Magnadyne M10 Automobile Alarm User Manual
Contents
1. NOOR WDM Disabling the Remote Start System If Installed This feature allows your system s remote start unit to be temporarily disabled to prevent the vehicle from being remote started accidentally This feature is useful if the vehicle is being serviced or stored in an enclosed area To disable the remote start move the optional remote start toggle switch to the OFF position 1 15 02 Rev A M10UM 42. bypassed however the remote panic feature and remote door locks will remain operational to use the valet mode the system must first be disarmed either by using your remote transmitter or by operating the manual override sequence Remote Door Lock Remote Door Unlock ra 200 hr e00 Z A A D SA le Enter Valet Mode 1 From the disarmed condition turn the ignition to ON position 2 Push and hold valet switch for 2 seconds until the LED turns on The LED will remain on as long as the system is in valet mode Exit Valet Mode 1 Return to normal operation turn ignition ON 2 Push and hold valet switch for 2 seconds The LED will turn off to indicate the system is exiting the valet mode Car Locator Press the q button to activate the car locator function the siren will chirp 6 times The parking light will flash 12 times for you to easily locate your car Panic Function Panic Function See Alarm Feature Programming Part 1 7 The transmitter can be used as a remote panic switch to manually trigger the alarm in case of emergency 1 Press and hold the 4 button for 3 seconds The alarm will immediately sound 2 During panic mode the normal function of this transmitter button will be suspended The and sf buttons can be used to lock and unlock the doors if the option is installed however on the gf button is pressed the vehicle s starter disable device where installed will be enabl
3. for 1 second 2 The parking light will activate to indicate the remote start received the signal 3 The engine will start approximately 5 seconds 4 Once the engine is running after couple seconds the parking light will turn on again and climate controls will activate and adjust the vehicle s interior temperature to your preset setting 5 The vehicle will run for 5 to 30 minute cycle and automatically shut down 10 a M10UM 2 20 02 12 26 PM Page 11 G Remote Start the Vehicle Melody sound from 2 way LCD Transmitter when remote start is activated Note The remote start unit will not start the vehicle if any one of the following conditions exists 1 The hood is opened 2 The brake pedal is pressed 3 Move the optional remote start enable toggle switch to OFF position If installed 4 The gear selector is in any gear other than PARK or NEUTRAL To Turn Off the Remote Start When the engine is running by remote start if you want to stop it 1 Press 3 button on the transmitter 2 Move the optional remote start enable toggle switch to the OFF position If installed 3 Press the brake pedal The vehicle will shut down and turn off the parking light to indicate engine stopped To Operate the Vehicle While Running on the Remote Start To operate the vehicle while running on the remote start 1 Insert the ignition key and turn it to ON not the start position 2 Press the brake pedal Note If the brak
4. the ignition switch or arm the alarm will turn off the dome light Ignition Control Door Locks Ignition Control Door Locks See Alarm Feature Programming Part 2 2 If the vehicles door locks have been interfaced to the security system the system will automatically lock the vehicle s doors when the ignition is turned ON and or unlock the vehicle s doors when the ignition is turned OFF Trunk Release Timer Control Output Trunk Release Factory Default Setting Timer Control Output See Alarm Feature Programming Part 2 6 Press and hold the s button on the transmitter for two seconds to remote control the trunk release or other electric devices 4 o M10UM 2 20 02 12 26 PM Page 10 G System s Status Check When you want to check the system s present status thru the LCD screen press the button on the Two Way LCD Screen Transmitter With one melody sound the system s status will be shown on the LCD screen Note Press SET for 2 seconds with 2 beeps confirmation to clear the trigger icons of LCD screen Driver Paging Optional If you installed the optional Paging Knock Sensor it is useful in the event that someone wants to page the driver of the parked vehicle If someone tries to page you by tapping the paging knock sensor which is usually mounted on the bottom part of front window the paging melody sound continues sounding from your Remote LCD Transmitter and call indication flashes on the LCD
5. 4 times parking light flash 3 times Pathway Illumination See Alarm Feature Programming Part 2 4 This feature turns the parking light ON for 30 seconds upon a unlock signal and for 10 seconds upon the lock signal Two Steps Door Unlock See Start Feature Programming Stage 1 This feature will independently unlock the driver s door only when disarming the security system Pushing the gf button a second time within 3 seconds will unlock the entire vehicle Automatic Re Arm See Alarm Feature Programming Part 1 3 If this feature is selected the security system will automatically re arm itself 60 seconds after disarming with remote transmitter Automatic rearm will cancel if any door is opened before the 60 seconds timer has elapsed Disarming Without a Transmitter Override the Alarm The override function may be used if the remote transmitter is lost or inoperative 1 Enter the vehicle and turn the ignition switch to ON position Alarm will sound 2 Within 10 seconds push and release the valet switch The alarm will stop sounding and enter the disarm mode You can now start and operate the vehicle normally M10UM 2 20 02 12 26 PM Page 7 3 Valet Mode System in Disarmed or Valet Mode The valet switch allows you to temporarily bypass all alarm function eliminating the need to hand your transmitter to parking attendants or garage mechanics When the system is in valet mode all alarm function and remote start function are
6. M10UM 2 20 02 12 26 PM Page 1 3 arksman ser s Manual Model M10 For Technical Assistance 800 638 3600 For Fax on Demand Technical Assistance 800 994 9977 Must be a Registered Dealer to Use Fax on Demand System Copyright 2002 Magnadyne Corporation M10UM 2 20 02 12 26 PM Page 2 3 Congratulations on your purchase of a quality Marksman automotive security and remote start system The information enclosed will provide a ready reference of the operation and maintenance of your new Marksman security and remote start system Operation Regular Transmitter Operation Transmitter System Function Remark Button a Lock Doors and Arm System Lock Doors Arm System and Turn a 2 Seconds On Paging Sensor Chirp Confirmation B 4X Arm and Noiseless Mode Press within 3 Seconds Arm and Delete the Zone 1 Shock Sensor Arm and Delete the Zone 4 Optional Sensor Arm and Delete the Zone 1 Shock Sensor Delete the Zone 4 Optional Sensor Press Twice within 3 Seconds Press Third Time within 3 Seconds Press Fourth Time within 3 Seconds Unlock Doors and Disarm System my 2 Seconds Disarm and Channel 2 Trunk Timer Control Press and Hold for 2 Seconds ia Two Steps Door Unlock and Disarm System Press Twice within 3 Seconds 4X Silent Arming Disarming Ignition in OFF Position 4X 4X 4X 2 Seconds Hidden Alarm Function A
7. ctivate Car Jacking Ignition in ON Position and Press and Hold for 2 Seconds 4 Car Locator 4 3 Seconds Panic Function Press and Hold for 3 Seconds k 1 Second Activate Remote Start Press and Hold for 1 Second koJ System s Status Check For M10RF LCD Only m 2 Seconds Channel 2 Trunk Timer Control Press and Hold for 2 Seconds eo e Passive Arming By Pass While the System Disarmed Turn Off the Remote Start I Switching Code for 2nd Car Operation or For M10RF LCD Only 4 M10UM 2 20 02 12 26 PM Page 3 E Second Vehicle Transmitter Programming Random code transmitters does not have this feature Your 8 button remote transmitter can be utilized to control a second vehicle security system To program the remote control transmitter to a second vehicle follow the instructions for Transmitter programming All programming parameters be the same except for the following 1 Prior to pushing any button on the transmitter Press the select I button first 2 Once the If button is pressed the LED on the transmitter will illuminate for 3 5 seconds 3 While the LED is illuminated press any button on the remote control transmitter LED Display LED Function LED Function Off Disarmed 1 flashes pause Zone 1 Trigger on Board Shock Sensor Slow F
8. d trunk the security system LED will stop flashing It will begin flashing again one the vehicle s entrances are closed 3 After 30 second timer has elapsed the security system will automatically ARM The siren will chirp 1 time and the parking lights will flash 1 time Passive Arming with Passive Door Locking See Alarm Feature Programming Part 1 2 The vehicle doors will automatically lock after passive arming cycle has been completed Passive Arming By Pass While the system disarmed press the button twice the security will respond with 1 chirp and LED will turn ON The security system will remain in this temporally state for as long as you wish To exit passive by pass press the f or af button and the system will return to normal status Active Disarming Unlock and Disarm 1 Press mf button on the transmitter 2 The siren will chirp twice and parking light will flash twice to indicating that the security system is now disarmed The vehicle doors will unlock and dome light will turn on for 30 seconds upon disarming when interfaced with the security system System Disarm Doors Trigger Trunk Hood Trigger Shock Sensor Trigger Lat MOGO 0O jaa e00 2a 2 08 G o_o M10UM 2 20 02 12 26 PM Page 6 3 Active Disarming Unlock and Disarm Optional Sensor Trigger Ignition Trigger tat CGE t e00 lao D ZH f Tamper Disarming If alarm triggered upon disarm the system siren chirp
9. e allowing the vehicle to start 3 To stop the alarm press and hold the or 4X or or wf button on the transmitter again for 3 seconds Also in any transmitter button other than the or 4X or or af button is pressed and released the panic mode will be turned off immediately 4 If the button is not pressed the alarm will automatically stop after 60 seconds M10UM 2 20 02 12 26 PM Page 8 3 Trigger the System When armed your vehicle is protected as follows 1 Light impacts will trigger the warn away signal A 3 long chirp from siren horn 2 Heavy impacts doors open hood open trunk open turn on the ignition key activate PIR sensor activate door window sensor will trigger the programmed sequence The starter disable relay if installed prevents the vehicle s starter from cranking The siren horn parking lights and dome light will turn on to alert an intrusion for 60 seconds It will stop automatically re set and re arm If one the sensors or detectors are still active the alarm system will sound a maximum of 3 times for 60 second cycles Doors Trigger Trunk Hood Trigger Shock Sensor Trigger Optional Sensor Trigger 1a 1200 e megg te megg 8 200 ARMED Ignition Trigger sa 2 00 ARMED se PE py fi Noise Abatement Circuit Your system has Noise Abatement Circuit It prevents annoying repetitive trigger sequences due to faulty door pin switches or envir
10. e pedal is pressed before the key is in the ON position the engine will shut down Temporary Stop Feature This feature allows the vehicle to remain funning after the key has been removed from the ignition This feature is useful for occasions when you wish to exit and lock the vehicle for short periods of time but would like to leave the motor running and the climate control on 1 Before turning off the engine press the af button on the transmitter and the LED indicator will flash 3 times to confirm enter 2 Turn the ignition key to OFF position The engine will stay running 3 The engine will run until the pre programmed time elapsed or shut down input is received Timer Tem perature Start This unit can be programmed to start and run the engine every 3 or 24 hours the engine will run for the programmed run time and then shut down IMPORTANT Timer Start should be used only in open area never start and run the vehicle in on enclosed space as a garage or carport 3 hours timer start with temperature control OFF This feature is design for an extreme cold climate usage The system will auto start the vehicle every 3 hours to prevent engine freezing and hard to start A MAXIMUM OF SIX CYCLES CAN OCCUR 3 hours timer start with temperature control If you installed the optional Temperature Sensor and programmed the temperature ON to operate The system can be programmed to automatically start the vehicle engine whenever the tem
11. er when the door is opened and closed while the ignition is ON Trigger the Car Jack Mode 3 timer circuits will function as follows First Timer A 50 seconds after the system has been triggered the siren will start chirping for 15 seconds B During this 15 seconds period of chirping you can push the valet switch once to turn off the car jacking feature C If not it will enter second timer car jacking mode Second Timer 65 seconds after the system has been triggered The siren starts alarming and the parking light starts flashing Third Timer 90 seconds after the system has been triggered A The siren still alarming and the parking light flashing and B The starter disable will activate to prevent the vehicle from being re started if turned Off C It will remain active until the vehicle s battery power exhausted Override the System to Turn Off Car Jacking Turn the ignition switch form OFF to ON and within 10 seconds push valet switch the siren will stop and the system disarmed Note If you use password pin code to double protect the vehicle security you will need to use it to completely disarm the system Dome Light Convenience Delay and Supervision The alarm with a unique feature which will turn on your vehicle dome light as following 1 Upon disarming the interior lights will remain on for 30 seconds 2 If the vehicle is intruded the interior light will flash for the same duration as the siren Note Turn on
12. lash Armed 2 flashes pause Zone 2 Trigger on Trunk Hood Fast Flash Passive Arming 3 flashes pause Zone 3 Trigger on Door Switch On Solid Valet Mode 4 flashes pause Zone 4 Trigger on Optional Sensor 6 flashes pause Zone 6 Trigger on Ignition Switch Chirp Function Parking Lights Function 1 Chirp Arm 1 Flash Arm 2 Chirps Disarmed 2 Flashes Disarmed 3 Chirps Defective Reminder 3 Flashes Disarm Triggered 4 Chirps Disarm Triggered 12 Flashes Car Locator 6 Chirps Car Locator Constant On Under Remote Start Alarm Operating Condition Siren Horn Parking Light LED Doors Starter Dome Light 1 Arming 1 or 3 Chirps 1 Flash Slow Flash Locking Disable 2 Disarming 2 or 4 Chirps 2 or 3 Flashes Fast Flash Unlocking Turns on for 30 Seconds 3 Trigger Alarming Flashes Slow Flash Disable Flashes 4 Panic Alarming Flashes Flashes 5 Car Jacking Alarming Flashes Disable Flashes 6 Car Locator 6 Chirps 12 Flashes M10UM 2 20 02 12 26 PM Page 4 E Active Arming Lock and Arm 1 Press a button on the transmitter 2 The siren will chirp once and parking light will flash once indicating that the system is now armed The vehicle doors will lock upon arming when interfaced with the security system System Arm Door Ajar Trunk Hood Ajar Le 9 00 ha magg an ie GG ARMED lt a Aw 0 Defective Sensor Reminder If the siren sounds 3 chirps then you have left a door trunk o
13. onmental condition such as thunder jackhammers airport noise etc Here s how Noise Abatement Circuit works The alarm triggers five times Each time the same sensor or switch is triggering the alarm Noise Abatement Circuit will interpret this pattern of triggers as false alarm After the fifth trigger Noise Abatement Circuit Ignores or bypasses that sensor or switch until the other sensor or switch is triggered Doors hood trunk are covered by Noise Abatement Circuit differently If the alarm is triggered by an open door for 3 full cycles one minute of each cycle the doors will be bypassed until the trigger ceases Anti Car Jacking Warning If you don t need the car jacking function in this alarm system be sure to set car jacking feature OFF This system is default setting all car jacking OFF See Alarm Feature Programming Part 1 5 Active Car Jack 1 Press and hold 4X button on the transmitter for 2 seconds while the vehicle s ignition is ON The parking light will turn on for 1 5 seconds to indicate this enter 2 Once the system is armed if you are forced from the vehicle the system will trigger when the door is opened and closed while the ignition is ON 4 M10UM 2 20 02 12 26 PM Page 9 3 Anti Car Jacking Passive Car Jack It operate as below 1 Turn the ignition switch to ON the system will arm 2 Once the system is armed if you are forced from the vehicle the system will trigg
14. perature inside the vehicle reaches or drops below the preprogrammed temperature level The system will monitor the air temperature every 3 hours and will only start the engine during extreme cold temperatures There are three temperature level to choose from This feature is programmed OFF from the factory and must be programmed ON to operate See Start Feature Programming Stage 1 7 a M10UM 2 20 02 12 26 PM Page 12 G Timer Temperature Start 24 hours timer start This feature is design for a battery charge usage When the car owner has a long vacation he can use this feature to auto start the vehicle and charge the battery every day to prevent a low battery Enter 1 Press the 3 button to remote start the vehicle As soon as the vehicle is running and the parking light have turned on or flashing 2 Immediately depress the lt button once within 2 seconds 3a 3 hour auto start Rapidly depress the af button once The parking light will slash 3 times The siren or horn chips 3 times The vehicle is now programmed to start every 3 hours A 2 00 3b 24 hours auto start Rapidly press and hold the 3 button once The parking lights will flash 12 times The siren or horn chirps 12 times Pat The vehicle is now programmed to start ever 24 hours G0 x f 4 Press the brake pedal to stop the vehicle running i Exit the Timer Start Timer start can be exited manually as follows 1 Make sure
15. r hood lid ajar See feature l 4 programming Silent Arming Disarming Press the X button on the transmitter will arm or disarm your security system No chirp sound will be heard arm disarm confirmation will be through the vehicle s parking lights only Noiseless Mode Press the button once The siren chirps once The system is armed Press the X button within 3 seconds The siren chirps once again the system is now in Noiseless Mode On this mode trigger the zone 1 shock sensor or zone 4 optional sensor the trigger timer will reduced from 60 seconds to 15 seconds The noiseless feature is programmed to activate for one arming cycle only The security system will return to normal operation during the next arming cycle Shock Sensor Optional Sensor By Pass 1 Press the fi button once The siren chirps once The system is armed 2 Press the button a second time within 3 seconds The siren chirps once the Zone 1 Shock Sensor is now bypassed 3 Press the button a third time within 3 seconds The siren chirps twice the Zone 4 Optional Sensor connected to 4 pin plug is now bypassed 4 Press the button a fourth time within 3 seconds The siren chirps three times the Zone 1 Shock Sensor and the Zone 4 Optional Sensor connected to 4 pin plug are now bypassed Note The sensor bypass feature is programmed to activate for one arming cycle only The security system will return to normal operation du
16. ring the next arming cycle Hidden Alarm Function Press the X button first then press the X button a AM e IE within 3 seconds the security system will arm and with Hidden Alarm Function The siren horn will be silenced and ARMED parking light dome light will not flash even if the sensors are AY triggered in the armed status CA Y NA s 4 M10UM 2 20 02 12 26 PM Page 5 3 Active Arming Lock and Arm Arming While Driving See Alarm Feature Programming Part 1 6 Your system can be armed while driving the vehicle Simply press f button for 2 seconds while the vehicle is running or the ignition is on the system will chirp once and then once more to indicate the ignition is on The system will not respond to any input except the door trigger and the starter kill relay and ignition disable relay will not be activated The system will disarm automatically when the ignition is turned off The siren will chirp twice and the LED will stop flashing Passive Arming Active arming disarming is controlling your security system via the remote transmitter This security system is equipped with an optional Passive Arming feature which allows the security system to arm 30 seconds after the last door is closed Operation is as follows 1 Turn the ignition to the OFF position and exit the vehicle 2 After all entrances are closed the security system LED will flash fast for 30 seconds If you reopen any door hoo
17. screen 1 The function works only in arming status as well as press f for 2 seconds It responds with chirps of the vehicle s siren melody sound and call indication flashes on the LCD screen to confirm the function is on 2 When tapping the paging knock sensor one chirp sound shall be emitted from the vehicle 3 Any time while the system arms again the function will no longer be available Power Memory This security system is equipped with circuitry that will allows the unit to remember its alarm state if the power is lost and then reconnected Remote Start Operation WARNINGS As with any product that performs automatic functions there are certain safety precautions that you must practice and be aware of 1 Keep the transmitter out of children s reach Do not leave anyone in the vehicle while running on remote control Alert servicing personnel that the vehicle can be started automatically Do not start the vehicle by remote while it s in an enclosed area or garage Always apply the parking brake and lock the vehicle as you exit the vehicle Should the unit malfunction disconnect the fuse until the problem is corrected The use and operation of this system is the sole responsibility of the operator Some areas may have local ordinances that prohibit leaving a vehicle running on public streets OANDoOF WP To Remote Start Operation When you want to start your vehicle 1 Press 3 button on the transmitter
18. the remote start system is not operating the engine 2 turn the ignition ON the LED and parking light will flash 4 times The horn chirps 4 times or 1 Press the 2 button to remote start the vehicle As soon as the vehicle is running and the parking light have turned on or flashing 2 Immediately depress the lt button then press and hold the afe button for 2 seconds The parking lights will flash 4 times The siren or horn chirps 4 times The vehicle is no longer programmed to start automatically Temperature Check Optional If you installed the optional temperature sensor you can monitor thru the LCD screen the present indoor temperature of the passenger compartment before cooling or heating your vehicle Press the lt and m button at the same time on the Two Way LCD Screen Transmitter the in door temperature and system s status will be shown on the LCD screen Shut Down Input for Remote Starter If any of the following conditions exist while the system is operating the engine will not start or will shut down immediately The hood is opened The brake pedal is pressed Engine is over revved Tachometer Checking Type Only The pre programmed run time is 5 10 20 30 minutes has elapsed Transmitter button 3 is pressed Move the optional remote star enable toggle switch to OFF position if installed The vehicle refused to start running after 3 unsuccessful attempts
Download Pdf Manuals
Related Search