Lightolier MDC20 CD Player User Manual
Contents
1. front of the cabinet The cabinet features a double hinged lockable latching cover The cover is made from heavy gauge steel which prevents tampering of the devices The MDC20 Cabinet features air vents to maintain proper air flow through the dimmers The cabinet shall insure satisfactory operation of the equipment within an ambient temperature range of 0 to 40 C No cooling fans are used For applications that require rough in prior to the dimmers being installed order the MultiSet Pro Cabinet Enclosure MDC20ENC and Cabinet Interior MDC20INT See 87 0573 MDC20 Product Specification Sheet Wiring Entrance into the line voltage wiring section is through the double hinged front cover of the cabinet Provide a separate neutral connec tion for all loads no common neutrals If normal power is lost the dimmers will retain their presets and will return to their last state when power is restored Note Each dimmer is fed from an individual circuit breaker See Typical Wiring Diagram on page 7 Read Before Beginning Installation 1 All MultiSet Pro devices require a neutral connection no common neutrals Each circuit feeding dimmers and dimmed loads require a separate neutral Shared neutrals will result in undesirable flashing of controlled loads 2 Use VA dimmers to control incandescent low voltage with magnetic transformers neon cold cathode or general inductive loads When calculating a magnetic low voltage load2. is on quickly tap OFF and then ON The lights adjust to the preset level e To bypass the fade rate and turn the lights to full ON or OFF double tap the dimmer for ON or OFF e Ifthe Master is in the OFF scene the Master ON button illuminates when any dimmer is turned on To change the preset level of the current scene Figure 7 e Press and hold the rocker until lights reach the desired level then release e Press the small set button next to the switch to save the preset in memory LEDs on the MultiSet Pro Dimmer Switch indicate status S 1 Red LED is on when Dimmer Switch is off to locate Dimmer Switch when room is dark Red LED Green LED 2 As many as 3 green LEDs may be illuminated at any given time The bright green LED indicates the current level of the dimmer The medium green LED indicates the preset level G Set of the current scene The dim green LED indicates the preset level of the ON scene Button MULTISET PRO UNIVERSAL ELECTRONIC SwitcH Non Dim The MultiSet Pro Universal Electronic Switch can be programmed as a four or five scene non dim switch When programmed as a five scene device it is not suitable for 3 way applications The default mode of the switch is as a normal 4 scene non dim device The AV 5 scene mode allows the non dim switch to remain off when the master ON button is pressed To change the mode of the switch 1 Tap OFF on the Master to place the switch in the OF
3. 5 MDC20 MDC20 MDC20 PIII MHPWDC20 Pui UII B B BIB g Ay B 8 8 8 8 8 8 OO 6 0 pl El al Tg OyG G 0 O B 0 0 m li m B B BIB b B BIBIB 1B B B B camm ENANAR ooo omae o o o 0 HAVE glojoja olo o o Purple Wire Purple Wire Up to 30 MultiSet Pro Devices may be controlled as one system MULTISET PRo PRE WIRED DIMMING CABINET MDC20 poet and Operation Cabinet Specifications Input Voltage 108 132VAC 60Hz 3Hz Operating Temperature 0 40 Celsius Weight 80 lbs empty 88 Ibs with 20 1000W dimmers Dimensions 45 5 H x 20 1 W x 5 5 D Materials White 16 Gauge Steel C US Enclosure Double hinged cover lockable latching cover LISTED 20 1 i co a ao hb a a y aD i 18 0 fee 2 f 1 5 oO 45 5 Note Cabinet cover has a swinging radius of 21 a a SS lt a AD ao cB Bb 3 YEAR LIMITED WARRANTY Lightolier Controls warrants that this product will be free from defects in workmanship or materials This warranty is void on any electronic controls which have been overloaded abused improperly installed or altered in any manner Lightolier Controls sole obligation will be at its option to
4. F Raiseil ower 4 i e Press LOWER button to lower lighting level ae Ellipse series Tap a scene button to access one of the preset light levels Receiver e Two quick taps of any button except RAISE or LOWER will fade lighting quickly ER MULTISET PRO PRE WIRED DIMMING CABINET MDC20 and Operation Setting the Button Brightness Ellipse Series The brightness level of each Ellipse Master Control Station button can be programmed to 100 factory default 75 50 or 25 To change the setting 1 Ona 5 Scene Master press and hold buttons B and D simultaneously for 3 seconds on an 8 Figure 13 Scene Master press buttons H and J On a 5 Scene Master buttons A thru D illuminate on an 8 Scene Master buttons G thru J illuminate The blinking LED displays the current 5 Scene 8 Scene LED F Master Master Brightness LED brightness setting The continuously illuminated LEDs display the available brightness set tings that can be selected A G 100 2 To change the brightness setting press the button illuminated at the desired brightness This button A H a will begin blinking D J 25 p To save the selected brightness and exit the mode press the ON button on a 5 Scene Master or the E button on an 8 Scene Master All buttons on that master will now have the new brightness setting Typical Wiring Diagram To Lighting L
5. F scene 2 Press and hold the SET button After 3 Seconds a green LED illuminates on the bargraph If the switch is currently in normal mode the bottom green LED illuminates If it is in AV mode the top LED illuminates 3 Tap the top of the rocker once to toggle the mode 4 Release the SET button Note In normal mode a soft start feature is utilized to extend bulb life In AV mode the soft start feature is not implemented Programming Scenes After you have completed installation of all the MultiSet Pro devices and have energized the system each scene can be programmed 1 Tap the preset button ON A L on the MultiSet Pro Master that you wish to program see Step 1 Figure 8 2 Adjust each MultiSet Pro Dimmer to the desired intensity and the MultiSet Pro Switches to either ON or OFF see above 3 Press the Set button on each device see Step 3 pg 7 after all devices have been adjusted Step 1 Figure 8 lt Preset Buttons ON A B C D Repeat Steps 1 3 until all scenes have been programmed Buttons E L E F G H lt Preset I J K l MULTISET PRo PRE WIRED DIMMING CABINET MDC20 pore and Operation Changing the Fade Rate MultiSet Pro Dimmers can be programmed for 12 different fade rates Dimmers Figure 9 can be programmed to have a different fade rate on each scen
6. MuttISET PRo PRE WIRED DIMMING CABINET MDC20 a E INSTALLATION AND LIGHTOLIER OPERATIONS MANUAL IMPORTANT RETAIN THESE INSTRUCTIONS FOR THE END USER DO NOT DISCARD MULTISET PRo PRE WIRED DIMMING CABINET MDC20 COMPATIBLE WITH MULTISET PRO HEATSINK DIMMER MODELS MHP5ES MHP8ES MPHSAVES MHP8AVES MHP600VA MHP1000VA MHP1500VA MHP2000VA MHP1000ND MHP2000ND MHP500QE MHP6OOHDF120 MHP1500HDF120 MHP600EB MHP1000EB MHP1500EB MHPWHIS WARNING Before installation disconnect power at circuit breakers or remove fuse to avoid electrical shock or damage to the unit It is recommended that an electrician perform this installation Made in U S A For technical sales assistance call 1 800 526 2731 www lolcontrols com P N 85 1530 MULTISET PRo PRE WIRED DIMMING CABINET MDC20 pore and Operation The MultiSet Pro is a revolutionary system of advanced digital wallbox dimmers for economical and flexible multi scene multi chan nel control MultiSet Pro provides flexible 13 scene preset dimming control for up to 30 devices as well as 12 adjustable fade rates up to one hour that are programmable by scene The MultiSet Pro Pre Wired Dimmer Cabinet MDC20 facilitates desig
7. a 25 transformer loss must be factored i e actual lamp wattage plus 25 equals total load 3 Use Quiet Electronic QE Dimmers to control only low voltage fixtures that have electronic solid state transformers and regular incandescent loads Not for use with Magnetic Low Voltage fixtures 4 Use HDF Direct Drive Dimmers to control fluorescent lighting loads at 120V with approved Lightolier Controls PowerSpec HDF Flectronic Ballasts only and Lightolier Controls Dimming Amplifiers 5 Use Electronic Ballast EB Direct Drive Dimmers to control Advance Mark 10 Dimmable Electronic Ballast 6 MultiSet Pro Dimmers or Switches may be fed individually or in groups regardless of phase 7 MultiSet Pro Masters draw approximately one watt and may be fed through any circuit Multiple masters may be interconnected The total number of dimmers and masters are not to exceed 30 An unlimited number of channel remotes MSCR may be used 8 HDF Dimmers can be connected to a Dimming Amplifier Please consult interface and amplifier instructions for wiring Non dim switches can be connected to MultiSet Pro relay modules for 277V loads 9 Line voltage must not be supplied by a GFI breaker CAUTION Be sure that power to the load being controlled is disconnected by removing fuse or turning circuit breaker off Installing MultiSet Pro dimmers or Masters with power on may expose you to dangerous voltage and damage the device A qualified electri
8. cian should perform this installation EPA MUITISET PRO PRE WIRED DIMMING CABINET MDC20 Cabinet Installation 1 Surface or recess mount on wall using appropriate wall anchors Use wall anchors capable of support ing up to 80 90 pounds Figure 1 Note All wiring should be in accordance with local regulations and the National Electrical Code All wiring shall enter and exit the cabinet via the provided knock outs at the top or bottom of the cabinet 2 Terminate 120VAC lines and neutrals to terminal blocks Do not use common neutrals 3 Connect lighting loads to the load terminal block Be sure to match proper load with the correct device refer to device location sticker on front of cabinet 4 Connect ground to dimming cabinet 5 Connect network purple wire to additional cabi nets when necessary Each Cabinet Cover has a swinging radius of 21 Features Figure 2 Dimmer Terminal Blocks 1 Anchor mounts Figure 1 Detail C see descriptions below 2 Terminal blocks Figure 2 fe 3 Ground terminal strip 4 Dimmer mounting panel Enclosure 5 Cabinet latch ye i separately for 6 Order part number MDC20ENC Door and door frame P Note No common neutrals Interior Terminal Blocks Mounting Back Plane Dimmer s Mounting Panel Door and Door Frame Can be ordered separately and installs into MDC20ENC Order part number MDC20INT Requires pa
9. e The fade rate choices are 1 5 seconds 1 minute 2 min F 3 seconds 2 minutes ens nz i 4 5 seconds 5 minutes j m pal 30 min 7 5 seconds 15 minutes 7 5 sec p oz Ly 15 seconds 30 minutes 4 5 sec al 15 min 30 seconds 60 minutes 3 sec gt sek lt Smin Global Fade Rate One fade rate for all scenes 1 5 sec ais PE Each dimmer s fade rate affects all scenes Examples Dimmer 1 fade rate set 7 5 sec a f Green dimmer 2 set to 15 sec and dimmer 3 set to 3 sec When any scene is selected dim LED Lights mers 1 2 and 3 will respond with 7 5 15 and 3 seconds respectively for ON OFF A B C D E F G H I J K and L To change the Global Fade Rate that affects all scenes Figure 10 1 Tap the OFF button on the Master 2 Press and hold the SET button After 3 seconds either a single green LED or a Step 1 pair of green LEDs indicates the current global fade rate The bottom LED indi Press and hold Set cates the 1 5 second fade rate the next LED up is 3 seconds while the top LED is button for 3 seconds 2 minutes If the bottom two LEDs are on it indicates the 5 minutes fade rate if the next two LEDs up are lit it indicates 15 minutes while the top two LEDs ra Step2 indicate the 60 minute fade rate Tap top of dimmer paddle to increment fade rate Note When the two LEDs are on they will not be at the same intensi
10. n and installation by combining dimmers and controls into a com mon enclosure Each cabinet is shipped assembled pre wired and tested with its dimmers and or master stations The cabinet arrives at the job site ready to accept power and load wiring from the installer This can significantly reduce installation time and potential wiring issues while providing a clean and consistent installation For design flexibility the cabinet accommodates several load types and device ratings To best suit the application the designer indicates where each device is located within the cabinet MultiSet Pro Pre Wired Dimmer Cabinet MDC20 is a U L c U L listed enclosure designed to hold up to 20 MultiSet Pro dimmers and masters which can be configured into one or more individual rooms Maximum wattage capacity is 20 dimmers at 1000W each total 20 000 watts or 10 dimmers at 1920W each total 19 200 watts For higher capacity applications multiple cabinets MHPWDC20 MDC20 MDCS56 may be wired together Note A single MultiSet Pro System purple wire network can accommodate up to 30 MultiSet Pro dimmers and masters When the total number of MultiSet Pro devices exceeds the 30 device limit use the dimming cabinet to accommodate one or more 30 devices MultiSet Pro Dimming Systems Blank plates are provided to cover all unused spaces The dimmer cabinet is surface or recess wall mounted All dimmers and components are serviceable or removable from the
11. oads One dimmed 120VAC Line Neutral per circuit Figure 14 fpe spe sfb olhe uses fs fff fo fo See Page 3 for Terminal Block He T oponga Wiring Descriptions 120VAC Line Neutral Note No Common Neutrals ae eee eee TAC Line Neutral i K 420VAC Line Neutral on Dimmed Circuits ii 120VAC Line Neutral Note Knockouts are provided See nen on top and both sides Ae 2 H E a 120VAC Line Neutral 120VAC Line Neutral l I 120VAC Line Neutral i 120VAC Line Neutral 120VAC Line Neutral 120VAC Line Neutral 120VAC Line Neutral i p H 120VAC Line Neutral ai 420VAC Line Neutral 120VAC Line Neutral 5 g g 0 g 120VAC Line Neutral i am 120VAC Line Neutral 120VAC Line Neutral 120VAC Line Neutral LHe ll Circuit Breaker Panel MHPWDC20 a Connecting Multiple Cabinets Figure 1
12. repair or replace any electronic controls product proven defective if it is returned postage prepaid to Lightolier Controls 10911 Petal St Dallas Texas 75238 Lightolier Controls will not pay for any charge back or charge for labor or material that does not have its prior written approval This warranty shall be in lieu of any other warranty express or implied including but not limited to any implied warranty of merchantability or fitness for a particular purpose Some states do not allow limitations on how long an implied warran ty lasts and do not allow the exclusion or limitation of incidental or consequential damages so the above limitation or exclu sions may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state This product may be covered by one or more of the following U S Patents 4 413 211 4 430 576 4 465 956 4 733 138 4 792 731 4 880 950 4 988 840 4 992 709 5 004 969 5 004 969 5 128 654 5 153 816 5 189 259 5 194 858 5 239 255 5 239 255 5 371 439 5 371 444 5 506 480 5 636 111 5 642 104 5 646 490 5 814 550 5 821 704 5 920 156 5 930 126 Des 307 578 333 124 435 203 440 207 License 4482844 5 004 969 5 239 255 and corresponding foreign patents Other Utility Design and Foreign Patents Pending We reserve the right to change details of design materials and finish in any way that will not alter the installed appearance or reduce f
13. rlay on these models is easily replaced even if the unit is currently installed Figure 4 1 Turn the power off at the circuit breaker 2 Remove the faceplate Figure 4 3 Remove the master keypad wall screws Figure 5 3a On heatsink model remove heatsink screws and spacers Figure 5 Remove the retaining plate screws and plate Figure 6 Remove the existing keypad membrane Install the new keypad membrane being careful to line it up properly with the openings 7 Reinstall the retaining plate and screws Figure 6 7a On heatsink model reinstall screws and spacers Figure 5 8 Reinstall the master keypad to wallbox Figure 5 9 Reinstall the faceplate Figure 4 10 Turn the power back on at the circuit breaker i D Faceplate Note Spacers on the heatsink model are not attached to the unit Heatsink Screws EPEA MUITISET PRO PRE WIRED DIMMING CABINET MDC20 Dimmer Switch Operating Instructions MUuLTISET PRO DIMMER To Turn light on to preset level tap top of rocker the dimmer fades up at the 1 5 second rate e A second tap of the rocker fades the dimmer to full brightness e To adjust the light level press and hold top or bottom of rocker until desired light level is reached and then release e To turn lights off tap the bottom of the rocker The dimmer fades at the 3 second fade rate e To quickly return to the preset level when light
14. rt number MDC20ENC Terminal Blocks Installed and positioned according to dimmer master FRONT configuration for each cabinet Red Terminal Blocks Load wire terminations Black Terminal Blocks Power feed terminations Blue Terminal Block MultiSet Pro purple wire terminations White Terminal Block Neutral wire terminations Grey Terminal Block Lightolier Controls PowerSpec HDF dimming ballast TAN wire termination MULTISET PRo PRE WIRED DIMMING CABINET MDC20 pore and Operation Replacing the Keypad Button Labels Classic Series MultiSet Pro Classic Series Masters are supplied with over 260 Figure 3 labels to personalize the buttons for your own scene names The buttons are labeled at the factory with letters These button labels P can easily be changed to customize your system 1 Insert a small screwdriver into the outside edge on the side ON gt of a button and pry off the plastic key cover CAUTION Pry from outside edge do not attempt to insert screwdriver between key covers Figure 3 A B Remove the factory label and insert an appropriate label from the supplied label sheet into the key cover Z Snap the cover over the button housing by pressing firmly on the plastic key cover Repeat for each button you wish to change N w gt A Replacing the Keypad Membrane Ellipse Series The ove
15. ty 3 While holding the Set button tap the top of the rocker to sequence the LEDs n Setb iten through the various fade rates until the desired fade rate is selected oe 4 Release the SET button 5 Repeat steps 2 4 for each device To change the fade rate that will affect only an individual scene 1 Tap a scene button on the Master to go to a scene 2 Press and hold the SET button 3 After 3 seconds either a single green LED or a pair of green LEDs indicates the scene s fade rate 4 While holding the SET button tap the top rocker until the desired fade rate is reached 5 Release the SET button 6 Repeat above for each scene Operating Instructions MULTISET PRo MASTER CLASSIC SERIES Tap the ON button to elegantly illuminate the entire area to the ON preset e Press and hold the ON button to brighten lighting level Tap the OFF button to fade lights to OFF Press and hold OFF button to lower lighting level Tap a scene button to access preset light levels e Two quick taps of any button including ON and OFF will fade lighting quickly Figure 11 Classic Series MULTISET PRO MASTER ELLIPSE SERIES e Press or Tap the ON button to elegantly illuminate the entire area to the ON preset Figure 12 e Press the RAISE button to brighten lighting level e Tap the OFF button to fade lights to OF
16. unction performance Specifications are subject to change without notice Lightolier Controls For technical sales assistance call 1 800 526 2731 A Genlyte Company Made in U S A Lightolier Controls 2006 10911 Petal Street Dallas Texas 75238 www lolcontrols com P N 85 1530
Download Pdf Manuals
Related Search