Pelco C2491M-B Switch User Manual
Contents
1. Twisted Pair Blue wire Video Gray wire Video Connect the power wires Voltage Red Wire Black Wire 12 VDC Ground 24 VAC AC Operation Only If you are wiring more than one ICSO90 Camclosure to the same transformer connect one side of the transformer to the red wire on all units and connect the other side of the transformer to the b the same way will cause the cameras to be out of phase with each other and may produce a vertical roll when switching between cameras ack wire on all units Failure to connect all of the units Attach the surface trim ring and back box to the adapter plate with the two 8 32 x 2 50 inch screws supplied 8 32 X 1 00 Lh SUPPLIED 4S STANDARD ELECTRICAL BOX ADAPTER RING 8 32 X 2 50 SUPPLIED BACK BOX AND SURFACE MOUNT RING Figure 7 4S Standard Electrical Box Installation C2462M B 10 05 Installation in a 4S Deep Electrical Box Refer to Figure 8 for the following steps 1 Remove the surface mount ring from the back box Refer to Figure 5 and do the following a Place fingers on the circular marks located on the sides of the surface mount ring b Pinch the sides c Lift and remove the surface mount ring from the back box Attach the adapter ring to the 4S box with the two 8 32 x 1 00 inch screws supplied Connect the video cable wires BNC Connect the BNC connector from the Camclosure to a mating2. BNC connector Twisted Pair Blue wire Video Gray wire Video Connect the power wires Voltage Red Wire Black Wire 12 VDC Ground 24 VAC AC Operation Only If you are wiring more than one ICSO90 Camclosure to the same ransformer connect one side of the transformer to the red wire on all units and connect the other side of the transformer to the black wire on all units Failure to connect all of the units he same way will cause the cameras to be out of phase with each other and may produce a vertical roll when switching between cameras Attach the back box to the adapter plate with the two 8 32 x 750 inch screws supplied 4S DEEP ELECTRICAL BOX CEILING WALL 8 32 x 1 00 gt SUPPLIED 8 32 X 750 BACK SUPPLIED BOX Figure 8 4S Deep Electrical Box Installation C2462M B 10 05 11 CAMERA POSITIONING Manually rotate and tilt the camera module to position the camera Do not over rotate the module Excessively turning the module in one direction could result in damage to the wiring Tilt 140 Pan 360 Rotation 360 Figure 9 How to Position Camera 12 C2462M B 10 05 CAMERA ADJUSTMENTS VARIFOCAL LENS ZOOM AND FOCUS ADJUSTMENTS 1 Select a field of view by turning the zoom adjustment ring clockwise counterclockwise Refer to Figure 10 2 Tighten the zoom locking screw 3 Adjust the focus by moving the focus lo
3. NOTE The preferred method for camera rn eee phase adjustment is to use a dual trace oscilloscope to align the vertical sync pulses of the reference camera to the selected cameras Figure 12 Vertical Phase Adjustment C2462M B 10 05 15 REINSTALL THE DOME DOME LINER INSTALLATION If the unit is supplied with a dome liner reinstall the liner before installing the bubble To install the liner refer to Figure 13 and do the following 1 Align the studs located on the camera module with the clips on the liner 2 Lightly pinch the sides of the liner opposite from the clips and place clips over the studs 3 Once the liner is secure position the viewing window of the liner over the lens of the camera 4 Install the bubble Figure 13 How to Install the Dome Liner BUBBLE INSTALLATION To install the bubble refer to Figure 14 and do the following 1 Align the standoffs of the bubble with the slots of the back box 2 Turn the bubble clockwise until it locks in place Figure 14 How to Install the Bubble 16 C2462M B 10 05 SERVICE CONNECTOR An optional 4 foot service monitor cable part number ICSO90 SC is available for on site setup and adjustments To use the cable simply plug one end of the cable directly into the service connector of the ICSO90 and connect the other end to any standard BNC VIDEO IN connector on a monitor To assemble a longer service cable for the ICS090 Series Camclosure purchase t
4. from the back box Refer to Figure 5 and do the following a Place fingers on the circular marks located on the sides of the surface mount ring b Pinch the sides c Lift and remove the surface mount ring from the back box Connect the video cable wires BNC Connect the BNC connector from the Camclosure to a mating BNC connector Twisted Pair Blue wire Video Gray wire Video Connect the power wires Voltage Red Wire Black Wire 12 VDC Ground 24 VAC AC Operation Only If you are wiring more than one ICSO90 Camclosure to the same transformer connect one side of the transformer to the red wire on all units and connect the other side of the transformer to the black wire on all units Failure to connect all of the units the same way will cause the cameras to be out of phase with each other and may produce a vertical roll when switching between cameras Use 3 16 toggle bolts and attach the back box to the mounting surface CEILING WALL 3 16 TOGGLE BOLTS NOT SUPPLIED Figure 6 In Ceiling Installation to a Fixed Ceiling Wall C2462M B 10 05 Installation to Surface of a 4S Standard Electrical Box Refer to Figure 7 for the following steps Attach the adapter ring to the 4S box with the two 8 32 x 1 00 inch screws supplied 1 2 Connect the video cable wires BNC Connect the BNC connector from the Camclosure to a mating BNC connector
5. surface mount ring because it is required to complete the installation Turn the surface mount ring upside down and place it on the inside of the ceiling tile Attach the back box to the ceiling tile and surface mount ring with the two SURFACE MOUNT RING 10 32 x 1 50 inch self tapping screws supplied Replace the ceiling tile Remove an adjacent ceiling tile and connect the video cable wires BNC Connect the BNC connector from the Camclosure to a mating 10 32 x 1 50 BNC connector oe Twisted Pair Blue wire Video SUPPLIED Gray wire Video Figure 4 Ceiling Tile Installation Connect the power wires Voltage Red Wire Black Wire 12 VDC Ground STANDOFF 24 VAC AC Operation Only If you are wiring more than one ICS090 Camclosure to the same transformer connect one side of the transformer to the red wire on all units and connect the other side of the transformer to the black wire on all units Failure to connect all of the units the same way will cause the cameras to be out of phase with each other and may produce a vertical roll when switching between MOUNT RING cameras Figure 5 How to Remove Surface Mount Ring from Back Box C2462M B 10 05 In Ceiling Installation Fixed Ceiling Wall Refer to Figure 6 for the following steps 1 2 Cut a four inch diameter hole in the ceiling wall Remove the surface mount ring
6. 0 days from the date of Pelco shipment All goods requiring warranty repair shall be sent freight prepaid to Pelco Clovis California Repairs made necessary by reason of misuse alteration normal wear or accident are not covered under this war ranty Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the specific use or application made of the Products Pelco s liability for any claim whether based on breach of contract negligence infringement of any rights of any party or product liability relating to the Products shall not exceed the price paid by the Dealer to Pelco for such Products In no event will Pelco be liable for any special incidental or consequential damages including loss of use loss of profit and claims of third parties however caused whether by the negligence of Pelco or other wise he above warranty provides the Dealer with specific legal rights The Dealer may also have additional rights which are subject to variation from state to state a warranty repair is required the Dealer must contact Pelco at 800 289 9100 or 559 292 1981 to obtain a Repair Authorization number RA and provide the following information Model and serial number 2 Date of shipment P O number Sales Order number or Pelco invoice number 3 Details of the defect or problem there is a dispute regarding the warranty of a product which does not fall under the warranty condition
7. 2X camera models which have a five year warranty e Two years on standard motorized or fixed focal length lenses e Two years on Legacy CM6700 CM6800 CM9700 Series matrix and DF5 DF8 Series fixed dome products Two years on Spectra Esprit ExSite and PS20 scanners including when used in continuous motion applications e Two years on Esprit and WW5700 Series window wiper excluding wiper blades Two years except lamp and color wheel on Digital Light Processing DLP displays The lamp and color wheel will be covered for a period of 90 lays The air filter is not covered under warranty e Eighteen months on DX Series digital video recorders NVR300 Series network video recorders and Endura Series distributed network based video products months on DX Series digital video recorders NVR300 Series network video recorders Endura Series distributed network based video products and TW3000 Series twisted pair transmission products e One year except video heads on video cassette recorders VCRs Video heads will be covered for a period of six months e Six months on all pan and tilts scanners or preset lenses used in continuous motion applications that is preset scan tour and auto scan modes Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco shipment All goods requiring warranty repair shall be sent freight will warrant all replacement parts and repairs for 9
8. ADDENDUM Addendum No C3409M Date December 22 2005 Manuals Affected C2462M B C2403M C C2410M H C2491M B C2496M Manual Update Switch Settings for Varifocal Lens Manual Update The high resolution camera with vari focal lens and auto iris is configured at the factory for automatic exposure SWITCH SETTINGS FOR VARIFOCAL LENS The high resolution camera with varifocal lens and auto iris is configured at the factory for automatic exposure 1 AWB Automatic white balance FACTORY SETTINGS 2 GAM Gamma function 12345678 a 3 AGC Automatic gain control EEEOGOCUCSEIIE bd E 4 ESC Electronic shutter control OOCe8eod gd OF s 5 BLC Backlight compensation OFF hd er 6 FL Flickerless EE SWITCH POSITION 7 AE Automatic exposure 8 Not used Figure 1 Switch Settings for Varifocal Lens Pelco Worldwide Headquarters 3500 Pelco Way Clovis California 93612 USA USA amp Canada Tel 800 289 9100 Fax 800 289 9150 International Tel 1 559 292 1981 Fax 1 559 348 1120 www pelco com INSTALLATION 090 Series Camclosure Indoor Integrated Camera System C2462M B 10 05 CONTENTS Section Page IMPORTANT SAFEGUARDS AND WARNINGS a nenrenerenrseuneenrerenesenreennernerenn 3 WELGOME rennntacreesennebersterenanaeri derest za wa ws 4 REMOVE THE BUBB ES ue e 5 INSTALL THE BACK BOX cessccssseessssesssessssecssessssessssssusesscssuecssssssussssssssessusessiesssessseesseessseessueesseesny 6 INSTAL
9. LATION TO SURFACE OF A CEILING WALL eenen 7 IN CEILING INSTALLATION SUSPENDED CEILING 8 IN CEILING INSTALLATION FIXED CEILING WALL 9 CAMERA POSITIONING eeen CAMERA ADJUSTMENTS o n REINSTALL THE DOME eenen SERV SPEC WARRANTY AND RETURN INFORMATION INSTALLATION TO SURFACE OF A 4S STANDARD ELECTRICAL BOX 10 INSTALLATION IN A 4S DEEP ELECTRICAL BOX VARIFOCAL LENS ZOOM AND FOCUS ADJUSTMENTS VARIFOCAL LENS AUTO IRIS LEVEL ADJUSTMENT nennen SWITCH SETTINGS recce ienasi eri entente nend 1 SWITCH SETTINGS FOR FIXED FOCAL LENGTH LENS WITHOUT AUTO IRIS SWITCH SETTINGS FOR VARIFOCAL LENS ennen eneen VERTICAL PHASE ADJUSTMENT 24 VAC OPERATION ONLY 1 HOW TO ADJUST THE PHASE CONTROL DOME LINER INSTALLATION sassen eenander bietet BUBBLE INSTALLATION ICE CONNECTOR De IFIGATIONS iiinis LIST OF ILLUSTRATIONS Figure Page 1 Howto Remove the Bubble arcane rset aeta 5 2 Ceiling Wall nstallati sarren ennn arn oneens 7 3 Concrete Ceiling Wall Installation nnn nnen eneseenereneneneeneeenenensennrenenn 7 4 Ceiling Tile Installation nnn nnee 8 5 How to Remove Surface Mount Ring From Back Box nnee 8 6 In ceiling Installation to a Fixed Ceiling Wall nnee 9 7 AS Standard Electrical Box Installation nonnen ennen 10 8 AS Deep Electrical Box Installation nnn nnen enen eeens 11 g Haw te Position Camerana eeen enne 12 10 Location of Zoo
10. an head screws 8 32 x 750 inch self tapping screws 8 32 x 2 50 inch self tapping screws 10 32 x 1 50 inch self tapping screws BD NNN 4 C2462M B 10 05 REMOVE THE BUBBLE Turn the bubble counterclockwise and lift refer to Figure 1 Place the bubble on a non abrasive surface If the unit is supplied with a liner remove the liner before installing the unit To remove the liner gently lift it from the unit Place the liner to the side it will be reinstalled along with the bubble after the installation has been completed Figure 1 How to Remove the Bubble C2462M B 10 05 INSTALL THE BACK BOX The installation methods for the ICSO90 Series include the following Mount to the surface of a ceiling wall Install in a suspended ceiling Install in a fixed ceiling wall Mount to the surface of a 4S standard electrical box Install in a 4S deep electrical box Select the best method for your installation and refer to the following pages for instructions 6 C2462M B 10 05 Installation to Surface of a Ceiling Wall Refer to Figure 2 for the following steps Refer to Figure 3 if installing the unit to a concrete ceiling wall 1 Pull video and power wires through the ceiling wall 2 Connect the video cable wires BNC Connect the BNC connector from the Camclosure to a mating BNC connector Twisted Pair Blue wire Video Gray wire Video 3 Connect the power wires Voltage Red Wire Black Wi
11. ate White Indoor 32 F to 120 F 0 to 49 C 52 Ib 24 kg 2 Ib 91 kg Design and product specifications subject to change without notice 5 30 13 46 5 72 14 53 m 1 65 4 19 y A zo T 10 26 neat 2 39 6 07 3 90 3 90 9 91 9 91 lt TY EES NOTE VALUES IN PARENTHESES ARE CENTIMETERS ALL OTHERS ARE INCHES with directive 2002 96 ec of the european union regarding the disposal of waste electrical and electronic K This equipment contains electrical or electronic components that must be recycled properly to comply equipment weee Contact your local dealer for procedures for recycling this equipment REVISION HISTORY Manual Date C2462M 11 02 C2462M A 1 03 C2462M B 10 05 18 Comments Original version Added Regulatory Notices for FCC Class B Revised switch setting descriptions for varifocal lens Added WEEE statement C2462M B 10 05 PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace without charge any merchandise proved defective in material or workmanship for a period of one year after the date of shipment Exceptions to this warranty are as noted below e Five years on FT FR8000 Series fiber optic products e Three years on Genex Series products multiplexers server and keyboard e Three years on Camclosure and fixed camera models except the CC3701H 2 CC3701H 2X CC3751H 2 CC3651H 2X MC3651H 2 and MC3651H
12. cking screw clockwise counterclockwise 4 Tighten the focus locking Screw Figure 10 Location of Zoom and Focus Adjustments VARIFOCAL LENS AUTO IRIS LEVEL ADJUSTMENT To adjust the auto iris level do the following AUTO IRIS 1 Manually rotate the camera ADJUSTMENT module to access the auto iris level adjustment refer to Figure 11 2 Turn the screw clockwise to decrease the brightness level and counterclockwise to increase the brightness level ie ZA Figure 11 Varifocal Lens Adjustments C2462M B 10 05 13 SWITCH SETTINGS Switch Settings for Fixed Focal Length Lens Without Auto Iris Refer to the switch drawing The switch is located next to the lens Automatic backlight compensa tion factory setting is used under varying lighting conditions such as outdoors or fixed lighting conditions where there are no bright spots that darken other picture details Manual backlight compensation is used in fixed lighting conditions to optimize the picture detail when there are bright spots FACTORY SETTINGS ALC ELC switch Always ELC 9 2 a gt M 4a Y DC switch Not used ON g Auto backlight compensation BLC switch OFF OFF 2 ABL switch ON 9 8E E Manual backlight compensation BLC switch ON oe ABL switch OFF SWITCH SETTINGS FOR VARIFOCAL LENS The high resolution camera with varifocal lens and auto iris is configured at the factory for optimal performa
13. f Off 10000 Off Off Off C2462M B 10 05 VERTICAL PHASE ADJUSTMENT 24 VAC OPERATION ONLY When using more than one camera power supply a brief vertical roll may occur on the monitor when a camera view is switched To eliminate vertical roll reverse the 24 VAC connections on one camera If both cameras are connected to the same transformer this should solve the problem If reversing the connections does not solve the problem adjust the phase control by synchronizing or line locking the cameras to one another How to Adjust the Phase Control It may be necessary to have two people in communication when synchronizing the cameras one person at the camera and another person at the monitor to observe the vertical roll and the effect of any adjustments made at the camera To synchronize the cameras 1 Choose a reference camera to which all other cameras will be phased 2 Select a camera and synchronize it to the reference camera by turning the phase adjustment control refer to Figure 12 clockwise and or counterclockwise 3 Each time an adjustment is made switch back and forth between the camera you are adjusting and the reference camera Repeat this process as many times as necessary until the roll between VERTEL the cameras is no longer noticeable PHASE ADJUSTMENT 4 Adjust the phase of all other cameras by repeating steps 2 through 3 Always adjust to the reference camera selected in step 1
14. he following parts at a local electronics supply store 1 2 5 mm monaural headphone plug 1 CPM 88 miniature coaxial connector 1 RG174 U coaxial cable To assemble the cable 1 Attach the CPM 88 miniature coaxial connector to one end of the cable Follow the directions supplied with the miniature coaxial connector 2 Refer to Figure 15 and do the following to attach the 2 5 mm monaural plug to the other end of the coaxial cable a Remove the support sleeve from the plug and then slip the support sleeve over the end of the cable b Prepare the cable c Solder the center connector of the cable to the center pin of the plug d Thread the braid of the cable through the hole in the crimp pin and then solder the braid to the top of the crimp pin e Crimp the end of the crimp pin around the cable f Reassemble the support sleeve and the plug CENTER CONDUCTOR CABLE BRAID SHIELD 2 5 mm MONAURAL HEADPHONE PLUG Figure 15 How to Connect the 2 5 mm Monaural Headphone Plug to the Coaxial Cable C2462M B 10 05 17 SPECIFICATIONS BACKBOX Electrical Input Voltage Power Consumption Video Connector General Pan Tilt Adjustment Pan Tilt Rotation Construction Back Box and Surface Mount Ring Bubble Finish Environment Operating Temperature Weight Unit Shipping 12 VDC or 24 VAC 10 auto sensing 3 watts or less BNC 360 140 20 to 160 range 360 ABS plastic Polycarbon
15. is no guarantee that the interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and the receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help Changes and Modifications not expressly approved by the manufacturer or registrant of this equipment can void your authority to operate this equipment under Federal Communications Commissions rules C2462M B 10 05 3 Thank you for purchasing Pelco s Camclosure Integrated Camera System for indoor applications The ICSO90 Series system integrates a camera and lens package in a small discreet dome The system is easy to install and can be mounted to the surface of a ceiling wall or recessed in a ceiling wall Prior to installation of your new system thoroughly familiarize yourself with the information in this manual The following is supplied with the 090 Series Camclosure Integrated Camera System Qty Description Assembled ICS090 Series Camclosure back box bubble and camera module Adapter plate 8 32 x 1 00 inch Phillips p
16. m and Focus Adjustments nnen senen eenseneneenseeneensverneeneneens 13 Ti Varifocal Lens Adjustments nnen dee tn 13 12 Vertical Phase Adjustment cc ccccececcstssceseseseesesveseessasessessssessarsstessavesesssassearsaeeseaneaees 15 13 How to Install the Dome Liner nnee eneneensensensensensensenseneeneenn tantes 16 14 How to Install the Bubble nnen eenen eensensensensensensensensenenenn tenten 16 15 How to Connect the 2 5 mm Monaural Headphone Plug to the Coaxial Cable 17 C2462M B 10 05 IMPORTANT SAFEGUARDS AND WARNINGS 1 Installation and servicing should be done only by qualified service personnel and conform to all local codes 2 Unless the unit is specifically marked as a NEMA Type 3 3R 3S 4 4X 6 or 6P enclosure it is designed for indoor use only and must not be installed where exposed to rain and moisture 3 Use only installation methods and materials capable of supporting four times the maximum specified load REGULATORY NOTICES This equipment has been tested and found to comply with the limits of a Class B digital device pursuant to part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there
17. nce in lighting conditions where auto iris is required It is also configured with the shutter speed set at 1 60 NTSC or 1 50 PAL and manual gain set at 6 dB AE Functions onon RAUN For manually setting and locking the white balance Place a white background in front of camera and turn off switch 1 For gamma correction Switch to accurately reproduce scene brightness when turned on y 0 6 and when turned off y 1 0 For automatic exposure Turn on switch 7 and then turn on off switch 3 for AGC switch 4 for electronic shutter control switch 5 for backlight compensation and switch 6 for flickerless motion For manual exposure and to enable auto iris Turn off switch 7 set switch 3 on to increase the gain by 6 dB or off to increase the gain by 18 dB set switches 4 5 and 6 for the desired shutter speed AWB Automatic white balance Hl SWITCH POSITION GAM Gamma function FAS TORY eee AGC Automatic gain control 12345678 ESC Electronic shutter control W E E E EE E BLC Backlight compensation HCOoOugagaHEHO FL Flickerless OFF AE Automatic exposure Em SWITCH POSITION Not used itso WARNING Do not change the shutter speed unless you understand how changing the settings will affect the scene detail Shutter Switch Number and Position Speed 7 6 5 4 60 NTSC ee On On On 100 Off On On 250 off On Off On 500 Off Off On 1000 On On Off 2000 Off On Off 4000 On Of
18. re 12 VDC Ground 24 VAC AC Operation Only If you are wiring more than one ICSO90 Camclosure to the same ransformer connect one side of the transformer to the red wire on all units and connect the other side of the transformer to the black wire on all units Failure to connect all of the units he same way will cause the cameras to be out of phase with each other and may produce a vertical roll when switching between cameras 4 Use 6 32 toggle bolts and ne g attach the surface mount Aana ET rinig and back bax to the ID CD mounting surface For a concrete ceiling wall installation use 8 32 mounting hardware 6 32 TOGGLE BOLTS NOT SUPPLIED L BACK BOX AND SURFACE MOUNT RING Figure 2 Ceiling Wall Installation CONCRETE WALL OR CEILING LHE T Hi 8 32 MOUNTING HARDWARE NOT SUPPLIED BACK BOX AND SURFACE MOUNT RING Figure 3 Concrete Ceiling Wall Installation C2462M B 10 05 7 In Ceiling Installation Suspended Ceiling Refer to Figure 4 for the following steps 1 2 Remove the ceiling tile from the ceiling Cut a four inch diameter hole in the ceiling tile Remove the surface mount ring from the back box Refer to Figure 5 and do the following a Place fingers on the circular marks located on the sides of the surface mount ring b Pinch the sides c Lift and remove the surface mount ring from the back box Do not discard
19. s stated above please include a written ex planation with the product when returned Method of return shipment shall be the same or equal to the method by which the item was received by pelco RETURNS n order to expedite parts returned to the factory for repair or credit please call the factory at 800 289 9100 or 559 292 1981 to obtain an authori zation number CA number if returned for credit and RA number if returned for repair All merchandise returned for credit may be subject to a 20 restocking and refurbishing charge Goods returned for repair or credit should be clearly identified with the assigned CA or RA number and freight should be prepaid Ship to the appro priate address below you are located within the continental U S Alaska Hawaii or Puerto Rico send goods to Service Department Pelco 3500 Pelco Way Clovis CA 93612 5699 you are located outside the continental U S Alaska Hawaii or Puerto Rico and are instructed to return goods to the USA you may do one of the ollowing the goods are to be sent by a FORWARDER send the goods to COURIER SERVICE send the goods to Pelco c o Expeditors Pelco 473 Eccles Avenue 3500 Pelco Way South San Francisco CA 94080 USA Clovis CA 93612 5699 USA Phone 650 737 1700 the goods are to be sent by a FREIGHT Fax 650 737 0933 Pelco the Pelco logo Camclosure Esprit Genex Legacy and Spectra are registered trademarks of Pelco Copyright 2005 Pelco Endura and E
20. xSite are trademarks of Pelco All rights reserved DLP is a registered trademark of Texas Instruments Inc PELCO World Headquarters 3500 Pelco Way Clovis California 93612 USA USA amp Canada Tel 800 289 9100 Fax 800 289 9150 International Tel 1 559 292 1981 Fax 1 559 348 1120 www pelco com 1S09001 United States Canada United Kingdom The Netherlands Singapore Spain Scandinavia France Middle East
Download Pdf Manuals
Related Search