M-Audio AP-012403 Network Card User Manual
Contents
1. Possible Cause 2 Your application software may not have the proper audio buffer sizes set Each software application handles this differently but typically there is somewhere in the software s setup to set the size of the playback and recording buffers used by the application Some applications also require you to run a calibration sometimes called profiling the first time you use the software with a new audio interface For instance if the clicks are present when using Cakewalk SONAR then try to run SONAR s Wave Profiler Possible Cause 3 Some accelerated graphics cards use excessive amounts of system bandwidth preventing the recording buffer of an audio interface from keeping up with demand This can cause clicks in the recording Reducing or turning off the graphics card s graphics acceleration feature often resolves this problem In Windows the level of graphics acceleration is accessed from Start Settings Control Panel System Performance Graphics Problem My software application keeps telling me sample rate not supported or some similar message Possible Cause This would most likely occur if you were trying to select 96000Hz as a sample rate and the Maximum Sample Rate available from the Audiophile USB Control Panel is 48000 Open the control panel and uncheck the Active Port boxes until you have only one port selected for either input or output 19 Problem I am playing AC 3 or surround sound d2. Audiophile MIDI driver as the default Windows MIDI driver by clicking on the Out USB Audiophile entry in the drop down list then selecting OK or Apply Macintosh Sound Manager and the Audiophile USB The Macintosh Sound Manager will allow you to select the Audiophile USB as the system s audio input and output device Open the Apple menu and select Sound from the Control Panels list Then choose Audiophile as both input and output driver However you may also leave the Sound control panel set to Built in if you wish to use the Audiophile only with your music program and use the internal audio for system sounds Audiophile USB Inputs amp Outputs The Audiophile USB Digital Recording Interface s analog inputs and outputs are compatible with a variety of audio products The Audiophile USB has both female RCA and female 1 4 TS tip sleeve input jacks and female RCA output jacks These jacks allow connection to unbalanced typically consumer or semi pro line level equipment Only one pair of analog inputs can be used at any given time When a 1 4 TS plug is connected to the 1 4 line inputs the corresponding RCA input jack is defeated If you have RCA cables connected to the Audiophile and then connect 1 4 plugs to the 1 4 jacks the Audiophile will then get its signal from the 1 4 line inputs NOTE In order to preserve its high dynamic range and minimize distortion the Audiophile USB does
3. Out USB MIDI In MIDI Out MIDI Out MIDI In Front Rear Keyboard Synth Audiophile USB Computer Sound System 17 Troubleshooting Problem No sound output Possible Cause 1 The Audiophile USB hardware or software device drivers are not properly installed See the installation sections of this manual for further information Possible Cause 2 There is a resource conflict between your computer s USB controller and another device in your computer PC only Check the Device Manager for your USB controller s IRQ against those of the other installed devices If necessary change the settings for the one or more of the devices refer to your computer or motherboard manual Possible Cause 3 Your application software has not been properly configured to use the Audiophile USB as its audio output device Possible Cause 4 Improper connections of the audio accessories Verify that the Audiophile USB analog audio outputs are properly connected to a digital mix deck or external mixer amplifier or the S PDIF Out is connected to an external digital audio device capable of receiving S PDIF Problem I m trying to record digital audio through the S PDIF input but I don t hear any output Possible Cause The settings in the Audiophile Control Panel may be incorrect Double check that you have S PDIF Input enabled and that your settings don t exceed the bandwidth limitations of USB Remember that the more inputs and
4. are done You may now exit OMS Setup by quitting the application Macintosh OS X Installation 1 Insert the Audiophile USB Driver CD into your CD ROM Drive and open the CD to view its contents 2 Double click M Audio Audiophile USB Installer dmg file An Icon will appear on your desktop marked Audiophile USB 3 Double click the Audiophile USB icon on your desktop 4 Now double click on the M Audio Audiophile USB Installer mpkg 5 You will need your Administrator Password for the next step To continue click the lock icon in the lower left corner of the window that states Click The Lock To Make Changes 6 Enter your password and click OK 7 The next window Welcomes You to the installation process Click Continue 8 Select your OS X hard drive Click Continue 9 When prompted click Upgrade to continue 10 When prompted click Continue Installation 11 When prompted click Restart to finish the installation 12 After the computer has restarted now plug the Audiophile USB into your computer s USB Port 8 13 Go to System Preferences in the Apple Menu Select the Sound preference panel and click the Output tab Select M Audio Sonica Theater to choose the Sonica Theater as your default output device Mac OS X Installation is now complete Proceed to the next section Hardware Installation Verifying Windows Driver Installation Windows displays the Audiophile USB driver status in
5. as stereo pairs but allow you to pan audio left or right within the pair Therefore to send a mono output to the Audiophile s Left Output for example choose M Audio USB Audiophile Line and pan that track hard left To send a mono output to the Audiophile s Right Output choose M Audio USB Audiophile Line and pan that track hard right 15 ASIO Input and Output Devices If your music program is ASIO compliant you may use the USB Audiophile ASIO driver with your Audiophile USB Open your music program and go to the audio setup page The USB Audiophile ASIO driver will show up in the program s ASIO Driver list allowing you to select it at this time if it is not already selected by default If you are using an ASIO compliant music program we suggest that you enable and use the Audiophile s ASIO drivers ASIO gives you the advantage of being able to monitor your source through the program similar to monitoring the record inputs of a tape machine ASIO input devices will appear as M Audio USB Audiophile Line Left M Audio USB Audiophile Line Right M Audio USB Audiophile SPDIF Left and M Audio USB Audiophile SPDIF Right ASIO Output devices will appear as these stereo pairs which you will be able to pan left and right from within your music program M Audio USB Audiophile Line and M Audio USB Audiophile SPDIF Once the Audiophile USB ASIO driver is selected in your mu
6. can be launched from any of the above locations Once the Audiophile USB Control Panel software has been opened you will see the various controls for enabling inputs and outputs and for setting other parameters NOTE When using a music software program that is ASIO capable launch the Audiophile USB Control Panel software from within that program If you need to change the master clock settings for instance in other words change from the Audiophile s internal clock to an external clock by selecting S PDIF In from the control panel it is desirable to launch the music program first and then the Audiophile USB Control Panel from the program s launch or control panel button Without the music program open however it is okay to open the Audiophile USB Control Panel from your desktop or other location The Audiophile USB Control Panel Certain audio settings are made in the USB Audiophile Control Panel and are important to the way the Audiophile performs You may never need to change them for your particular purposes but it s good to know how these settings affect what you do and how they interact When the Audiophile USB driver and control panel software are first installed a default setting is created that will work for you in most circumstances The analog inputs are active as well as the analog outputs and the S PDIF output The S PDIF Input is left unchecked The 16 bit radio button is selected but c
7. click Next to continue 28 7 A Digital Signature Not Found window will appear As this is a relatively new product it has does not have an official Windows Digital Signature yet Rest assured our USB drivers are of the highest quality and will not cause problems in your system Click Yes 8 An M Audio Setup window will appear next Make sure both Enable Digital CD and Enable DMA Transfer Mode boxes are checked then click Next 9 An M Audio Setup window will come up confirming a successful setup Click Next to successfully install the USB Audiophile 29 10 Windows will prompt you to restart the computer Make sure that Yes restart my computer now is checked and then click Finish to restart 11 When you are completely restarted and at the desktop power up the USB Audiophile 12 A Digital Signature Not Found window will appear next Click Yes 13 A second Digital Signature Not Found Box will appear Click Yes again 30 14 The driver is now installed in your computer Next open the Windows Control Panel and click on the Audiophile USB Control Panel Select Place Audiophile Icon in the task bar A button which contains a small black M and represents the Audiophile USB control panel will now appear in the system tray for easy control panel access Windows ME NOTE Please make sure the Service Pack 3 is installed To get this update please visit the download
8. is capable of 48kHz or 44 1kHz or lower sampling rates at either 24 or 16 bits When you uncheck and deactivate any one of the Active Ports the 24 bit option will become available If you select the 24 bit radio button and then activate all four Active Ports the control panel will automatically switch back to the 16 bit setting and gray out the 24 bit option NOTE Please exit any audio applications running before switching between bit depths The Audiophile USB will perform at 96kHz sampling rate with any one of the stereo pairs enabled and with the 24 bit Sample Depth selected This is most useful if your CD DVD player is capable of playing audiophile 96kHz recordings The Audiophile USB will not operate at 96kHz when the control panel is set to 16 bits In the example below Output 1 amp 2 is enabled and 24 bit Sample Depth is selected with the Maximum sample rate showing 96kHz 11 If you activate both sets of input and output channels you will notice that the 24 bit setting in the Sample Depth column is grayed out and the Maximum sample rate is shown as 48000 Hz NOTE Whenever S PDIF Input is selected as an Active Port the Audiophile is expecting a digital signal at that port and to lock to the sample rate of that signal When S PDIF Input is selected and there is no signal present at the S PDIF Input port or the S PDIF signal is not recognized or invalid the Audiophile USB will not operate properly Most likely you w
9. outputs you have enabled the lower the allowable sampling rate and bit depth Problem The Device Volume control in Windows Sounds and Audio Devices or other software such as MUSICMATCH Jukebox is grayed out and does not function Possible Cause Audiophile USB does not make its volume control parameter available to the host computer s operating system Use the Head Phone Level and Output Level knobs on the front panel of your Audiophile to adjust volume Problem No visual activity on Audio Input volume VU meters of user software Possible Cause 1 The Audiophile USB input devices are not properly selected in the user s application software Possible Cause 2 Improper connections to audio accessories 18 Problem Repetitious Sound Possible Cause An IRQ resource conflict with the USB controller and another device PC only Often this will result in a small segment of sound 0 5 to 1 second repeating itself over and over sometimes completely locking up the computer See the general troubleshooting suggestions at the beginning of this section Problem I m getting some pops and clicks in my audio recording Possible Cause 1 Input levels are too hot causing clipping or input distortion Make sure you have the proper signal levels coming from your source audio device and lower the output if necessary The incoming levels may be easily viewed from the Audiophile USB Control Panel peak meters
10. product by sending in the completed warranty card This warranty explicitly excludes power supplies and included cables which may become defective as a result of normal wear and tear In the event that M Audio receives written notice of defects in materials or workmanship from such an original purchaser M Audio will either replace the product repair the product or refund the purchase price at its option In the event any repair is required shipment to and from M Audio and a nominal handling charge shall be borne by the purchaser In the event that repair is required a Return Authorization number must be obtained from M Audio After this number is obtained the unit should be shipped back to M Audio in a protective package with a description of the problem and the Return Authorization clearly written on the package In the event that M Audio determines that the product requires repair because of user misuse or regular wear it will assess a fair repair or replacement fee The customer will have the option to pay this fee and have the unit repaired and returned or not pay this fee and have the unit returned unrepaired The remedy for breach of this limited warranty shall not include any other damages M Audio will not be liable for consequential special indirect or similar damages or claims including loss of profit or any other commercial damage even if its agents have been advised of the possibility of such damages and in no event will M A
11. section of Microsoft at www microsoft com Windows ME comes installed with DirectX version 7 You must have DirectX version 8 1 in order to install the Audiophile USB The Audiophile USB installer will automatically check for the correct version of DirectX and install the latest DirectX update This update will be skipped if you already have DirectX version 8 1 or higher in your system 1 During this installation the Audiophile USB must be powered off Begin the installation process by inserting the Drivers CD ROM in your computer and double click on the Audiophile USB EXE icon in the Window that appears The installer will now check your computer for the correct version of DirectX If DirectX version 8 1 or higher is already installed proceed directly to step number 6 2 Assuming that the installer has not found Direct X 8 1 or higher it will now install DirectX version 8 1 Proceed with the DirectX installation by clicking Next 31 3 Verify that you wish to continue installing DirectX 8 1 by clicking Yes 4 Verify that you have read the license agreement and agree to the terms Click Yes to continue 5 Windows will need to restart your machine to complete the DirectX 8 1 installation Click OK to restart your system 6 This is the first setup window for installing the Audiophile USB drivers after the installer has confirmed that you have DirectX version 8 1 or higher installed on your system Make sure you
12. MS Configuration for more information on installing and configuring OMS 1 Insert the Drivers CD into your CD ROM drive Locate and open the Audiophile USB folder Open the folder for your current Macintosh OS and double click on the Installer program in that folder 2 As the Installer loads the Audiophile USB drivers you will be asked if you wish to place a shortcut to the Audiophile USB Control Panel on your desktop This is your choice but it s probably a good idea to choose this option You can always trash the shortcut if you find it unnecessary 3 After you run the Installer you may switch On your Audiophile USB Your Audiophile USB is now ready for action OMS Configuration To configure the Audiophile USB for MIDI on Mac OS 9 x you will need to have Opcode s OMS Open Music System installed first OMS is a MIDI Manager program and it is necessary to install this in order to run all OS 9 music programs that have a MIDI engine i e programs that use MIDI You need to install OMS before you run the Audiophile USB s driver Installer program OMS is provided on the Drivers CD that came with the unit and is located in the OS 9 folder or it can be downloaded from the M Audio Website s Drivers page Opening the OMS 2 3 8 folder and double clicking on the Install OMS 2 3 8 program will install OMS in your system Restart your computer and continue with the driver installation see previous secti
13. SB Control Panel 10 Windows Sound System and the Audiophile USB 12 Macintosh Sound Manager and the Audiophile USB 13 Audiophile USB Inputs amp Outputs 13 Audiophile USB with Your Music Software 14 Audiophile USB MIDI Setup 16 Troubleshooting 17 Audiophile USB Warranty 20 Appendix A Technical Specifications 21 Appendix B Driver Software Install Step by Step 22 Windows XP 23 Windows 2000 27 Windows ME 31 Limited One Year Warranty 34 Audiophile USB Owner s Manual version AP 012403 Introduction Congratulations on your purchase of the Audiophile USB by M Audio The Audiophile USB is your audio and MIDI upgrade for any PC or Macintosh computer utilizing the convenience of your comput
14. Table of Contents Introduction 2 What s in the Box 2 About the Audiophile USB 2 Features amp Specifications 3 Minimum System Requirements 3 Front Panel Features 4 Rear Panel Features 4 Guide to Getting Started Quickly 5 Hardware Installation 5 Audiophile USB Driver amp Software Installation 6 Windows Installation 6 Macintosh OS 9 Installation 7 OMS Configuration 7 Macintosh OS X Installation 8 Verifying Windows Driver Installation 9 Verifying Control Panel Installation PC Macintosh 9 The Audiophile U
15. an be switched to 24 bit if you wish to record at that bit depth from your music program The Audiophile is capable of recording at sample rates up to and including 48000Hz You should only check the S PDIF Input port if you are recording audio from the S PDIF Input or otherwise wish to synchronize to an external 10 sampling clock Continue reading this section for more information on making selections in the Audiophile USB Control Panel Active Channels amp Sample Depth Activation of the Analog and S PDIF inputs and outputs is done with a set of four check boxes Two radio buttons allow selection between sample bit depths of 16 bit or 24 bit These settings will interact with each other either expanding or limiting your Active Ports Sample Depth and or Maximum Sample Rate settings Using the full USB bandwidth will allow for 4x4 audio streams at 16 bits with a sampling rate of 48kHz or below A higher bit depth or sampling rate will demand a trade off from your system which can be achieved by disabling your Active Ports On the right side of the control panel there are two columns labeled Active Channels Analog and S PDIF inputs and outputs and Sample Depth 16 bit and 24 bit Choosing the 24 bit setting will allow your music program to record at any bit depth up to 24 bit depending on the variety of selections within that program With any combination of three stereo pair Active Ports enabled the Audiophile USB
16. ata from a software application on my computer sending the data from Audiophile USB S PDIF Out to my home theater s AC 3 decoder However the decoder does not recognize the signal and therefore refuses to put out any audio Possible Cause There is a bit within the S PDIF digital audio stream that defines the S PDIF content as audio or non audio Most AC 3 surround sound decoders expect this setting to be non audio and will otherwise reject the information Go to the S PDIF page of the Audiophile USB Control Panel select Consumer and Advanced Settings and then select DD DTS Pass Thru Problem I have Windows 98SE and I want to install the Audiophile USB why do I need the original operating system CD ROM to install your drivers Answer Windows 98SE does not have the system files to support USB Audio installed as part of the core installation Instead these files must be added The necessary files are located on the Windows 98SE CD If you do not have your original Windows 98SE CD contact Microsoft Technical about how to acquire the files for USB Audio support in Windows 98SE 20 Audiophile USB Warranty M Audio warrants that this product is free of defects in materials and workmanship under normal use for a period of One 1 year so long as the product is owned by the original purchaser the original purchaser has proof of purchase from an authorized M Audio dealer and the purchaser has registered his her ownership of the
17. ayers select the S PDIF option in the DVD players audio setup page and your computer becomes a high end home theater player in conjunction with the Audiophile USB Audiophile USB with Your Music Software Once the Audiophile USB hardware and software drivers are properly installed the Audiophile is ready for use with your music application software Some software applications may require you to highlight or enable the Audiophile USB drivers within the program in order to use the Audiophile while others may have a utility that analyzes or profiles the audio devices in your system and enables the drivers Your software should have an audio device driver setup page If you have problems locating it consult your software s documentation The Audiophile drivers include MME and WDM drivers for Windows ASIO drivers for both Windows and Mac and Sound Manager drivers for Mac WDM drivers are a more modern driver architecture for Windows operating systems Me 2000 and XP but only certain programs like Cakewalk s Sonar will take advantage of them Other Windows programs will automatically access and use the MME drivers WDM drivers similar to ASIO will give you 14 low latency monitoring through the application check your application s documentation for information regarding input monitoring If your Windows or Macintosh program is ASIO compliant like Steinberg s Cubase or Emagic s Logic then the program s a
18. capable Dolby DTS etc making the Audiophile USB the perfect high end sound interface for digital recording analog or digital transfers mixing and mastering as well as DVD and home theater applications The Audiophile USB allows you to connect a line level signal from your line level instrument mixer or pre amp into the Audiophile s analog 1 4 phone 2 jacks Alternatively you can connect the record outputs of your stereo receiver into the Audiophile s RCA jacks located on the back panel Record a digital audio signal from your DAT MiniDisc CD or external A D converter via the Audiophile s coaxial S PDIF input Control all hardware settings with the Audiophile USB Control Panel software The Audiophile USB also includes MIDI I O connectors Provided are one input and one output for use with external MIDI equipment such as sound modules and drum machines The MIDI I O may also be used to synchronize your computer to external devices via MIDI time code Features amp Specifications 24 bit 96kHz full duplex recording interface with MIDI I O Two 2 analog inputs accept common unbalanced audio connections on 1 4 or RCA jacks Two 2 analog outputs with level control provide common unbalanced audio connections on RCA jacks Two 2 channels of coaxial RCA S PDIF I O 1x1 16 channel MIDI I O Headphone output with level control High analog dynamic range D A 107dB A D 109 dB bot
19. d that the proper power supply is attached correctly This is the power On position To switch power Off press in and release this switch to the out position Rear Panel Features 1 Left Input and Right Input 1 4 Analog Inputs These jacks input analog audio from a variety of external sources Each jack is female 1 4 tip sleeve compatible with common male 1 4 TS cables When plugs are inserted into these jacks the RCA inputs are defeated 4 2 Left Input and Right Input RCA Analog Inputs These jacks input analog audio from a variety of external sources Each jack is female RCA compatible with common male RCA cables When plugs are inserted into the 1 4 jacks these RCA inputs are defeated 3 Left Output and Right Output RCA Analog Outputs These jacks output analog audio to a variety of external destinations Each jack is female RCA compatible with common male RCA cables 4 S PDIF In This RCA connector receives a S PDIF signal from your coaxial S PDIF digital source such as a DAT MiniDisc player or external A D converter Use a quality digital cable rated at 75 Ohms 5 S PDIF Out This RCA connector sends a S PDIF signal to your coaxial S PDIF digital target device such as a DAT MiniDisc player or external D A converter This output is also used as a digital multi channel surround output Dolby DTS etc for DVD or Home Theater use Use a quality digital cable rated at 75 Ohms 6 USB Jack This stan
20. dard USB connector connects to the device end of a standard USB cable included 7 9V AC 1000 mA PSU Jack This jack connects to the included power supply which connects to common house current Use only a 2 5mm plug with a 9V AC 1000 mA power rating Using any other power supply could give undesirable results and or damage the Audiophile USB Guide to Getting Started Quickly Here is what is required to get your Audiophile USB up and running 1 Insert the included Drivers CD into your CD drive and locate the Audiophile USB folder Within that folder open the folder for the operating system that you are currently using and run the Audiophile USB Installer program NOTE Windows 98SE users will need the Microsoft Windows 98SE CD ROM 2 Plug the included power supply into your wall socket and the Audiophile USB s Power Jack Then attach the Audiophile USB to your computer with the included USB cable and power the unit On On Windows this will bring up the New Hardware Wizard after which installation will be complete 3 Configure your digital recording software to use the Audiophile USB as its active audio device see Using the Audiophile USB with your Software Application and also your software application s manual 4 Hook up your digital and analog audio gear see Audiophile USB Recording Tutorials Configure your Audiophile USB Control Panel software for proper monitoring and playback 5 Hardware In
21. ectX version 7 You must have DirectX version 8 1 in order to install the Audiophile USB The Audiophile USB installer will automatically check for the correct version of DirectX and install the latest DirectX update this update will be skipped if you already have DirectX version 8 1 or higher in your system 1 During this installation the Audiophile USB must be powered off Begin the installation process by inserting the Drivers CD ROM in your computer and double click on the Audiophile USB EXE icon in the Window that appears The installer will now check your computer for the correct version of DirectX If DirectX version 8 1 or higher is already installed proceed directly to step number 6 2 Assuming that the installer has not found Direct X 8 1 or higher it will now install DirectX version 8 1 Proceed with the DirectX installation by clicking Next 27 3 Click Yes to confirm that you wish to continue with the installation 4 Verify that you have read the license agreement and agree to the terms Click Yes to continue 5 Windows will need to restart your machine to complete the DirectX 8 1 installation Click OK to restart your system 6 This is the first setup window for installing the Audiophile USB drivers after the installer has confirmed that you have DirectX version 8 1 or higher installed on your system Make sure your Audiophile USB is powered off and that no other Windows programs are running then
22. er s USB port no tools or computer disassembly is required The Audiophile brings you true 24 bit 96kHz audio and the highest quality stereo and digital multi channel surround sound available today Even if you are experienced in digital recording please take the time to read this manual It will give you valuable information on installing your new interface and the supporting software plus help you to fully understand the function and usability of the Audiophile USB Once you re up and running you will quickly discover the power and brilliance both in sound and design of your new Audiophile USB Must meet minimum system requirements What s in the Box Your Audiophile USB box contains 1 One 1 Audiophile USB 2 One 1 Standard USB cable 3 One 1 9V AC 1 Amp Wall Wart power supply 4 Driver CD containing driver software and Audiophile USB Control Panel software for Windows and Macintosh OS 9 or X 5 M Audio Warranty Registration card 6 This Owner s Manual About the Audiophile USB The Audiophile USB gives you two analog line inputs and two analog line outputs plus coaxial S PDIF digital inputs and outputs for a total of 4 ins 4 outs of high quality audio I O All audio channels support 24 bit data width and any sampling rate from 8kHz to 96kHz The Audiophile USB is compatible with all major software programs running on PC and Macintosh computers The coaxial digital outputs are multi channel surround sound
23. er Latency try the very low setting first as shown in the previous screenshot and if your system stutters or performance falters try the next higher setting until the system performance stabilizes Once you are satisfied with any of the control panel settings click OK to close the Audiophile USB Control Panel Version Numbers The lower left corner the Audiophile USB Control Panel page displays the ASIO Driver Version USB Driver Version and the Firmware Version numbers currently in use This is useful when checking for driver updates on the M Audio website or in the event that you need to call tech support and give them your system information 12 Windows Sound System and the Audiophile USB Windows may be set up to use the Audiophile as its default audio device allowing system sounds to be played through the Audiophile This also enables you to use the Audiophile with the sound applets included with Windows To set this up go to Control Panel Sounds and Audio Devices or Multimedia in Windows 98 In the Audio Properties page set the Playback and Recording devices to the Audiophile USB input and output devices of your choice Windows may also use the Audiophile USB as its default MIDI device This allows the Audiophile USB to be used with the MIDI applications included with Windows To set this up go to Control Panel Sounds and Audio Devices Audio Or go to Control Panel Multimedia MIDI in Windows 98 Set the
24. gital Output Sample Rate 8kHz to 96kHz Data format S PDIF not AES EBU Connector Type Gold plated RCA and 1 4 female MIDI I O Configuration 1 in 1 out 16 MIDI channels in amp out Connector Type Standard MIDI 5 pin DIN 22 Appendix B Driver Software Install Step by Step Windows XP 1 During this installation the Audiophile USB must be powered off Begin the installation process by inserting the Drivers CD ROM in your computer 2 A Setup window will appear Click Next to continue 3 A Software Installation window will come up regarding Windows Logo testing As this is a relatively new product it has not gone through Windows Logo testing or certification yet Rest assured our USB drivers are of the highest quality and will not cause problems in your system Click Continue Anyway 4 A second Software Installation window will appear again with a similar alert Click Continue Anyway 23 5 A third Software Installation window will appear Click Continue Anyway 6 An M Audio USB Audiophile Setup window will appear next Make sure both the Enable Digital CD and Enable DMA Transfer Mode boxes are checked then click Next 7 Another M Audio USB Audiophile Setup window will appear next Click Next to successfully install the USB Audiophile 8 Windows will prompt you to restart the computer Make sure that Yes restart my computer now is checked and the
25. h A weighted All data paths support up to 24 bit 96kHz performance Windows 98Se Me 2000 XP drivers included supporting MME ASIO and WDM Me or greater Mac OS drivers with ASIO support also included Minimum System Requirements Windows 98Se 2000 Me or XP Mac OS 9 x or X Pentium II 266MHz for 96kHz operation Pentium 200 MMX for 48kHz or less 128 MB of RAM for 96kHz operation 64MB RAM for 48kHz or less Mac G3 with 64 MB of RAM 128 recommended with native USB OMS required for MIDI support under Mac OS 9 x 3 Front Panel Features 1 Headphone Out This is a stereo headphone output on a 1 4 TRS jack Connect only a stereo plug to this jack 2 Headphone Level This knob controls the level of the stereo output signal sent to the headphone jack 3 Output Level This knob controls the level of the stereo output signal sent to the RCA analog output jacks 4 MIDI In This 5 pin DIN accepts MIDI data from any external MIDI device via a standard MIDI cable supporting up to 16 channels of MIDI data on a single cable 5 MIDI Out This 5 pin DIN outputs MIDI data to any external MIDI device via a standard MIDI cable supporting up to 16 channels of MIDI data on a single cable 6 Power Indicator LED When power is supplied to the Audiophile this LED will light and remain lit 7 Power Switch On Off Pressing this switch and locking to the in position will apply power to the Audiophile USB provide
26. ifically M Audio makes no warranty that the product is fit for any particular purpose This warranty shall be construed interpreted and governed by the laws of the state of California If any provision of this warranty is found void invalid or unenforceable it will not affect the validity of the balance of the warranty which shall remain valid and enforceable according to its terms In the event any remedy hereunder is determined to have failed of its essential purpose all limitations of liability and exclusion of damages set forth herein shall remain in full force and effect 35
27. ill hear audio from the Audiophile but it will be running at an odd sample rate and sound like it is playing at the wrong speed DD DTS Pass Thru Just below the Sample Depth column you will see a checkbox labeled DD DTS Pass Thru If you are using a Software DVD player and wish to send encoded multi channel audio such as Dolby Digital or DTS to the Audiophile USB s S PDIF output port then check this box If you are only sending stereo audio standard PCM not encoded surround to the S PDIF output port during normal operation then leave this box unchecked If you have this box checked you can still send stereo digital audio to the S PDIF port without any problems However you will notice that when the DD DTS Pass Thru box is checked ONLY the S PDIF port is active in the Active Ports column Unchecking the DD DTS Pass Thru box will restore the port selection to the previous configuration Latency Driver Latency can be selected from a range of values shown in a drop down list located just below the Maximum Sample Rate The default setting when the Audiophile is first installed is Very High Because slower computer systems require larger sample buffers to avoid dropouts in the audio stream a higher latency value is often necessary How low you will able to set the Latency will depend on several factors such as your system s performance and the performance of the music program itself To test your system for low
28. n click Finish to restart 24 9 When you are completely restarted and at the desktop power up the USB Audiophile 10 The New Hardware Wizard will appear Please select Install the software automatically Recommended then click Next 11 A Hardware Installation window will come up Click Continue Anyway 12 A Completing the Found New Hardware Wizard window will appear next Click Finish to complete this portion of the installation 25 13 Another Windows Logo testing window will come up Once again click Continue Anyway 14 The New Hardware Wizard will appear again Select Install the software automatically Recommended by clicking on the radio button and then clicking Next 15 Another Hardware Installation window will appear regarding Logo Testing Click Continue Anyway 16 The final Completing the Found New Hardware Wizard window will appear Click Finish to complete the installation of your Audiophile USB 26 17 Open the Windows Control Panel and click on the Audiophile USB Control Panel Select Place Audiophile Icon in the task bar The Audiophile USB will have a small black M in the system tray for easy access to the control panel Windows 2000 NOTE Please make sure the Service Pack 3 is installed To get this update please visit the download section of Microsoft at www microsoft com Windows 2000 comes installed with Dir
29. not have microphone preamplifiers built into it Therefore directly connecting a 13 microphone is not recommended Instead pass the microphone signal through a microphone pre amp such as the M Audio TAMPA DMP3 or Audio Buddy and then connect the pre amp output to the input of the Audiophile USB Some additional cable and or cable adaptors may also be needed to ensure proper connectivity The Audiophile USB also has digital inputs and outputs in S PDIF format These are available on RCA connectors as stereo pairs These jacks receive or transmit a digital audio stream that is independent of the analog audio streams However because of the bandwidth limits of USB there can be a tradeoff between the number of inputs and outputs that are active and the sampling rate and bit depth of the audio being processed Also you should ONLY activate the S PDIF Input if you are connecting an active digital audio device to this input This is detailed in the previous section The Audiophile USB Control Panel Also detailed in the previous section is the use of the S PDIF Output for sending encoded surround sound signals Checking the DD DTS Pass Thru box in the Audiophile USB Control Panel will allow you send Dolby Digital Dolby Surround DTS or any encoded surround sound signal to the S PDIF Output of the Audiophile USB You can connect this output to a home theater system or any device that will decode this signal Using most DVD pl
30. on To configure your Audiophile USB MIDI in OMS go to the Control Panel or Chooser under the Apple Menu and make sure AppleTalk is turned off 7 this is recommended although OMS will sense that it is on and prompt you to turn it off If you are configuring OMS for the first time follow these instructions to configure OMS 1 In the Opcode folder which you will find on your hard drive locate the OMS Applications folder then OMS Setup Double click on OMS Setup 2 OMS will inform you that it has not yet been configured Click OK 3 The Create a New Studio Setup dialog box now appears Click OK 4 The OMS Driver Search dialog asks you to choose the port on which you ve attached the Audiophile USB MIDI either Modem or Printer DO NOT choose a port just click Search OMS begins Searching 5 OMS Driver Setup shows the Audiophile USB MIDI in a list when OMS successfully finds the driver Click OK OMS will now define shows Identifying the Audiophile USB output port The OMS MIDI Device Setup dialog box will appear showing the Audiophile s output port with a check box to the left of the port indicating that the port is enabled Now click on OK 6 Next the My Studio Setup appears with a file save dialog box over it You will now need to save your new Studio Setup before you can assign an instrument to the Audiophile s MIDI output and input Assign your instrument and you
31. ou will see in the lower left hand corner a checkbox that states Place Audiophile icon in the task bar You may create a shortcut on your Windows taskbar by clicking on this checkbox Upon closing the control panel the M Audio logo will appear in your taskbar Double clicking this icon will then open the Audiophile USB Control Panel Unchecking the control panel checkbox will remove the M Audio logo from the taskbar upon closing the control panel Note that the M Audio logo will only appear on the taskbar when the Audiophile is attached and powered On 9 On Macintosh During the driver installation a dialog box will ask you if you wish to place a shortcut to the control panel on your desktop Clicking this checkbox will upon completion of the driver software installation place a shortcut to the Audiophile USB Control Panel on your computer s desktop The control panel program itself will install to your system s hard drive In OS 9 the Audiophile USB Control Panel will be placed in the Control Panel folder which allows it to be accessed from the Apple Control Panel drop down list In OS X the control panel is installed into the System Preferences folder If you choose not to place a shortcut icon on your desktop during the installation process you may create an alias by highlighting the Audiophile USB Control Panel on the hard drive and pressing the Command Key M The alias may then be dragged to the desktop The control panel
32. r Audiophile USB is powered off and that no other Windows programs are running then click Next to continue 32 7 An M Audio Setup window will appear next Make sure both Enable Digital CD and Enable DMA Transfer Mode boxes are checked then click Next 8 An M Audio Setup window will come up confirming a successful setup Click Next to successfully install the USB Audiophile 9 Windows will prompt you to restart the computer Make sure that Yes restart my computer now is checked and then click Finish to restart 33 10 When you are completely restarted and at the desktop power up the USB Audiophile 11 Open the Windows Control Panel and click on the Audiophile USB Control Panel Select Place Audiophile Icon in the task bar The Audiophile USB will have a small black M in the system tray for easy access to the control panel 34 Limited One Year Warranty M Audio warrants that this product is free of defects in materials and workmanship under normal use for a period of one year so long as the product is owned by the original purchaser the original purchaser has proof of purchase from an authorized M Audio dealer and the purchaser has registered his her ownership of the product by sending in the completed warranty card This warranty explicitly excludes power supplies and included cables which may become defective as a result of normal wear and tear In the event that M Audio recei
33. sic program s audio setup page you will find a button that allows you to launch the ASIO device s control panel Clicking this button will now launch the Audiophile USB Control Panel allowing you to view the Audiophile USB audio settings 16 Audiophile USB MIDI Setup The Audiophile s MIDI input and output ports may be connected to external MIDI devices The following diagram shows connection to a MIDI keyboard instrument which is also being used as a sound module The MIDI output of the Audiophile USB may be used with just a sound module while the MIDI input may alternately be used to receive MIDI time code for synchronization purposes 1 Connect the MIDI out port of your controller keyboard to the Audiophile s MIDI In port using a standard MIDI cable 2 Connect the Audiophile s MIDI Out port to the MIDI in of your keyboard instrument or a sound module also using a standard MIDI cable 3 Connect the audio outputs of the keyboard to either a mixer sound system or the audio inputs of the Audiophile USB The Audiophile USB MIDI drivers once enabled in your software s MIDI Setup will appear as a MIDI source and a MIDI port within that program s track configuration windows The MIDI input driver is named In Audiophile USB and the MIDI output driver is named Out Audiophile USB Some software applications allow you to redefine rename these devices per supplied or manually entered instrument definitions Audio
34. stallation Find a convenient spot near your computer for the Audiophile USB With the Audiophile s power switched Off plug the included power supply into your wall socket and plug its 2 5mm plug into the Audiophile s 9V AC 1000 mA Power Jack Then simply connect the USB cable to your computer and to the Audiophile USB Please follow the Driver and Software installation carefully Apply power to the Audiophile USB switching the unit On ONLY when prompted Audiophile USB Driver amp Software Installation The Audiophile USB system includes a Software Drivers CD for Windows and Macintosh containing all Windows and Macintosh drivers including ASIO drivers and Audiophile USB Control Panel software To install on your system please follow these steps Windows Installation An Installer program is provided for Windows operating systems The Audiophile USB Installer greatly simplifies the work that the Windows New Hardware Wizard has to do and helps to ensure a trouble free and simplified installation You may also notice that a Windows Driver Signing dialog box will pop up a few times during the installation and you will be asked to press Continue Anyway This dialog box indicates that this is a relatively new product While we are going through the driver certification procedure with Microsoft we assure you that your Audiophile USB drivers are of the highest quality and will cause no problems in yo
35. the Device Manager page of the System Properties dialog box The Device Manager page can be opened by right clicking on My Computer either from the Start menu or your desktop depending on your operating system and selecting Properties from the list Select Hardware then Device Manager With the Device Manager displayed click on the next to Sound video and game controllers to open a list of devices the Audiophile USB being a device of that nature You will also see an entry for the Audiophile USB under Universal serial bus controllers Below is an example view of the Device Manager This example shows the M Audio Audiophile USB entries in the Windows Device Manager device list The Audiophile USB is properly installed with no conflicts If you do not see your M Audio Audiophile USB in your Device Manager in this fashion please jump ahead to the Troubleshooting section of this manual Verifying Control Panel Installation PC Macintosh On the PC Once the Audiophile USB is properly installed an M Audio Audiophile USB icon will be displayed in your Windows Control Panel which can be accessed from the Start menu By double clicking on that icon you will launch the Audiophile USB Control Panel software Once the Audiophile USB Control Panel software has been opened you will see the various controls for enabling inputs and outputs and for setting other parameters With the control panel open y
36. udio s liability for any damages to the purchaser or any other person exceed the price paid for the product regardless of any form of the claim M Audio specifically disclaims all other warranties expressed or implied Specifically M Audio makes no warranty that the product is fit for any particular purpose This warranty shall be construed interpreted and governed by the laws of the state of California If any provision of this warranty is found void invalid or unenforceable it will not affect the validity of the balance of the warranty which shall remain valid and enforceable according to its terms In the event any remedy hereunder is determined to have failed of its essential purpose all limitations of liability and exclusion of damages set forth herein shall remain in full force and effect 21 Appendix A Technical Specifications Analog Audio Peak Signal Analog Input 2dBV Peak Signal Analog Output 2dBV Dynamic Range Inputs 109dB A weighted Dynamic Range Outputs 107dB A weighted THD at 0dBFS 92dB typical Frequency Response 22Hz 22kHz 0 4 0 4dB Maximum Converter Data Width 24 bits Input Impedance 10k ohms minimum Connector Type Gold plated RCA female back panel Digital Audio Digital Input Sample Rate 8kHz to 96kHz Maximum Word Width 24 bits Digital Input Format S PDIF coaxial 0 5 to 5V peak to peak Digital Output Format S PDIF coaxial 0 5V peak to peak Di
37. udio device driver setup page will allow you to select the USB Audiophile ASIO driver This selection is advised and described more fully later in this section Windows MME and WDM Audio Input Devices Within the setup page of your software application s the names of the Audiophile USB audio input devices will be M Audio USB Audiophile Line and M Audio USB Audiophile SPDIF The M Audio USB Audiophile Line device allows recording a stereo stream directly from the analog Left and Right Input pair while the M Audio USB Audiophile S PDIF device allows you to record a stereo stream directly from the S PDIF Input Note that the input devices are stereo Your application software may break these down further to left and right mono devices Therefore you may see them as Left M Audio USB Audiophile Line and Right M Audio USB Audiophile Line or Left M Audio USB Audiophile S PDIF and Right M Audio USB Audiophile S PDIF from within your recording software If your application allows for recording stereo tracks you will also be able to select Stereo M Audio USB Audiophile Line and Stereo M Audio USB Audiophile S PDIF Windows MME and WDM Audio Output Devices Within your software application s the names of the Audiophile USB audio output devices are M Audio USB Audiophile Line and M Audio USB Audiophile SPDIF Most application software will handle the outputs
38. ur system 1 Insert the Drivers CD into your CD ROM drive Locate and open the Audiophile USB folder Double click on the Audiophile USB Installer program in that folder 2 As the Installer loads the Audiophile USB drivers a Windows Driver Signing XP and 2000 Users only dialog box may pop up a few times during the installation Click Continue Anyway 3 When asked to switch On your Audiophile USB do so This will bring up the Windows New Hardware Wizard Click Next at each prompt and the Hardware Wizard should automatically recognize all of the Audiophile Drivers NOTE Windows 98SE users will need their Microsoft Windows 98SE CD ROM here 6 4 The Wizard reports that Windows has finished installing the software Click Finish Your Audiophile USB is ready for action After completion of the driver installation Windows may require you to restart Windows If it does request a restart remove the Drivers CD from the CD drive and respond by clicking Yes The system will restart and your Audiophile USB is ready for play Macintosh OS 9 Installation NOTE To use the Audiophile USB on Mac OS 9 you must also install Opcode s OMS This should be done BEFORE running the Audiophile USB s Installer program By installing OMS first the Installer program will then be able to place the OMS driver in the proper folder Then after running the Installer you will need to configure OMS See the section O
39. ves written notice of defects in materials or workmanship from such an original purchaser M Audio will either replace the product repair the product or refund the purchase price at its option In the event any repair is required shipment to and from M Audio and a nominal handling charge shall be borne by the purchaser In the event that repair is required a Return Authorization number must be obtained from M Audio After this number is obtained the unit should be shipped back to M Audio in a protective package with a description of the problem and the Return Authorization clearly written on the package In the event that M Audio determines that the product requires repair because of user misuse or regular wear it will assess a fair repair or replacement fee The customer will have the option to pay this fee and have the unit repaired and returned or not pay this fee and have the unit returned unrepaired The remedy for breach of this limited warranty shall not include any other damages M Audio will not be liable for consequential special indirect or similar damages or claims including loss of profit or any other commercial damage even if its agents have been advised of the possibility of such damages and in no event will M Audio s liability for any damages to the purchaser or any other person exceed the price paid for the product regardless of any form of the claim M Audio specifically disclaims all other warranties expressed or implied Spec
Download Pdf Manuals
Related Search