Panasonic AW-PB506AL Camera Accessories User Manual
Contents
1. 70 to 110 Safety zone 1 2 3 4 5 OFF EVF output Y CVBS Weight and dimensions indicated above are approximate Specifications are subject to change without notice 162. ITEM UP switch ITEM DOWN switch DATA YES UP switch DATA NO DOWN switch 11 Setting and changing of menu items 2 Select Option Card 1 to display the submenu When performing the settings with the convertible camera Press the MENU or ITEM AWC switch to move the flashing to the setting item then press the YES ABC switch to display the submenu When performing the settings with the remote control unit AW RC600 Press the ITEM UP or ITEM DOWN switch to move the flashing to the setting item then press the DATA YES UP switch to display the submenu Select the setting item and change the setting When performing the settings with the convertible camera Press the MENU or ITEM AWC switch to move the flashing to the desired setting item then press the YES ABC or NO BAR switch to change the setting When performing the settings with the remote control unit AW RC600 Press the ITEM UP or ITEM DOWN switch to move the flashing to the desired setting item then press the DATA YES UP or DATA NO DOWN switch to change the setting 12 E 4 Return to filming mode When performing the settings with the convertible camera Press the MENU or ITEM AWC switch and select End on the main menu then press the YES ABC switch When performing the settings with the remote control unit AW RC600 Set the MENU switch to OFF After being returned to filming mode the convertible camera will o
3. in which the SDI card has been installed on the interface bracket Fasten the fixing knob to firmly secure the camera 3 Mount the mounting base that is supplied to the viewfinder onto the top of the interface bracket using the 2 screws provided Mount the base securely so that it is not unsteady Mounting base 2 screws 4 Slide the viewfinder onto the mounting base and tighten the fixing knob to secure it firmly 5 Connect the viewfinder cable to the EVF connector 1 or 2 on the interface bracket 6 Connect the EVF I F cable from the interface bracket to the EVF I F connector on the SDI card lt WV VF65B AW VF80 etc gt Connections configuring a system with the remote control unit Convertible camera Inter communications headset AW E350 AW E650 AW E655 Video monitor AW E750 AW E860 etc SDI monitor Viewfinder WV VF65B AW VF80 AW VF64 etc Use the RCU cable AW CA50A26 to connect the remote control unit to the convertible camera Power to the camera is supplied from the remote control unit Remote control unit WV RC700A WV RC550 AW RC600 etc Viewfinder WV VF65B AW VF80 AW VF64 etc Convertible camera AW E350 AW E650 AW E655 SDI monitor AW E750 AW E860 etc SDI output Coaxial cable BBC No PSF1 2M BELDEN 8281 or equivalent coaxial cable max 200 m Remote control unit RCU WV RC700A WV RC55
4. 0 Video monitor 600 etc Composite signals Coaxial cable RCU cable AW CA50A26 Connections When configuring a system with the remote operation panel Convertible camera Use the control cable AW CA50T8G to AW E350 AW E650 AW E655 connect the remote operation panel to AW E750 AW E860 etc the convertible camera Viewfinder Use the AW PS505A AC adapter which 65 AW VF80 AW VF64 etc is an optional accessory for the power supply Remote operation panel AW CB400 etc Inter communication between the remote operation panel and studio SDI Video monitor card is not possible SDI monitor Viewfinder WV VF65B AW VF80 AW VF64 etc TALLY cable Convertible camera AW E350 AW E650 AW E655 AW E750 SDI monitor AW E860 etc Coaxial cable SDI output BBC No PSF1 2M BELDEN 8281 or equivalent coaxial cable max 200 m AC adapter AW PS505A Video monitor Cable provided with AC adapter Remote operation panel AW CB400 etc 10BASE T straight cable AC adapter 1 Control cable AW PS505A 0 AW CA50T8G 10 E Setting and changing of menu items Camera settings to match the system configuration and filming conditions can be made using the menu screens See the convertible camera operating instructions for more information on the settings For details on the set
5. 0S bracket makes it possible for a viewfinder AW E600 AW E800 AW E800A and or inter communications headset to AW RP605 AW PB605 be used and thus enable the camera to When the SDI card unit is to be be used as a studio camera In addition discarded at the end of its service there are two signal outputs for SDI signals life ask a specialized contractor compliant with EBU Tech 3267 E standard to dispose of it properly in order to L protect the environment Characteristics Two signal outputs for SDI signals Output signals brightness and compliant with the EBU Tech 3267 E composite video signals to the standard BBC No PSF1 2M BELDEN viewfinder can be switched using the 8281 or equivalent coaxial cable max menu settings 200 m EDH Error Detection and Handling flags complying with the SMPTE RP165 standard can be added A switch can be used to enable or The VIDEO ON OFF switch function of disable the addition of these flags the viewfinder AW VF64 is incorporated In order to prevent CRT burn in the AW VF64 does not come with a standby e Zebra pattern and safety zone displays appearing in the viewfinder can be switched using the menu settings An inter communications headset can be used and its volume adjusted function The STANDBY ON switch function of the viewfinder WV VF65B AW VF80 is incorporated Precautions for use When connecting or disconnecting a Avoid using the unit
6. Panasonic Operating instructions Studio SDI Card AW PBS06AL This product consists of an SDI card and an interface bracket 2 lt LL ITALIANO p 2 2 2 2 N Before attempting to connect operate or adjust this product please read these instructions completely ENGLISH VERSION Safety precautions DO NOT REMOVE PANEL COVERS BY UNSCREWING To reduce the risk of electric shock do not remove the covers No user serviceable parts inside Refer servicing to qualified service personnel WARNING e TO REDUCE THE RISK OF FIRE OR SHOCK HAZARD DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE eTO REDUCE THE RISK OF FIRE OR SHOCK HAZARD KEEP THIS EQUIPMENT AWAY FROM ALL LIQUIDS USE AND STORE ONLY IN LOCATIONS WHICH ARE NOT EXPOSED TO THE RISK OF DRIPPING OR SPLASHING LIQUIDS AND DO NOT PLACE ANY LIQUID CONTAINERS ON TOP OF THE EQUIPMENT CAUTION TO REDUCE THE RISK OF FIRE OR SHOCK HAZARD AND ANNOYING INTERFERENCE USE THE RECOMMENDED ACCESSORIES ONLY CAUTION TO REDUCE THE RISK OF FIRE OR SHOCK HAZARD REFER CHANGES OF SWITCH SETTINGS INSIDE THE UNIT TO QUALIFIED SERVICE PERSONNEL indicates safety information Information on Disposal for Users of Waste Electrical amp Electronic Equipment private households This symbol on the products and or accompanying documents means that used electrical and electronic products should not be mixed with general househ
7. en configuring a system 1 Characteristics 4 emote 2 Setting and changing of menu items 11 Precautions fOr USE 4 Performing the Settings 14 Major operating controls and M Optional card settings submenu 13 RI EATEN 14 5 re 6 501 14 Interface bracket 15 Te Specifications 16 Interface bracket mountings 8 Mounting the bracket on a tripod 8 Mounting the camera 8 Mounting the viewfinder 8 Configuration SDI AW PB506A U01 1 Interface bracket 506 U02 1 Accessories Adjuster plug M6 1 Screws 6 MM 5 2 5 81011 4 Introduction Installing the SDI card in a convertible Notes camera such as the AW E350 AW E650 AW PB506A cannot be installed AW E655 AW E750 and AW E860 and to the following models mounting the camera on the interface AW E300 AW E300A AW E30
8. in very humid cable from any unit ensure that the dusty locations as this may cause it to power to that unit is turned off malfunction Do not drop this product or subject it to Avoid using the product at a cold place strong shock or vibration as this may below 10 C or at a hot place above cause it to malfunction 45 C because extremely low or high temperature will adversely affect the parts inside 4 E Major operating controls and their functions ESDI card EVF I F connector EVF I F 2 Model selection lt E350 E860 gt The EVF I F cable from the interface Factory setting E350 bracket is connected here When the AW E350 AW E650 AW E655 or AW E750 is used set SDI output 1 2 connector this switch at the E350 SDI OUT 1 2 When the AW E860 is used set this SDI signals are output from here switch at the E860 3 DATA CLIP lt NORMAL CLIP gt Factory setting NORMAL At the NORMAL setting signal input is output at the same level at which it was input At the CLIP setting signal input at less than 0 is output at 0 and signal input at more than 100 is clipped at 100 Setting switches E350 E860 DATA CLIP NORMAL CLIP 4 NTSC PAL switching lt NTSC PAL gt 4 NTSC PAL NTSC Factory setting NTSC Leave this switch at the factory setting 1 EDH lt ENABLE DISABLE gt Factory setting ENABLE An EDH flag is added to SDI output at the ENABLE se
9. nnector Installing the SDI card Always ask your local dealer to install the SDI card Before installing the SDI card Release the static carried in the body of the person to perform the installation Installation can be performed more safely if an anti static wrist strap is worn Touching the card without first releasing this static may cause malfunctioning Do not allow the metal part of the card come in contact with any other metal parts Rear panel Wa GIL IN 1 wi 2 yorBAR uT 0 yp RENOTE Ne Optional card slot cover 4 screws 8 mm 1 Turn the power to the camera off 5 Firmly tighten the 2 screws 6 mm to and remove any cables which are the optional card slot connected to the power connector or 6 other connectors Firmly secure the rear panel with the 4 screws 8 mm 2 Loosen the 4 screws 8 mm on the rear panel of the camera then remove Note the panel itself If the screws are misplaced use the extra screws supplied with this 3 Loosen the 2 screws 6 mm on the product optional card slot cover then remove the cover 4 Align the SDI card with the guides and insert it Ensure the card is fully inserted Interface bracket mountings Mounting the viewfinder on a bracket Mounting the bracket on a tripod 1 Mount the interface bracket on the tripod Screw 1 4 2OUNC Mounting the camera 2 Mount the camera
10. old waste For proper treatment recovery and recycling please take these products to designated collection points where they will be accepted on a free of charge basis Alternatively in some countries you may be able to return your products to your local retailer upon the purchase of an equivalent new product Disposing of this product correctly will help to save valuable resources and prevent any potential negative effects on human health and the environment which could otherwise arise from inappropriate waste handling Please contact your local authority for further details of your nearest designated collection point Penalties may be applicable for incorrect disposal of this waste in accordance with national legislation For business users in the European Union If you wish to discard electrical and electronic equipment please contact your dealer or supplier for further information Information on Disposal in other Countries outside the European Union This symbol is only valid in the European Union If you wish to discard this product please contact your local authorities or dealer and ask for the correct method of disposal Contents 3 2 sa 9 50 85 spa 3 mney with the remote control unit 9 4 MWh
11. perate as per the changed settings Setting and changing of menu items Optional card settings submenu xOption Card Set Level 90 Safety Zone 1 Output Return Zebra indicator ON OFF This sets the zebra pattern display which appears in the viewfinder ON Zebra patterns are displayed in the viewfinder OFF Zebra patterns are not displayed in the viewfinder lt Note gt Even if ON is selected for this setting the zebra patterns will not be displayed in the viewfinder if CVBS has been selected as the EVF output setting Level 70 to 110 The zebra patterns are displayed to use as a yardstick for the brightness level lt Note gt These settings are available when has been selected for the Zebra indicator setting Safety zone 1 to 4 OFF This selects the type of safety zone that is displayed in the viewfinder If OFF is selected a safety zone will not be displayed lt Note gt The safety zone and the center marker reflect the electrical positions which may differ from the optical positions 1 2 3 t 4 5 E L 4 L 2 The inner frame and the outer frame are approximately 90 and 95 respectively of the safety zone O EVF output Y CVBS This sets the signals to be output to the viewfinder y Brightness signals are output to the viewfinder CVBS Color signals are outpu
12. t to the viewfinder lt Note gt The zebra pattern is not displayed in the viewfinder when CVBS has been selected 13 Appearance ESDI Unit mm 14 Appearance interface bracket Unit mm Specifications Power requirements Power consumption indicates safety information DC 12 V supplied from convertible camera 15 W When WV VF65B AW VF80 is connected Ambient operating temperature 10 C to 45 C Ambient operating humidity Dimensions WxHxD SDI card Interface bracket Weight SDI card Interface bracket Input output connectors SDI card SDI OUT 1 2 connector EVF I F connector Interface bracket EVF connector 1 EVF connector 2 Inter communications jack TALLY input connector Switch control functions SDI card Interface bracket Menu screens 30 to 90 without condensation 21 5 70 92 mm excluding protrusions 190 183x171 mm excluding protrusions 0 10 kg 1 06 kg BNC compliant with EBU Tech 3267 E standard 10 pin round 10 pin round composite signals brightness 1 0 V P P 6 pin round composite signals brightness 1 0 V P P BNC EDH ENABLE DISABLE Model selection E350 E860 DATA CLIP NORMAL CLIP NTSC PAL switching NTSC PAL EVF standby VIDEO ON OFF switch WV VF65B AW VF80 5 AW VF64 VIDEO ON VIDEO OFF Inter communications level control Zebra indicator ON OFF Level
13. ting procedures when the remote control unit and remote operation panel are used refer to the operating instructions of the unit and panel Performing the settings 1 Display the main menu When performing the settings with the convertible camera Press the MENU switch continuously for at least 5 seconds When performing the settings with the remote control unit AW RC600 Set the MENU switch to ON Main menu for halogen light mode fluorescent light mode and outdoor mode The mode selected is displayed here xHalogen Light Mode Brightness Set Color Set G L Color Bar Set Color Sharpness DTL Set Other Set Option Card 1 Initialize Data End To return to filming mode This is displayed when the convertible camera is used to perform the settings Main menu for user mode xUser Mode Setx x Iris Shutter Gain Set Color Set G L Color Bar Set Detail Setl Detail Set2 Color Matrix Set Other Set1 Other Set2 Option 1 Initialize Data End Option Card 2 is displayed on the menu when the optional card has been plugged into the optional card slot of the additional card box Convertible camera OPTION CARD VIDEO OUT VF REMOTE MENU switch ITEM AWC switch YES ABC switch NO BAR switch Remote control unit AW RC600 MENU switch CAMERA SET UP NU 4 m DPA 7 UP DOWN YES UP NO DOWN
14. tting Major operating controls and their functions Winterface bracket O EVF connector 1 EVF1 The viewfinder WV VF65B AW VF80 is connected here O EVF connector 2 EVF2 The viewfinder AW VF64 is connected here Note Do not connect EVFs to connectors 1 and 2 and at the same time EVF standby VIDEO ON OFF switch ST BY VIDEO ON OFF lt For the WV VF65B AW VF80 gt ST BY Places the viewfinder in standby mode ON Outputs images to the viewfinder lt For the AW VF64 gt VIDEO ON Outputs images to the viewfinder VIDEO OFF No images appear on the viewfinder AW VF64 does not come with a standby function Inter communications level control LEVEL This adjusts the sound level output to the inter communications headset Inter communications jack M3 INCOM The inter communications headset is connected here If the plug diameter does not match use the adjuster plug M6 supplied with this product MIC Dynamic With Preamp 50 20 dB Receiver 150 max 200 mW EVF I F cable This is connected to the EVF I F connector on the SDI card TALLY input connector TALLY IN This is the tally control external input connector OPEN TALLY OFF SHORT TALLY ON When using the AW CB400 remote operation panel and AW CA50T8G control cable for connecting to the convertible camera connect the TALLY cable of the AW CA50T8G to this co
Download Pdf Manuals
Related Search