Monarch 1071-4860-122 Automobile Parts User Manual
Contents
1. VA OUT COM VA_ OUT COM e Oo oo e ee6 LOAD oN pe 5000 ap ig gt SUPPLY MAX w CURRENT OUTPUT CURRENT OUTPUT INTERNAL SOURCE EXTERNAL SOURCE Figure 4 Current Output Option Connections NOTE The voltage source you use will determine the maximum resistance of the load This voltage is referred to as the compliance voltage and must be equal to the maximum current through the load 20 mA multiplied by the load resistance plus 4 Vdc For example if the load is 1000 ohms the external voltage source must be 1000 ohms x 0 020 A 4 Vde 24 Vdc Thus for an external source voltage of 24 Vdc the maximum loop load the sum of all resistances in the loop is 1000 ohms 24 Vdc is in fact a recommended voltage The voltage supplied by an external source should NEVER exceed 40 Vdc The ACT 1B 15 Vdc internal voltage source VA permits a maximum load resistance of 500 ohms If the unit is de powered connect the dc supply Positive to the terminal marked L and the dc supply Negative or Common to the terminal marked N NOTE On dc powered units no connection is required to the terminal marked GND SENSOR CONNECTIONS A speed sensor not included is connected to the terminals under the section labeled INPUT on the rear panel Refer to Figure 2 and 3 Connections and their functions are as follows 5V PX2. Magnetic Monarch M 190W or MT 190W Infrared Monarch IRS 5W Laser Monarch RLS 5W 4 to 20 mA see page 7 for maximum load calculation Full scale RPM settings as specified when ordered 12 bit resolution 4096 steps over the range specified 0 to 5 Vdc 5 mA maximum load Full scale RPM settings as specified when ordered 12 bit resolution 4096 steps over the range specified 0 to 5 V TTL pulse non inverting one pulse out for each pulse in ACCESSORIES SENSORS ROS 5W T 5 P5 11 M 190W MT 190W IRS SW RLS 5W Remote Optical Sensor Reflective Tape 5 foot 1 5 m roll 0 5 inch 10 mm wide Proximity Sensor Magnetic Sensor Magnetic Sensor with Amplifier Module Infrared Sensor Laser Sensor NOTE Standard cable length is 8 feet 2 5 m on all sensors Longer cable lengths of 15 30 50 or 100 feet 4 6 9 2 15 or 30 5 m are optional 10 OPTIONS IO AO PO CAL N LS T 4 to 20 mA current output 0 to 5 Vde analog output NOTE Full scale RPM must be specified for the above options when ordering 0 to 5 V TTL compatible pulse output NOTE Pulses out per revolution equal pulses in per revolution N LS T Traceable Certificate of Calibration OVERVIEW ACT 1B Digital Tachometers display rotational speed directly in RPM ona 5 digit red LED display using a speed sensor providing a single pulse per revolution Model ACT 1B 10 pulses per revolution Model ACT 1B 10 or 60 pulses per re
3. SIG COM Positive 5 Vdc to provide power to optical laser infrared or amplified magnetic sensors Maximum load is 75 mA dc Positive 8 Vdc supply for use with two wire proximity sensors Maximum load for proper operation with two wire sensors is 5 mA Positive input signal from the speed sensor Accepts TTL pulses or ac signals unipolar and bipolar from 1 5 Vac to 50 Vac Contact the factory for increased sensitivity Connect the signal wire from three wire sensors or the positive side of two wire magnetic sensors to this terminal Typical input impedance is 10 Kohms Common or Negative connection for both signal and power from most sensors Refer to Figure 3 for connection of Monarch standard sensors The connections are typical for these types of sensors INPUT 5V PX SIG COM eee 6 INPUT 5V PX SIG COM eee e INPUT 5V PX SIG COM O A Ol S INPUT 5V PX SIG COM eee a WHITE BLACK BROWN BLUE BROWN Se Wai Shield to COM BLARK Shield to COM B M 190W P5 11 ROS 5W OPTICAL SENSOR SHOWN AC or TTL MAGNETIC PROXIMITY RLS 5W LASER SENSO
4. MONARCH INSTRUMENT Instruction Manual MONARCH CE ACT 1B ACT 1B 10 ACT 1B 60 Panel Tachometers 15 Columbia Drive Printed in the U S A Amherst NH 03031 2334 USA Phone 603 883 3390 Monarch Instrument 2001 all rights reserved Fax 603 886 3300 E mail techsup monarchinstrument com 1071 4842 114 Website www monarchinstrument com AN Safeguards and Precautions A Read and follow all instructions in this manual carefully and retain this manual for future reference Do not use this instrument in any manner inconsistent with these operating instructions or under any conditions that exceed the environmental specifications stated Be sure the power supplied to this instrument matches the specification indicated on the rear panel of the instrument Be sure all power is removed before making or removing any connections to or from this instrument For full compliance with CE specifications be sure the appropriate ground connection is made This instrument is not user serviceable For technical assistance contact the sales organization from which you purchased the product or Monarch Instrument directly LIMITED WARRANTY SELLER warrants hardware products to be free from any defect in materials or workmanship for a period of one 1 year from date of shipment to BUYER SELLER s entire liability and BUYER s sole and exclusive remedy resulting from any defect in workmanship or material in the ha
5. R SOURCE SENSOR SENSOR IRS 5W INFRARED SENSOR MT 190W AMPLIFIED MAGNETIC SENSOR Figure 3 Sensor Connections 5 OUTPUT OPTIONS The ACT 1B may be equipped with either a Current Output IO or an Analog Output AO and or a TTL Pulse Output PO NOTE Full scale RPM settings must have been specified when ordered these options are not field programmable The Current or Analog Outputs are connected to the terminals in the section labeled ANALOG OUTPUT OPTION on the rear panel The Pulse Output is connected to the terminals under the section labeled OUT on the rear panel CAUTION The IO or AO COM is NOT isolated from the other COM connections Current Output Option IO The current output is 4 to 20 mA This output is a current sink and requires a source voltage A 15 Vdc internal source is provided at the terminal marked VA When using an external voltage source the current from that source is regulated by the ACT 1B Typical connections are as follows See Figure 4 When using the ACT 1B internal 15 Vdc source connect the Positive side of the load to the terminal marked VA and the other side of the load to the terminal marked OUT When using an external voltage source connect the Negative side of the external source to the terminal marked COM the Positive side of the supply to the Positive side of the load and the other side of the load to the terminal marked OUT
6. SOFTWARE BUYER agrees that any specific right or remedy granted to BUYER hereunder with respect to any breach or default by SELLER shall be in lieu of all other rights and remedies otherwise available to BUYER at law or in equity as the result of such breach or default regardless of whether based on contract tort strict liability or other theory of liability IN NO EVENT SHALL SELLER BE LIABLE FOR ANY SPECIAL INDIRECT INCIDENTAL CONSEQUENTIAL OR PUNITIVE LOSSES OR DAMAGES INCLUDING BUT NOT LIMITED TO LOSSES OR DAMAGES FOR ANY LOST PROFITS OR LOST DATA AS THE RESULT OF ANY BREACH OR DEFAULT BY SELLER WITH RESPECT TO THE HARDWARE OR SOFTWARE EVEN IF SELLER HAS BEEN ADVISED OR MADE AWARE OF THE POSSIBILITY OF ANY SUCH LOSSES OR DAMAGES AND REGARDLESS OF WHETHER THE CLAIM IS BASED ON CONTRACT TORT STRICT LIABILITY OR OTHER THEORY OF LIABILITY This limited warranty does not extend or apply to consumables including but not limited to lamps and batteries if applicable or equipment instruments or accessories which are warranted separately by the original manufacturer of these items DECLARATION OF CONFORMITY As Manufacturer Monarch Instrument Division of Monarch International Inc 15 Columbia Drive Amherst NH 03031 USA declares under Monarch s sole responsibility that the product Name ACT Panel Tachometer Models ACT 1B ACT 1B 10 ACT 1B 60 to which this declaration relates is in conformity with the following st
7. andards EMC EN50082 1 1997 EN50082 2 1995 EN55011 1991 Group 1 Class B and therefore conforms with the requirements of Council Directive 89 336 EEC relating to electromagnetic compatibility The testing of this product was performed by Retlif Testing Laboratories NH in October of 1999 File R 351 4N2 Ahan Oxo Manufacturer Amherst NH Alan Woolfson VP Engineering Authorized Signature 8 October 1999 TABLE OF CONTENTS Specifications OvervieW oo Installation and Power Sensor Connections Output Options Options oo eee Accessories Sensors SPECIFICATIONS Range 5 to 99 999 RPM Accuracy 1 RPM or 0 005 of reading Resolution 1 RPM Display 5 digit 0 56 14 mm high red LED Display Update Twice per second above 120 RPM Dimensions 1 8 DIN by 4 5 114 mm deep Power Supply Inputs Sensor Excitation Recommended Sensors Optical IO Option AO Option PO Option Standard 115 Vac or 230 Vac 10 50 60 Hz Specified when ordering Optional 12 Vdc to 15 Vdc 1 75 Watts Universal input for optical proximity two wire or three wire magnetic infrared or laser Sensors TTL input or 1 5 Vac to 50 Vac input Standard inputs are 1 10 or 60 pulses per revolution depending on the model Contact factory to order customized pulses per revolution 8 Vdc at 5 mA for proximity sensors 5 Vdc at 75 mA for all other sensors Monarch ROS 5W Proximity Monarch P5 11
8. l Refer to Figure 2 below CUTPUT SERIAL OPTION NUMBER O 4 20ma o o sv O CUSTOM POWER ge 024 0230 0115 Ac M con LP N Lt GND Se 6 MODEL ACTIB MADE IN THE USA Figure 2 ACT 1B Rear Panel Ifthe unit is ac powered 115 Vac or 230 Vac connect the Live Hot wire to the terminal marked L and the Neutral Return wire to the terminal marked N Connect the Ground Earth wire to the terminal marked GND NOTE For full compliance with CE specifications the Ground GND connection must be made Analog Output Option AO The analog output is 0 to 5 Vdc Connect the Positive side of the signal to the terminal marked OUT and the Return side of the signal to the terminal marked COM NOTE If your ACT 1B is equipped with either a current output or an analog output the full scale output has been factory preset to the speed range specified at the time of purchase The output is linear in 4096 discrete steps over its designated range Pulse Repeater Output Option PO The Pulse Repeater output provides a conditioned TTL positive going 5 V pulse out for each pulse in Connect the Positive signal wire 5 V pulse to terminal marked P and the Return to the terminal marked COM in the rear panel section labeled OUT
9. rdware product covered by this limited warranty shall be limited to and fully discharged by the SELLER s option of replacement or repair of such item without charge The limited warranty provided in this clause is in lieu of all other warranties expressed or implied arising by law or otherwise ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FORA PARTICULAR PURPOSE ARE EXCLUDED This limited warranty shall not be modified except by an arrangement signed by both parties specifically referencing this clause SELLER warrants that any software supplied will operate in accordance with the documentation or manual supplied therewith in all material respects when used in strict compliance with such documentation or manual Notwithstanding the foregoing BUYER acknowledges that since software is complex and therefore may have defects BUYER s sole and exclusive remedy for any such defects or breach of this warranty shall be to require SELLER within a reasonable period of time to provide all reasonable programming services to correct programming errors in the software Except as provided above SELLER MAKES AND BUYER RECEIVES FROM SELLER NO EXPRESS OR IMPLIED WARRANTIES OF ANY KIND WITH RESPECT TO ALL OR ANY PORTION OF SOFTWARE AND BUYER HEREBY AGREES AND ACKNOWLEDGES THAT IT ACCEPTS THE SOFTWARE IN AS IS CONDITION SELLER HEREBY EXPRESSLY EXCLUDES ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE WITH RESPECT TO THE
10. volution Model ACT 1B 60 Power may be either 115 Vac or 230 Vac 50 60 Hz or optionally 12 Vdc to 15 Vdc The ACT 1B Series accepts input signals from optical proximity magnetic infrared or laser sensors or direct TTL or external ac inputs All models are suitable for panel mounting or bench top with convenient screw terminal connections on the rear panel of the instrument If specified at time of order placement the ACT 1B may be equipped with either an optional 4 to 20 mA current output IO or 0 to 5 Vdc analog output AO proportional to speed and or a TTL pulse repeater output PO INSTALLATION and POWER The ACT 1B enclosure is a standard 1 8 DIN size requiring a 3 58 wide by 1 74 high 91x44 mm mounting hole 3 58 91 Panel Cutout 1 74 44 ACT Front View ACT Side View 0 28 7 0 31 8 3 94 100 3 79 96 1 90 48 Figure 1 Dimensions in Inches mm _ we Installation Remove the mounting clips if fitted and install the unit into the panel from the front From the rear of the unit install the mounting clips on each side and tighten the mounting screws against the rear of the panel WARNING Do not over tighten the mounting screws Power Power to the unit is connected to the terminals under the section labeled POWER on the rear panel Be sure the power supplied matches the specification indicated on the rear pane
Download Pdf Manuals
Related Search