems 1547 7 03 1 SOFTWARE UPGRADE OVERVIEW Upgrading System 9740 software to version 8 03 012 involves upgrading CM9740 CC1 software and System Manager software For proper operation of a 9740 system however additional components such as 9740 and CM9760 KBD CM9760 KBR firmware must also be upgraded The following list summarizes the various components of a 9740 system that must be upgraded CM9740 CC1 system software executable file 9740 which resides in the C 9740 directory on the flash disk of the CC1 Version 8 03 012 of CM9740 EXE is provided on the System 9740 Operation Disk in the System 9740 software upgrade kit CM9740 UPG 831 2 System Manager software Inasingle node system the System Manager software resides on the hard disk of an external PC connected to the CM9740 CC1 Inam
10. 40 directory on the Operation Disk to the C 9740 directory of the CC1 At the C 9740 prompt enter copy a 9740 cm9740 exe Copy all configuration files saved to the floppy disk in step 7 above to the C 9740 directory of the Be careful that you do not copy the configuration files saved to the floppy disk in step 4c above At the 19740 prompt enter copy a filename where filename is the name of the configuration file For example if the file name is test enter the following copy a test CAUTION f you need modify the configuration files in the future do not use the SET97XX program Doing so will corrupt the configuration files When configuration files have been upgraded to version 8 03 012 in the System Manager database as was performed in step 6 above and the upgraded files have been copied to the CC1 you must use the System Manager program on the external PC to modify the files Press Ctrl Alt Del to reboot the 9740 system Verify that the system is operating properly Delete the old configuration files from the floppy disk that was used in step 4c above or save the old configuration files that are on the floppy disk as a backup of the earlier version If you choose to save the old configuration files that are on the floppy disk be careful that you do not mistakenly copy the files back into the CC1 at a future time UPGRADING SYSTEM 9740 SOFTWARE IN A MULTI NODE SYSTEM NOTE Any external computer inter
11. 60 NW1 Upgrade the CM9760 NW1 as follows a If the motherboard included in the NW1 is a Tyan Tomcat or a Tyan Trinity 100AT motherboard upgrade the RAM e lfthe motherboard is a Tyan Tomcat motherboard install the two SIMMs provided in the 9760 8312 upgrade kit SIMMs must be installed in pairs e lfthe motherboard is a Tyan Trinity 100 motherboard remove the two SIMMs that are installed on the motherboard and then install the DIMM provided in the 9760 8312 upgrade kit Note that if the motherboard in the NW1 is an American Predator Raptor AT motherboard you do not need to upgrade the RAM For information about identifying whether the motherboard included in the NW1 is a Tyan Tomcat Tyan Trinity 100AT or American Predator Raptor AT motherboard and for instructions to upgrade RAM on a Tyan Tomcat or Tyan Trinity 100AT motherboard refer to the System 9760 Software Upgrade Installation Manual 9760 8312 CM9760 TOM 8312 CM9760 TRI 8312 b Upgrade the NW1 system software executable file 1 Using the AT compatible keyboard attached to the NW1 do the following a At the C NETWORK prompt rename the executable file f the executable file is named 9760NIU EXE rename the file to 9760NIU OLD by entering rename 9760niu exe 9760niu old he executable file is named NET9760 EXE rename the file to NET9760 OLD by entering rename net9760 exe net9760 old 1547M 7 03 1547 7
12. DT in your system with the use of the internal DT software that is provided in version 8 03 012 of CM9740 CC1 software you must connect the ASCII communications device ACD directly to the CM9740 CC1 thereby eliminating connection to the external DT You can connect an ACD to the CM9740 CC1 in either of the following ways e ACD DB9 connection to CM9740 CC1 089 1 or 2 RS 232 communication standard Refer to the section below titled Connecting an ACD DB9 Port to CM9740 CC1 089 Port for wiring connection information e DB9 RS 232 connection to CM9740 CC1 45 RS 422 In this case the Pelco PV130 RS 232 RS 422 converter is used to provide a bidirectional electrical interface between the RS 232 port of the ACD and the RS 422 port of the CC1 Refer to the section below titled Connecting an ACD DB9 Port to 9740 1 RJ 45 Port for wiring connection information Note the following about use of the internal DT software The operator number of the ACD that connects to a CC1 port defined as an internal DT in the Comms setup file IDT equipment number 48 is automatically assigned the same number as the 1 port number As a result when replacing an external DT with the internal DT you may need to reprogram operator related data using System Manager version 8 03 012 Operator related data is included in the following e Operators setup file e Operator access dialog box in the following system setup file
13. INSTALLATION MANUAL System 9740 Software Upgrade CM9740 UPG 8312 1547 7 03 CONTENTS Section Page INERODUCTION 1 SOFIWARE UPGRADE OVERVIEW oly ast Aan el aden ian od a naga d Pa anaa a aa 2 UPGRADING SYSTEM 9740 SOFTWARE IN A SINGLE NODE SYSTEM isina aaa a EaR 3 UPGRADING SYSTEM 9740 SOFTWARE IN A MULTI NODE SYSTEM 6 UPGRADING CM9740 MXB FIRMWAR E aaa a an rast a R a 10 APPENDIX B CONNECTING AN ASCII COMMUNICATIONS DEVICE TO THE CM9740 CC1 aee naa Naane eaaa eee 13 CONNECTING AN ACD 089 PORT TO CM9740 CC1 089 PORT 66aeaaaa eaaa eaaa eee aaa eaaa eaaa aaa aa aaa aaa NE NGGE NAGA 13 CONNECTING AN ACD DB9 PORT TO A CM9740 CC1 5 PORT en agak a abang a A 14 WARRANTY AND RETURN INFORMATION baa angen aan ia aan gag naa aa vate a aa aa ad baana aa ga aa nara a abad pa kaa aga na a adana 15 LIST OF ILLUSTRATIONS Figure Page 1 9740 Front Panel 2 Video Output Card Slot 17 3 U12 PROM Chip 4 U10 RAM Chip 5 ACD 089 to CM9740 CC1 089 Connection 6 ACD 089 to CM9740 CC1 RJ 45 Connection INTRODUCTION The CM9740 UPG 8312 software upgrade kit provides the following items to upgrade System 9740 software System 97
14. PV130 converter to a 089 port of the ACD If necessary connect 12 VDC power supply to the PV130 converter otherwise proceed to step 3 The power supply allows the PV130 converter to communicate serial port data over wire pairs for distances up to 4 000 feet 1 219 m on the RS 422 side a Connect the black and white striped wire from the power supply to the 12 VDC terminal on the converter b Connect the solid black wire from the power supply to the GND terminal on the converter Connect RX on the converter to terminal 8 RX on the wall block NOTE The numbering of the screw terminals the wall block shown in Figure 6 applies to the Pelco 45 wall block A wall block purchased from a supplier other than Pelco may have a different numbering scheme Connect RX on the converter to terminal 7 RX on the wall block Connect TX on the converter to terminal 1 TX on the wall block Connect TX on the converter to terminal 2 TX on the wall block Connect the wall block to an RJ 45 port of the CC1 using an RJ 45 reversed cable 12 VDC POWER SUPPLY IF NECESSARY ACD MALE DB9 SERIAL PORT RS 232 RS 422 BLOCK REVERSED CABLE CM9740 CC1 REVERSED CABLE CONNECTIONS WALL BLOCK CM9740 CC1 1314 15161718 19 20 RJ 45 RJ 45 Ea eA Ne IES CONNECTOR CONNECTOR ERR ITD Figure 6 ACD DB9 to CM9740 CC1 RJ 45 Connection C1547M 7 03 WARRANTY Pelco will
15. accident are not covered under this warranty Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the specific use or application made of the Products Pelco s liability for any claim whether based on breach of contract negligence infringement of any rights of any party or product liability relating to the Products shall not exceed the price paid by the Dealer to Pelco for such Products In no event will Pelco be liable for any special incidental or consequential damages including loss of use loss of profit and claims of third parties however caused whether by the negligence of Pelco or otherwise The above warranty provides the Dealer with specific legal rights The Dealer may also have additional rights which are subject to variation from state to state WARRANTY AND RETURN INFORMATION a warranty repair is required the Dealer must contact Pelco at 800 289 9100 or 559 292 1981 to obtain a Repair Authorization number RA and provide the following information Model and serial number 2 Date of shipment PO number Sales Order number or Pelco invoice number 3 Details of the defect or problem f there is a dispute regarding the warranty of a product which does not fall under the warranty conditions stated above please include a written explanation with the product when returned Method of return shipment shall be the same or equal to the method by which the item was rece
16. face such as an access control system alarm system fire system building management control system or VMX200 that is using the P protocol to communicate with a CM9740 CC1 running version 7 8 or lower software is not compatible with version 8 03 012 of CM9740 CC1 software Contact Technical Support for additional information To upgrade System 9740 software in multi node system first upgrade all nodes in the network containing a CM9740 CC1 and then upgrade the node containing the CM9760 NW1 network interface unit NIU If your multi node system contains CM9760 CC1 nodes as well as CM9740 CC1 nodes you must also upgrade the 9760 1 nodes Refer to the System 9760 Software Upgrade Installation Manual C1546M for instructions to upgrade CM9760 CC1 nodes To upgrade System 9740 software in a multi node system proceed as follows 1 For the initial CM9740 CC1 node to be upgraded do the following a Upgrade CM9760 KBD and CM9760 KBR firmware to version 8 03 To perform this step obtain the necessary firmware and installation instructions in the CM9760 KBD E80 upgrade kit that is provided for each 9760 CM9760 KBR in your system If you already have CM9760 KBD CM9760 KBR in your system running firmware version 8 03 do the following 1 Log off the KBD KBR 2 Disconnect the KBD KBR by unplugging the cable from the COM 1 port of the KBD KBR 3 Set DIP switch 7 on the KBD KBR to the ON position 4 Reconnect the
17. g Windows 2000 or XP Click Change or Remove Programs the Currently installed programs box click the System Manager 9760 program and then click the Remove button At the system prompt asking you whether you are sure you want to remove the System Manager program click Yes The System Manager program is removed NOTE If during the removal of the System Manager program Confirm File Deletion boxes appear asking you to remove shared dll files click Yes Then continue with the removal of the System Manager program Install version 8 03 012 of the System Manager program which is provided on CD ROM For System Manager installation instructions refer to the CVM9760 MGR System Management Software Installation Operation manual Using the READ utility of the System Manager program load the current configuration files using the floppy disk from step 1d 3 into the System Manager database The configuration files are upgraded to version 8 03 012 in the System Manager database For information about the READ utility refer to the CM9760 MGR System Management Software Installation Operation manual Using the WRITE utility of the System Manager program copy the new version of configuration files to a floppy disk To prevent overwriting the old version of configuration files do not use the same floppy disk that was used in step 1d 3 Copy the new version of configuration files to a different floppy disk and label the disk using a unique name No
18. it CM9760 NW1 RAM random access memory Version 8 03 012 of CM9760 NW1 software requires a minimum of 16 of RAM As a result for those NW1 units containing a Tyan Tomcat or Tyan Trinity motherboard that was shipped from the factory with 8 MB of RAM installed you must upgrade the RAM using the appropriate software upgrade kit CM9760 TOM 8312 9760 8312 NOTE If the CM9760 NW1 contains an American Predator Raptor AT motherboard the RAM does not need to be upgraded The American Predator Raptor AT motherboard is shipped from the factory with 64 MB of RAM installed CM9760 DT CM9760 DT4 Version 8 03 012 of 9740 1 software is not compatible with version 3 20 or earlier of CM9760 DT CM9760 DT4 software Consequently if you have a DT DT4 device in your system that is running version 3 20 or earlier you must do either of the following Replace the DT DT4 device in your system with DT DT4 device that is running version 8 01 Remove the DT DT4 device in your system and use the internal DT software of the 9740 1 version 8 03 012 use the internal DT you must connect your ASCII communications device ACD directly to the CM9740 CC1 thereby eliminating connection to the existing DT DT4 device external DT in your system NOTE In addition to the CM9760 DT CM9760 DT4 as mentioned above be aware that any external computer interface such as an access control system alarm system fire syste
19. ived by Pelco RETURNS order to expedite parts returned to the factory for repair or credit please call the factory at 800 289 9100 or 559 292 1981 to obtain an authorization number CA number if returned for credit and RA number if returned for repair All merchandise returned for credit may be subject to a 20 restocking and refurbishing charge Goods returned for repair or credit should be clearly identified with the assigned CA or RA number and freight should be prepaid Ship to the appropriate address below If you are located within the continental U S Alaska Hawaii or Puerto Rico Service Department Pelco 3500 Pelco Way Clovis CA 93612 5699 lf you are located outside the continental U S Alaska Hawaii or Puerto Rico Intermediate Consignee Ultimate Consignee American Overseas Air Freight Pelco 320 Beach Road 3500 Pelco Way Burlingame CA 94010 Clovis CA 93612 5699 USA USA REVISION HISTORY Manual Date Comments C1547M 7 03 Original version Pelco the Pelco logo System 9760 Spectra Genex Esprit Camclosure Legacy and Coaxitron are registered trademarks of Pelco Tyan is a registered trademark of Tyan Computer Corporation TM System 9740 is a trademark of Pelco TM American Predator and Raptor AT are trademarks of American Predator Corporation 1547 7 03 Copyright 2003 Pelco All rights reserved PELCO World Headquarters 3500 Pelco Way Clovis California 93612
20. m building management control system or VMX200 that is using the P protocol to communicate with a CM9740 CC1 running version 7 8 or lower software is not compatible with version 8 03 012 of CM9740 CC1 software Contact Technical Support for additional information For instructions to upgrade System 9740 software in a single node system refer to Upgrading System 9740 Software Single Node System For instructions to upgrade System 9740 software in a multi node system refer to Upgrading System 9740 Software in a Multi Node System C1547M 7 03 UPGRADING SYSTEM 9740 SOFTWARE IN A SINGLE NODE SYSTEM 1547 7 03 NOTE Any external computer interface such as an access control system alarm system fire system building management control system or VMX200 that is using the P protocol to communicate with a 9740 1 running version 7 8 or lower soft ware is not compatible with version 8 03 012 of CM9740 CC1 software Contact Technical Support for additional information To upgrade System 9740 software single node system proceed as follows d 2 3 4 a b 5 Upgrade CM9760 KBD 9760 firmware to version 8 03 To perform this step obtain the necessary firmware and installation instructions in the CM9760 KBD E80 upgrade kit that is provided for each CM9760 KBD CM9760 KBR your system If you already have CM9760 KBD CM9760 KBR in your system ru
21. nning firmware version 8 03 the following Log off the KBD KBR Disconnect the KBD KBR by unplugging the cable from the COM 1 port of the KBD KBR Set DIP switch 7 on the KBD KBR to the ON position Reconnect the cable to the COM 1 port For each 9740 in your system upgrade firmware to version 8 04 by replacing the 012 PROM chip located on the video output card with one of the chips supplied in the System 9740 software upgrade kit Refer to Appendix A for detailed instructions to upgrade 9740 firmware to version 8 04 the following a If your 9740 system contains a CM9760 DT CM9760 DT4 running software version 3 20 or earlier you must do either of Replace the DT DT4 device in your system with a DT DT4 device that is running version 8 01 Remove the DT DT4 device in your system and use the internal DT software of the CM9740 CC1 version 8 03 012 To use the internal DT you must connect your ASCII communications device ACD directly to the CM9740 CC1 thereby eliminating connection to the existing DT DT4 device external DT in your system Note that when you replace an external DT with the internal DT you may need to reprogram operator related data using System Manager version 8 03 012 To replace an external DT with the internal DT refer to Appendix B for additional information Using the AT compatible keyboard attached to the CM9740 CC1 do the following Press Alt N to view your current configu
22. on of configuration files to a different floppy disk and label the disk using a unique name Note that you will need to use the disk containing the new version of configuration files later in this procedure as directed For information about the WRITE utility refer to the CM9760 MGR System Management Software Installation Operation manual Using the AT compatible keyboard attached to the do the following a At the C 9740 prompt rename the CM9740 EXE file to CM9740 0LD by entering rename cm9740 exe 9740 0 1 b Verify that the CM9740 EXE file was renamed to 9740 010 by entering dir w Delete the existing configuration files by entering del filename xxx where filename is the configuration file name and xxx is the extension of the file name mon cam mac scp alm gpi pin sym lcm idn For example if the file name is test then the commands used to delete configuration files are as follows del test mon del test cam del test mac del test scp del test alm del test gpi del test pin del test sym del test lcm del test idn CAUTION Do not delete the test bat file If you delete the test bat file the 9740 system will not start when it is rebooted C1547M 7 03 1547 7 03 Upgrade the system software executable file 9740 a Insert the System 9740 Operation Disk Version 8 03 012 into the disk drive of the CC1 the CM9740 EXE executable file from the 97
23. ovided extraction tool remove the U12 PROM chip from its socket Remove the chip slowly to avoid damaging the socket Remove the replacem ent PROM chip from the electrostatic bag Note the alignment notch at the top of the chip refer to Figure 3 Orient the chip so that the notch on the chip aligns with the notch carefully press the ch that is drawn on the surface of the circuit board Verify pin to socket alignment and then ip into its socket until the chip is seated completely 4 the RAM random access memory stored on the U10 chip a Locate the existing U1 0 RAM chip on the video output card refer to Figure 4 Note the location of the chip in its socket the top two pins on either side of the socket are not used Using the provided extraction tool remove the U10 chip from its socket Remove the chip slowly to avoid damaging the socket Wait two minutes and then reinstall the chip into its socket in the same position noted in step 4a Verify pin to socket alignment and then carefully press the chip into its socket until the chip is seated completely ALIGNMENT U12 PROM CHIP Figure 3 U12 PROM Chip
24. ration file name Press Ctrl 0 to stop the System 9740 program and to enter DOS mode The C 9740 prompt appears Copy all current configuration files also referred to as flat files from the C 9740 directory a floppy disk At the C 9740 prompt enter the following copy c filename a where filename is your current configuration file name displayed in step 4a For example if your file name is test default name assigned at the factory enter the following copy c test a After the files are copied label the floppy disk using a unique name Note that you will need to use the disk later in this procedure as directed Upgrade System Manager software If you wish to maintain an archive of event messages recorded in the current System Manager database save the database before it is removed in step 5b below The default location of the System Manager database file sys32db mdb is as follows C Program Files Pelco System Manager 9760 DB sys32db mdb To store the current database file move the database file to a different directory on the hard drive of the System Manager PC or store the database file on a floppy disk and label the disk using a unique name 6 b Remove the current System Manager program 1 In the Windows taskbar click the Start button 2 Highlight Settings and then click Control Panel 3 Double click the Add Remove Programs icon 4 Fora running Windows 95 98 NT On the Install Uninstall tab
25. rectory of the Be careful that you do not copy the configuration files saved to floppy disk in step 1d 3 above At the C 9740 prompt enter copy a filename where filename is the name of the configuration file For example if the file name is 5 enter the following a node5 CAUTION f you need modify the configuration files in the future do not use the SET97XX program Doing so will corrupt the configuration files When configuration files have been upgraded to version 8 03 012 in the System Manager database as was performed in step 3 above and the upgraded files have been copied to the CC1 you must use the System Manager program on the external PC to modify the files Press Ctrl Alt Del to reboot the node Verify that the system is operating properly Delete the old configuration files from the floppy disk that was used in step 1d 3 above or save the old configuration files that are on the floppy disk as a backup of the earlier version If you choose to save the old configuration files that are on the floppy disk be careful that you do not mistakenly copy the files back into the CC1 at a future time Repeat steps 1 and 3 10 for all other CM9740 CC1 nodes in the network To upgrade CM9760 CC1 nodes in the network refer to the System 9760 Software Upgrade Installation Manual provided in the software upgrade kit for each node After all CC1 nodes are upgraded proceed to step 12 to upgrade the CM97
26. s setup file setup file Alarms setup file General Purpose Interface GPI setup file Link cameras setup file Note that you can avoid the need to reprogram operator related data by connecting the ACD to an available CC1 port whose number matches the operator number that was programmed for the ACD when it was connected to an external DT The operator number that was programmed for the ACD is defined in the Operators setup file However you must then program the internal DT as a keyboard and may then need to reprogram keyboard access in the Monitors setup file CONNECTING AN ACD 089 PORT TO 9740 1 089 PORT 1547 7 03 Connect a 089 port of the ACD to the 089 1 COM 2 port of the CC1 using a null modem cable Refer to Figure 5 for wiring connections In Figure 5 the ACD connects to the COM 1 port of the CC1 9740 1 ACD MALE DB9 SERIAL 13 14 15161718 19 20 PORT RCIA TA TEPEE go emmy En RS 232 NULL MODEM CABLE NULL MODEM CABLE WIRING ACD CM9740 CC1 DB9 PORT DB9 PORT PIN 2 RX PIN 2 RX PIN 3 5 GND PIN 5 GND Figure 5 ACD DB9 CM9740 CC1 DB9 Connection CONNECTING AN ACD 089 PORT TO CM9740 CC1 RJ 45 PORT To connect an ACD 089 port 9740 1 45 port refer to Figure 6 and do the following 1 2 Connect the 9 pin side of the
27. te that you will need to use the disk containing the new version of configuration files later in this procedure as directed For information about the WRITE utility refer to the CM9760 MGR System Management Software Installation Operation manual Using the AT compatible keyboard attached to the initial CC1 being upgraded do the following a At the C 9740 prompt rename the CM9740 EXE file to 9740 010 by entering rename cm9740 exe 9740 0 1 b Verify that the CM9740 EXE file was renamed to CM9740 0LD by entering dir w c Delete the existing configuration files by entering del filename xxx where filename is the configuration file name and xxx is the extension of the file name mon cam mac scp alm gpi pin sym Icm or idn For example if the file name is 5 then the commands used to delete configuration files are as follows del node5 mon del node5 cam del node5 mac del node5 scp del node5 alm del node5 gpi del node5 pin del node5 sym del 5 1 del node5 idn Upgrade the CC1 system software executable file 9740 a Insert the System 9740 Operation Disk Version 8 03 012 into the disk drive of the the 9740 executable file from the 9740 directory on the Operation Disk to the C 9740 directory of the At the C 9740 prompt enter copy a 9740 cm9740 exe Copy all configuration files saved to floppy disk in step 4 above to the C 9740 di
28. ulti node system the System Manager software resides on the hard disk of an external PC connected to the CM9760 NW1 Version 8 03 012 of the System Manager software is provided on the CM9740 9760 Resource CD ROM in the System 9740 software upgrade kit CM9740 MXB firmware For compatibility between the 9740 firmware and version 8 03 012 of 9740 1 software the U12 PROM chip on the video output card of each matrix bay in the 9740 system must be upgraded to version 8 04 Two U12 PROM chips version 8 04 are provided in the System 9740 software upgrade kit CM9760 KBD CM9760 KBR firmware For compatibility between the CM9760 KBD CM9760 KBR firmware and version 8 03 012 of 9740 1 software the firmware of each 9760 9760 in the 9740 system must be upgraded to version 8 03 The necessary firmware and instructions for upgrading KBD KBR firmware to version 8 03 are provided in the CM9760 KBD E80 upgrade kit CM9760 NW1 system software executable file 9760 which resides in the C NETWORK directory on the hard disk of the NW1 in a multi node system The CM9760 NW1 is commonly referred to as the network interface unit NIU in a multi node system Version 8 03 012 of 9760NIU EXE is provided on the System 97609 Network Disk which is included in the appropriate System 9760 software upgrade kit for the NW1 in your system 9760 8312 9760 8312 or CM9760 TRI 8312 upgrade k
Download Pdf Manuals
Related Search