Numark Industries DM2000X DJ Equipment User Manual
Contents
1. disconnect it s cable Re attach the new crossfader and screw the mounting plate back onto the unit you re back in business 8 The Crossfader Control toggle allows the DJ either reverse the direction of the crossfader or turn it off By reversing direction Channel 3 will be on the left and Channel 2 will be on the right 9 Transform Buttons are for quickly reversing the crossfader direction in order to create various special effects 10 Beat indicator lights show peaks in the music that usually represent a strong drum beat You can use these to help you try and match up beat mixes MASTER BOOTH OUTPUT SECTION 11 The Stereo Master Fader controls the overall output level 12 The Booth Level controls speaker volume for a remote zone or booth monitors If you do not use booth monitors the output can feed a tape deck another amplifier another mixer or a satellite soeaker system Note This can also be used to supply line level audio to a lighting controller or to lights that are sound activated CONTRACTOR S NOTE Booth Level provides zone control in installations where there are two separate rooms or a bar and dance floor for example Remote zone volume should be controlled from the DM2000X DM2000X 13 Stereo Output Level Indicator This fast accurate stereo meter tracks the output level It s OK to be occasionally in the red as long as 5dB or 8 aren t constantly lit Set the crossover equalize2. the grounding lug for turntables 1 2 and 3 phono inputs on Channels 1 2 and 3 Always use this connection your turntable cable should have a grounding wire 3 The Stereo Main Outputs are low impedance RCA connectors controlled by the Master fader 4 The Stereo Booth Zone Outputs are low impedance unbalanced RCA jacks controlled by the Zone Level control 5 Send Output is set by the send buttons pressed on the front panel Hook up you sampler or other processor here 6 Channels 2 and 3 Line Inputs are unbalanced RCA jacks The Line Input is selected with the toggle switch on the front panel You can connect stereo audio from HiFi VCRs cassette and reel to reel tape decks DAT machines CD players laser discs tuners even synthesizers or other mixing consoles NOTE Plug mono audio sources into both Left and Right inputs using a Y cable connector 7 Phono Inputs on Channels 1 2 and 3 use unbalanced RCA jacks Your input signal is fed directly to the DM2000X s high quality RIAA phono pre amplifiers so use this position only for moving magnet cartridges Line level sources will overload the sensitive phono pre amps and will sound very bad so always be sure to toggle the line phono switch over to line before connection of line sources 8 Line Phono Input switch Use this to allow line level equipment to be plugged into your phono inputs giving you a total of 5 line input options Numark The Proven Leader
3. to the PFL channel This allows the DJ to accurately match levels before mixing with that channel s gain control The idea is to properly match inputs not the input with the output 6 17 5 ep 8 12 2 11 10 15 14 4 Buttons for allowing channels pre fader output to be sent to the send connectors in the rear of the unit These are used for sampling and other special effects You would return the send signal through another input channel 5 Treble Mid and Bass Controls are for setting appropriate equalized levels for the music you are playing When turn all the way left they CUT the signal by 30dB for special effects mixing 6 Gain Controls are for accurately matching audio levels of the channels Numark The Proven Leader in Technology 6 http www numark com CROSSFADER SECTION 7 The Replaceable Crossfader achieves clean segues between the two selected input channels Hard left selects Channel 2 Hard right selects the Channel 3 With the crossfader centered both channels are live Use the crossfader for fast and seamless segues from one selected channel to the other Note The crossfader is user replaceable in case of failure Simply unscrew the two large screws which hold it in place lift it out and
4. MATION Please read this entire manual before connecting the DM2000X to your system For optimum performance Always make sure that AC power is OFF while making any connections Do not use excessively long cables i e over 50ft 14m Be sure plugs and jacks are tightly mated Loose connections can cause hum noise or intermittents that could easily damage your speakers Never use spray cleaners the slide controls Residues cause excessive dirt build up and this will void your warranty In normal use slide controls can last for many years If they malfunction usually because of a dirty or dusty environment consult a professional technician Never attempt to make any adjustments or repairs other than those described in this manual Take the DM2000X to your dealer or to an authorized Numark Service Center A NOTE ON CABLES Make the input and output connections with readily available low capacitance stereo cables Quality cable makes big difference in audio fidelity and punch See your Numark dealer or electronics audio specialist store if you are not sure which cables to get DM2000X SYSTEM PRECAUTIONS Use appropriate cables throughout your system Quality shielded audio cables and terminated shielded video cables low capacitance preferred Speaker cables must be 14 gauge minimum 12 or 10 gauge is better e Reliability will be enhanced through the
5. Numark Professional Disc Jockey Products DM2000X STEREO MIXER OWNER S MANUAL DM2000X PRO MASTER MIX yu TRANSFORM TRANSFORM a NUMARK INDUSTRIES 11 Helmsman Road North Kingstown RI 02852 http www numark com DM2000X Safety Information and Product Registration CAUTION N RISK OF ELECTRIC SHOCK A N DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE ANY COVER NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL ONLY The lightning flash with arrowhead symbol within the equilateral triangle is intended to alert the user to the presence of un insulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons The exclamation point within the equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying this appliance CAUTION FOR USA amp CANADIAN MODELS ONLY TO PREVENT ELECTRIC SHOCK DO NOT USE THIS POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN FULLY INSERTED TO PREVENT BLADE EXPOSURE SAFETY INSTRUCTIONS 1 Read Instructions All the safet
6. ational Inc hereafter Numark warrants each new product manufactured and or supplied by it to be free from defects in material or workmanship under conditions of normal use and service for 360 days beginning on the date of purchase from an authorized Numark Dealer but not to exceed 2 years from date of shipment by Numark The Numark obligation under this warranty is limited to repairing or replacing at its option the product or part s therein which upon examination by Numark shall appear to be defective or not up to factory specifications providing the Numark product is returned transportation prepaid to Numark Numark shall not be liable for any damages consequential or otherwise resulting from the use and operation of this product and makes no other warranty s either express or implied on this product including any warranty of merchantability This warranty does not extend to any of our products which have been subjected to misuse neglect accident incorrect wiring not our own improper installation or use in violation of instructions furnished by us nor extended to units which have been repaired or altered outside of our factory nor to cases where the serial number thereof has been removed defaced or changed nor to accessories used therewith not of our own manufacture Numark reserves the right to make changes or improvements in its products during subsequent production without incurring the obligation to install such chang
7. entire manual before you begin operation If you are an experienced DJ simply replace your old mixer The DM2000X can be 10 rack mounted or used as a free standing unit Keep in mind that there are few features you may never have seen before in a mixer of this type that you will need to read about INSTALLATION AND OPERATION Study the Connections Diagram on page 13 First connect all stereo input sources Next connect your microphone s and monitor headphones Make sure all faders are at zero and the unit is off Finally connect the stereo outputs to the power amplifier s and or audio sources Plug the DM2000X into AC power Now you are ready to switch it on CHANNEL FEATURES 1 Channels 1 2 amp 3 Rotatable Input Toggle Switches select which source will be live to that channel based on what you have connected to the rear panel input section To rotate or replace the toggle a Turn off all power b Remove corner screws c To rotate lift of toggle and place in it s new position or to replace unplug the old unit and plug in the new one d Screw toggle back into place 2 The Input Faders are low noise low impedance high quality smooth Alps faders These control individual source levels in the mix 3 PFL and Channel Cue Assign The PFL pushbuttons are used to route channel audio to the main volume meter and the Cue Monitor Section When a PFL is pressed the main volume meter changes its display
8. es or improvements on previously manufactured equipment To place this warranty into effect the enclosed WARRANTY REGISTRATION CARD must be returned to Numark Industries LLC within thirty 30 days after date of purchase This warranty gives you specific legal rights and you may also have other rights which vary from state to state Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation or exclusion may not apply to you EQUIPMENT TRANSPORT A Return Authorization number should be obtained from Numark through the addresses or phone numbers below It is the customer s obligation when returning faulty equipment to properly pack the Numark equipment in its original packaging Failure to do so may inadequately protect the equipment in transit and therefore jeopardize the customer s warranty The defective Numark equipment should be sent FREIGHT PREPAID with Return Authorization number to NUMARK INDUSTRIES 11 Helmsman Road Telephone 1 401 295 9000 North Kingstown RI 02852 U S A Fax 1 401 295 5200 Attention Service Department E mail numark numark com
9. in Technology 1997 Numark Industries 8 http www numark com DM2000X DM2000X CONNECTION DIAGRAM Turntable 3 Turntable 2 Turntable 1 Numark The Proven Leader in Technology 1997 Numark Industries 9 http www numark com DM2000X SPECIFICATIONS Inputs Line 10Kohm input impedance 100mV rms sensitivity for 1 22V output Mic 10 Kohm input impedance unbalanced 3mV rms sensitivity for 1 22V output 50mV rms max input Phono 47Kohm input impedance 1 5mV rms sensitivity 1KHz for 1 22V output Outputs Line 9V rms max 20dBm Headphone 0 5W into 47 Distortion less than 0 01 Signal to Noise Ratio vs maximum output Line Better than 90dB Mic Better than 84dB Phono Better than 80dB Frequency Response Mic 20Hz 15 KHz 0 5dB Line 20Hz 20 KHz 0 5dB Phono 1dB except for controlled attenuation of 3dB 20Hz to reduce rumble and feedback Channel EQ Bass 15 30 dB 40 Hz Middle 15 30 dB 1 36 KHz Treble 15 30 dB 20 Hz Power Consumption 15 watt typical 18 watt with full headphone output Numark The Proven Leader in Technology 1997 Numark Industries 10 http www numark com DM2000X BLOCK DIAGRAM Numark The Proven Leader in Technology 1997 Numark Industries 11 http www numark com Numark Professional Disc Jockey Products Warranty and Service Information Numark Industries LLC and Numark Intern
10. nding or polarization means built into the mixer is not defeated 12 Internal External Voltage Selectors Internal or external voltage selector switches if any should only be reset and re equipped with a proper plug for alternative voltage by a qualified service technician Do not attempt to alter this yourself NOTE This apparatus does not exceed the Class A Class B whichever is applicable limits for radio noise emissions from digital apparatus as set out in the radio interference regulations of the Canadian Department of Communications WARNING To reduce the risk of fire or electric shock do not expose this appliance to rain or moisture Electrical equipment should NEVER be kept or stored in damp environments Please record the serial number ot your unit as Shown on the back of the chassis as well as the name dealer from whom you purchased the unit Retain this information for your records Please return the warranty card enclosed to register your mixer with us IMODEL DM2000X PURCHASED FROM SERIAL NUMBER DATE OF PURCHASE Numark The Proven Leader Technology 1997 Numark Industries 2 http www numark com DM2000X NUMARK DM2000X STEREO MIXER INDEX Safety Information Page 3 Product Registration Introduction Page 5 Features Precautions Page 6 Front Panel Diagram Page 7 Operating Instructions Rear Panel Diagram Page 8 Connection Diagram Page 9 Specification
11. r and power amp inputs to avoid distortion at each step in the audio chain Proper attention to the meter results in the punchiest possible sound without audible distortion This meter is also used to monitor the PFL CUE section When a PFL LED is lit the display indicates this channel when the MASTER LED is lit then the Master output is shown CUE SECTION 14 The CUE section includes the Program Mix PGM control the Headphone Volume control and the Headphone Connector located on the front of the unit Connect headphones with a standard 1 4 stereo plug The PF L audio is sent to the headphone amp using the PFL Assign Pushbutton and the PGM Mix control The Program Mix controls the amount of program audio in the headphones so that beats can be matched exactly and segues are smooth when a song is cued MIC SECTION 15 The MIC Connector is located on the front panel of the unit and is controlled through an input on Channel 1 16 12V BNC Connector allows a 12 volt gooseneck lamp to be connected directly to the mixer This light is readily available from your Numark dealer 17 Power Switch and Power On LED Numark The Proven Leader in Technology 1997 Numark Industries 7 http www numark com DM2000X DM2000X REAR PANEL DIAGRAM REAR PANEL INPUTS AND OUTPUTS 1 AC Connection Plug your power cord in here See safety precautions on page 3 for proper treatment of the power cord 2 GND is
12. s Page 10 Block Diagram Page 11 Warranty and Service Page 12 Numark The Proven Leader in Technology 1997 Numark Industries 3 http www numark com DM2000X CONGRATULATIONS You have purchased the DM2000X PRO MASTER MIX Stereo Mixer by Numark This equipment features a completely new design and the latest in manufacturing technology to give you greater quality and better reliability than ever before The DM2000X has been designed by Dus for Djs It s is the Scratch Mixers Dream Machine with absolute total mix and effect control Enjoy your new mixer and remember BE CREATIVE Thank you for buying Numark DJ products FEATURES Rotatable Input Select Toggles Crossfader Reverse switch 3 Phono Inputs with low noise RIAA preamps 5 Line Inputs DJ Mic Input Bass Mid amp Treble controls on each channel with Cut ability on each control for special effects and creative mixing Individual Gain Controls on each channel User replaceable crossfader Transform buttons on Channels 2 and 3 Monitor Zone Level Control Pushbutton Cueing with PFL pre fader level on each channel Send on each channel for easily hooking up an external sampler Same height as TT1700 and TT1910 turntables Only 9 5 24 cm wide Console inclined to raise above tone arm Rugged construction 12V BNC light connector Numark The Proven Leader in Technology 1997 Numark Industries 4 http www numark com IMPORTANT INFOR
13. use of banana connectors on the speaker wires Observe correct speaker wire polarity If in doubt consult your Numark dealer or a qualified technician care to connect only one cable at a time Pay attention to the color coded labelled Input and Output jacks ALWAYS remember TURN AMPS ON LAST AND OFF FIRST Begin with master faders volume controls on minimum and the amplifier gain input control s down Wait 8 to 10 seconds before turning up the volume This prevents transients which may cause severe speaker damage Use restraint when operating controls Try to move them slowly Rapid adjustments could damage speakers due to amplifier clipping Avoid amplifier clipping at all costs this occurs when the red LEDs usually on the front panel of most professional power amplifiers start flashing Clipping is when the power amplifier is distorting and working beyond it s limits Amplifier distortion is THE major cause of speaker failure To prevent fire or shock hazard do not expose the unit to rain or moisture Never place cans of beer soda glasses of water or anything wet on top of the mixer Numark The Proven Leader in Technology 1997 Numark Industries 5 http www numark com 1997 Numark Industries DM2000X DM2000X FRONT PANEL DIAGRAM GUIDED TOUR OF FEATURES AND OPERATING INSTRUCTIONS If the DM2000X is your first mixer please read this
14. y and operating instructions should be read before this product is connected and used 2 Retain Instructions The safety and operating instructions should be kept for future reference 3 Heed Warnings All warnings on this product and in these operating instructions should be followed 4 Follow Instructions All operating and other instructions should be followed 5 Water and Moisture This product should be kept away from direct contact with liquids 6 Heat Avoid placing this product too close to any high heat sources such as radiators 7 Power Sources This product should be connected to a power supply only of the type described in these operating instructions or as marked on the unit 8 Power Cord Protection Power supply cords should be routed so that they are not likely to be walked upon or pinched by items placed on or against them When removing the cord from a power outlet be sure to remove it by holding the plug attachment and not by pulling on the cord 9 Object and Liquid Entry Take care that objects do not fall into and that liquids are not spilled into the inside of the mixer 10 Damage Requiring Service This product should be serviced only by qualified personnel If you have any questions about service please contact Numark at the number s shown on the back cover of this manual 11 Grounding or Polarization Precautions should be taken so that the grou
Download Pdf Manuals
Related Search