Life Fitness 97TI Treadmill User Manual
Contents
1. INTEGRITY SERIES TREADMILLS CST CLST amp 97TI ASSEMBLY INSTRUCTIONS M051 00K58 C379 Congratulations and welcome to the world of AT CFITROSS The following Component Lists and the step by step assembly procedures have been assembled to make the set up of this treadmill as quick and easy as possible Please take special note of the following important points prior to choosing a location and beginning assembly of the treadmill IMPORTANT SAFETY INSTRUCTIONS e DO NOT position the rear of the treadmill any closer than 6 5 feet 2 meters to the nearest obstruction It is recommended that the sides of the treadmill should maintain a minimum clearance of 1 64 feet 0 5 meters from the nearest treadmill or other obstruction e NOT locate the treadmill outdoors near swimming pools or in areas of high humidity DO verify the contents of the delivery carton against the accompanying parts listing prior to setting the cartons and shipping material aside If any parts are missing contact Life Fitness Customer Support Services at the number listed on the back page of this assembly instruction booklet Save the shipping cartons in case of return e DO read the entire Operation Manual prior to attempting to operate this machine as this is essential for proper use The Manual explains how to properly use the treadmill and helps you to train your staff effectively e placez PAS l arri re du tapis roulant dans un rayo2. MAIN WIRE HARNESS G through the FERRITE Close the FERRITE 1 al Tilt the FRONT CONSOLE R upright and in position over the REAR CONSOLE Q Secure the FRONT CONSOLE to the REAR using the previously removed eight Screws P Tighten the ScREws securely Do not overtighten the ScrEws Note Be careful not to pinch any cables when assembling the FRONT CONSOLE R to the REAR CONSOLE Q Co Locate the LEFT Accessory Tray 11 Carefully slide the tray into the top of the LEFT UPRIGHT 1 as shown until fully seated Secure the accessory tray to the LEFT Tor MOUNTING PLATE H using four SCREWS 21 Repeat the procedure for the RIGHT ACCESSORY TRAY 12 and RIGHT Top MOUNTING PLATE J Tighten all UPRIGHT BOLTS securely Replace the Motor Cover E and secure the Motor COVER to the FRAME C using the four previously removed ScREWS D Tighten the Screws securely Do not overtighten the SCREWS Replace the FRONT GRILL B and secure the FRONT GRILL to the FRAME C using the four previously removed SCREWS A Tighten the Screws securely Do not overtighten the Screws Locate one SCREW GROMMET 18 Insert the SCREW GROMMET into the square hole located above the top inside mounting bolt of the RIGHT UPRIGHT 2 Repeat for the remaining SCREW GROMMET and LEFT UPRIGHT 1 Locate one LOWER UPRIGHT COVER 10 Position the LOWER UPRIGHT Cover at the bottom notch of the RIGHT UPRIGHT 2 making
3. across the belt and deck with the notched end near the LEFT UPRIGHT MOUNTING BRACKET F 4 Unwrap the Main WIRE HARNESS leading from the LEFT UPRIGHT MOUNTING BRACKET F Feed the MAIN WIRE HARNESS through the LEFT UPRIGHT 1 Carefully tilt the LEFT UPRIGHT upwards and position the notched end of the LEFT UPRIGHT over the LEFT UPRIGHT MOUNTING BRACKET With the LEFT TOP MOUNTING PLATE H directed forward slide the LEFT UPRIGHT down over the LEFT UPRIGHT MOUNTING BRACKET and pre installed and WASHER until it rests on the FRAME C Secure the LEFT UPRIGHT to the LEFT UPRIGHT MOUNTING BRACKET using two Borts and WASHERS 20 8 24 Use one Borr and WASHER on the inside of the LEFT UPRIGHT and one BoLT and WASHER on the front side of the LEFT UPRIGHT Leave the Borrs loose at this time Note Be careful not to damage the Main WiRE HARNESS G when routing it through the LEFT UPRIGHT 1 or when sliding the LEFT UPRIGHT over the LEFT UPRIGHT MOUNTING BRACKET F Note Be sure the pre installed washer is on the outside of the LEFT UPRIGHT 1 when sliding it down to rest on the FRAME C PLATE J directed forward slide the RIGHT UPRIGHT down over the RIGHT UPRIGHT MOUNTING BRACKET K and pre installed BoLT and WASHER until it rests on the FRAME C Secure the RIGHT UPRIGHT to the RIGHT UPRIGHT MOUNTING BRACKET using two BoLTs and WASHERS 20 amp 24 Use one Bott and WASHER on the inside of the RIGHT UPRIGHT and
4. edge of the LEFT INSIDE HANDLEBAR SHROUD as shown Locate and position the LEFT OUTSIDE HANDLEBAR SHROUD 7 to match the LEFT INSIDE HANDLEBAR SHROUD Install the remaining portion of the HANDLEBAR GROMMET onto the LEFT OUTSIDE HANDLEBAR SHROUD as it is positioned to match the LEFT INSIDE HANDLEBAR SHROUD Secure the SHROUDS together using three Screws 15 Tighten the ScREWs securely Do not overtighten the Screws Repeat the procedure for the RIGHT INSIDE and OUTSIDE HANDLEBAR SHROUDS 6 amp 8 1 Co Locate the DisPLAY CONSOLE 9 Remove the eight Screws P from the back of the DisPLAv ConsoLE and separate the front of the DisPLAY ConsoLe from the rear Position the REAR CONSOLE Q over the LEFT and RIGHT Top MOUNTING PLATES H amp J as shown From the bottom of the LEFT and RIGHT MOUNTING PLATES secure the REAR CONSOLE using four SCREWS 17 Tighten the Screws securely Do not overtighten the Screws 14 Position and rest the FRONT CONSOLE R face down across the HANDLEBARS 3 Connect all CONNECTORS leading from the LEFT if equipped and RIGHT UPRIGHTS 1 amp 2 to the corresponding CONNECTORS located on the FRONT CONSOLE Feed any excess WIRE HARNESS into the UPRIGHTS Carefully route all WIRE HARNESSES through the WIRE HARNESS GUIDES S located at the lower left of the REAR CONSOLE Q Note Consoles for the European Union countries are equipped with a FERRITE T Open the Ferrite T Route the
5. one Bott and WASHER on the front side of the RIGHT UPRIGHT Leave the Botts loose at this time Note Be sure the pre installed washer is on the outside of the RIGHT UPRIGHT 2 when sliding it down to rest on the FRAME C 10 11 Locate both HANDLEBARS 3 Slide one HANDLEBAR GROMMET 27 over each HANDLEBAR The groove of the HANDLEBAR GROMMET should face outward With the bend of one HANDLEBAR 3 directed to the outside of the treadmill insert the HANDLEBAR into the RIGHT UPRIGHT HANDLEBAR BRACKET L as shown Be sure the handlebar mounting holes are aligned Repeat for the left side HANDLEBAR Locate the ERGo FRONT CROSSBAR 4 and position the ERGO FRONT CROSSBAR with the plastic COVER M facing upward and forward as shown Locate and slide the LEFT and RIGHT INSIDE SHROUDS 5 amp 6 over the corresponding ends of the ERGO FRONT CROSSBAR as Shown Slide the LEFT and RIGHT INSIDE HANDLEBAR SHROUDS towards the center of the ERGo FRONT CROSSBAR aS shown Note Be careful not to damage any wire harnesses that may be leading from the ends of the ERGO FRONT CROSSBAR 4 Install one FRONT CROSSBAR GROMMET 26 rounded end first over either end of the ERGo FRONT CROSSBAR 4 Position the grommets just over the end brackets to meet the overmolding Note Be careful not to damage any wire harnesses that may be leading from the ends of the ERGO FRONT CROSSBAR 4 Position the right end of the ERGO FRONT CROSSBAR 4 nea
6. f Manuel de l utilisateur v Verifiez si la console d affichage est sur le systeme m trique ou anglais R f rez vous aux r glages facultatifs relatifs aux syst mes de mesure dans le Manuel de l utilisateur v Consultez le Manuel de l utilisateur pour le r glage de l horloge en temps r el Lisez le Manuel de l utilisateur dans son int gralit avant d utiliser le tapis roulant Before attempting to operate your Treadmill it is imperative that you familiarize yourself with the contents of the Operation Manual If your Life Fitness treadmill does not respond as described in the OPERATION MANUAL contact the Life Fitness Customer Support Services at 800 735 3867 toll free within U S A Canada Refer to the OPERATION MANUAL for a contact list for International Offices Prior to your call please be sure you have located and noted the MODEL NUMBER amp SERIAL NUMBER The Model and Serial numbers for each unit are located on the back of the unit near the toe guard as well as under the left rear endcap
7. he treadmill to a power source IMPORTANT CHECK THE BELT EDGE UNDER THE TREADMILL TO VERIFY THE BELT DOES NOT INTERFERE WITH LIFE SPRING BRACKETS AND THE BELT IS PROPERLY SET WITHIN THE BELT GUIDES PHYSICAL DIMENSIONS WEIGHT LBS KG SET UP HEIGHT PHYSICAL DIMENSIONS INCHES CM 403 413 83 37 63 5 183 kg 187 kg 211 cm 94 cm 161 cm i mi 440 83 37 65 5 195 kg 200 kg 211 cm 94 cm 166 cm 410 420 83 37 63 5 186 kg 191 kg 211 cm 94 cm 161 cm PRE OPERATION CHECKLIST A digital version of the Operation Manual can be found on the attached CD v Ensure that all fasteners are tight v Make sure the STRIDING BELT is properly tensioned and aligned according to the Operation Manual v Check the operation of the STOP switch and tether switch assembly See Operation Manual v Confirm the display console is set to English or Metric units See Optional Settings ENG MET in Operation Manual v Refer to the Operation Manual for real time clock setting v Read the entire Operation Manual before using the treadmill LISTE DES VERIFICATIONS A EFFECTUER AVANT LA MISE EN MARCHE Une version lectronique du Manuel de l utilisateur peut tre trouv e sur le CD Y V rifiez si tous les dispositifs de fixation sont serr s Assurez vous que le TAPIS est bien tendu et align conform ment aux instructions du manuel d utilisation v V rifiez le fonctionnement de l interrupteur d ARR T et reliez le c
8. n de 2 m 6 pi de l obstruction la plus proche Les c t s de l appareil ne doivent pas se trouver moins de 20 cm 19 7 po du tapis roulant voisin ou de toute autre obstruction NE placez PAS le tapis roulant l ext rieur pr s d une piscine ou dans des endroits tr s humides e V RIFIEZ si l emballage contient toutes les pi ces de la liste jointe avant de le mettre de c t Si des pi ces sont absentes contactez l assistance client le de Life Fitness au num ro indiqu au dos de cette brochure d instruction de montage e V RIFIEZ si l emballage contient toutes les pi ces de la liste jointe avant de le mettre de c t Si des pi ces sont absentes contactez l assistance client le de Life Fitness au num ro indiqu au dos de cette brochure d instruction de montage Br COMPONENT LIST Part Description Part Description 1 Left Upright 2 Right upright 3 Handlebar left and right 4 Ergo Front Crossbar 5 Left inside handlebar shroud 6 inside handlebar shroud 7 Left outside handlebar shroud 8 Right outside handlebar shroud Lower upright cover left and right 9 Display console 10 0017 00101 1265 11 Left accessory tray 12 Right accessory tray 13 Handlebar cap 14 Rear frame endcap 45 Handlebar shroud screw 16 Endcap Upright cover screw 0017 00101 1770 0017 00101 1772 47 Display console Handlebar support screw 18 Screw gromme
9. r the large access hole on the inside of the RIGHT UPRIGHT HANDLEBAR doas dt Hen BRACKET L Align the ERGO FRONT CROSSBAR MOUNTING HOLES Activity Zone on the with those in the RIGHT UPRIGHT HANDLEBAR BRACKET and secure Ergo Front Crossbar using two Botts 19 from the inside of the treadmill and Nuts 22 Tighten the Botts securely Insert one ScREW 17 from under the RIGHT UPRIGHT HANDLEBAR BRACKET Tighten the ScREW securely Note The CLST model Position the left end of the ERGO FRONT CROSSBAR 4 near the large access hole on the inside of the LEFT UPRIGHT HANDLEBAR BRACKET N Feed the HEART RATE CABLE O into the access hole downward out the bottom of the LEFT UPRIGHT HANDLEBAR BRACKET Align the crossbar mounting holes with those in the LEFT UPRIGHT HANDLEBAR BRACKET and secure using two Botts 19 from the inside of the treadmill and Nurs 22 Tighten the Borrs securely Insert one ScREW 17 from under the LEFT UPRIGHT HANDLEBAR BRACKET Tighten the ScREW securely Note Be careful not to pinch the HEART RATE CABLE O if equipped when assembling the ERGO FRONT CROSSBAR 4 to the LEFT UPRIGHT HANDLEBAR BRACKET Feed the HEART RATE CABLE O upward through the top of the LEFT UPRIGHT 1 12 Slide the LEFT INSIDE HANDLEBAR SHROUD 5 near the LEFT UPRIGHT HANDLEBAR BRACKET N Position the HANDLEBAR GROMMET 27 at the end of the LEFT INSIDE HANDLEBAR SHROUD Install the HANDLEBAR GROMMET onto the inside
10. sure the top lip of the UPRIGHT Cover is engaged under the outside notch of the RIGHT UPRIGHT Secure the UPRIGHT Cover to the RIGHT UPRIGHT using one SCREW 16 Tighten the ScREW securely Do not overtighten the Screw Repeat the pro cedure for the LEFT UPRIGHT 1 and remaining UPRIGHT COVER Locate the UPRIGHT PLUGS 25 Insert one UPRIGHT PLUG into each of the two access holes located on the lower outside of the LEFT and RIGHT UPRIGHTS 1 8 2 A TW ANY A aM LM un Sn ND Ms Locate and press the HANDLEBAR Caps 13 over the ends of the HANDLEBARS 3 Be sure the HANDLEBAR Caps are fully seated Using two ScREWs 16 each attach the two REAR FRAME END Caps 14 to the FRAME C as shown Tighten the ScREws securely Do not overtighten the ScREWS The treadmill striding belt must be walked in for five minutes after assembly is complete Plug the treadmill into an appropriate outlet Turn the treadmill on at the on off switch Select QUICK START from the console Increase the speed to 3 mph 4 8 km h Start walking in the front left corner of the walking surface and drift to the back move to the center of the deck and walk towards the front and finally walking to the right corner and drifting to the back Continue pattern for five minutes Refer to the specific treadmill s Operation Manual for power requirements proper line cord routing and other critical product information before connecting t
11. t 0017 00101 1773 0017 00042 0326 19 Front crossbar screw 20 Upright mounting bolt 0017 00101 1774 0017 00101 1778 24 Accessory tray screw 22 Front crossbar nut 0017 00101 1780 0017 00103 0327 23 Linecord clip 24 Upright washer 0017 00042 0838 0017 00104 0335 25 Upright plug 26 Front crossbar grommet 27 Handlebar grommet el OF HANDLEBAR SHROUD SCREW 15 FRONT CROSSBAR NUT 22 SCREW GROMMET 18 Em ENDCAP UPRIGHT COVER SCREW 16 UPRIGHT WASHER 24 Eu DISPLAY CONSOLE HANDLEBAR LJ mmm SUPPORT SCREW 17 LINECORD CLIP 223 FRONT CROSSBAR SCREW 19 OL UPRIGHT MOUNTING BOLT 20 E Ep ACCESSORY TRAY SCREW 21 IMPORTANT DO NOT DISCARD THE SHIP KIT LOCATED ON TOP OF THE DECK AND BELT ALL NECESSARY COMPONENTS NEEDED TO COMPLETE THE INSTALLATION ARE LOCATED IN THE SHIP KIT NE JETEZ PAS LE KIT D EXPEDITION PLACE SUR LE DESSUS DU PLATEAU ET SUR LE TAPIS IL CONTIENT TOUS LES ELEMENTS NECESSAIRES POUR L INSTALLATION IMPORTANT Check the belt edge under the treadmill to verify the belt does not interfere with lifespring brackets and the belt is properly set within the belt guides 1 Remove the four SCREWS A securing the FRONT GRILL B to the FRAME C Remove the FRONT GRILL and set it aside 2 Remove the four Screws D securing the Motor Cover E Lift and remove the MOTOR COVER and set it aside 3 Locate the LEFT UPRIGHT 1 Lay the LEFT UPRIGHT
Download Pdf Manuals
Related Search