Panasonic electronic modular switching system Telephone User Manual
Contents
1. anasonic Proprietary Telephone for Electronic Modular Switching System MODEL NO X 1 7030 Vy ll Vy Le a ii A 7 i m a pe P E n lllustrated Model White KX T7030 is compatible with all of the Panasonic Electronic Modular Switching Systems and can perform most functions within each system Please read before use Important Safety Instructions When using your telephone equipment basic safety precautions should always be followed to reduce the risk of fire electric shock and injury to persons including the following 1 Read and understand all instructions Follow all warnings and instructions marked on the product Unplug this product from the wall outlet before cleaning Do not use liquid cleaners or aerosol cleaners Use a damp cloth for cleaning Do not use this product near water for example near a bath tub wash bowl kitchen sink or laundry tub in a wet basement or near a swimming pool Do not place this product on an unstable cart stand or table The product may fall causing serious damage to the product Slots and openings in the cabinet and the back or bottom are provided for ventilation to protect it from overheating these openings must not be blocked or covered The openings should never be blocked by placing the product on the bed sofa rug or other similar 10 surface This product should never be placed near or over a radi2. Kingdom PQQX6425YA FO0291R071R
3. rain or water during an electrical storm D If the product does not There may be a remote risk of operate normally by electric shock from lightning following the operating instructions Adjust only 13 Do not use the telephone to those controls that are report a gas leak in the covered by the operating vicinity of the leak instructions because improper adjustment of SAVE THESE other controls may result in damage and will often INSTRUCTIONS require extensive work by a qualified technician to Included accessories Handset one Card holder with memory station card one Thank you for purchasing the Panasonic Telephone Table of Contents Important safety instructions 1 CONDECION sirare etea iaraa wa Mw ee ee cadet ote ty ag 3 IIAP Setting a eranen aean ae AE 4 Location of controls 0 00 eee eee 5 USING overlay aeir cerren eont e kie EEE Rea ss 7 installing the card holder nnana nananana 8 Wall mounting 00 20 eee 9 Important information 05 10 Accessory order information Back cover Connection Connect as shown lt D a lt an Ea LD To the EMSS control unit Initial setting VOLUME HANDSET TO MAX mammam MIN RINGER VOLUME HANDSET HEADSET HIGH 8 OFF Low NORMALe
4. TV technician for help This telephone provides magnetic coupling to hearing aids Important information con eKeep the unit away from heating appliances and electrical noise generating devices such as fluorescent lamps and motors The unit should be kept free of dust moisture and vibration and should not be exposed to direct sunlight e Do not use benzine thinner or the like or any abrasive powder to clean the cabinet Wipe it with a soft cloth e Do not use any handset other than Panasonic handset Accessory order information _ e Replacement parts and accessories are available through your local authorized parts distributor eFor ordering the accessory call toll free 1 800 332 5368 Part No Picture Description Comment KX JO7W B 7 feet KX J15W B Handset cord 15 feet KX J25W B 25 feet For your future reference SERIAL NO DATE OF PURCHASE found on the bottom of the unit NAME OF DEALER DEALER S ADDRESS Panasonic Company Division of Matsushita Electric Corporation of America One Panasonic Way Secaucus New Jersey 07094 Panasonic Company West of America Division of Matsushita Electric Corporation of America 6550 Katella Avenue Cypress California 90630 Panasonic Sales Company PSC Division of Matsushita Electric of Puerto Rico Inc San Gabriel Industrial Park 65th Infantry Avenue KM 9 5 Carolina P R 00630 Printed in United
5. able Feature buttons Flexible Message Waiting Button and Indicator Used for Message Waiting Direct Station Selection or Programmable Feature button FWD DND Button and Indicator Sets or cancels the Cail Forwarding Do Not Disturb feature TRANSFER Button Transfers a cail to any extension PAUSE Button Inserts a pause between the access number and the phone number AUTO DIAL STORE Button and Indicator Used for dialing the system speed dialing For storing functions into memory 4 AUTO ANSWER MUTE Button and Indicator Used for answering an intercom call automatically For muting your voice in hands free mode SP PHONE Button and Indicator Used for making or receiving a call without using the handset HOLD Button Places a call on hold These functions are limited to the specified EMSS Control Units Refer to the manual Using overlay When you set the system programming data the function of the KX T7030 connected to your EMSS unit will change as follows SECRET MESSAGE gt CLEAR TRANSFER PAUSE STORE AUTO SELECT AUTO DIAL STORE AUTO ANSWER MUTE SP PHONE NEXT FLASH END Installing the card holder 1 Line up the marks gt on the card holder and ones on the slide rails of the unit 2 Push the two shaded portions slightly and insert the edges of the holder under the slide rails and then slid
6. ator or heat register This product should not be placed in a built in installation unless proper ventilation is provided Do not allow anything to rest on the telephone cord Do not locate this product where the cord will be abused by persons walking on it Do not overload wall outlets and extension cords as this can result in the risk of fire or electric shock Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage points or short out parts that could result in a risk of fire or electric shock Never spill liquid of any kind on the product To reduce the risk of electric shock do not disassemble this product but take it to a qualified serviceman when some service or repair work is required Opening or removing covers may expose you to dangerous voltages or other risks Incorrect reassembly can cause electric shock when the appliance is subsequently used 11 Unplug this product from the restore the product to wall outlet and refer servicing normal operation to qualified service personnel E If the product has been under the following conditions dropped or the cabinet has been damaged A When the power supply F If the product exhibits a cord or plug is damaged or distinct change in frayed performance B If liquid has been spilled into the product 12 Avoid using a telephone C If the product has been other than a cordless type exposed to
7. e down toward arrow A Removing the card holder Push the card holder toward arrow B while keeping the tip of the holder pulled toward arrow C Wall mounting This unit can be mounted on the wall phone plate 1 Turn the handset hook Place the stand on the upside down center of the unit Mount the unit on the wall phone plate Rotate the stand 1 2 turn so To temporarily place the handset that the arrow on the stand down during a conversation hook shows UP for WALL as shown Important information If there is any trouble disconnect the unit from the extension line and connect a known working phone If the known working phone operates properly have the defective phone repaired by one of the specified Panasonic Factory Service Centers If the known working phone does not operate properly check the Electronic Modular Switching System and the Internal extension wiring WARNING TO PREVENT FIRE OR SHOCK HAZARD DO NOT EXPOSE THIS PRODUCT TO RAIN OR ANY TYPE OF MOISTURE CAUTION To assure continued compliance with FCC rules do not make any unauthorized modifications When programming emergency numbers and or making test calls to emergency numbers 1 Remain on the line and briefly explain to the dispatcher the reason for the call before hanging up 2 Perform such activities in the off peak hours such as early morning hours or late even
8. ings INSTALLATION 1 Never install telephone wiring during a lightning storm 2 Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations 3 Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at ihe network Interface 4 Use caution when installing or modifying telephone lines 10 NOTE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio
9. s HIGH HANDSET VOLUME Selector To adjust the volume level of the handset NORMAL Normal voice HIGH Loud voice RINGER VOLUME Selector To adjust the volume level of the ringer HIGH Loud ringer LOW Low ringer OFF No ringer VOLUME Control To adjust the volume level of the speaker volume MAX Loud voice MIN Low voice TO EMSS ee CONTRAST MEMORY HIGH e LOW HANDSET HEADSET SET e PROGRAM i MO MEMORY Switch Set to SET For station programming set to PROGRAM HANDSET HEADSET Selector Set to HANDSET For connecting the headset set to HEADSET CONTRAST Selector To adjust the contrast of the Liquid Crystal Display 4 Location of controls KX T7030 is compatible with the Panasonic Electronic Modular Switching Systems and can perform most functions within each system INTERCOM Button and Indicator Used for making or receiving an intercom call CONFERENCE Button and Indicator Used for speaking with three parties at the same time REDIAL Button Redials the last number dialed FLASH Button Used for sending the hook flash signal to the CO line LCD Liquid Crystal Display Programmable Feature Buttons Dials or accesses the system feature with one touch Flexible CO Line Buttons and Indicators Used for dialing via CO line Direct Station Selection or Programm
Download Pdf Manuals
Related Search