Home

Minolta CF2001P Printer User Manual

1. 7664 7714 01 nce CF2001P User Manual If used as a MicroPress printer refer to the manual in the Minolta MicroPress Cluster Printing System server DiALTA Color Energy Star Lot fet As an ENERGY STAR Partner we have determined that this machine meets the ENERGY STAR Guidelines for energy efficiency What is an ENERGY STAR Product An ENERGY STAR product has a special feature that allows it to auto matically switch to a low power mode after a period of inactivity An EN ERGY STAR product uses energy more efficiently saves you money on utility bills and helps protect the environment Trademarks and Registered Trademarks Fiery and the Fiery logo are registered trademarks of Electronics for Im aging Inc Fiery X3e is a trademark of Electronics for Imaging Inc T R Systems MicroPress and other T R Systems product names are either trademarks or registered trademarks of T R Systems Inc in the United States and other countries DiALTA and NMT are registered trademarks of Minolta Co Ltd All other product names mentioned are trademarks or registered trade marks of their respective companies Te Contents 1 Introduction 1 1 1 2 1 3 1 4 1 5 We Want You to Be a Satisfied Customer 1 1 SAFETY INFORMATION cene enne en nnnnn nnn nn
2. CF2001P 5 Control Panel Messages 6 Remove any paper f Close the upper door and the lower door 8 Slide the 10 mailbin sorter back against the printer S Note Be careful about a protrusion on the backside of the horizontal transport unit cover It can hurt you Part indicated in Step 4 932 CF2001P Control Panel Messages 5 To clear jammed staples 1 Slide the finisher away from the printer 2 If finisher FN 107 is installed open right side door FN7 3 Turn the dial to the left in order to position the stapler at the center CF2001P 5 33 Control Panel Messages 4 O Finisher FN 107 O Finisher FN 108 Since finisher FN 107 is equipped with two staple hold ers which staple holder should be pulled out The message on the control panel indicates which staple holder should be pulled out r 59 Push the staple holder guide up and then pull out one sheet of sta ples 6 Move the guide back to its original position Pull the staple holder out toward you Back Staple 5 34 CF2001P Control Panel Messages 5 f Insert the staple holder until it locks into place O Finisher FN 107 O Finisher FN 108 8 If finisher FN 107 is installed close right si
3. No Part Name Description 1 Print output tray Holds printouts fed from the printer 2 Toner supply door Opened when adding toner 3 Front door Opened when servicing the printer 4 Tray 1 Holds 250 sheets of paper The paper size can be adjusted freely Special paper can be used See p 4 7 5 Tray 2 Holds 500 sheets of paper The paper size can be adjusted freely See p 4 12 6 Power switch Used to turn the printer on and off See p 3 14 7 Right side door Opened when servicing the printer and clearing misfeeds 8 Right side door release Used to open and close the right side door lever 9 Manual bypass tray Used for manual feeding of paper The paper is fed one sheet at a time 10 Lower right side door Opened when clearing misfeeds 11 Left side door Opened when servicing the printer 12 Control panel Displays the current status of the printer 13 Printer power cord Used for connecting the printer s power cord socket 14 Sorter finisher connec Used for connecting the sorter or finisher hookup cord tor When Fiery X3e is installed printing from the manual bypass tray is not supported CF2001P 3 5 Before Making Prints Inside of Printer No Part Name Description 1 Toner hopper lid Opened when adding toner 2 Imaging unit release le Used to install and replace the imaging unit ver 3 Imaging unit removing Used to remove the imaging unit bracket 4 Upper rig
4. 5 1 Rightleft buttons Rc 3 13 SIUE M 3 13 Up down bUTIONS ET 3 13 Copy rrqm 3 3 Copy table 25 neat eiie dehet perrita 3 3 DUPIOX UNE Pee OR 3 2 3 8 7 3 EEVT E c 1 13 FMS rige 3 2 3 10 7 5 7 6 ab 3 5 Fusing WIE M RESET 3 7 FUSING WED UN It ena tetpce utin E nb tere cede reti tiros hiia 3 7 Image transfer belt unit sesssssssssseeeeeenen 3 7 Image transfer roller unit sess 3 7 Imaging Umit c m 3 7 lnst llation Site NRERTCNTET 2 1 CF2001P 8 1 Index Large capacity cabinet eee 3 2 3 12 7 3 LED cleaning tool Rege i ee as 3 7 left side dOr ctr iE REN fut tees Meh ceases reete 3 5 Lower right side dOOr acier tecti ener i EN 3 5 Manual bypass tray sss emen nene 3 5 Message Near troble XX XX Appears eee 5 38 No xxxx Staples Appears sesem ee 5 12 Service Code Cxxxx Appears s 5 36 Xxxx toner nearly empty 5 8 xxxx unit near life limit Appears A 5 37 Message list iot oerte tegere gie i PH EET 5 1 OPP TIM See tentes re thas Stehen ee Ert a IS recu 4 4 lereer ieBv a 3 7 Operation precautions eesseeeee mme 2 3 Options 10 Mailbin Sorter 4 inicr toe ttes tere d Pei 3 1 3 9 Copy desk beet DH
5. A location away from curtains etc that may catch fire and burn easily A location that is not exposed to water or other liquids A location free from direct sunlight A location out of the direct airflow of an air conditioner or heater and not exposed to extremely high or low temperatures A well ventilated location A location that is not exposed to high humidity A location that is not extremely dusty A location not subjected to undue vibrations A stable and level location A location where ammonia or other organic gases are not generated A location that does not place the operator in the direct airflow of ex haust from the printer A location that is not near any kind of heating devices Power source The power source requirements are as follows e O Voltage fluctuation Maximum 10 AC 127 V areas only between 10 and 6 Frequency fluctuation Maximum 0 3 Use a power source with as little voltage or frequency fluctuations as possible CF2001P 2 1 Precautions Space requirements To ensure easy printer operation supply replacement and maintenance adhere to the recommended space requirements detailed below 63 98 1 625 10 43 8 27 265 45 28 1 150 210 ah 55 1 397 20 510 31 787
6. 6 Set button Activates the currently selected option and if applicable proceeds to the next menu 7 Cancel button Exits the setup and returns to Info stops printing or processing the current job if pressed when printing 8 Message light Lights up in red for more than 30 seconds to indicate a communication error between the Fiery X3e and the printer Flashes red if there is an error that prevents printing CF2001P 3 13 Before Making Prints To turn the printer on Set the power switch to To turn the printer off Set the power switch to O Power Switch Turning the printer on and off 3 Note Do not turn off the printer while it is printing otherwise a paper misfeed may occur Make sure that all print operations are finished before turning off the printer S Note With Fiery X3e installed if the printer is turned off directly instead of turning off the system using the control panel the controller may be damaged S Note If the printer is not used for 15 minutes it automatically enters Energy Saver mode The printer will automatically start warming up as soon as it receives a print job or when any cover is opened then closed CF2001P Before Making Prints Turning On the Printer After the printer is turned on the controller is initialized After the controller has finished warming up the Ready light lights up in gr
7. CF2001P 5 Control Panel Messages 5 3 When the Message No xxxx staples Appears S Note Be sure to replace the staple cartridge only after the message No xxxx staples appears Injuries may occur if the staple cartridge is re moved before the message appears To replace the staple cartridge 1 Slide the finisher away from the printer 2 If finisher FN 107 is installed open right side door FN7 3 Turn the dial to the left in order to position the stapler at the center 5 12 CF2001P Control Panel Messages 5 4 Pull the staple holder out toward you O Finisher FN 107 Back Staple O Finisher FN 108 Back Staple 9 Since finisher FN 107 is equipped with two staple holders which staple holder should be pulled out The message on the control panel indicates which staple holder should be pulled out 5 Finisher FN 107 Remove the empty staple cartridge from the staple holder CF2001P 5 13 Control Panel Messages 6 7 Finisher FN 107 Insert the new staple cartridge into the staple holder and then carefully remove the stopper Finisher FN 108 Remove the empty staple cartridge from the staple holder Finisher FN 108 Insert the new staple cartridge into the staple holder and then carefully remove the stopper
8. The image transfer belt unit requires replacement Contact your technical representative The printer s internal paper path is dirty Run several prints to flush out the debris The imaging unit requires re placement The image transfer roller unit requires replacement The oiling roller requires re placement Contact your technical representative The printer s internal paper path is dirty Run several prints to flush out the debris The oiling roller requires re placement Contact your technical representative The imaging unit requires re placement Contact your technical representative Black pages The imaging unit requires re placement Contact your technical representative 6 2 CF2001P Troubleshooting Symptom Cause Action Blank pages The imaging unit requires re placement Contact your technical representative Paper wrinkles during printing The paper being used is not compatible with the printer See 4 1 Paper Specifications for compatible types of paper p 4 1 Paper is not loaded properly in the tray See 4 4 Loading Paper p 4 7 The fusing unit requires re placement Contact your technical representative The print image is not fixed and easily smears The paper loaded in the tray is damp Replace the old paper with fresh dry paper
9. seeseeesseeeeseeeeeennnee entem 2 2 iere e 7 1 Staple jam clearing sse 5 16 5 33 T To load paper into the large capacity cabinet ssuuuss 4 14 To load paper into the manual bypass tray esseeee 4 16 To load paper into Tray 1 250 sheet multipurpose tray 4 7 To load paper into Tray 2 or the 500 sheet paper feed unit 4 12 To print the total counter sseee eme 3 18 Toner hoppet lig 5 5 ree eee EeRES 3 6 Toner supply door IL RI Et Leder 3 5 Tray T usce ter RETRO ee ADEEEHOTRR 3 5 Mc channeled 3 5 Troubleshooting iot e reir eere aede e tecto 6 1 Turning the printer on and Off esse 3 14 U Upper right side door iiin aaa ea aana aar aa aara a terne 3 6 CF2001P 8 3 8 Index Waste toner bottle net t at rte tha ice 3 7 8 4 CF2001P 0 MINOLTA Copyright 2001 MINOLTA CO LTD The information contained in this manual is subject to change without notice to incorporate improvements made on the product or products the manual covers MINOLTA CO LTD 3 13 2 Chome Azuchi Machi Chuo ku Osaka 541 8556 Japan 2001 8
10. Safe to power off the system appears 5 Set the power switch to O a Ready a Message Safe to power off the system Menu Set Cancel CF2001P 3 17 3 Before Making Prints 3 5 Total Counter The total counter can be printed out by following the procedure below To print the total counter 1 Check that Info XXXX appears in the display and then press the m E Menu button in the control panel Ready Message Info XXXx CJI D9 2 Press A or V until Function Print Pages appears and then press the z z Set button Ready Message Functions Print Pages Menu X Set Cancel 3 Press A or W until Functions Total Counter appears and then press z the Set button Ready Message Functions Total Counter A EJ Ly Cancel 3 18 CF2001P Before Making Prints 4 The total counter is printed out Refer to page 4 7 for Loading 200 6 26 16 29 Paper Serial Total Check Full Color Black Dup Copy Copy 0 0 0 Dup Print G Total 81 CF2001P 3 19 3 Before Making Prints 3 20 CF2001P Print Paper 4 E 4 Print Paper 4 1 Paper Specifications Use paper that meets the following specifications Paper Types Tray 1 Tray 2 Manual bypass tray Paper Feed Unit Of O OOJO O O O O Large Cap
11. Cabinet See p 4 14 Printer Controller Fiery X3e For more details refer to the manual of the printer controller Printer Controller MicroPress PrintLink 2020m For more details refer to the manual of the printer controller 3 12 CF2001P Before Making Prints 3 3 3 Names of Control Panel Parts and Their Functions Names of Control Panel Parts and Their Functions 1 8 2 3 4 Set Cancel 5 6 7 No Part Name Description 1 Ready light Off when the Fiery X3e is off or starting up Lights up in green to indicate the normal operating condition Flashes green when the Fiery X3e is proceeding to RIP or printing a job or communicating with a remote computer for example through the Fiery Spooler 2 Display window Displays information about the current status 3 Up down buttons Up button Returns to the previous option or setting if pressed when a menu is displayed displays the previous character if pressed when entering text Down button Advances to the next option or setting if pressed when a menu is displayed displays the next character if pressed when entering text 4 Right left buttons Right arrow Advances the cursor to the next entry position on the right Left arrow Deletes the character to the left if pressed when entering text 5 Menu button Displays the Functions menu returns to the menu if pressed after an option has been selected
12. The setting in the printer driv er is not set properly Adjust the setting in the print er driver to the desired level The paper loaded in the tray is damp Replace the old paper with fresh dry paper p 4 7 The toner hopper is running out of toner Refill the toner p 5 8 The imaging unit may be defective Contact your tecnical representative The image transfer belt unit may be defective Contact your tecnical representative The image is too dark The setting in the printer driv er is not set properly Adjust the setting in the print er driver to the desired level The imaging unit requires replacement The image transfer belt unit requires replacement Contact your tecnical representative The image transfer roller unit requires replacement The oiling roller requires re placement Contact your technical representative The paper loaded in the tray is damp Replace the old paper with fresh dry paper The imaging unit requires re placement The image transfer belt unit requires replacement Contact your technical representative CF2001P 6 1 Troubleshooting Symptom Cause Action Inconsistent image density The imaging unit requires re placement The image transfer belt unit requires replacement Contact your technical representative The imaging unit requires re placement
13. basna EE E zu ens eme ene Illum SS e ehem 4 SS RI vod o r T mo Mente 9 Unit inch mm 62 17 1 579 9 25 8 27 235 44 65 1 134 210 t 55 1 397 20 510 31 787 zo Om uA Ww CS M i oS 3 l 2 Wiser SS i eo l E uo LAS e 4 ry I9 LJ I I mem 9 mo Unit inch mm S Note Be sure to allow a clearance of 4 in 100 mm or more at the back of the printer for the ventilation duct CF2001P Precautions 2 2 2 Operation Precautions Operating environment The environmental requirements for correct operation of the printer are as follows e Temperature 50 F 10 C to 86 F 30 C with fluctuations of no more than 18 F 10 C within an hour e Humidity 25 to 85 with fluctuations of no more than 20 within an hour Proper use To ensure the optimum performance of the printer follow the precautions listed below Never open any printer doors or turn off the printer while it is printing otherwise a paper jam will occur Never bring any magnetized object or use flammable sprays or liquids near the printer Always make sure that the power plug is completely plugged into the electrical outlet Always make sure that the printer s power plug is visible and not hid den by the printer Always unplug the printer from the electrical outlet if the unit is not to be used for a
14. bend pull on or damage the power cord Use of a damaged power cord exposed core wire broken wire etc could result in a fire or breakdown Should any of these conditions be found immediately turn OFF the power Switch unplug the power cord from the power outlet and then call your au thorized service representative In principle do not use an extension cord Use of an extension cord could cause a fire or electrical shock Contact your authorized service represen tative if an extension cord is required Do not place a flower vase or other container that contains water or metal clips or other small metallic objects on this product Spilled water or metallic objects dropped inside the product could result in a fire electrical shock or break down Should a piece of metal water or any other similar foreign matter get inside the product immediately turn OFF the power switch unplug the power cord from the power outlet and then call your authorized service representative fthis product becomes inordinately hot or emits smoke or unusual odor or noise immediately turn OFF the power switch unplug the power cord from the power outlet and then call your authorized service representative If you keep on using it as is a fire or electrical shock could result If this product has been dropped or its cover damaged immediately turn OFF the power switch unplug the power cord from the power outlet and then call your authorize
15. right side door FN7 5 While holding open misfeed clear ing guide FN8 for finisher FN 107 or FN7 for finisher FN 108 re move any paper CF2001P 5 27 5 Control Panel Messages 6 If finisher FN 107 is installed close right side door FN7 7 Open front door FN4 8 Turn knobs FN5 at the same time to feed out any paper 9 Close front door FN4 10 Open upper cover FN1 11 While holding misfeed clearing guide FN2 open remove any paper 5 28 CF2001P Control Panel Messages 5 12 While holding misfeed clearing guide FN3 open remove any paper 13 Close upper cover FN1 14 While holding misfeed clearing guide FN6 open remove any paper 15 Slide the finisher back against the printer S Note Be careful about a protrusion on the backside of the horizontal transport unit cover It can hurt you Part indicated in Step3 CF2001P 5 29 5 Control Panel Messages To clear a paper misfeed in the 10 mailbin sorter 1 Slide the 10 mailbin sorter away from the printer 2 Remove any paper from the mail bins 3 Open the cover of the horizontal transport unit 5 30 CF2001P Control Panel Messages 4 Remove any paper and then close the cover of the horizontal transport unit 5 Open the upper door and the lower door
16. Advance warning message When it is almost time to replace a unit the message xxxx unit near life limit appears in the control panel Prepare the new unit and replace it as soon as possible e Replacement warning message After the advance warning message has appeared about 1 000 print outs can be made before the printer stops operating The number of printouts depends on the selected print settings and the unit In addi tion the message xxxx unit over life limit xxxx appears in the control panel followed by instructions for replacing the unit Replace the unit according to the instructions that appear S Disposing of Used Parts Dispose of used units according to your local regulations or contact your technical representative CF2001P 5 37 Control Panel Messages 5 7 When the Message Near troble XX XX Appears When the message shown below appears in the control panel display image stabilization and printing functions for the printer have become unstable Ready Mossad Alert Near trouble Ca Cx gt mn mn Menu Set Cancel Press W once and click which error code is displayed Ready Messan Cw Menu Set _ Cancel If this message appears contact your technical representative and inform them of the error coad that is indicated 5 38 CF2001P Troubleshooting 6 Troubleshooting 6 1 Improving Print Quality Symptom Cause Action
17. H 20 59 in 523 mm Space requirements W 25 28 in 642 mm D 28 74 in 730 mm Weight 187 39 Ibs 85 kg with one 500 sheet paper feed unit and all four imaging units installed 500 sheet Paper Feed Unit PF 118 Specification Paper types Standard paper 17 02 to 23 94 Ibs 64 to 90 g m Paper sizes 11 x 17L 11 x 14L LegalL LetterL LetterC A3L A4L A4C Capacity 500 sheets 21 28 Ibs 80 g m Power source Supplied from printer Power consumption Less than 9 W Dimensions W 21 06 in 535 mm D 22 36 in 568 mm H 5 39 in 137 mm Weight About 18 75 Ibs 8 5 kg CF2001P Appendix Large capacity Cabinet PF 117 Specification Paper types Standard paper 17 02 to 23 94 Ibs 64 to 90 g m Paper sizes US LetterC Europe A4C Capacity 2500 sheets 21 28 Ibs 80 g m Power source Supplied from printer Power consumption Less than 45 W Dimensions W 21 06 in 535 mm D 22 36 in 568 mm H 11 18 in 284 mm Weight About 36 82 Ibs 16 7 kg Duplex Unit AD 14 Specification Paper types Standard paper 17 02 to 23 94 Ibs 64 to 90 g m Paper sizes 12 25 x 18L 5 11 x 17L 11 x 14L LegalL LetterL LetterC Ex ecutiveL ExecutiveC 5 5 x 8 5L A3WideL A3L A4L A4C A5L 1 For US only 2 For Europe only Power source Supplied from printer Power c
18. as possible Waste toner bottle not set The waste toner bottle is not installed Install the waste toner bottle Xxxx toner nearly empty The toner for the indicated color will soon be empty Refill the toner for the indicated color Xxxx unit The indicated unit will soon Replace the indicated unit near life limit reach the end of its service life Xxxx unit The indicated unit is not Install the indicated unit not set installed Xxxx unit The indicated unit is not Install the indicated unit not set right installed correctly correctly or contact your technical representative Xxxx unit The service life for the Ask your technical over life limit indicated unit has expired representative to replace the Call service indicated unit Xxxx unit The service life for the Replace the indicated unit over life limit indicated unit has expired Please change 5 3 5 Control Panel Messages To load paper into Tray 1 250 sheet multipurpose paper drawer 1 Pull out the paper drawer oe up roller 9 Has the paper take up roller been touched Be careful not to touch the sur face of the paper take up roller with your hands If the roller has been touched wipe it with a dry cloth 2 Press down on the paper lifting plate until it locks into place 3 Load the paper into the drawer so that the front side of the paper the side facing up when t
19. correctly gt When hitting the toner bottle against a surface be sure to hold the bottle so that the open ing of the bottle is pointing up 3 While firmly grasping the new toner bottle shake it well 9 3 Is the toner within the bottle v hard d The toner within the bottle may V A become compacted If it does Ws be sure to shake the bottle until the toner is mostly broken up be fore adding it to the hopper CF2001P 5 9 Control Panel Messages 4 With the rounded side marked with w of the bottle mouth facing to wards you place the toner bottle on top of the hopper and then press down on the bottle until it snaps into place 5 Fully pull the toner hopper shutter out toward you Pulling out the toner hopper shutter allows the toner to fill the toner hop per Check that all of the toner has emp tied out of the toner bottle and into the hopper which may take a while Do you know what precautions should be taken when refilling the toner 2 Do nottap on the toner bottle while refilling the hopper otherwise the toner may spurt out 6 Push the toner hopper shutter closed CF2001P Control Panel Messages 7 Tilt the toner bottle backward and then pull the opening of the bottle up and toward you to remove it 8 Close the toner hopper lid and then close the toner supply door
20. interface Parallel cable and shielded network 10 100Base T cable The use of non shield cables is likely to result in interference with radio communications and is prohibited under CISPR 22 and local rules Ozone Release Locate the machine in a Well Ventilated Room A negligible amount of ozone is generated during normal operation of this machine An unpleasant odor may however be created in poorly ventilat ed rooms during extensive machine operations For a comfortable healthy and safe operating environment it is recommended that the room be well ventilated Placer l appareil dans une pi ce largement ventil e Une quantit d ozone n gligeable est d gag e pendant le fonctionnement de l appareil quand celui ci est utilis normalement Cependant une odeur d sagr able peut tre ressentie dans les pi ces dont l a ration est insuffisante et lorsque une utilisation prolong e de l appareil est effec tu e Pour avoir la certitude de travailler dans un environnement r unis sant des conditions de confort sant et de s curit il est pr f rable de bien a rer la pi ce ou se trouve l appareil CF2001P 1 7 Introduction WARNING LABEL Model CF2001 Input Total eric Tool OOO OA at 199C m mo Qs TES loss A digital apporatus complies wi This Canadian 1CES 003 Cet appareil nunerique de le classe A est conforme a lo Serial No norne NIB 003 du Canada Europe Model CF20
21. lock release levers for the oil coating unit in the direction of the arrows 5 24 CF2001P Control Panel Messages 5 6 Move the levers one on each end of the oil coating unit in the direc tion of the arrows and carefully pull out the paper f While holding the levers on the ends of the oil coating unit move the unit back to its original position 8 Fully move the two lock release le vers for the oil coating unit in the di rection of the arrows 9 Close the upper right side door 10 Close the right side door AN CAUTION The area around the fusing unit is extremely hot Touching anything other than the indicated levers around the fusing unit may result in burns f you get burnt immediately cool the skin under cold water and then seek professional medical advice CF2001P 5 25 5 Control Panel Messages To clear a paper misfeed in finisher FN 107 FN 108 AN CAUTION Metallic parts inside Misfeed Clearing Guide FN1 are very hot Part indicated in Step 10 Do not touch anything but the paper to prevent you from getting burned 1 Slide the finisher away from the printer 2 Open the cover of the horizontal transport unit 5 26 CF2001P Control Panel Messages 5 3 Remove any paper and then close the cover of the horizontal transport unit 4 If finisher FN 107 is installed open
22. long period of time F Always provide good ventilation when making a large number of con tinuous prints AN CAUTION A negligible amount of ozone is generated during normal operation of this printer An unpleasant odor may however be detected in poorly ventilated rooms during extensive printer operations 4 Foracomfortable operating environment it is recommended that the room be well ventilated CF2001P 2 3 Precautions AN CAUTION If the ventilation duct at the top of the printer becomes blocked the inside of the printer will accumulate heat resulting in a malfunction or fire Do not place any objects over the ventilation duct A CAUTION The area around the fusing unit is extremely hot Be careful not to touch any parts around the fusing unit other than those indicated in this manual in order to reduce the risk of burns Be especially careful not to touch parts marked with warning labels and their surrounding areas Ifyou get burnt immediately cool the skin under cold water and then seek professional medical advice Transporting the printer If you need to transport the printer over a long distance consult your ser vice representative Care of printer supplies Use the following precautions when handling the printer supplies toner paper etc tt Store the supplies in a location that meets the following requirements free from direct sunlight away from any heat
23. puter then feeds out the pages Note If MicroPress PrintLink 2020m is in stalled only FN107 is supported Duplex unit AD 14 optional Automatically turns over prints al lowing double sided prints to be made Paper feed unit PF 118 optional Can supply 500 sheets of paper up to two paper feed units can be in stalled Large capacity cabinet PF 117 op tional Can supply 2 500 sheets of paper CF2001P Before Making Prints e Copy desk optional Used when the optional 10 mailbin sorter JS 1002 or an optional fin isher FN 107 FN 108 is installed without an optional paper feed unit Copy table optional Used when the optional 10 mailbin sorter JS 1002 or an optional fin isher FN 107 FN 108 is installed with two optional paper feed units installed Printer controller Fiery X3e SEES Internal printer controller that allows the printer to be used as a color printer on a network Printer controller MicroPress PrintLink 2020m Internal printer controller that allows the printer to be used as a color printer on a network CF2001P Before Making Prints Parts Names and Their Functions 3 2 Outside of Printer are a7 lI 7 The copy desk shown installed in the illustration is optional CF2001P 8 4 Before Making Prints
24. shown as B Paper Orientation Lengthwise L If the width A of the paper is shorter than the length B the paper has a ver tical or portrait orientation indicated by either L or Ly Crosswise JJ If the width A of the paper is longer than the length B the paper has a hor izontal or landscape orientation indi cated by either C or J CF2001P Introduction 1 1 5 Features The Minolta CF2001P is a high speed high quality full color printer com bining the functionality and compactness best suited for any office e Delivers high speed high quality full color printouts High quality business standard images with a resolution of 600 dpi x 600 dpi simulated 256 variations High speed full color printing Letter A4 landscape continuous print ing at 20 sheets per minute Combines handling of a large paper capacity in a compact design Lightweight space saving full color printer Maximum paper capacity of 3 250 sheets including optional paper cassettes Can be combined with a wide variety of options 10 mailbin sorter paper feed unit and duplex unit etc providing even more features CF2001P 1 13 Introduction CF2001P Precautions 2 Precautions 2 1 Installation Precautions Installation site To ensure utmost safety and prevent possible malfunctions install the printer in a location that meets the following requirements
25. 01 Input Total Serial No CAUTION Install this machine so that it can quickly be unplugged from the electrical outlet in case of an emergency The socket outlet shall be installed near the machine and shall be easily accessible LED Radiation Safety This product is a printer which operates by means of a LED light emitting diodes exposure system There is no possibility of danger from the LED optical radiation because the LED optical radiation level does not exceed the accessible radiation limit of class 1 under all conditions of operation maintenance service and failure 1 8 CF2001P Introduction 1 1 3 Guide to Manuals Enclosed Manuals In order to refer to the User Manual quickly when necessary store it near the printer e User Manual The User Manual describes the functions operating procedures pre cautions and basic troubleshooting for this printer Before using this printer be sure to read the User Manual thoroughly in order to ensure that the printer operates properly and is used efficiently Explanation of Manual Conventions The marks and text formats used in this manual are described below A WARNING Failure to observe instructions highlighted in this manner may result in fatal or critical injuries Observe all warnings in order to ensure safe use of the printer AN CAUTION Failure to observe instructions highlighted in this manner may result in s
26. 105 Power is not being supplied to the DT105 Check that power is supplied to the DT105 Cover open at XX The indicated cover is open Press w once check which cover is open and then close it Front p 3 5 3 Right Side p 3 5 7 Left Side p 3 5 11 Fusing Unit p 3 6 4 2nd Feed p 3 5 10 3nd Feed p 3 11 1 4th Feed p 3 11 1 LCC Feed p 3 12 1 Duplex p 3 8 1 Horizontal Transport p 3 9 4 Finisher Front p 3 10 4 Finisher Upper p 3 10 1 Sorter Correctly attach the sorter to the printer Finisher Correctly attach the finisher to the printer Image Stabilizing The printer is now image sta bilizing No action required Load xx Paper of size xx and type xx Load paper of size xx and xx in xx is not loaded in the specified type xx into the specified tray tray Load xx Xx size paper is not loaded Load xx size paper into the in xx into the specified tray specified tray CF2001P 5 1 Control Panel Messages Message Cause Action Load xx Xx size overhead projector Load xx size overhead pro OHP in tray1 transparencies is not loaded jector transparencies into into tray 1 tray 1 Load xx Xx size paper has not been Load xx size paper into any in any tray loaded into any tray tray Load xx Xx size thick 1 is not loaded Load xx size thick 1 into Thick 1 in tray1 into tray 1 tray 1 Near trouble Some
27. 2 1 lude Tacoim HL ria 2 1 Space requirements eesseeeeeseeeeeeenreeenn nennen 2 2 2 2 Operation Precautions eeeeeeeeeeeeeeeeee eene nnn 2 3 Operating environment essent 2 3 diea ES 2 3 CF2001P i Transporting the printer see 2 4 Care of printer supplies ese 2 4 3 1 Components and Their Functions eene 3 1 3 2 Parts Names and Their Functions eene 3 4 Outside of Printer cecidere ni 3 4 Inside of Priliter esci itcm eie ri eee trito deti d 3 6 Supplies and Parts Naik ate e tbt Dres 3 7 D plex Unit Optional 1 t rtt e tere t i 3 8 10 Mailbin Sorter Optional eee 3 9 Finisher Optional etit tree enr ttti nx 3 10 Paper Feed Unit Optional en 3 11 Large Capacity Cabinet Optional eene 3 12 Printer Controller Fiery X3e sse 3 12 Printer Controller MicroPress PrintLink 2020m 3 12 3 3 Names of Control Panel Parts and Their Functions 3 13 Names of Control Panel Parts and Their Functions 3 13 3 4 Power Switch eese eene eene nennen nnne nenne nennt 3 14 Turning the printer on and off sss 3 14 To turn the printer on ssseenmem e 3 14 To turn the
28. 2 500 sheet paper feed unit 11 x 17L 11 x 14L LegalL LetterL LetterC A3L A4L A4C Manual bypass tray 12 25 x 18L 11 x 17L 11 x 14L LegalL LetterL LetterC ExcecutiveL ExcecutiveC 5 5 x 8 5L 5 5 x 8 5C 4 x 6L 1 A3WideL A3L A4L A4C ABL A5C AGL Large capacity cabinet LetterC AAC 1 For US only For Europe only MicroPress PrintLink 2020m only 3 Input capacity Tray 1 250 sheets when using 21 28 Ibs 80 g m standard paper Tray 2 500 sheet paper feed unit 500 sheets when using 21 28 Ibs 80 g m standard paper Manual bypass tray 1 sheet standard paper thick paper 1 thick paper 2 overhead projector transparencies or postcard Large capacity cabinet 2500 sheets when using 21 28 Ibs 80 g m standard pa per MicroPress PrintLink 2020m only Output capacity 250 sheets standard paper Warm up time Less than 5 minutes at room temperature 68 F 20 C CF2001P 7 1 Appendix Specification First print Full color Less than 15 seconds Black Less than 12 seconds Print speed Full color Black LetterC A4C 20 sheets min LetterL A4L 14 sheets min A3L 11 x 17L 10 sheets min Memory 304 MB Power Requirements US 110 120 127 V 15 A 60 Hz Europe 220 240 V 10 A 50 60 Hz Power consumption US Less than 1 3 kW Europe Less than 1 5 kW Dimensions W 23 46 in 596 mm D 28 74 in 730 mm
29. A4C ABC Short edge 2 3 1 4 holes 12 25 x 18L 11 x 17L 11 x 14L LegalL LetterL Executiv eL 5 5 x 8 5L A3WideL 2 ASL A4L ABL 1 For US only 2 For Europe only Power source Supplied from printer Power consumption Less than 63 W Dimensions W 21 18 in 538 mm D 24 76 in 629 mm H 38 50 in 978 mm Weight About 86 42 Ibs 39 2 kg Accessories 2 staple cartridges 5 000 staples CF2001P 7 5 Appendix Finisher FN 108 Specification No of bins 2 Upper paper output tray Lower paper output tray Paper types Upper paper output tray Standard paper 17 02 to 23 94 Ibs 64 to 90 g m thick paper 24 21 to 55 59 Ibs 91 to 209 g m overhead projec tor transparencies postcards Lower paper output tray Standard paper 17 02 to 23 94 Ibs 64 to 90 g m Paper sizes Upper paper output tray 12 25 x 18L 11 x 17L 11 x 14L LegalL LetterL LetterC ExecutiveL ExecutiveC 5 5 x 8 5L 5 5 x 8 5C 4 x 6L 1 A3WideL A3L A4L A4C ABL A5C AGL Lower paper output tray 12 25 x 18L 11 x 17L 11 x 14L LegalL LetterL LetterC ExecutiveL ExecutiveC A3WideL A3L A4L A4C For US only For Europe only Capacity of bins Upper paper output tray Standard paper 21 28 Ibs 80 g m Maximum 250 sheets Thick paper Maximum 20 sheets Overhead projector transparencies Maximum 1 sheet Postcards Maximum 20 sheets Lower pape
30. CF2001P Control Panel Messages 5 9 Insert the refilled staple holder until it locks into place O Finisher FN 107 IN O Finisher FN 108 10 If finisher FN 107 is installed close right side door FN7 11 Slide the finisher back against the printer CF2001P 5 15 5 Control Panel Messages 5 4 Clearing a Paper Misfeed and Staple Jam If a paper misfeed or a staple jam occurs during printing the message shown below appears oO Oo Ready Message Alert Paper jam at Cw Set_ Cancel Press W once and check where the paper misfeed occurred Menu Set_ Cancel Follow the procedure below to clear the misfed paper or the jammed staples 5 16 CF2001P Control Panel Messages Message Description Message Description JA Paper drawers p 5 21 JB Paper drawers p 5 21 JC Paper drawers p 5 21 JD Paper drawers p 5 21 JE Manual bypass tray p 5 18 JF Duplex unit p 5 20 JG Printer p 5 23 JH Printer p 5 23 Jl Printer p 5 23 JJ Finisher FN 107 FN108 p 5 26 10 mailbin sorter p 5 30 JK Finisher FN 107 FN108 p 5 26 JL Finisher FN 107 FN108 p 5 26 10 mailbin sorter p 5 30 10 mailbin sorter p 5 30 CF2001P 5 Control Panel Messages To clear a paper misfeed in the manual bypass tray AN CAUTION Decreased print quality may resul
31. E aSa 7 7 CF2001P CF2001P Introduction i EE 1 Introduction 1 1 We Want You to Be a Satisfied Customer Thank you for choosing a Minolta CF2001P To ensure the best performance and effective use of your printer this manual will provide information on the following topics e Getting to Know Your printer e Initial Steps e Troubleshooting Please read this manual carefully before using your printer and keep it handy at all times Store the manual in the holder on the rear side of the printer 1 2 SAFETY INFORMATION This section contains detailed instructions on the operation and mainte nance of this machine To achieve optimum utility of this device all oper ators should carefully read and follow the instructions in this manual Please keep this manual in a handy place near the machine Please read the next section before using this device It contains important information relat ed to user safety and preventing equipment problems Make sure you observe all of the precautions listed in this manual Please note that some parts of the contents of this section may not correspond with the pur chased product CF2001P 1 1 1 Introduction Warning and Precaution Symbols Ignoring this warning could cause serious injury or even death Ignoring this caution could cause injury or damage to property Meaning of Symbols A triangle indicates a danger against which you s
32. Heat eee e d eee tend arta 3 3 Copy table r 2 eere p E ee ee eee d etes 3 3 D pl x nit sc 21 2 2 EIER prier pri deren tior iud 3 2 3 8 MEI ERRERIIERUOTUDE IAE 3 2 3 10 Large capacity cabinet sssssssssseeeeee 3 2 3 12 Paper feed unit eese 3 2 3 11 Overhead projector transparencies eeseenn 4 4 Ozone filter nace rn tti EE o ec ales 3 7 Paper feed unit ote ee ele 3 2 3 11 Paper feeding path esee nennen 1 11 Paper misfeed clearing esses 5 16 T0 mailbin Sorter 2 ot Ree Re re et RE ere p uita eed 5 30 D plex UM its 4 2 i da e nei zem esl oro D dee eee 5 20 Einlshet e tp ERE niu ean 5 26 Manual bypass tray meme 5 18 CF2001P Index Paper feed Units ii ia rne ep desea ee iets 5 21 Printer sue et ec cake Seeds caves itr e PR 5 23 Paper OrientatiOn ecicee ceci t eo tete eer ide eter ie se cua edes 1 12 Paper SIZ6S a aure RR e cas ERE Ra 4 2 Paper types 2 5 ree epi teo e 4 1 neum 2 1 Power SWItCh E 3 5 Printo tput Iray esee o tetuer EPREERIREERESE ERE 3 5 PING ere IET US 3 1 7 1 Printer controller Fiery X3e sss 3 3 8 12 Printer controller MicroPress PrintLink 2020m 3 3 3 12 R Righit side doot eee eee Decet e eels 3 5 Right side door release lever sssem 3 5 S Space requirements
33. The paper being used is not compatible with the printer See 4 1 Paper Specifications for compatible types of paper p 4 1 The fusing unit requires replacement Contact your technical representative The printer takes too long to output prints The printer was in Energy Saver mode when the print command was issued If you do not want to use this mode disable it Contact your technical representative The printer setting was for color transparency transparency sheet or thick paper printing Wait a few moments 6 3 Troubleshooting CF2001P Appendix k 7 Appendix 7 1 Specifications Printer CF2001P Specification Type Desktop Photo conductor OPC Printing system Digital Full Color Printing Developing system NMT New Micro toning system Fusing system Belt fixing Resolution 600 dpi x 600 dpi Paper types Standard paper 17 02 to 23 94 Ibs 64 to 90 g m thick paper 1 1 24 21 to 43 36 Ibs 91 to 163 g m2 thick paper 2 2 43 62 to 55 59 Ibs 164 to 209 g m overhead projector transparencies postcards 1 Can only be fed through Tray 1 2 Thick paper 2 can be used for only postcards sizes Paper sizes Tray 1 12 25 x 18L 11 x 17L 11 x 14L LegalL LetterL LetterC ExcecutiveL ExcecutiveC 5 5 x 8 5L 5 5 x 8 5C 4 x 6L 1 A3WideL A3L A4L A4C ABL A5C AeL Tray
34. The use of non shield cables is likely to result in interference with radio communications and is prohibited under FCC rules INTERFERENCE CAUSING EQUIPMENT STANDARD ICES 003 IS SUE 3 For Canada Users This Class A digital apparatus complies with Canadian ICES 003 Cet appareil num rique de la classe A est conforme la norme NMB 003 du Canada CE Marking Declaration of Conformity for Users of the European Union EU This product complies with the following EU directives 89 336 EEC 73 23 EEC and 93 68 EEC directives This declaration is valid for the area of the European Union This device must be used with a shielded interface Parallel cable and shielded network 10 100BaseT cable The use of non shield cables is likely to result in interference with radio communications and is prohibited under 89 336 EEC rules 1 6 CF2001P Introduction 1 For users in countries subject to Class B regulations This device must be used with shielded interface Parallel cable and shielded network 10 100Base T cable The use of non shield cables is likely to result in interference with radio communications and is prohibited under CISPR 22 and local rules For users in countries not subject to Class B regulations WARNING This is a Class A product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures This device must be used with shielded
35. acity Cabinet 1 When Fiery X3e is installed printing from the manual bypass tray is not supported 2 The paper feed unit and large capacity cabinet are optional CF2001P 4 1 Print Paper Paper Sizes Standard paper Tray 1 O Tray 2 Manual bypass O tray O Ojoo O OJOJOO O OJOJOO O OJOO Paper Feed Unit O O OOJO O Large Capacity Cabinet Tray 1 O O O O O Tray 2 Manual bypass O O O O O tray O OJOJOO O OJOJOO Paper Feed Unit Large Capacity Cabinet 4 2 CF2001P Print Paper Paper Size A4C ABL A5C A6L 4 Paper Source Etc Tray 1 O O O O Tray 2 O Manual bypass O O O O tray Paper Feed O Unit Large Capacity O Cabinet 1 When Fiery X3e is installed printing from the manual bypass tray is not supported 2 The paper feed unit and large capacity cabinet are optional 3 For North America only 4 For Europe only CF2001P 4 3 Print Paper Paper capacity Paper Type Special Paper Standard Overhead Paper Source Paper Thick Thick Projector Etc Papert Paper2 Transpar posean encies Tray 1 250 sheets 20 sheets 20 sheets 20 sheets Tray 2 500 sheets 5 EV Manual bypass 1 sheet 1 sheet 1 sheet 1 sheet 1 sheet tray Pa
36. aper and then load the pa per so that the front side of the pa per the side facing up when the package was unwrapped faces down Lightly slide the paper into the feed slot as much as possible so that it is ready to be fed into the printer Do you need more information on feeding paper through the manual bypass tray Feed only one sheet of paper at a time Prints will be made on the surface of the paper facing down when itis loaded into the manual bypass tray 4 16 CF2001P Print Paper 4 Is a postcard loaded When loading a postcard load it as shown Do not load the postcard cross wise as shown Is the recommended overhead projector transparency MINOLTA CF300D loaded When loading the recommend ed overhead projector transpar ency MINOLTA CF300D load it as shown in the illustration CF2001P 4 17 Print Paper CF2001P Control Panel Messages k Control Panel Messages 5 5 1 Message List When a message appears in the control panel display refer to the section for details about the message and the action to be taken S Note The display window only displays two lines of a message at one time To view messages longer than two lines press w to display the next line of the message Message Cause Action Busy The printer is printing Wait for a while Check power of DT
37. aper in the drawer has been used 4 14 CF2001P Print Paper 4 3 Load paper into the left side of the drawer so that the front side of the paper the side facing up when the package was unwrapped faces up Has the paper been loaded cor rectly If the paper is not loaded cor rectly a paper misfeed may oc cur Make sure that the paper is not curled when it is loaded Do not load so much paper that the top of the stack is higher than the wmark Special paper cannot be fed from Tray 2 or optional paper feed units If you wish to make prints onto special paper feed it through Tray 1 When loading additional paper remove any paper remaining in the drawer place it on the new paper and then align the paper in the stack well before loading it into the drawer We recommend replenishing the paper only after all of the paper in the drawer has been used 4 Close the paper drawer CF2001P 4 15 4 Print Paper To load paper into the manual bypass tray Paper can be fed manually through the manual bypass tray if you wish to print onto paper that is not loaded into a drawer or if you wish to print onto special paper such as overhead transparencies postcards or thick paper 1 or 2 Note v When Fiery X3e is installed printing from the manual bypass tray is not supported 1 Open the manual bypass tray 2 Adjust the paper guides to the size of the p
38. careful not to touch the sur face of the paper take up roller with your hands If the roller has been touched wipe it with a dry cloth Paper take up roller 5 22 CF2001P Control Panel Messages 5 To clear a paper misfeed in the printer AN CAUTION Decreased print quality may result if the surface of the image trans fer belt at the bottom of the printer s fusing unit is touched Be careful not to touch the surface of the image transfer belt at the bot tom of the printer s fusing unit AN CAUTION The area around the fusing unit is extremely hot Touching anything other than the paper within the area around the fus ing unit may result in burns gt If you get burnt immediately cool the skin under cold water and then seek professional medical advice Pull up the lock release lever to open the right side door CF2001P 5 23 5 Control Panel Messages 2 Grasp the upper right side door as shown and then carefully open the door completely while making sure to support it Is the upper right side door be ing opened correctly Be sure to support the door while carefully opening it other wise it may be damaged 3 While moving the green lever on the inside of the upper right side door in the direction of the arrow carefully pull out the paper 4 Carefully pull out the paper 5 Move the two
39. ce of the paper take up roller with your hands If the roller has been touched wipe it with a dry cloth Paper take 2 Press down on the paper lifting plate until it locks into place 3 Slide the lateral guides to fit the size of paper to be loaded CF2001P Print Paper O For 12 1 4 x 18 or A3Wide pa per adjust the trailing edge guides as shown in the illustra tion 4 Load the paper into the drawer so that the front side of the paper the side facing up when the package was unwrapped faces up Has the paper been loaded cor rectly If the paper is not loaded cor rectly a paper misfeed may oc cur Donotload so much paper that the top of the stack is higher than the w mark Do not load more than 20 sheets of thick paper 1 overhead pro jector transparencies or postcards When loading additional paper remove any paper remaining in the drawer place it on the new paper and then align the paper in the stack well before loading it into the drawer We recommend replenishing the paper only after all of the paper in the drawer has been used CF2001P Print Paper Are postcards loaded When loading postcards load them as shown Do not load postcards cross wise as shown NOLTA CF300D loaded gt When loading the recommend ed overhead projector transpar encies MINOLTA CF300D load them as shown in t
40. d service representative If you keep on using it as is a fire or electrical shock could result Do not throw the toner cartridge or toner into an open flame The hot toner may scatter and cause burns or other damage eo AQA o Connect the power cord to an electrical outlet that is equipped with a ground ing terminal CF2001P 1 3 Introduction CAUTION Do not use flammable sprays liquids or gases near this product as a fire could result Do not leave a toner unit or drum unit in a place within easy reach of chil dren Licking or ingesting any of these things could injure your health Donotlet any object plug the ventilation holes of this product Heat could accumulate inside the product resulting in a fire or malfunction Donotinstall this product at a site that is exposed to direct sunlight or near an air conditioner or heating apparatus The resultant temperature changes inside the product could cause a malfunction fire or electrical shock Do not place the product in a dusty place or a site exposed to soot or Steam near a kitchen table bath or a humidifier A fire electrical shock or breakdown could result Do not place this product on an unstable or tilted bench or in a location subject to a lot of vibration and shock It could drop or fall causing personal injury or mechanical breakdown After installing this product mount it on a secure base If the unit moves or
41. de door FN7 9 Slide the finisher back against the printer Are the staples still jammed even after performing the above procedure Contact a qualified technical representative CF2001P 5 35 Control Panel Messages When the Message Service Code Cxxxx Appears When the message shown below appears in the control panel display a malfunction has occurred within this printer m m Ready Message Alert Service Code Cw Set_ Cancel Press W once and check which error code is displayed a a Ready Message Cw Menu Set_ Cancel If this message appears contact your technical representative and inform them of the error code that is indicated 5 36 CF2001P Control Panel Messages 5 5 6 When the Message xxxx unit near life limit Ap pears When it is almost time to replace a unit within this printer a message like the one shown below appears in the control panel When the message appears replace the unit according to your mainte nance agreement S Note The display window only displays two lines of a message at one time To view messages longer than two lines press v to display the next line of the message r3 pee Ready Message Alert xxxx unit oOo m Ready Message near life limit C4 I D Cy Cy Menu Set_ Cancel Menu Set CO Displayed Messages e
42. e seseeeeese 5 12 Clearing a Paper Misfeed and Staple Jam 5 16 To clear a paper misfeed in the manual bypass tray 5 18 To clear a paper misfeed in the duplex unit 5 20 To clear a paper misfeed in the paper feed unit 5 21 To clear a paper misfeed in the printer essseees 5 23 To clear a paper misfeed in finisher FN 107 FN 1068 5 26 To clear a paper misfeed in the 10 mailbin sorter 5 30 To clear jammed Staples ssseee em 5 33 When the Message Service Code Cxxxx Appears 5 36 When the Message xxxx unit near life limit Appears 5 37 When the Message Near troble XX XX Appears 5 38 Specifications cessisse nas anni kaarina nnn nnnnnt 7 1 Printer GF2001 P na citate tates dece 7 1 500 sheet Paper Feed Unit PF 118 sees 7 2 Large capacity Cabinet PF 117 sssee 7 3 Duplex Unit AD 14 aie a e aaaeei a anaE EASE aas 7 3 10 Mailbin Sorter JS 1002 sessseeeem e 7 4 Finisher EN 107 i rne Eh Hee ees 7 5 Finisher EN 108 n eee Eee PER ites 7 6 Care of the Printer eene 7 7 ju 7 7 HOUSING COVE 4i eade re pd n i e Pee pere coe estratti 7 7 Controlipan l bocce a t en RE a T
43. e toner unit developing roller and the PC drum as poor image quality could result Use the supplies and consumables recommended by the dealer Use of any supply or consumable not recommended could result in poor image quality and breakdown CF2001P 1 5 Introduction USER INSTRUCTIONS FCC PART 15 RADIO FREQUENCY DEVICES For U S A Users NOTE This equipment has been tested and found to comply with the lim its for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harm ful interference when the equipment is operated in a commercial environ ment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Oper ation of this equipment in a residential area is likely to cause harmful in terference in which case the user will be required to correct the interference at his own expense WARNING The design and production of this unit conform to FCC regu lations and any changes or modifications must be registered with the FCC and are subject to FCC control Any changes made by the purchaser or user without first contacting the manufacturer will be subject to penalty under FCC regulations This device must be used with a shielded interface Parallel cable and shielded network 10 100BaseT cable
44. een and Info XXXX appears in the display However a print operation is not performed until the printer has finished warming up after about 5 minutes at normal room temperature 68 F 20 C S Note s Message Ca Cy L Cancel XXXX indicates the name specified when the controller was set up For more details refer to the manual of the printer controller CF2001P 3 15 3 Before Making Prints Turning Off the Printer S Note If Fiery X3e is installed be sure to shut down the controller system before turning off the printer If MicroPress PrintLink 2020m is installed turn off the printer by performing just step 5 To turn off the printer 1 Check that Info XXXX appears in the display and then press the Menu button in the control panel Message Ca Ev Cancel 2 Press A or W until Functions Shut Down appears and then press the Set button ES r3 Ready Message Functions Shut Down Ca Cy Cancel 3 Press W once to display Shut Down Shut Down System and B a then press the Set button to begin Ready Message shutting down the system Shut Down Shut Down System I D cay cv Menu X Set Cancel 3 16 CF2001P Before Making Prints 4 When the system has finished shutting down
45. erious injuries or property damage Observe all cautions in order to ensure safe use of the printer CF2001P 1 9 Introduction S Note May also appear as Important or Tip Text highlighted in this manner contains useful information and tips to ensure safe use of the printer 1 The number 1 as formatted here in dicates the first step of a sequence of actions TS An illustration inserted here shows 2 Subsequent numbers as formatted what operations must be performed here indicate subsequent steps of a sequence of actions Text formatted in this style pro vides additional assistance Textformatted in this style describes the action that will ensure the desired results are achieved CF2001P Introduction 1 1 4 Explanation of Basic Concepts and Symbols The use of words and symbols in this manual are explained below Paper Feeding During printing paper is supplied from the right side of the printer and fed into the output tray on top or the output option at the left with the printed surface of the page facing down The paper feed direction is shown by the arrows in the diagram below CF2001P 1 11 Introduction Width and Length Whenever paper dimensions are men tioned in this manual the first value al ways refers to the width of the paper shown as A in the illustration and the second to the length
46. falls it may cause personal injury Donotstore toner units and PC drum units near a floppy disk or watch that are susceptible to magnetism They could cause these products to mal function The inside of this product has areas subject to high temperature which may cause burns When checking the inside of the unit for malfunctions such as a paper misfeed do not touch the locations around the fusing unit etc which are indicated by a Caution High Temperature warning label Do not place any objects around the power plug as the power plug may be dif ficult to pull out when an emergency occurs Always use this product in a well ventilated location Operating the product in a poorly ventilated room for an extended period of time could injure your health Ventilate the room at regular intervals Whenever moving this product be sure to disconnect the power cord and other cables Failure to do this could damage the cord or cable resulting in a fire electrical shock or breakdown When moving this product always hold it by the locations specified in the user manual or other documents If the unit falls it may cause severe per sonal injury The product may also be damaged or malfunction Remove the power plug from the outlet more than one time a year and clean the area between the plug terminals Dust that accumulates between the plug terminals may cause a fire Whenunplugging the power cord be sure to hold onto t
47. he illus tration mL 3 N gt A 3 Are the recommended overhead projector transparencies MI m L IH N gt NL lt i lt CF2001P 4 Print Paper 5 Slide the lateral guides against the edges of the paper O Make sure that the paper is not curled when it is loaded Check that the lateral guides are pushed up against the edges of the paper 6 Close the paper drawer N Turn the media type selection dial on the drawer to the setting for the type of paper loaded Are postcards loaded into Tray 1 If postcards 4 x 6 or A6 are loaded the paper type setting cannot be selected using the media type selection dial on the drawer Instead use the control panel buttons to select the paper size setting for postcards 4 x 6 or A6 4 10 CF2001P Print Paper To set the paper size for Tray 1 1 Check that Info XXXX appears in the display and then press the Menu button in the control panel fy P 2 Press A or V until Engine Setup appears and then press the Set button 3 Press A or V until the desired paper size appears and then press the Set button 4 Pre
48. he package was unwrapped faces up Have you loaded too much pa per into the drawer Do notload so much paper that the top of the stack is higher than the w mark Has the paper been loaded correctly Make sure to align the stack of paper a bad Do you wish to load a paper size or type different from that previ ously loaded For more details on changing the paper size and type refer to Loading Paper on page 4 7 5 4 CF2001P Control Panel Messages 4 Slide the lateral guides against the edges of the paper O Make sure that the paper is not curled when it is loaded Check that the lateral guides are pushed up against the edges of the paper 5 Close the paper drawer To load paper into Tray 2 or the 500 sheet paper feed unit 1 Pull out the paper drawer Has the paper take up roller been touched Be careful not to touch the sur face of the paper take up roller with your hands If the roller has been touched wipe it with a dry cloth 2 Press down on the paper lifting plate until it locks into place CF2001P Control Panel Messages 3 Load the paper into the drawer so that the front side of the paper the side facing up when the package was unwrapped faces up Have you loaded too much pa per into the drawer Do notload so much paper that the top of the stack is higher than the w
49. he plug Pulling on the power cord could damage the cord resulting in a fire or electrical shock 1 4 CF2001P Introduction Precautions for Routine Use Do not store toner units PC drum units and other supplies and consum ables in a place subject to direct sunlight and high temperature and humid ity as poor image quality and malfunction could result Do not attempt to replace the toner unit and PC drum unit in a place ex posed to direct sunlight If the PC drum is exposed to intense light poor im age quality could result Donot unpack a toner unit or PC drum unit until the very time of use Do not leave an unpacked unit standing Install it immediately or poor image quality could result Donotkeep toner units and PC drum units in an upright position or upside down as poor image quality could result Do not throw or drop a toner unit or PC drum unit as poor image quality could result Donotuse this product in an area where ammonia or other gases or chem icals are present Failure to do so may shorten the service life of the prod uct cause damage or decrease performance Do not use this product in an environment with a temperature outside the range specified in the user manual as a breakdown or malfunction could result Do not attempt to feed stapled paper carbon paper or aluminum foil through this product as a malfunction or fire could result Do not touch or scratch the surface of th
50. hould take precaution ZN 1 This symbol warns against possible electrical shock A diagonal line indicates a prohibited course of action S This symbol warns against dismantling the device e A black circle indicates an imperative course of action This symbol indicates you must unplug the device N WARNING Do not modify this product as a fire electrical shock or breakdown could result If the product employs a laser the laser beam source could cause blindness Do not attempt to remove the covers and panels which have been fixed to the product Some products have a high voltage part or a laser beam source inside that could cause an electrical shock or blindness Only use the power cord supplied in the package Failure to use this cord could result in a fire or electrical shock Useonly the specified power source voltage Failure to do that could result in a fire or electrical shock Donotuse a multiple outlet adapter to connect any other appliances or ma chines Use of a power outlet for more than the marked current value could result in a fire or electrical shock be Do not unplug and plug in the power cord with a wet hand as an electrical shock could result Plug the power cord all the way into the power outlet Failure to do this could result in a fire or electrical shock ee 1 2 CF2001P Introduction 1 Donot scratch abrade place a heavy object on heat twist
51. ht side door Opened when replacing the fusing unit or clearing misfeeds 3 6 CF2001P Before Making Prints Supplies and Parts No Part Name Description 1 Imaging unit Generates the printed image 2 Image transfer belt unit Layers onto the image transfer belt each of the single col ors of the image generated by the imaging unit in order to create a full color image 3 Image transfer roller Transfers onto the paper a full color image generated by unit the image transfer belt unit 4 Waste toner bottle Collects waste toner 5 Oil coating unit Supplies oil to the fusing roller 6 Fusing web unit Supplies oil to the fusing belt 7 Fusing unit Fuses the transferred toner to the paper 8 Ozone filter Collects the ozone generated in the printer 9 LED cleaning tool Used to clean the surface of the LED unit for example when replacing the imaging unit Store in a safe place for later use CF2001P 3 7 Before Making Prints Duplex Unit Optional nit Opened when clearing paper misfed within the duplex u c 5 S x Z dE nio e air CF2001P 3 8 Before Making Prints 10 Mailbin Sorter Optional No Part Name Description 1 Mailbins Paper is fed to the mailbin specified with the printer driver 2 Upper door Lower doo
52. ing apparatus not subjected to high humidity not extremely dusty F Store in a sealed plastic bag in a cool dark place paper that has been removed from its wrapper but not loaded into the printer Only use toner that has been manufactured specifically for this printer Never use other types of toner Keep all supplies out of the reach of children CF2001P Precautions AN CAUTION Precautions for handling toner gt Be careful not to spill toner inside the printer or get toner on your clothes or hands If your hands become soiled with toner immediately wash them with soap and water If toner gets in your eyes immediately flush them with water and then seek professional medical advice CF2001P Precautions CF2001P Before Making Prints 3 EE 3 Before Making Prints 3 1 Components and Their Functions The following describes each of the units that the printer is composed of as well as their functions e Printer Prints out the image received from the computer e 10 Mailbin sorter JS 1002 optional Feeds pages into the mailbin speci fied at the computer Note If Fiery X3e has been installed the 10 mailbin sorter is not operational CF2001P 3 1 Before Making Prints Finisher FN 107 FN 108 optional finishes pages according to the mode electronic sorting stapling or hole punching selected at the com
53. it through Tray 1 When loading additional paper remove any paper remaining in the drawer place it on the new paper and then align the paper in the stack well before loading it into the drawer We recommend replenishing the paper only after all of the paper in the drawer has been used Slide the lateral guides against the edges of the paper O Make sure that the paper is not curled when it is loaded Check that the lateral guides are pushed up against the edges of the paper Close the paper drawer CF2001P 4 Print Paper To load paper into the large capacity cabinet 1 Pull out the paper drawer 2 Load paper into the right side of the drawer so that the front side of the paper the side facing up when the package was unwrapped faces up Has the paper been loaded cor rectly If the paper is not loaded cor rectly a paper misfeed may oc cur Make sure that the paper is not curled when it is loaded Do not load so much paper that the top of the stack is higher than the wmark Special paper cannot be fed from Tray 2 or optional paper feed units If you wish to make prints onto special paper feed it through Tray 1 When loading additional paper remove any paper remaining in the drawer place it on the new paper and then align the paper in the stack well before loading it into the drawer We recommend replenishing the paper only after all of the p
54. ix 7 Finisher FN 107 Specification No of bins 2 Upper paper output tray Lower paper output tray Paper types Upper paper output tray Standard paper 17 02 to 23 94 Ibs 64 to 90 g m thick paper 24 21 to 55 59 Ibs 91 to 209 g m overhead projec tor transparencies postcards Lower paper output tray Standard paper 17 02 to 23 94 Ibs 64 to 90 g m2 Paper sizes Upper paper output tray 12 25 x 18L 1 11 x 17L 11 x 14L LegalL LetterL LetterC ExecutiveL ExecutiveC 5 5 x 8 5L 5 5 x 8 5C 4 x 6L A3WideL 2 A3L A4L A4C ABL A5C A6L Lower paper output tray 12 25 x 18L 11 x 17L 11 x 14L LegalL LetterL LetterC ExecutiveL ExecutiveC A3WideL A3L A4L A4C For US only For Europe only Nd Capacity of bins Upper paper output tray Standard paper 21 28 Ibs 80 g m Maximum 250 sheets Thick paper 24 21 to 55 59 Ibs 91 to 209 g m Maximum 20 sheets Overhead projector transparencies Maximum 1 sheet Postcards Maximum 20 sheets Lower paper output tray Standard paper 21 25 Ibs 80 g m LetterL or smaller maximum 3 000 sheets LegalL or larger maximum 1 500 sheets Staple setting Corner 11 x 17L 11 x 14L LegalL LetterL LetterC ExecutiveL Ex ecutiveC A3L A4L A4C Long edge 2 point LetterC ExecutiveC A4C Short edge 2 point 11 x 17L 11 x 14L A3L Punch setting Long edge 2 3 1 4 holes LetterC ExecutiveC 5 5 x 8 5C
55. m of the error code Sleep mode The printer has entered Tocancel Sleep mode Sleep mode send a print job or open and close a cover Tochangethe time forthe printer to enter Sleep mode contact a technical representative The guides in tray not set right The size of the paper loaded into tray is incorrect Load paper of an appropriate size into tray 5 2 CF2001P Control Panel Messages Message Cause Action To print clear 1st tray The upper paper output tray of the finisher is full of paper Remove paper from the upper paper output tray To print clear elevator tray The lower paper output tray of the finisher is full of paper Remove paper from the lower paper output tray To print clear mail bin The mail bin of the 10 mailbin sorter is full of paper Remove paper from the mail bin To print clear sorter area All bins in the 10 mailbin sorter are full of paper Remove all paper from the mailbins Warming up Warming up No action required Waste toner full Call service The waste toner bottle is full Ask your technical representative to refill the toner for the indicated color Waste toner full Please change The waste toner bottle is full Replace the waste toner bottle Waste toner nearly full The waste toner bottle will soon be full Replace the waste toner bottle as soon
56. malfunction occurred in the printer Contact your technical repre sentative and inform them of the error code No back staples The back staples have run out Install new back staples No front staples The front staples have run out Install new front staples No xxxx toner Call service The toner for the indicated color is empty Ask your technical representative to refill the toner for the indicated color No xxxx toner Please change The toner for the indicated color is empty Refill the toner for the indi cated color Paper jam at Jx A paper jam or staple jam occurred at the indicated location Remove the jammed paper or the jammed staple See page 5 16 Power save mode The printer has entered Energy Saver mode To cancel Energy Saver mode send a print job or open and close a cover Tochange the time for the printer to enter Energy Saver mode contact a technical representative Printing stopped Paper is loaded into the manual bypass tray Remove all paper from the manual bypass tray A communication error occurred No action required Printing suspended Printing has been stopped No action required Replace Trans Belt Unit The service life of the transfer belt unit has expired Replace the transfer belt unit Service Code An error occurred Contact your technical Cxxxx representative and inform the
57. mark Has the paper been loaded correctly Make sure to align the stack of paper CREER Do you wish to load a paper size or type different from that previ ously loaded For more details on changing the paper size and type refer to Loading Paper on page 4 7 4 Slide the lateral guides against the edges of the paper O Make sure that the paper is not curled when it is loaded Check that the lateral guides are pushed up against the edges of the paper 5 Close the paper drawer CF2001P Control Panel Messages To load paper into the large capacity cabinet 1 Pull out the paper drawer Load paper into the right side of the drawer so that the front side of the paper the side facing up when the package was unwrapped faces up Have you loaded too much pa per into the drawer Do notload so much paper that the top of the stack is higher than the w mark Load paper into the left side of the drawer so that the front side of the paper the side facing up when the package was unwrapped faces up Have you loaded too much pa per into the drawer Do notload so much paper that the top of the stack is higher than the w mark Close the paper drawer CF2001P Control Panel Messages When the Message Xxxx toner nearly empty Appears S Note Do not refill the toner until the message indica
58. nntnnnnn 1 1 Warning and Precaution Symbols eee 1 2 Meaning of Symbols enne 1 2 LZ ollcm 1 2 GALTON EET 1 4 Precautions for Routine Use sessseee 1 5 USER INSTRUCTIONS FCC PART 15 RADIO FREQUENCY DEVICES For USA Users ioci Eten petere dE 1 6 INTERFERENCE CAUSING EQUIPMENT STANDARD ICES 003 ISSUE 3 For Canada Users sss 1 6 CE Marking Declaration of Conformity for Users of the European Uic 1 6 For users in countries subject to Class B regulations 1 7 For users in countries not subject to Class B regulations 1 7 Ozone Rele se dri tite ee ee LO rm se ERR RERO Rx x AB 1 7 WARNING LABEL sese eene nennen 1 8 LED Radiation Safety ssssseeee 1 8 Guide to Manuals eeeeeeeeeeeeeee eene nennen nnn 1 9 Enclosed Mariuals tienne etie tera Deren EARE 1 9 Explanation of Manual Conventions eene 1 9 Explanation of Basic Concepts and Symbols 1 11 Paper Feedirig euo p iden denn 1 11 Width and Lengi P 1 12 Paper Orientation essen nennen nen 1 12 aunq eee 1 13 2 Precautions 2 1 Installation Precautions eese 2 1 Installati n Sites i iret nee orient iiie tes er hene ordei
59. onsumption Less than 17 W Dimensions W 5 47 in 139 mm D 17 32 in 440 mm H 14 37 in 365 mm Weight About 6 38 Ibs 3 1 kg 7 3 Appendix 10 Mailbin Sorter JS 1002 Specification No of bins 10 Paper types Bint Standard paper 17 02 to 23 94 Ibs 64 to 90 g m thick pa per 24 21 to 55 59 Ibs 91 to 209 g m overhead projector transparencies postcards Bin2to Bin 10 Standard paper 17 02 to 23 94 Ibs 64 to 90 g m2 Paper sizes Bint 12 25 x 18L 11 x 17L 11 x 14L LegalL LetterL LetterC ExecutiveL ExecutiveC 5 5 x 8 5L 5 5 x 8 5C 4 x 6L 5 A3WideL A3L A4L A4C ABL A5C AGL For US only 2 For Europe only Bin2to Bin 10 11 x 17L 11 x 14L LegalL LetterL LetterC ExecutiveL Ex ecutiveC 5 5 x 8 5L A3L A4L A4C ABL Capacity of bins Bint Standard paper 21 28 Ibs 80 g m Maximum 200 sheets Thick paper 24 21 to 55 59 Ibs 91 to 209 g m Maximum 20 sheets Overhead projector transparencies Maximum 1 sheet Postcards Maximum 20 sheets Bin 2 to Bin 10 Standard paper 21 28 Ibs 80 g m Maximum 200 sheets bin Total 2 000 sheets Power source Supplied from printer Power consumption Less than 32 W Dimensions W 21 81 in 554 mm D 20 15 in 512 mm H 34 4 in 874 mm Weight Main unit about 63 93 Ibs 29 kg Horizontal transport unit 8 81 lbs 4 kg 7 4 CF2001P Append
60. per Feed Unit 500 sheets n Large Capacity 2 500 Cabinet sheets 1 When Fiery X3e is installed printing from the manual bypass tray is not supported 2 The paper feed unit and large capacity cabinet are optional Recommended paper Paper Type Recommended Paper Standard Paper For full color prints CF80 Hammermill Laser Print New Radiant White Color Copy 90 2 For black and white prints MINOLTA bond MINOLTA bond IV Original Thick Paper 1 CF105 NS 700 Thick Paper 2 NS 1000C Overhead Pro For full color prints CF 300D jector Transpar z encies For black and white M 100D prints 1 The paper is available for North America only 2 The paper is available for Europe only 4 4 CF2001P Print Paper 4 Paper Types To Be Avoided The following types of paper should not be used otherwise decreased print quality paper misfeeds or damage to the printer may occur Overhead transparencies that have already been fed through the printer even if the transparency is still blank e Paper that has been printed on by a heat transfer printer or an inkjet printer Paper that is either extremely thick or extremely thin Folded rolled wrinkled or torn paper Perforated paper or paper with holes punched in it Extremely smooth or extremely rough paper or paper with an uneven surface Paper that ha
61. printer off rici eripe eterne ee eats 3 14 Turning On the Printer eene 3 15 Turning Off the Printer eee 3 16 Totum off the printer recedente rient 3 16 3 5 X Total Counter oe 3 18 To print the total counter sseseeeen 3 18 4 1 Paper Specifications eese eene ennt 4 1 Papet Typ6 i re Pe een ete 4 1 Paper Sizes p 4 2 Paper Types To Be Avoided sse 4 5 4 2 Print Area uiui euenire 4 3 Paper Storage 4 4 Loading Paper To load paper into Tray 1 250 sheet multipurpose tray 4 7 To set the paper size for Tray 1 sse 4 11 To load paper into Tray 2 or the 500 sheet paper feed unit 4 12 To load paper into the large capacity cabinet 4 14 To load paper into the manual bypass tray uses 4 16 ii CF2001P o 5 1 5 2 5 3 5 4 7 2 Message List 1e ien Idas uiii 5 1 To load paper into Tray 1 250 sheet multipurpose paper drawer esee 5 4 To load paper into Tray 2 or the 500 sheet paper feed unit 5 5 To load paper into the large capacity cabinet 5 7 When the Message Xxxx toner nearly empty Appears 5 8 To add toner ine Em oen 5 9 When the Message No xxxx staples Appears 5 12 To replace the staple cartridg
62. r Opened when clearing paper misfed within the sorter 3 Horizontal transport Transports prints to the sorter or finisher unit 4 Horizontal transport Opened when clearing paper misfed within the horizontal unit cover transport unit CF2001P Before Making Prints Finisher Optional No Part Name Description Upper cover Opened when clearing paper misfed within the finisher Upper paper output tray Collects printouts on special paper overhead projector transparencies thick paper 1 thick paper 2 and postcards Lower paper output tray Collects printouts on normal paper Front door Opened when clearing paper misfed within the finisher Right side door Finisher FN 107 only Opened when replacing the staple cartridge or clearing pa per misfeeds 3 10 CF2001P Before Making Prints Paper Feed Unit Optional No Part Nam Description 1 Side doo Opened when clearing paper misfeeds 2 Tray 3 Holds 500 sheets of paper The paper size can be adjusted freely 3 Tray 4 As many as two units can be installed See p 4 12 CF2001P 3 Before Making Prints Large Capacity Cabinet Optional No Part Name Description 1 Side door Opened when clearing paper misfeeds 2 Large Capacity Holds 2 500 sheets of paper
63. r output tray Standard paper 21 25 Ibs 80 g m LetterL or smaller maximum 1 000 sheets LegalL or larger maximum 500 sheets Staple setting Corner 11 x 17L 11 x 14L LegalL LetterL LetterC ExecutiveL ExecutiveC A3L A4L A4C Power source Supplied from printer Power consumption Less than 63 W Dimensions W 21 18 in 538 mm D 24 76 in 629 mm H 38 50 in 978 mm Weight About 86 42 Ibs 39 2 kg Accessories 1 staple cartridge 3 000 staples CF2001P Appendix 7 7 2 Care of the Printer Cleaning Turn the printer off before cleaning it Housing cover Clean the surface of the housing cover by wiping it with a soft cloth dampened with a mild household detergent 4 d Control panel Clean the control panel by wiping it with a soft dry cloth N AN CAUTION Incorrectly cleaning the control panel may damage them Never use mild household detergent or glass cleaner to clean the control panel CF2001P 7 7 Appendix CF2001P Index EE 8 Index Numerics 10 Mailbini SOrter i retenir Eve keine iocos 3 1 3 9 7 4 500 sheet Paper Feed Unit sese 7 2 Care of the Printer 3 erect nts 7 7 COMMON PAMOl t 3 5 Cancel DUOI e 3 13 Display WIBOOW ien ine ace einen eee es 3 13 Menu DURON C iacta 3 13 Message light iid Eee ees 3 13 Message LIS qM EI
64. s been treated such as carbon backed paper or heat sensitive or pressure sensitive paper Paper that has been decorated with foil or embossing Paper of various sizes Paper of a non standard shape not rectangular Paper that is bound with glue staples or clips Paper with labels attached Paper with ribbons hooks buttons etc attached CF2001P 4 5 4 Print Paper 4 2 Print Area When using a printer controller to print from a computer any part of the original image within the areas indicated below is not printed The sizes of the paper margins differ according to the controller that is used B A C E Paper output direction Fiery X3e MicroPress PrintLink 2020m C L A 0 2 in 5mm A 0 2 in 6 mm s B 0 2 in 5 mm B 0 2 in 5 mm C 0 12 in 3 mm C 0 2 in 5 mm 4 3 Paper Storage Observe the following precautions when storing the paper F Store the paper in a location that meets the following requirements Not exposed to direct sunlight Not exposed to fire Not exposed to high humidity Not extremely dusty Unwrapped paper should be stored in a plastic bag in a cool dry loca tion Keep paper out of the reach of children 4 6 CF2001P Print Paper 4 4 Loading Paper To load paper into Tray 1 250 sheet multipurpose tray 1 Pull out the paper drawer for Tray 1 Has the paper take up roller been touched Be careful not to touch the sur fa
65. ss the Cancel button E E Ready Message ar wm Cy Cancel o Ready Message Functions Engine Setup Menu X Set Cancel r3 E Ready Message 1st Tray Setup LETTER Lx Cy Cancel CF2001P Print Paper To load paper into Tray 2 or the 500 sheet paper feed unit 1 Pull out the paper drawer 9 Has the paper take up roller been touched Be careful not to touch the sur face of the paper take up roller with your hands If the roller has been touched wipe it with a dry cloth 2 Press down on the paper lifting plate until it locks into place 3 Remove the trailing edge guide and then re install it for the size of paper to be loaded 4 Slidethe lateral guides to fit the size of paper to be loaded Paper take up roller CF2001P Print Paper 5 7 Load the paper into the drawer so that the front side of the paper the side facing up when the package was unwrapped faces up Has the paper been loaded cor rectly If the paper is not loaded cor rectly a paper misfeed may oc cur Do not load so much paper that the top of the stack is higher than the wmark Special paper cannot be fed from Tray 2 or optional paper feed units If you wish to make prints onto special paper feed
66. t if the surface of the image trans fer belt at the bottom of the printer s fusing unit is touched Be careful not to touch the surface of the image transfer belt at the bot tom of the printer s fusing unit 1 Pull up the lock release lever to open the right side door 2 Carefully pull out the paper 5 18 CF2001P Control Panel Messages 3 Close the right side door CF2001P Control Panel Messages To clear a paper misfeed in the duplex unit 1 Open the duplex unit door 2 Carefully pull out the paper 3 Close the duplex unit door CF2001P 5 20 Control Panel Messages 5 To clear a paper misfeed in the paper feed unit 1 Open the lower right side door 2 Turn the green wheels to feed the paper so that it can be easily re moved 3 Carefully pull out the paper 9 Is the large capacity cabinet installed While turning the green dial in the direction of the arrow care fully pull out the paper CF2001P 5 21 5 Control Panel Messages 4 Close the lower right side door 5 Pull out the paper drawer being used and then remove any paper remaining in the drawer 6 Load the paper in the drawer again and then close the drawer 9 Has the paper take up roller been touched Be
67. ting that Xxxx toner nearly empty appears on the control panel display In addition do not refill the toner of any color other than the one indicated in the message on the control panel A CAUTION Be careful not to spill toner inside the printer or get toner on your clothes or hands f toner gets on your hands wash them using water and a neutral soap f toner gets in your eyes immediately rinse them and then consult a medical professional A CAUTION Precaution for the disposal of the used toner bottle Do not throw away the used toner bottle instead keep it to be collect ed by your technical representative A WARNING Precautions for handling toner and the toner bottle gt Do not throw toner or the toner bottle into a fire Toner expelled from the fire may cause burns CF2001P Control Panel Messages 5 To add toner Open the toner supply door and then open the toner hopper lid for the toner that you wish to refill O For example If the yellow toner is empty open the leftmost ton er hopper lid 2 With the opening of the new toner bottle pointing up hit the bottom of the bottle against a strong surface such as a desk or table four or five times from a height of about 4 in 10 cm Since the toner within the V bottle may have become NM compacted be sure to break it up by performing this step Is the toner bottle being held

Minolta CF2001P Printer User Manual

Contents

Download Pdf Manuals

Related Search

Related Contents